Search Documents

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By Wiraseranee. Chompunoot, Kazuki Morita, Toru H. Okabe

"Aiming at the development of more effective recycling processes, dissolution behavior of rhodium into molten slag was investigated. Using a pure rhodium crucible and Na2O-SiO2 slag system, equilibration experiments were carried out for 18 h at 1423-1623 K under various oxygen partial pressures of 0.005-1 atm with varied slag basicity. Rhodium solubility increased with increasing oxygen potential, slag basicity, and temperature. Rhodium dissolved into slag as rhodate ion ([RhO2]-) by the endothermic reaction: Rh(s) + 3/4O2(g) + 1/2O2-(in slag) = [RhO2]-(in slag). In the dissolution reaction, the “rhodate capacity” of slag is newly-defined. The correlation between rhodate capacity and optical basicity is reported.IntroductionDue to its high chemical resistance and outstanding catalytic properties, rhodium (Rh), one of the platinum group metals (PGMs), is utilized in various applications such as catalysts, molten glass vessels and containers, and electronic devices. Owing to the rarity of Rh resources in nature, recycled Rh from scraps such as spent automobile catalytic converters is currently considered as an important source of Rh supply [1]. According to the recycling practices, Rh is currently mainly recovered from scraps along with other PGMs such as platinum (Pt) and palladium (Pd) by a dry process (e.g., smelting), a wet process (e.g., leaching and subsequent separation of PGMs from aqueous solution), or a combination of both processes [2]-[4]. Among these processes, smelting is commonly applied because PGMs can be effectively separated from a relatively large amount of various impurities coexisting in scraps. In the smelting process, Rh and other PGMs are collected in the collector metal (e.g., iron and copper), and impurities in scraps are removed into slag [4]-[6]. The process may be carried out at a temperature range of 1573-1973 K, in either an oxidizing or reducing atmosphere. Due to the high oxidation resistance at high temperatures, Rh is expected to be collected efficiently in the metal collector rather than being oxidized and forming RhOx in a molten slag. However, Rh loss into slag does occur in this process [7]."

Jan 1, 2011

By Ross R. Bhappu

A theoretical and experimental investigation into pyrometallurgical refining of chloride leach/electrowin copper is described. The two techniques investigated were (i) vaporization and (ii) gaseous halogenation. Experiments were carried out with a packed bed of electrowon copper crystals and a boat of melted copper crystals. Nitrogen gas and Freon 12/nitrogen mixtures were used as the carrier and reac.tive gases. Vaporization was found to be effective in removing Bi, Pb and S while halogenation was effective. in removing As, Bi, Pb, S and Sb. Silver resisted all attempts at removal. Iron was removed but less effectively than the other impurities.

