Search Documents

By T. C. Goel, A. Venna, R. G. Mendiratta

"Processing of ferrites has gained tremendous importance in recent times to meet the high performance demands on ferrites in keeping with the fast emerging· technologies. The quality of ferrite powders has strong influence on ·the performance of final device. Fabrication· of high performing ferrite components requires starting ferrite powders of precise stoichiometry, purity and microstructure. It is difficult to obtain these attributes by the conventional ceramic method. The key to obtaining quality powders lies in the· solution techniques. With this in view soft ferrites have been prepared by a wet chemical process, known as the citrate precursor method, which involves the formation of citrate complexes of the constituent cations. The advantages of this process are the ease of preparation and close control of composition, homogeneity, purity and particle size. Electrical and magnetic measurements on lithium ferrites have shown resistivity higher by more than two orders of magnitude compared to that observed for samples prepared by the conventional ceramic method, and low magnetic losses, making the ferrites specially suitable for high frequency applications.IntroductionProperties of ferrites are known to be sensitive to .their processing technique. A small deviation in the compositional stoichiometry of the ferrite affects its properties greatly. Soft ferrites such as Ni-Zn, Mn-Zn and Mg-Mn. are well known ferrites covering wide-ranging applications [1,2]. Lithiiim ferrites have also assumed technological importance for microwave applications and are potential substitutes for the expensive garnets [3]. Lithium ferrites are often doped with zinc to tailor the saturation magnetization required at high frequencies. Lithium and lithium-zinc ferrites, however, present difficulty to processing due to the volatile nature of both the cation components, namely Li and Zn. These ions are volatile at temperatures > 1000°C which makes their processing difficult. One of the main considerations of high frequency performance of ferrites is the high eddy current losses which prevent the interaction of the magnetic field with the ferrite component and hence impair device performance. These losses can be reduced by having a material of high resistivity. Electrical conductivity in lithium ferrite has been attributed to electron hopping [4] between the two vaience states of iron, Fe2+ <=> Fe3+, on octahedral sites. Maintaining the + 3 valence state of otahedral- Fe ions is thus a prerequisite for achieving high resistivity. The resistivity of ferrites is normally found to be low when processed by the conventional solid-state or the ceramic method [5]. This is attributed to (a) extensive ball-milling employed in the method to mix the component oxides results in non-stoichiometric compositions due to introduction of additional Fe ions on abrasion of steel balls during milling, (b) high processing temperatures involved which result in significant volatilization of Li and Zn ions creating thereby oxygen non-stoichiometry which results in reduction of Fe3 + to Fe2 +, (c) large and non-uniform grain sizes. In the present work, preparation of Li and Li-Zn ferrites by a non-conventional method known as a citrate precursor method [6, 7] which requires lower processing temperatures and duration is reported. The method gives stoichiometric compositions on account of homogeneous atomic-scale mixing of the constituent cations via the formation of metal-citrate complexes mixed in solution state. The method is also capable of giving small grain size which aids the oxidation ofFe2+ ions."

Jan 1, 2000

By Guo Xueyi

The morphological characteristics of the nickel particles electrodeposited from chloride dominant aqueous solution was investigated. The effects of the electrolyte constituents, the parameters for the electro-deposition on the morphology of the nickel particles were addressed. It is evidenced that not only the particle size but also the morphology of the deposited nickel particles strongly depend on the electrolyte constituents and technical operation conditions. The electro-crystallization mechanism of the metallic nickel particles deposited at high current density was elucidated. The ultra-fine nickel particles with flake, nodular or dendrite shape may be produced by controlling the duration for electro-deposition.

Jan 1, 2003

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

The effects of microwave roasting on separation of rhenium (Re) and molybdenum (Mo) from a molybdenite concentrate have been investigated based on evaluation of the heating characteristics of the concentrate in the microwave field. The results show that a variety of operating variables, namely microwave power, sample weight, sample geometry, roasting temperature, roasting time and atmosphere significantly impact on the volatilization rates of Re and Mo. The optimum conditions for Re-Mo separation are microwave power 1300 W, sample weight 20 g, sample geometry pellets, temperature 600 oC, time 1.5 h, and atmosphere 20%O2. Under these experimental conditions, the volatilization rate of Re reaches 88.12%, while that of Mo is just 5.15%. Microwave-assisted roasting provides an alternative route to separating Re and Mo from molybdenite concentrate.

