Search Documents

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By Jesse L. Craft

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops. Sag subsidence develops where the pillars are failing in conjunction with roof failure. Overburden thickness is generally greater than 150 feet. Beam subsidence can occur in all terrains. It is associated with retreat mining and room and pillar mining where pillar crushing or pillar compression has taken place and barriers are left inplace. They occur as beam arch or one-sided beam subsidence. Beam arch failure occurs where mining has taken place on both sides of a coal barrier. One-sided beam failure is associated with retreat mining moving from a barrier towards the entry in hilly topography. This type of subsidence occurs where a hard, thick, rock unit is acting as a bridge supporting the overburden and outcrops on the hill side.

Jan 1, 1992

By Uwe Wyink, Guenther Thiele, Isabel Gollnick, Klaus Thyrock

"The application of a thin spray on liner was implemented in longwall T-junction sections in 2009 for the first time. The development of the material and the application is based on a technical cooperation between RAG Deutsche Steinkohle AG and BASF Corporation. The report gives an overview of the first trials. The underground test occurred in a seam with a height of 1.5 m (5 ft) in a depth of 1,100 m (3,609 ft). The roadway is dual-use entry and the roof strata is composed of shale and sandy clay. In some sections geological faults impact the surrounding strata. The poor conditions induce separating and loosening of roof rock. Several remedial actions have to be implemented for decreasing deformations at the face entrance.The application of thin spray on liner (TSL) provides simplification and cost reduction of supporting work at longwall T-junction. The installation of TSL to avoid roof and coal fall operations for lagging are omitted.INTRODUCTIONFor safe operation of face retreat in dual-use roadways, the processes of securing and stabilizing the face end area are very important in order to minimize deformation and stress. Avoiding roof and coal fall are the main concerns for safe operation. For that reason different methods of reinforcement are tested in underground operation. In this paper the application of TSL is presented.The specifications of TSL are described, followed by the case study results. The underground study is located in one mine of RAG Deutsche Steinkohle. The extraction of the hard coal in this mine is characterized by great depth and high stress. There are poor geological and geotechnical conditions. The roadway used for the underground application was headed with the support system combination type A, which will be described later in the paper. After the first face retreat, deformation of steel arch support and bagging destroyed the roadway, so for the second face retreat remedial actions had to be undertaken. For this a new system of reinforcement, simplifying the supporting work at the longwall T-junction was tested. The reinforcement consisted of different parts that are described in the following report. Furthermore two different versions were applied. One method is the operation with TSL and the other one is the use of concrete for sealing. Both methods are compared in the text."

Jan 1, 2010

By Jesse Puller, Ken W. Mills, Owen Salisbury

"An underground coal mine located in New South Wales has a target coal seam located 160-180 m deep directly below a 16-20 m thick conglomerate unit that has been associated with significant periodic weighting events on the longwall face. As part of the investigations to better understand the causes of periodic weighting at the mine, inclinometers capable of measuring horizontal shear movements through the full section of the overburden strata were installed ahead of mining at two locations approximately 1 km apart above the centre of two longwall panels. These inclinometers were monitored as the longwall approached each site. This paper presents the details of the installation, the results of the inclinometer monitoring at both sites, and the insights that these measurements provide for overburden behaviour about longwall panels.Horizontal shear movements were observed to develop on shear horizons that correlate closely across the two sites suggesting a mechanism that is consistent across a large area of the mine. Shear movements were observed to develop on a single horizon near the top of the conglomerate strata that was mobilised almost immediately after initial formation of the longwall goaf at a distance of 425 m ahead of the longwall face. The direction of horizontal movement was consistent with the relief of the major principal horizontal stress. As the longwall face approached each inclinometer, other horizons within the upper part of the overburden strata begin to shear with the upper strata moving toward the approaching goaf more than the lower strata. Within the last 30 m of longwall approach, tilting of the strata associated with the increase in vertical subsidence toward the extracted goaf caused a change in the style of deformation with tilting and reverse shear offsets.INTRODUCTIONLongwall mining is recognised from subsidence monitoring, surface extensometer measurements, and various other observations to cause significant disturbance to the overburden strata directly above the extracted goaf of each longwall panel. Disturbance to the overburden strata beyond the limits of each longwall panel is not so well understood. Subsidence monitoring indicates that horizontal movements beyond the edges of the extracted longwall panel are generally greater in magnitude than vertical subsidence and horizontal movements may extend up to several kilometres from the edge of the panel in some circumstances (Reid 1998, Reid 2001, Hebblewhite et al 2000, Mills 2001, Mills 2014). The mechanics of how these movements are accommodated within the overburden strata is only poorly understood and there are few direct measurements."