Jan 1, 1985

By Chu Yong Cheng

Manganese is one of the main impurities in the recovery of base metals from their ores. This is especially true when laterite ores are processed using the pressure acid leach (PAL) process. The use of intermediate precipitation, solids/liquid separation and re-leach in the three Western Australian nickel laterite plants to separate nickel and cobalt from manganese and other impurities makes these processes complicated and costly in capital and operation. The research work carried out by the solvent extraction (SX) group at the A J Parker Cooperative Research Centre for Hydrometallurgy (CSIRO Minerals) has led to the development of direct solvent extraction processes to separate nickel and cobalt from manganese and other impurities. The simplicity of the process flowsheets and the expected savings in capital and operating costs are the major advantages of the new direct solvent extraction processes over the existing processes. By using a new synergistic organic system, Versatic 10 / dccyl-4-pyridinccarboxylatc ester, with a pilot plant leach solution from BHP¬Billiton (after iron precipitation), the metal values (Ni and Co) together with zinc and copper were separated from manganese and other major impurities (Mg, Ca and Cl) in the first SX circuit. The co-extracted manganese, magnesium and calcium were easily scrubbed out. The extraction and stripping kinetics of the metals with the new synergistic organic system were very fast and the synergistic system was found to be chemically stable. pH-extraction isotherms of metals with D2EHPA showed that the extraction order as a function of pH50 was Zn2+ > Ca2+ > Mn2+ > Cu2+ > Co2+> Ni2+> Mg2+. Semi-continuous test work with a cobalt pilot plant leach solution from Peko Rehabilitation Project Pty Ltd and a synthetic solution to simulate a concentrated laterite leach solution from BHP-Billiton showed that manganese, together with calcium, copper and zinc can be separated from nickel, cobalt and magnesium. This led to the development of another direct solvent extraction process to separate manganese and other impurities from nickel and cobalt and to recover nickel and cobalt from leach solutions. A project was initiated by HiTec Energy Ltd to recover manganese from waste laterite leach solutions using SX technology and to further purify it to produce high purity electrolytic manganese dioxide (EMD) for the high quality alkaline battery industry. Batch tests were conducted to select a suitable organic system for the extraction of manganese in terms of selectivity and extraction and stripping kinetics. A total of eight organic systems were tested using waste laterite processing solutions. A Versatie 10 / synergist system showed very promising results. By using the synergistic system, high manganese recovery would be obtained, fewer SX stages would be required and a higher A:O ratio could be used in extraction, resulting in a smaller organic inventory and lower capital costs. The risk of gypsum formation is also minimised with the synergistic system. Keywords: Solvent Extraction, Manganese, Laterite, Synergist

Jan 1, 2004

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Masayoshi Matswnoto

The Kosaka Smelter and Refinery produces copper and lead, and has a history of more than 100 years as a metallurgical department of Dowa?s Kosaka Mine. The Smelter treats complex sulfide concentrates which are difficult to smelt. Valuable metals are recovered using various processes developed by Kosaka Smelter and Refinery. Effluent waters from the smelter contain large quantities of heavy metals. This paper describes how Kosaka Smelter and Refinery recovers valuable metals from various effluent waters and handles overall waste waters in order to meet strict environmental standards.

Jan 1, 1993

By Xinlei Jia, Wenming Guo, Yanling Zhang

A large amount of stainless steel dust rich in Fe, Cr, and Ni has been being generated in China. Smelting treatment is accepted as a practical method for the recovery/reutilization of these second resources, during which Fe, Cr, and Ni is reduced into one metal phase and then separated from the residue slag. Based on the typical compositions of stainless steel dust, the residual slag can be termed as CaO-SiO2-MgO-Al2O3 system. In this paper, the activity coefficients of Cr in Fe-Cr-Ni-C (-Si/Al) melt and the properties of CaO-SiO2-MgO-Al2O3- 1%CrO system thermodynamically approached. Then, in laboratory experiments, the recovery ratios of Cr and its distribution behaviors between Fe-Cr-Ni-C melt and CaO-SiO2-MgO-Al2O3 slag system were examined.

Jan 1, 2015

By Jaroslav Horskoý, Miroslav Raudenský, Bogdan Filipic, Božidar Sader

This paper describes main elements and practical use of the computational system for automated setting of optimized casting conditions in the continuous casting of steel. The system consists of the heat transfer model of the process, empirical metallurgical criteria, and optimization algorithm. The physical model of the, strand temperature distribution relies on the classical Bennon-Incropera mixture continuum formulation for the convective-diffusive heat transport. Fluid flow effects are considered through enhanced thermal conductivity of the liquid phase. The model is solved by the operator-splitting Crank-Nicolson finite volume version of the Voller-Swaminathan scheme. The solution procedure is coupled with the IDS solidification analysis package. Boundary conditions for the strand cooling rely on combination of the generic and plant-specific mold, spray, and roll heat transfer coefficients ' by coping the effects of the casting speed, casting temperature, casting powder, mold oscillation mode, steel grade, water or air-mist spray type, running water, trapped water on the rolls, and radiation. The caster safety and productivity and the quality of the strand are related to nine empirical metallurgical criteria. The criteria ensure the caster safety and economy as well limit the internal, longitudinal, and transversal surface cracking possibility. The problem of finding optimum casting parameter values is stated as a minimization problem based on the analytical form of the cooling criteria evaluated from the steady-state temperature distribution of the strand. To solve the optimization problem, a genetic algorithm is employed. The algorithm explores process parameters settings heuristically by applying the principles of biological evolution. It starts with a random set of solutions and iteratively improves them through selection and variation. Solutions are evaluated by running the heat transfer model of the process and extracting the values of the empirical metallurgical criteria.

