Search Documents

By Ludovic Charpentier

Production of metallic wires directly from liquid jets would avoid drawbacks of extrusion (space needed, damaging, cost?) and enable recycling. But liquid jets tend to break, due to capillary instabilities, unless a solid layer (coating or start of solidification) surrounds it. We recently developed a process to produce tin wires, cooled by water flow parallel to the jet. Superficial oxidization of tin produces a glass coating around the jet. Studies showed the length of wires increased when increasing speed of tin jets, and that water average speed should be the closest possible to the jet one to have smooth fibers. Producing 1 mm diameter wires is possible. The length of wires is limited by the experimental setup, which does not provide possibilities to coil the wire. Most of other metals do not generate glass-like oxides. The lack of coatings makes it necessary to reduce the capillary instabilities to obtain fibers.

Jan 1, 2006

By H. Dong, J. J. Valencia, L. Nastac

"A comprehensive computer model was developed to understand and optimize the centrifugal casting process for manufacturing TiC/Al-bronze friction drums. Performance of these components requires proper distribution of TiC particles, which is shown by dimensional analysis to be dominated by centrifugal buoyancy effects and solidification kinetics.The model addresses the following: (1) a rheology-viscosity model of the interference between moving particles, (2) engulfment (entrapment) or pushing of particles in the mushy region by the advancing solid/liquid interface, (3) nucleation and growth of equiaxed and eutectic phases, (4) effects of particle size, particle concentration, and cooling rate on the final grain size, and (5) the impingement effect of particles on the nucleation and growth kinetics of solidifying microstructure.Parametric studies were conducted using the computer model to investigate the effects of various process and material parameters on the distribution of TiC particles. The effects of the volume fraction, size, and morphology of the particles (including clusters and agglomerates) on the particle distribution were evaluated in detail. The complex interaction between the solidifying structure and insoluble ceramic particles in centrifugally-cast metal-matrix-composites was also investigated.The model predictions of particle distribution and microstructure were validated with experimental data for centrifugally-cast A356/SiC and TiC/Al-bronze alloys.This work was conducted by the National Center for Excellence in Metalworking Technology, operated by Concurrent Technologies Corporation under contract No. N00140-92- C-BC49 to the U.S. Navy as part of the U.S. Navy Manufacturing Technology Program."

Jan 1, 2000

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By Nobuaki Sato

For the recovery of uranium from spent nuclear fuel, sulfide reprocessing process, which consists of voloxidation, selective sulfurization, and magnetic separation or selective dissolution steps, are proposed. In this paper selective sulfurization of rare-earth oxides in the presence of uranium oxides was studied by thermogravimetry and X-ray diffractometry. In case of the mixture with UO2, the rare earth oxides R2O3 (R=Nd, Eu, etc.) were preferentially sulfurized by CS2 formingoxysulfides and sulfides, while UO2 remained at temperatures lower than 500 °C. When R2O3was mixed with U3O8, first, the reduction of U3O8 to UO2 occurred at low temperatures followed by the sulfurization of R2O3. The separation of rare earth elements from UO2 in suspensionsolution by the use of permanent magnet was examined. The advantage of the proposed process was also discussed by compared with current process.

Jan 1, 2006

By A. M. Ramalho

In the synthesis and sintering processes to obtain superhard materials, such as diamond and cubic boron nitride, deformable ceramic capsule is used as gasket to transmit and support the required high pressures and high temperatures, HPHT. The ceramics materials for these capsules should have special physics and chemical characteristics such as refractoriness, shear strength and compressibility. In this work, Bridgman?s anvil made of hard metal or speed steel was used to characterize some ceramics materials in terms of their maximum compressible thickness. Tests were also performed with different resin polymers used as binding mixture with ceramics powder. Chemical analyses and investigations through scanning electronic microscopic (SEM), X-ray and real tests for the synthesis of diamond were also performed. The results showed that local Brazilian calcite can be successfully used in the manufacture of HPHT gaskets.

Jan 1, 2006

By F. Z. Utyashev

The present work considers the essence of fragmentation: on the level of a simple model as a material response to the curvature accumulated by it at large deformations. It is on this basis that the correlation between curvature and fragment sizes is determined. It is shown that at deformation the area of curvature center inevitably changes. It is revealed that a specific value of variation of center surface area, i.e. ^As parameter, is numerically equal to the value of curvature acquired by a material. Minimum sizes of fragments and grains depending on ^As have been estimated, and the dependence of this parameter on strain has been established. Besides, the present paper considers the effects exerted by curvature center geometry, material distortion, directions of deformation and thermal warming up in the localization zones on structure refinement when various techniques are applied.