Jan 1, 2015

By Sahendra Ram, Arnn Kr Singh, Dheeraj Kumar, Rajendra Singh

"Inherent existence of different rooms (openings) along the extraction line in a depillaring panel provides an easy path for the goaf to encroach the working area. Each of these openings in a mechanized depillaring (MD) operation along the extraction line is supported by the roof bolt-based breaker line support (RBBLS) to restrict the goaf encroachment. Different field studies by Council for Scientific and Industrial Research - Central Institute of Mining and Fuel Research (CSIR-CIMFR) found that the RBBLS works effectively during the depillaring under the shadow of stable surrounding ribs/fenders only. It is observed that, generally, these natural supports experience high value of induced stresses after a large amount of void creation inside the goaf. The induced stress creates spalling/loosening of the sides of the natural supports. Field studies also found that the positions of the RBBLS at the goaf edge need to be adjusted according to the depth of this spalling/ loosening. However, a systematic study in field for the correct positioning of the breaker line as per the spalling/loosening under different site conditions is difficult. Therefore, on the basis of the data and guidance provided by these field investigations, a detailed parametric investigation was conducted in the laboratory on simulated models for an effective design of RBBLS in a MD panel. FLAC3D is used for the simulation of the depillaring, and the available empirical formulations for Indian coalfields are used for subsequent calibration. An analysis of stress redistribution for different stages of the MD in simulated models showed the significance of the nature of overlying strata/induced stress for the RBBLS design. Discussing some results of field studies, this paper presents results of the laboratory investigations for an effective design of the RBBLS.INTRODUCTIONContinuous Miner (CM)-based mechanized depillaring (MD) is an important issue for Indian coalfields, where huge amounts of coal are locked up in standing pillars (Dixit and Mishra, 2010). Considerable variations in site conditions of these developed pillars bring a number of technical challenges into consideration during their final extraction. One of these challenges is goaf encroachment/overriding during caving of the competent roof strata. Goaf encroachment/overriding can effectively be controlled, mainly, by suitable design of natural supports (rib/snook/fender). However, there is a requirement of applied supports against the immediate roof as a considerable portion of this roof is exposed due to the presence of different openings along the line of extraction. These applied supports act as a fulcrum at the goaf edge between the working area and the goaf to facilitate the break out of the hanging roof inside the goaf. This is called breaker line support. An effective breaker line support is important for the efficiency of a depillaring operation. Generally, MD adopts roof bolt-based breaker line support (RBBLS) at the goaf edge (Singh, et al., 2014). For the first time in India, roof bolts were applied at the goaf edge as RBBLS in a CM-based MD (Leeming, 2003). In the beginning, three rows of roof bolts were installed as primary and secondary breaker lines support. On the basis of the observations of instrumented bolts, only two rows of roof bolts were used as secondary RBBLS (Ram, et al., 2014). Now, most of the MD operations in India are using only two rows of bolts as RBBLS (Table 1). However, the strata mechanics studies at different MD operations showed interesting characteristics resulting from this support (Ram, et al., 2015)."

Jan 1, 2016

By Pieter-Jan Kleiterp

Caterpillar has been involved in highwall mining since the purchase of Bucyrus in 2011. The Cat® HW300 is a continuation of the Superior Highwall Miner that was first sold in the USA in 1994. Currently, there are more than 80 machines supplied worldwide, and Caterpillar envisions increasing the population steadily in the coming years. The Cat highwall miner product group, based in Beckley, WV, has been involved in the sales of all miners to date. With the dealer model that Caterpillar is using, more people, dealers in particular, need to be trained on the application of highwall mining. A site investigation is a highwall specialist?s work, and Caterpillar assists dealers and customers in determining the technical feasibility of highwall mining on mine sites. With the ever-increasing amount of requests, it proved to be important that people without highwall mining expertise, yet who are familiar with mining, could perform a very quick analysis of a potential highwall mining site to determine at an early stage if it is worthwhile to invest the time and money of all parties?customer, dealer, and Caterpillar?in further follow-up. Therefore, Caterpillar would like to introduce the Cat HW300 QuickScan tool.