Jan 1, 2000

By Z. Smieszek, J. Botor, Z. Miczkowski, S. Sobierajski

"From 1978, the direct process for the smelting of chalcocite concentrates in a flash furnace by the Outokumpu method has been applied at the Glogów II copper smelter. The chemical composition of these concentrates make it necessary to control the process very strictly. In this paper, the method for controlling and measuring the main technological parameters of the copper production by flash smelting is being presented. It includes the determination of the chemical composition of the concentrate, its grain structure, the temperature of liquid products of the process, oxygen content in process gases, as well as lead concentration in copper and copper concentration in slag.The main process parameters are determined from the mass and energy balances. The relations between parameters, such as an effect of grain structure of a concentrate on oxygen and oil consumption, and dependence of chemical composition of a concentrate on capacity and products quality are discussed. 1. IntroductionThe Polish copper concentrates, as most concentrates occurring worldwide, contain from 18% to 30% Cu, and less sulphur (7-11%) and iron (2-5%). The main copper-bearing mineral contained in the concentrates is chalcocite, while bornite and chalcopyrite are present in smaller quantities. Moreover, the organic carbon (5-7.5%), arsenic (0.05-0.3%) and lead (1.2-3.0%) are also contained in the concentrates. The gangue consists mainly of silica, aluminosilicates, calcium carbonate and magnesium carbonate. Their proportions make the addition of slag-forming agents unnecessary.The composition of Polish concentrates, especially their low iron content, allows their application in the direct flash smelting process for blister copper production. Low sulphur content is the factor which determines the necessity of oxygen application in this process."

Jan 1, 1989

The paper describes the propensity of tin to form intermetallic compounds with microalloying elements such as Nb, Ti and aluminium, which are commonly used as additions to achieve particular combination of strength and toughness. Two series of alloys were prepared by arc melting under an argon atmosphere. Each series was based on Fe, Sn and A1 with either Nb or Ti additions. The microstructures were studied using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and microprobe analysis. It was found that the level of Nb addition has an effect on the formation of Sn-rich compounds. For small Nb additions, no Sn containing compounds were found, whereas in higher Nb alloy, a Laves phase (FezNb, hexagonal, a = 0.4830 nm and c = 0.7879 nm) containing about 1 at % Sn was found. A FezNb3 phase (cubic, a = 1.1261 nm) associated with the formation of alumina was also found but did not contain tin. No Sn containing compounds were found with Ti additions. The experimental observations have been compared with thermodynamic calculations performed using MTDATA.

Jan 1, 1999

By James W. Evans, Dong Xu, Jr. Jones

A physical (water) model based on particle image velocimetry (PIV) has been constructed at UC Berkeley. The PIV technique enables the use of water modeling to quantitatively characterize the fluid flow behavior in the mold during the continuous casting of steel, in a whole field sense, i.e., section by section. A method to obtain e\e time-averagevelocity (TA V) vector maps was developed by averaging 40 instant aneous vectc -r plots revealing the time average features of the flow. Another benefit of TAV vector maps is the ability to compare with present mathematical models, which are mostly based on the time-average technique. Bifurcated submerged entry nozzles (SEN) with ports inclined at various angles to the horizontal were used in the modeling to study their effects on the flow inside the caster. Argon was also introduced into the model to simulate the influence of argon injection on the metal delivery from the tundish into the caster. The bubble sizes and distribution (in specific sections) of argon were characterized, at the same time, by the imaging system of the PIV. This will allow for validation of current mathematical models that were developed to simulate argon injection in casters. Comparison with results calculated by the commercial finite element package FIDAP is also presented.