Jan 1, 2006

By Ovidiu Pasca

The Phelps Dodge Miami Smelter utilizes four Hoboken converters to process molten matte from the Isasmelt vessel. This paper presents past and present improvements in operation, maintenance and process optimization, based on data collection, which has led to increased converter campaign life and copper throughput.

Jan 1, 2005

By R. G. Reddy

Reduction of different chromite ores with carbon was studied as a function of C/FeO ratio and temperature in the range 700 °C to 1100 °C by thermogravimetry (TGA) analysis. Powders of chromite ore(-150 mesh) and carbon(-150 mesh) were thoroughly mixed in a desired proportions and were placed in the reaction crucible. The reduction rates of reactions were determined by continuously monitoring the weight loss as a function of time at constant temperature using TGA set up. The analysis of results suggest that FeO present in the chromite ores is reduced to Fe involving gaseous intermediates CO and CO2. The overall rate of FeO reduction is controlled by the oxidation of carbon. A kinetic equation, that of random nucleation, was proposed. The activation energies for the reduction of FeO, present in Roast Movat and Transvaal ores, with carbon were determined to be 55800 and 23000 J/mole, respectively. The results of the present study are compared with the data available in literature. The low activation energy values as determined in this study suggest that the carbon oxidation reaction is catalyzed. It is concluded from the present investigation that the low grade chromite ores can be significantly upgraded to higher value added chromite that can be used as a feed source for economical smelting.

Jan 1, 1998

By Flavio Begazo, William A. Enrico

"Southern Peru Copper Corporation's Ilo Refinery, the largest in Peru, began operations in 1975 with a production capacity of 165,000 stpy. Southern Peru bought the Refinery from the state owned Minero Peru SA on June 1, 1994.The Refinery processes blister from Southern Peru's I/o Smelter. Blister copper is processed in an anode plant equipped with two 365 st tilting reverberatory furnaces, a 26 mold casting wheel and an anode press machine. Copper is electrorefined in a tank house equipped with 768 commercial cells, 44 stripper cells, and 40 liberator cells, utilizing two electrolyte circuits and a 21,000 Ampere rectifier.During 1989 through 1994 a program for improving productivity was carried out by increasing the number of cells and increasing current density to the total rectifier capacity. As a result, a capacity 215,000 stpy of refined copper, 2 million tr. oz silver and 6,000 tr. oz gold per year was achieved. In 1994 Southern Peru announced plans to increase capacity to 250,000 stpy of cathode with a US$ 18 million investment and a US$ 2 million investment in environmental improvement projects, as part of the purchase agreement with the Peruvian government.This paper outlines the scope of the SPCC lio Refinery modernization and environmental program. It describes the implementation of the Electrolytic Plant expansion based on instaliation of polymer concrete cells, a new rectifier, a new selenium roaster and a Precious Metal Plant upgrades."

Jan 1, 1997

By Bowang Xiao

Recently more and more attentions are paid to high pressure hydrogen quenching (HPHQ) for its advantages such as environmental friendliness, low distortion, etc, compared to oil and water quenching. In HPHQ process, heat transfer coefficient (HTC) usually varies from part surface to surface because of the intense variation of gas velocity around the part. This article studies the effect of HTC distribution on part distortion after HPHQ and shows that finite element simulations considering HTC distribution predict different distortion from these without considering HTC distribution. It is also pointed out in this article that HTC distribution can be optimized by adjusting part orientation and HPHQ condition so that part distortion is minimized.

Jan 1, 2010

By Hiroyuki Matsuura

The effects of P2OS or Na2O addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at I 773K by isotope exchange method 1-6. The rate constant decreased with increasing P2Os content of molten oxides and the residual rate constant was observed at high P2OS content. On the other hand, the rate constant increased with increasing Na20 content for FexO-SiO2 melts, The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By Thomas Prietl

The use of gas stirring systems through the furnace bottom is common for anode and holding furnaces in the copper industry The first implementation of a gas stirring COP KIN® system in a Peirce-Smith converter was performed at the New Boliden smelter, Rönnskar, Sweden. In addition to other benefits, a decrease in process time and a decrease of the oxygen content in the blister copper were observed. To determine the effects of the gas stirring system and the process endpoint, an optical production control ?Semtech OPC system? was used. The light emission of the converter flame as an optical process parameter provides qualitative on-line process information, and is also used for endpoint determination of the slag making process, on-line control of iron content in white metal, quality control of slag etc. The results, benefits and risks of using the COP KIN® and OPC system for a Peirce-Smith converter are reported.