Jan 1, 2016

By Guo Xian Jian

In this paper, the effects of matte grade, flux grain size, blast flowrate and blast O2 content on the process of silica flux melting in a copper converter were investigated. The results showed that the blast flowrate and the blast 02 content were not significant factors in the melting process. However, with an increase in grain size of flux and grade of matte, the amount of the flux molten decreased. The data on the melt rate of process correspond well with the mathematical model which simulates the chemical reactions occurring at the interface. The kinetic equations of melting are as follow:

Jan 1, 1996

By S. B. Bortnikova

This paper presents the results of an investigation of the gold-silver oxidized ores at the Salair mine. West Siberia. High losses of precious metals during primary ore processing are the result of outdated technology that is not suited to treat the present ore compositions. The main mineralogical forms of gold and silver and their confinement to different grain size fractions have been determined. About 50% of gold in the slime fraction and 60% of the silver in the form of acanthite that are scattered from the secondary minerals are lost to the waste. The results of these investigations have provided the basis for the recommendation of a new technological process to upgrade the current practice of the gold extraction plant and for methods to reprocess the concentrates.

Jan 1, 1995

By Demaerel. J. P.

Arsenic plays a major role during electroreflning of copper. Both the arsenic content in the anode and the arsenic concentration of the electrolyte have, in conjunction with other impurities such as lead, antimony, bismuth and oxygen, a direct influence on the quality of the cathode. The mechanisms are currently slime. inclusion and precipitation of insoluble compounds in the bulk of the electrolyte. Arsenic has also been reported to have a depassivating effect on the anode. An influence on the anode slime adhesion has also been found. A literature survey is given and these data are compared with and completed by our own results based on lab and pilot scale experiments as well as on Olen tank.house practice.

Jan 1, 1987

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By Joseph C. Rota

The Carlin Trend is one of the most significant gold mining districts in North America. Located in northeastern Nevada, a total of over 17 million ounces of gold have been produced since 1965 at Newmont Gold Company's open-pit and underground operations. Oxidized portions of the sediment-hosted, disseminated gold deposits at Carlin generally consist of finely disseminated concentrations of sub-micron sized native gold particles hosted in Paleozoic siliciclastic or carbonate rock. Oxide ore is commonly amenable to dump leach or heap leach processing, yielding an average 50 to 70% recovery of total contained gold. Refractory unoxidized ore requires some form of pretreatment oxidation to ensure economic gold recovery. Geologic ore control is typically combined with standard assay and engineering techniques to maintain both grade and metallurgical control ofleach grade ores. Mine geologists provide a vital function through field observation and recording ofmineralogic data during daily, visual blasthole logging. Intricately mixed refractory materials must be separated from oxide ore to ensure highest possible gold recoveries. Geologic information is combined with assay data to create mine polygons in an engineering computer database. Mining selectivity is further enhanced by in-pit ore control geologists who are available to make production decisions based on direct mineralogic observations at active mine faces.

Jan 1, 1997

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By S. L. Kher

The Singhbhum Copper Belt located in the state of Bihar in Eastern India bears evidence of ancient workings and indicates the existence of a civilized habitation in this region in the past. It was in 1833. how- ever, that the first official announcement of the occurrence of copper in the district was made. Although the occurrence was confirmed in 1847, it was not until 1857 that the first company was formed to exploit the deposits. This Company was dissolved in 1859 and from then until 1920, there were many unsuccessful attempts to develop and exploit the copper deposits in the Singhbhum area. In 1920. the Cordoba Copper Co. took an option on the Mosaboni area, which is nearly 10 km away from the present works located at Moubhandar, Ghatsila and exercising the option in 1924, purchased the mining rights from the Cape Copper Company. The Cordoba Copper Co. was then converted into Indian Copper Corporation Ltd. This was subsequently taken over by the Government of India in March 1972 and is now known as Indian Copper Complex (ICC), forming one of the two smelting units of Hindustan Copper Ltd.