Jan 1, 1998

By L. Filip

The roast-leach-electrowinning (RLE) process for zinc was modified to treat two typical complex concentrates containing zinc, lead, copper, gold and silver. Laboratory testwork results indicated that the optimum roasting temperature ranged from 700 to 800°C, in order to produce acceptable residual sulfur levels. The calcined concentrate was subjected to a three-stage leach sequence. The resulting leach solution was purified by hematitic precipitation and directed to the recovery of copper and zinc by solvent extraction and electrolysis. Alkaline smelting and subsequent electrolytic purification recovered the lead and precious metals from the leach residue. A flowsheet was developed based on the laboratory testwork results, and demonstrated in a large-scale pilot plant. The recoveries produced during the pilot plant operation ranged from 90 to 92% for zinc and copper, 85% for lead and 90% for gold and silver, respectively.

Jan 1, 1999

By Y. A. Chang, J. Woodford, C. R. Kao

Reactive diffusion studies between NbC and Si were carried out at 1300 °C under a vacuum of 10-5 torr and a uniaxial pressure of 1 MPa. The annealing time ranged from 8 to 100 hours. The Si used was single crystal silicon; the NbC was hot-pressed powder compact. A NbSi2+SiC two-phase reaction layer formed with NbSi2 as the matrix and SiC as discontinuous particles. The microstructure of the reaction product is homogeneous, dense, and fine. The NbSi2 grain size and SiC particle size are in the micron range. The growth of the reaction products follows parabolic kinetics. Extrapolation of the data to zero thickness suggests an apparent incubation time of 3.5 hours. However, for short annealing time «60 hours), the thickness data can be approximated by linear kinetics with an initial growth rate of about 2 11m/hr. Based on these experimental observations, a growth mechanism for the reactive diffusion between Si single crystal and NbC powder compact is proposed. We propose that the nucleation sites for the SiC particles are at the voids of the NbC powder compact. This proposed nucleation mechanism offers a potential way of controlling the SiC particle size by changing the void size and void density of the NbC powder compact. This hypothesis, if proven to be true, will allow us to control mechanical properties of the composites by tailoring the SiC particles formed. It is also pointed out that the microstructure requires Si to be the dominant diffusing species and to diffuse through the reaction layer, while Nb and Conly have to undergo local rearrangement.

Jan 1, 1996

By Donna L. Bodine

The ability of oxidized Upper Freeport bituminous coal to adsorb Cu2+, Cd2+ and Mn(VII) from very dilute aqueous solutions has been studied. Low-rank coal is known to adsorb heavy metal ions from dilute, aqueous solutions, probably by ion exchange and/or chelation by acidic functional groups on the coal surface. However, it would be advantageous to use higher rank coals for water treatment. Coal samples were oxidized thermally or by 30% H202 to increase the surface concentration of phenolic and carboxylic groups, then portions were shaken with Cu2+ and Cd2+ solutions. Acidic KMnO4 was also used to oxidize coal, with concurrent sorption of the resulting Mn(IV) and Mn(ll). The effect of oxidation treatment, metal ion concentration, and solution pH on metal uptake kinetics was investigated. Potential applications for treating effluents, especially those containing oxidizing ions, are discussed, along with possible flowsheet options.