Jan 1, 2005

By J. M. Tannenbaum

A depth-sensing micro-indentation technique is developed for evaluating mechanical properties of materials at elevated temperatures (to 1200°C). System description and design considerations of the test apparatus are described. Based on Hertzian spherical indentation approach, the micro-indentation test apparatus is capable of determining Young?s modulus and creep strength of test materials with flat, tubular, or curved architectures from room to 1200°C under either air or controlled gaseous environments. Calibration tests were conducted on a H13 Tool Steel coupon from 22°C to 500°C and single crystal Haynes 230 alloy at 1000°C with excellent agreement to the literature values. Indentation creep tests of Haynes 230 alloy were carried out at 1200°C with preliminary results showing good correlation to creep exponents. Further system refinements will be investigated, and additional testing will be conducted.

Jan 1, 2010

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Xi Zhang

A technique for fabricating free-standing, high-aspect-ratio porous and pillar-type Ni structures has been developed using wet Si processing. A wafer of (100) Si was initially etched in HF solution to form deep pores with micron-sized diameter. The aspect ratio can exceed 200. By introducing the as-etched Si into a defined aqueous Ni2+ solution, Ni deposits grew rapidly onto the sidewalls and replaced the Si. Long-time immersion allows the Si sidewalls to be completely converted and thus form a metallic Ni structure with high-aspect-ratio pores. It is known that close-packed submicron Si pillars can be formed by oxidizing and subsequent etching of the macropore sidewalls. Treated in the same Ni solution, high-aspect-ratio Ni pillars were correspondingly emerged by replicating the original pillar-type Si structure.

Jan 1, 2006

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

By Sergio Neves Monteiro

This work had as its objective the characterization of a waste material, steel slag, generated from an integrated steel plant, with a view to its recycling and incorporation into red ceramics fabrication. The characterization was performed in terms of chemical composition by X-ray fluorescence (XRF), particles size distribution, X-ray diffraction (XRD), thermal analysis (DTA/TG) and scanning electron microscopy (SEM). The results indicate that the steel slag presents high amount of Ca, Fe, Mg and Si. The weight loss of the steel slag at temperatures above 800oC is associated with calcium carbonate decomposition. The coarse particle size of the steel slag is inadequate for its direct recycling into red ceramic fabrication. It is necessary to screen or to grind the waste. As a possible solution, it is suggested that screening or grinding the steel slag to a convenient particle size distribution would allow its successful industrial incorporation into red ceramics products.

Jan 1, 2006

By Esher Hsu

In Taiwan, around 8,000 tons of batteries are consumed per year but only 17% of which were collected and transported to oversea for recovery. The dumping used batteries have become a potential environment problem. How to increase the collection efficiency of used batteries is an important issue for EPA in Taiwan. Besides, some treatment plants are on process to get permission for recovering used batteries. The objective of this study is to estimate the recycling cost of spent consumer battery and explore the feasibility of recovering used consumer batteries in Taiwan based upon the principle of cost-efficiency. The recycling cost including collection cost and recovery is estimated based on a survey. Results would provide some suggestions to Taiwan EPA regarding feasibility of recovering used batteries in Taiwan.

Jan 1, 2006

By Rodney L. Williamson

Optimal estimation theory has been applied to the problem of estimating process variables during vacuum arc remelting (V AR), a process widely used in the specialty metals industry to cast large ingots of segregation sensitive and/or reactive metal alloys. Four state variables were used to develop a simple state-space model of the V AR process: electrode gap (G), electrode mass (M), electrode position (X) and electrode melting rate (R). The optimal estimator consists of a Kalman filter that incorporates the model and uses electrode feed rate and measurement based estimates of G, M and X to produce optimal estimates of all four state variables. Simulations show that the filter provides estimates that have error variances between one and three orders-of-magnitude less than estimates based solely on measurements. Examples are presented that verify this for electrode gap, an extremely important control parameter for the process.

Jan 1, 2001

A novel pressure leaching process for platinum group metal (PGM) feedstocks is described. The process is particularly well suited for treatment of ores or concentrates that are too low grade for economic processing by the conventional smelting/leaching process. Operating conditions have been identified under which gold, the PGM's and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGM's, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow NilCo concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGM's from the pressure leach product.

Jan 1, 2000