Jan 1, 2014

By Kewal K. Kohli, Stefanie Self

"Three cases of surface subsidence investigated over abandoned coal mines after flooding in one case and dcwatering in two cases are presented in this paper. Mining was conducted by the room and- pillar method at all the mines leaving stable pillars. This paper will discuss the background chain of events and the likely causes of the pillar failure resulting in surface subsidence.CASE NO.1BackgroundThe Pittsburgh scam was mined in 1960 by the room-and- pillar method, leaving pillars (Figure I) through Mine A. located in Monongalia County. West Virginia.The mining height in U1is area was 1.83 m (6 ft) with an average mining depth of 140 m (460 ft). The mining recovery was 62% and the safety factor of the pillars was calculated at 1.15 using the Bieniawski ( 1984) fom1ula. For stable pillar design. a 1.5 safety factor is recommended. A 1.15 safety factor is considered marginal. Pumping continued after the mine was shut down in 1960 to prevent water seeping into an adjoining mine owned by the same company. The pumping ceased on December 12. 2003, and the mine was allowed to flood. The water level rose about 17 m (55 ft) by August 3 1, 2004, based on observations in a nearby borehole. On September 3, 2004 surface subsidence occurred above this area causing damage 10 a residence (Figure 2).Summary of InvestigationThe floor of the Pittsburgh coal scam played a strong role in the pillar failure. In this area, the immediate floor of the Pittsburgh seam consists of about two feet of fireclay. Extensive damage to the surface house was an indication that a major collapse below the surface had occurred. The pillars supporting the overlying strata were evaluated to find the cause of their failure. The pillars in the Pittsburgh seam (sec Figure I) had a marginal safety factor of 1.15 before flooding and were stable for 26 years. Once the mine was flooded the water level in the Pittsburgh seam rose by 17 m (55 ft). Shortly thereafter the fireclay in the floor weakened, resulting in several pillars punching into the floor unevenly making the immediate roof unstable. The overburden strata supported by these pillars also subsided do"" n into the mine, causing damage to several house on the surface."

Jan 1, 2010

By Anthony (Sam) J. S. Spearing

Backfilling using coal waste is not a novel means for waste disposal throughout the world; yet, backfilling using a high density (paste) backfill is relatively new, except in Germany and Poland. One of the main benefits of a high density backfill, as opposed to a low density (slurry) backfill, is that, if placed at a low permeability and low moisture content, the risk of water table contamination can be relatively low. In addition, if paste backfill can be placed cost effectively, environmental benefits are huge because the surface impoundment footprint can be greatly reduced or even eliminated. This is especially true in room-and-pillar applications. In its current state, backfilling is considerably more costly than surface disposal. This is mainly because paste, as opposed to slurry, significantly increases backfill placement costs; however, this could be offset by increasing the achievable extraction rate. Overall, such a system could potentially improve the public?s image of coal mining in the US for a myriad of reasons. This paper discusses a proposed backfill system for a typical room-and-pillar coal mine in the Illinois Basin of the US and clearly shows the technical advantages, although costs are still higher with fill. The cost differential will likely reduce over time, in favor of the backfill option, as costs of traditional surface disposal increase, due mainly to ever-restrictive disposal regulations.

Jan 1, 2013

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By Morgan Sears

The LaModel program (Heasley, 1998) is a displacement discontinuity, boundary element model (BEM) for analyzing stresses and displacements in single and multiple-seam coal mines. After the Crandall Canyon mine collapse, the need for better design guidelines for LaModel was observed and a new calibration method for deep cover pillar retreat was developed (Heasley et al., 2010). However, the scope of this initial calibration was limited to single-seam mines deeper than 750 ft. This limited application of the initial calibration method lead directly to the research presented in this paper, which attempts to define appropriate LaModel calibration guidelines for pillar design where shallow cover and/ or multiple-seam mining scenarios are encountered. As part of this research, a database of shallow cover case histories has been developed, and this database is used to help validate the shallow cover calibration method. By adding the shallow cover database to the previous deep cover database, the LaModel calibration method has now been extended to the complete range of mining depths, as well as to multiple-seam cases. With this shallow cover calibration, the utility of the LaModel program continues to increase.