Jan 1, 1995

By Masami Taguchi

"It is found that lead monoxide, PbO, has an ionic conductivity, and the all solid-state electrochemical cell using this oxide as an electrolyte has attracted the attention of battery researchers. In this study, thin film PbO2/PbO/Pb solid cells were produced on glass substrates and their discharge properties were investigated. The acti.ve material for the positive electrode, PbO2, was obtained by reactive sputtering of a Pb target in oxygen plasma. The PbO electrolyte and the active material for the negative electrode, Pb, were vacuum evaporated from /3 -PbO powder and a Pb block, respectively. The open-circuit voltage of the cell agreed with the theoretical value based on the thermodynamic data, and the close-circuit voltage was improved by the addition of a univalent impurity such as sodium or potassium to the PbO electrolyte. The connection of the cells in series and in parallel produced a higher electromotive force and a larger capacity. Also, the charge-discharge cycling test revealed that the cell could be charged and function as a storage battery.IntroductionGenerally, the ionic conductivity of a solid-state electrolyte is lower than that of a liquid electrolyte near room temperature. This has been a serious obstacle to using such electrolytes in an electrochemical cell. However, some solid-state electrolytes, which can preferentially pass a specified ion and have high ionic conductivity, have been found. Lead monoxide, PbO, which is an oxygen ion conductor, is such an example (1)(2). If a solid-state electrolyte is adopted for use in an electrochemical cell the problem associated with a liquid electrolyte such as leakage can be alleviated. The cell structure also can be simplified, because the electrolyte plays the role of separator to prevent the active materials from mixing. Thus, physical vapor deposition technology may make it possible to develop a very thin film cell, which consists of only solid phases (3)(4). In this study, the thin film PbO2/PbO/Pb solid cell with a thickness· of only a few micrometers, in which all the constituents were systematically deposited on a glass substrate by reactive sputtering and vacuum evaporation, has been produced and the charge-discharge properties were investigated. An attempt was made to improve the discharge properties by doping impurities such as Na2CO3 and Sb2O3 into the PbO electrolyte. Moreover, the connection of the cells in series and in parallel to get a higher electromotive force and a larger capacity, and the charge-discharge cycling test to determine its use as a storage battery were carried out."

Jan 1, 2000

By Magnus Ek

After the installation of three new converters as part of the recent expansion of the Rönnskär smelter completed in 2000 work continues to further improve the converter operation. The converter upgrade led to an increase in blister copper taps from 150 tons per batch to more than 300 tons. The total cathode copper production increased from 130,000 tons in 1999 to 230,000 tons in 2001, the first year in full production. In recent years focus has been to improve operating practise, maximize the blowing time, extend the converter campaigns hence to reduce the specific brick consumption and improve the converter slag composition.

Jan 1, 2005

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By Jonkion M. Font

An expression for the distribution ratio of arsenic between slag and copper matte or liquid copper was developed by both, an extension of the Reddy-Blander model for deriving a priori the arsenic capacity, and by a relationship between the arsenic capacity and the arsenic distribution ratio. In this study, the a priori arsenic capacities in the FeO-SiO2, CaO-SiO2, MgO-SiO2, FeO-CaO-SiO2, FeO-FeO1.5-CuOo.5-MgO-SiO2, FeO-FeO1.5-CuO0.5-CaO-MgO and FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slags were calculated at 1573 K. The a priori arsenic distribution ratio between the FeO-FeO1.5-CuO0.5-CaO-MgO-SiO2 slag and copper matte (L s/m as), and between the FeO-FeO1.5-SiO2 or FeO-FeO1.5-CuO0.5-CaO-MgO slag and liquid copper (L s/Cu as) were calculated. The model calculated data are found to be in good agreement with the reported experimental data. The availability of reliable thermodynamic data for slag components and impurities in the slag-matte-metal system is essential for the accurate prediction of impurity capacities and distribution ratio data. The arsenic distribution ratio model developed here, can be extended for prediction in multi-component slags and mattes or liquid metal, and thereby may lead to the development of new slag systems for the efficient removal of arsenic in the copper smelting, converting and refining processes.

Jan 1, 2003

By R. Hurman Eric

The flow of molten slag and matte and the estimation of the mass of settled matte in electric furnaces is discussed and the action of the electric furnace as a settler is considered. Particle size of the concentrate and its grade are major contributors to settler dimensions. Discussion on the production capacity of the electric furnace with reference to operating current, power input, furnace dimensions such as width and length and electrode diameter are given. These discussions are based on considerations derived mainly from experimentally determined properties of the slag such as its resistivity, viscosity and liquidus temperature. Extension of the design and operating considerations to circular furnace symmetry is also discussed.

Jan 1, 1995

By George Kazonich

The high costs and environmental problems associated with making iron and steel in the United States is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 325-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993