Jan 1, 1976

By L. Sh. Tsemekhman

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By John A. Clark, Danylo Oryshchyn, Casey Carney, Stephen Gerdemann, Cathy Summers, Thomas Ochs

"Limited analysis of combustion gas streams where carbon capture is not of interest is done mainly to ascertain operation parameters. Stringent regulations on acid gases and particulates promote careful flue gas analysis. Unregulated components are typically not analyzed. Typically not more than four points (two in the boiler, and one each in the flue and the stack) are sampled. A successful oxy-fuel process with carbon capture and compression is anticipated to require as many as 12 sample points with analysis for water, nitrogen, oxygen, argon, NOx, SOx, and carbon monoxide. Carbon dioxide captured for beverages produces a high value product and the cost associated with analysis is warranted. However, carbon capture for disposal must keep all costs to a minimum. This paper will compare alternative approaches for cost-effective sampling and analysis of the carbon dioxide product streams from oxy-fuel combustion, through all stages of production through compression and pipeline/vessel delivery.IntroductionAnalysis of gases in an oxy-combustion process with carbon capture is essential to the operations of the oxy-fired boiler and the subsequent collection, compression, and purification of carbon dioxide. The process is charged with pure oxygen and not-so-pure carbon in the form of coal at the front end, generating a product of mainly carbon dioxide with traces of argon, nitrogen, sulfur compounds, nitrogen compounds, oxygen, hydrogen, and mercury. It is possible that hydrogen chloride and hydrogen sulfide may also be present in trace amounts [1]. The trace components primarily come from impurities contained in coal such as water, sulfur, nitrogen, and volatile organic compounds. Coal also contains a good deal of mineral matter that is transformed into ash during combustion, becoming particulates that can complicate the analysis regimes utilizing standard analytical equipment."

Jan 1, 2010

By Kathryn A. Mrotek

The textural growth patterns of nodules from two areas in the North Pacific and the South Pacific are characterized by mottled, columnar and compact-type zones. Amorphous material (mainly iron and manganese hydrox-ides) is a botryoidal-forming phase in the mottled and columnar zones. Crystalline material (platy crystals of birnessite and crystallites of todo-rokite) is found primarily in the mottled zones on botryoidal structures or as long-protruding structures growing onto that portion of the nodule in contact with the underlying sediments. The long-protruding mottled zones contain little or no biogenic debris, suggesting that these zones grew un-interruptedly within the underlying sediments. The coalition of spheroidal knobs comprising some of the nodules also suggests a relatively long residing time within the sediments. It appears that crystalline material (the usual host to associated valuable metals) forms in a quiet environment and as a result of direct nodule association with the underlying sediments.

Jan 1, 1982

By Chao Du, Xiaohui Ning, Hongmin Zhu, Qiuyu Wang, Shuqiang Jiao

"TiCxOl-x solid solutions were synthesized by sintering a mixture of titanium carbide and titanium monoxide at 1600 °C. The corresponding structures and morphologies of the TiCxOl-x solid solutions were characterized by XRD and SEM. A series of tests has been performed on the electrochemical dissolution behavior of TiCxOl-x solid solutions in NaCl-KCl molten salt. The influences of synthesis time and electrokinetic parameters on the anodic dissolution behavior were also investigated. The results showed that TiCxOl-x solid solutions can dissolve as Tin+ into alkali chloride melt. Titanium ion species dissolved from TiCxOl-x solid solutions changes between Ti2+ and Ti3+ depending on the applied potential. The tail gas on the anode was monitored by a mass spectrometer. It was found the synthesis time significantly affects the components of the anodic gas.IntroductionTitanium and titanium alloys have been desired greatly because of their many uses. The critical factor that restricts the range of uses for Ti is its high cost of extraction. The primary titanium metal, sponge titanium, is still produced industrially worldwide by a process invented by Dr. Kroll in the 1940s[1] •Since the early 1970s, the research focus of the titanium industry has been directed towards developing a continuous process to produce high purity titanium at low cost. [2-10] Of the many alternative methods that have previously been investigated, the electrolytic process has been considered a promising method for titanium metallurgy [4-10]. Recently, several electrolysis and related methods such as the PFC-Cambridge process[11-15], calciothermic reduction[16-18], USTB [19,20] and MER[21] process were extensively investigated.The USTB process is a new approach where the pure titanium can be directly obtained by the electrolysis with an anode of titanium oxycarbide in molten salts[19, 20]. The titanium oxycarbide was produced by carbothermal reduction of titanium dioxide under vacuum at a temperature"

Jan 1, 2011

By R Bartlett

Process engineering-science originally developed for percolation leaching of ore in heaps is extended to the decontamination of unsaturated soil, either in situ or after excavation and emplacement as a soil heap on an impervious pad. Phenomena considered include: soil matrix porosity and permeability; percolating solution retention, capillarity and flow; washing sweep efficiency; optimum solution application rates during leaching; soil agglomeration to improve soil permeability and soluble contaminant transport by diffusion in soil agglomerates. Practical aspects briefly discussed include leach pad construction, solution distribution and recovery from the soil, and solution containment.