Jan 1, 2013

By Houquan Zhang, Ming Li, Guimin Zhang, Bei Zhang

"The support quality of bolts in deep roadways is one of the important factors for efficient and safe coal production. A new kind of non-destructive testing technique and equipment was used to monitor the axial bolt load in real time in deep roadways. Based on the test results, the working status of bolt support in deep roadways was evaluated. The research results show that the variation characteristics of axial bolt load is consistent with the distribution characteristics of rock pressure no matter whether it is in the initial support stage or mining disturbance stage. The axial load of bolts located 20m outby the development face has an overall rising trend within 3-5 days after installation. Within a certain distance in the front abutment pressure zone in front of the face, the axial bolt load increases with the advance of coal extraction. When coal and rock in the abutment pressure zone yield, the axial bolt load is dropped correspondingly. This kind of non-destructive testing technique provides an advanced means of detection and evaluation on bolt support quality.INTRODUCTIONMany coal seams more than 800m deep are being mined in eastern China. Roadways of large cross-section are being developed in coal seams more than 600m deep in western China (Kang et al. 2014). Moreover, these roadways are commonly supported by roof bolts and have encountered many support problems, including soft rock strata, intense mining disturbance, and abnormal tectonic stress. The stability of its surrounding rocks is difficult to maintain, the roof bolt even fails before mining (Shen 2014; Jiang et al. 2015). Therefore, it is very important to develop an effective method to detect the bolt quality in real time and evaluate the bolt's safety status.During installation of roof bolt, the installation quality is heavily affected by installation equipment and tools, field conditions, and operators' skills (Li et al. 2005; Shan 2009). The anchorage length will be shorter than the designed one if the resin cartridges are pushed to the bottom of excessively long drill hole and stay there without being shredded and mixed. The support function of the bolt would be weakened by the shorter anchorage length."

Jan 1, 2016

By Ismet Canbulat, John Naylor, Jason Emery, Peter Craig, Andy Sykes

"Longwall mining is by far the most common method of underground coal extraction in Australia. The industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. The longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin encapsulated bolt installation is still the principal method used in all major coal-producing countries around the world. Anglo American realised an opportunity existed to introduce an alternative roof bolt installation technique called “spin to stall” in Australia. Spin to stall was first introduced in Anglo American Coal in South Africa where it has been successfully used for over a decade, though implementation of South African spin to stall resin in Australia has proven to be near impossible due to a significant difference in geotechnical conditions, mining method, and, subsequently, roof bolting equipment. Therefore, a new spin to stall development project was initiated between Anglo American Coal and Jennmar Australia (SPIN2STALL®). This paper summarises the journey of this project, the results, and the successful implementation of spin to stall achieved at Grasstree Mine.INTRODUCTIONThe Anglo American Coal business unit operates Grasstree and Moranbah North underground longwall mines in the Bowen Basin of Central Queensland, with a third longwall mine, Grosvenor, currently being developed, and two more (Aquila and Moranbah South) in the project pipeline. The vision for Anglo American is to achieve “Zero Harm” through the effective management of safety at all operations, while for the coal business unit, at the same time to achieve industry-leading operational performance. Currently, both Grasstree and Moranbah North longwalls are operating at industry best practice rates. This is placing increased pressure on the development process to allow such high productivity levels to be sustainable."

Jan 1, 2015

By William J. Conrad, Ryan J. Molka, Erik C. Westman

"In order to study pillar and overburden response to retreat mining, a ground control program was conducted at a Central Appalachian mine. The program consisted of several monitoring methods including a seismic monitoring system, borehole pressure cells in the pillars, and time-lapse photogrammetry of the pillar ribs. Two parallel geophone arrays were installed, one on each side of the panel with the sensors mounted 3m (IO ft) into the roof. A total of fourteen geophones recorded more than 5,000 events during the panel retreat. A MIDAS datalogger was used to record pressure from borehole pressure cells (BPCs) located in two adjacent pillars that were not mined during retreat. A series of photographs were taken of the pillars that had the BPCs as the face approached so that deformation of the entire rib could be monitored using photogrammetry.Results showed that pillar stability and cave development were as expected. The BPCs showed an increase in loading when the face was 115 m (380 ft) inby and a clear onset of the forward abutment at 30 m (100 ft). The photogrammetry results displayed pillar deformation corresponding to the increased loading. The microseismic monitoring results showed the overburden caving inby the face, again as expected. The significance of these results lies in two points, I) we can quantify the safe manner in which this mine is conducting retreating operations, and 2) we can use volumetric technologies (photogrammetry and microseismic) to monitor entire volumes of the mine in addition to the traditional point-location geotechnical measurements (BPCs).INTRODUCTION AND BACKGROUNDExcavation of underground openings is a difficult job in a challenging environment. The rigor of the process is compounded by the lack of a method that allows quantification of changes within the rock mass as excavation progresses. Statistics kept by the Department of Labor, Mine Safety and Health Administration show that 16% of fatalities and lost time incidents in the underground mining industry are due to unexpected rock mass failure (MSHA, 2015). A recent example is the Crandall Canyon, Utah, coal mine accident caused by the vertical collapse of a longwall coal mine on August 6, 2007 (Dreger, Ford, Walter, 2008)."

Jan 1, 2016

By Peng-Fei He

CT scanning tests were used to detect the pre-existing fracture systems of 36 cubical coal blocks. Systematic procedures were developed to construct the pre-existing fracture geometry of the cubical coal blocks from the CT images. Based on the constructed fracture systems, the fracture tensor components were calculated to capture the directional effects of the fracture system of the cubical coal blocks. The effect of the pre-existing fracture system and different combinations of confining stresses on the strength and deformability of coal masses was investigated at a preliminary level using some true triaxial test results and the computed fracture tensor components. The strength of the cubical coal blocks in the loading direction was found to be closely related to the summation of the fracture tensor components in the two perpendicular directions to the loading direction and the level of the confining stress system. The deformability of cubic coal blocks in the loading direction was found to be correlated to the fracture tensor component in the same direction.

Jan 1, 2014

By Morgan M. Sears, Mark Van Dyke, Gamal Rashed, John Rusnak, Khaled Mohamed

"In 2016, room-and-pillar mining provided nearly 40% of underground coal production in the United States. Over the past decade, rib falls have resulted in 12 fatalities, representing 28% of the ground-fall fatalities in U.S. underground coal mines. Nine of these 12 fatalities (75%) have occurred in room-and-pillar mines. The objective of this research is to study the geomechanics of bench room-and-pillar mining and the associated response of high pillar ribs at overburden depths greater than 1,000 ft. This paper provides a definition of the bench technique, the pillar response due to loading, observational data for a case history, a calibrated numerical model of the observed rib response, and application of this calibrated model to a second site. INTRODUCTION Bench mining is a an underground mining technique typically applied to room-and-pillar mines where full seam extraction on development presents an unacceptably high risk of injury from high pillar ribs or where the mining equipment is not designed to extract the full seam thickness. To mitigate the increased risk associated with high ribs and slender pillars, a more modest thickness is extracted from the top of the seam on development. This is followed by grading the floor and recovering the bottom of the seam with or without extraction of the pillars during retreat mining. A mine located in Eastern Kentucky extracts two seams at depths ranging from outcrop to 2,000 ft. In some areas of the mine, Seam A and Seam B are close enough together to be mined simultaneously. Seam A (top) is mined on development 7 to 9 ft. high for the entire length of the panel. On retreat, as each pillar is extracted, the continuous miner is ramped down into the floor (Seam B), two pairs of Mobile Roof Support (MRS) units are set, and the pillars are extracted at the full mining height of 14+ ft. During the pillar recovery process, the floor is extracted in each entry, from a ramp initiated outby the retreat line, sequentially just prior to extracting the lifts from the pillars (see Figure 1)."

Jan 1, 2017

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By Kazem Orace, Navid Hosseini, Mehran Gholinejad

"Selection of the optimum support system for underground openings such as tunnels is a complex process. In this paper a new approach, based on a combination of the Analytical Hierarchy Process (AHP) the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) and the Preference Ranking Organization METHod for Enrichment Evaluations (PROMETHEE), is introduced. For this purpose, the selection process is assumed to be a multi criteria decision-making problem. First different support systems using FLAC3D numerical code, based on technical safety and stability parameters of the tunnel are specified. Then taking economic and performance parameters as the decision criteria by using the combination of Al-IP, TOPSIS, and PROMETHEE the optimum support system is selected. As a real mine case study this approach is used in the main access entry to the C, coal scam of Tabas collieries. Results clearly demonstrate that the proposed support system selection method is more advantageous than other alternatives.INTROD CTIONGenerally, the support system for a tunnel is selected primarily with the aid of design engineers experience. In other words personal judgment instead of intellectual and scientific criteria is mostly the main basis (Oracc. 2005). However since various support systems can be applied in any particular situation, accurate selection of the optimum support method depends on the integration of many technical, economical and performance parameters, and also on the analysis of the intensity of influence by each of the criteria.In this paper an applicable approach for se lection of tunnel support systems based on Multi Attribute Decision Making (MADM) techniques including: Al IP (Orace et al.. 2009a; Saaty, 1980), TOPSIS (Hwang and Yoon, 1981: Yoon and Hwang, 1995), and PROMETHEE (Brans and Vincke. 1985; Brans and Mareschal. 1992) is introduced. As a field study, this approach was applied to tunnel C1 as one of the main entries in the Tabas coal mine which is the major collieries in the central pan of Iran (Hosseini, 2008).Due to the coal seam conditions coal is mined by mechanized longwall mining (Hosseini 2008). This method requires the 58 excavation of several entries some of which will be used for many years and even for the entire life of the mine (Peng, 2006). Therefore the selection of the support system in these entries is·very important in mining design."