Jan 1, 1994

By Dietmar Eifler, Marcus Klein, Hendrik Kramer

Conventional methods to characterize the fatigue behavior of metallic materials are very time and cost consuming. That is why the new short-time procedure PHYBALCHT was developed at the Institute of Materials Science and Engineering at the University of Kaiserslautern. This innovative method requires only a planar material surface to perform cyclic force-controlled hardness indentation tests. To characterize the cyclic elastic-plastic behavior of the test material the change of the force-indentation-depth-hysteresis is plotted versus the number of indentation cycles. In accordance to the plastic strain amplitude the indentation-depth width of the hysteresis loop is measured at half minimum force and is called plastic indentation-depth amplitude. Its change as a function of the number of cycles of indentation can be described by power-laws. One of these power-laws contains the hardening-exponentCHT eII, which correlates very well with the amount of cyclic hardening in conventional constant amplitude fatigue tests. To identify heat-treatment-parameters and SAE 52100 TRIP-alloys with high hardening rates as well as their damage tolerance the PHYBALCHT- and PHYBALLIT-method were used. One modified SAE 52100 TRIP-alloy was investigated in detail. The fatigue behavior and the cyclic hardening of the selected SAE 52100 TRIP-alloy was investigated and compared with conventional SAE 52100. Conventional stress-controlled fatigue tests were performed on a servo-hydraulic test system with a frequency of 5 Hz and a load ratio of R = -1. Different rates of cyclic hardening were identified. The size of the nonmetallic inclusions leading to crack initiation and the number of cycles to failure were used to evaluate differences in the damage tolerance capability.

Jan 1, 2015

By J. L. Jambor

Sulfide-rich tailings accumulated in a 4l-hectare impoundment at the Waite Amulet minesite near Noranda, Quebec, have undergone partial oxidation and destruction of the principal sulfides (pyrite and pyrrhotite) in the vadose zone. Mineralogical studies and whole-rock chemical analyses of 18 samples from 3 boreholes along a cross-section of the tailings pile indicate that the principal chemical manifestations of the alteration are a pronounced depletion in sulfide-sulfur, and an enrichment in total Fe as Fe203&apos; Other elements such as Al, Mn, Mg, Ca, Na, and K in the solids show erratic or inconsistent variations, but a trend to Si enrichment in the oxidation zone is clear. The trend is interpreted to be a relative enrichment whereby the proportion of the stable silicate minerals has increased as a consequence of the consumption of pyrite and pyrrhotite in the oxide zone.

Jan 1, 1989

By Minh H. Pham

This paper presents a technique for imaging the extent of solidification of molten metal flowing in a cooled pipe based on the concept of eddy currents. A 3D mathematical model, which relates the geometry of solidification to the scattered field induced in a solenoid external to the pipe, is derived. The model is described by a set of integral equations which are solved numerically using the moments method. An iterative algorithm is developed to reconstruct the solidification distribution image. Experimental measurements have shown that the eddy current technique is sufficiently sensitive for practical purposes.

Jan 1, 2001

By M. Shevchenko

Integrated experimental and modelling research program on the phase equilibria and development of thermodynamic databases of the lead and copper metallurgical gas/ slag-matte-metal-solids systems (PbO-“Cu2O”-FeO-Fe2O3- ZnO-CaO-SiO2) is being undertaken to support improvements in the pyrometallurgical smelting and recycling processes. This is the first systematic investigation of phase equilibria of slag systems in equilibrium with Pb metal, providing information for systems in which copper coexists in slag with lead or zinc as major components. The experimental studies involve high-temperature equilibration of synthetic samples, rapid quenching, and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). FactSage-based thermodynamic database development is integrated with experimental research. Initial thermodynamic assessments are used to identify priority compositions and conditions for experiments, which are planned to provide specific data to assist thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved. Continuous database improvement and extension to include new elements are targeted. Example of industrial application is given.