Jan 1, 2010

By Wojciech Masny, Andrzej Walentek

"The most common extraction method in Polish coal mines utilize pillars between adjacent longwall panels. This is mainly due to the significant depth and difficulties in maintaining stability of the gateroads. This paper presents measurements of entry convergence and range of the fracture zone around a gateroad measured with a borehole camera. The entry where the measurements were taken was located in a parallel entry separated from the gateroad by a 5-m- (16-ft-) wide pillar. The gateroad was located in a hard coal seam 900 m (2,952 ft) deep with a dip of 5°. The extraction method was longwall mining with caving and the mining height was about 3 m (10 ft).Furthermore, the ""in situ"" measurements were compared to the convergence forecast for the gateroad and fracture zone by means of numerical modeling conducted using the Phase2 Version X.X finite element program from Rocscience. The determination of the fractured zone around the openings is of great importance to successful mining practice, especially in support planning and design for longwall gateroads. Moreover, proper determination of the fractured rock zone is one of the basic elements in the process of planning the roof bolting for mine workings.INTRODUCTIONIn the Polish. hard coal mining sector, retreat longwall extraction is most commonly used (Prusek and Masny, 2007). This method is connected with the necessity to carry out a number of development operations during the first stage, including among others, driving of gateroads and a setup room.Currently, most Polish mines eliminate gateroads behind the extraction front, using the ""U"" ventilation system (Szlitzak et al., 2008). In such cases, one of the roads for the next longwall panel is driven along the caving goafs, leaving a protective pillar of some chosen width (Figure 1). The question regarding the width of the coal pillar is especially important to the stability of the gateroads that define the panel for the subsequent longwall. When analyzing the previous experience relating to this type of pillar (Junker, 2006; Rajwa, 2008; Stranzet et al., 1973; Betriebsempfehlung, 1982), one can state that there exist two solutions for the determination of its width."

Jan 1, 2010

By Jinwang Zhang, Zhaohui Wang, Jiachen Wang

"Thick coal seams (seam height larger than 3.5 m) account for a large portion of the proven coal reserves of China, and underground thick coal seam mining provides about 50% of the Chinese annual coal production. Such seams are mainly mined using the longwall top-coal caving (LTCC) method. For safe and successful mining, a number of analyses on the stability of surrounding rocks in the LTCC face area have been extensively performed, and certain research achievements have been made. This paper introduces the main findings on rock pressure occurrence in the LTCC face during the last few decades and presents face and roof stability control techniques. INTRODUCTIONUnderground thick coal seams in China provide 1.8 billion tons of coal every year, which accounts for approximately 50% of the total Chinese annual coal production and 25% of the world, indicating that thick coal seams stand an important position in Chinese coal mining industry (Wang, 2005). Before the 1980s, thick coal seams were mined mainly by using the multiple-slice mining method. With the improvement of mining techniques and equipment in last two decades, longwall top-coal caving (LTCC) and high-seam, single-cut longwall are employed for thick coal seam extraction, offering advantages over multiple slicing from entry excavation and production perspectives (Wang, 2013).. The primary author of this paper introduced the most popular thick coal seam mining methods in China at the 30th ICGCM (Wang, 2015). This paper presents the stability of surrounding rocks in face area and ground control techniques for mining thick coal seams. For traditional longwall faces (seam height less than 3.5 m), the well-developed VoussoirVoussoir beam theory has been successfully used to analyze the movement of overlaying strata, which indicates that ground control techniques have become mature for this mining system. In such faces, the four-leg support with loading capacity of 4000–8000 kN is considered adequate for safe and successful mining. These faces normally have an annual yield of 1–2 million tons (Wang, 2007). For thick coal seams, however, the traditional support becomes inadequate and the ground control problem change to be more difficult and complex. Thus, development of large-scale mining equipment and ground control techniques for enlarged mined-out space and entries have been recognized as the most basic technical problems in mining thick coal seams."

Jan 1, 2017