Search Documents

By Joao B. Cardoso

This paper describes a two-stage reverse flotation method developed at the Mineral Resources Institute (MRII, University of Alabama, for Kerr-McGee Corporation (KMC), to separate the trona (Na2CO3 ? NaHCO3 ? 2H2O) from a saline deposit containing halite, borax, minor salts, and water insoluble materials. In the first stage, trona is depressed with Quebracho, and the insoluble gangue is floated with fatty acid. In the second stage, trona is floated with cresylic acid. The flotation concentrates contained better than 90% trona with insolubles ranging between 1 and 2%. Although the trona recoveries were low, optimization and middlings recycled in a continuous circuit could substantially increase the value.

Jan 1, 1989

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

By M. P. Corriveau

This is the case history of how two nearby plants in Southwest Virginia solved their water clarification problems. While the solutions should not be considered applicable industry-wide, the methods used in arriving at the answers deserve consideration. When Clinchfield's Moss No. 2 Preparation Plant, the first ever built in Tiller Seam coal, was started in the fall of 1956, the clays in the raw coal soon posed a flocculation problem, Laboratory sedimentation tests were initiated; and as a result, lime was adopted as the flocculant for the clays, With lime, a pH of 11.2 was required. As the plant tonnage increased, it became evident that the amount of coal fines produced in the mining and preparation was greater than had been estimated and that the 90-foot thickener was inadequate in providing sufficient settling time to effect a clarified overflow for reuse. Testing showed that Separan 26105 (NP10)1/, when used with lime, was the most satisfactory coal flocculant available,

Jan 1, 1960

By Larry Diaz

A single stage ball mill-cyclone circuit was extensively tested for its reactions to step changes in three controllable variables: feed rate, water to cyclones, and water to the ball mill. A series of carefully designed tests are to be carried out in order to determine relationships between the various ball mill and cyclone parameters. Cyclone overflow particle size distribution is to be continuously monitored during the tests using an ultrasonic device. Other circuit variables that are to be measured and recorded are feed rate, ball mill mass flow, cyclone feed and overflow densities, cyclone feed sump level, water flows, etc. Once the circuit performance is defined, two types of grinding circuit control systems will be evaluated: (a) mass flow-based; (b) particle size- based. Results obtained by each approach in terms of feed rate and cyclone overflow size distributions are discussed. The high sensitivity of continuous particle size measurements to grinding circuit disturbances is emphasized.

Jan 1, 1971

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By Bryan A. Bartley

High intensity, autogenous grinding has been developed in the hard rock, quarry industry and is finding wide application in mineral processing. The autogenous vertical shaft impactor is described and action within the machine is illustrated. This machine is compared with the cascade mill, in the three characteristics of impact, inter-particle rubbing and nipping, of which impact is the most important. There is a seven fold increase in impact level over that of the cascade mill. The autogenous impactor has characteristics of crushing and grinding, preferential crushing, abrasion resistance and drying. These are illustrated by examples of industrial applications, where the machine is now used and range from abrasives, such as Carborundum to phosphate rock.

Jan 1, 1998

By A. E. Raddatz

The U.S. Department of the Interior, Bureau of Mines, is investigating methods for recovering tungsten from domestic resources. A calcine-quench-leach (CQL) technique was developed for the extraction of tungsten from the Golconda, Nevada, hot springs ores. The deposit contains disseminated tungsten, which cannot be beneficiated by conventional techniques and must be treated by hydrometallurgical methods. The CQL procedure consists of calcining the ore at 900° C for 3 hr, quenching in a solution containing 1.5 parts of NazCO3 and 1.5 parts of NaOH per part of WO3 in the ore and at a solution- to-ore ratio of 3 to 1, leaching at 200° C and at 250 psig for 3 hr, and filtering and washing the residue. A series of closed-circuit batch tests showed that 92 pct of the tungsten was extracted from a sample containing 2.32 pct WO3. The pregnant solution contained 11 q of W03/1.

Jan 1, 1982

By A. Ligorio Pires de Carvalho

The main potash deposit at Taquari-Vassouras is contained in cycle VII, and consists of several sylvinite bodies. Cycle VII belongs to a sequence of nine cycles defined by Szatmari (1974) in the Sergipe-Alagoas basin. The sylvinite layers are separated by halite beds. They are seated on or may be laterally in discordant contact with other lithologies such as the tachyhydrites at the base, and the limestone breccia at the top. The main structural features in the deposit include numerous synclines and anticlines, salt dissolution phenomena, and open fractures associated with the axes of the anticlines.

Jan 1, 1995

By J. D. Morgan

Introduction In 1987, the US economy continued to grow steadily, reaching an annual rate of $4.6 trillion in the last quarter. The value of domestically processed mineralbased materials rose slightly to $250 billion. The value of US metals rose sharply to more than $7 billion. Industrial minerals rose slightly to $18 billion recycled scrap was valued at $4 billion. Metal prices rose sharply toward year-end. A number of mining and metal companies experienced increased profitability, fostering more optimism about the future. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and federal debt continue to rise. 244 million citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production fell 9% to 7.1 million units, but truck and bus production rose 9% to 3.8 million units. New housing starts fell 10% to 1.6 million units. Excess productive capacity exists not only in the US, but also in many other countries. Consequently, the US mineral industry is encountering stiff competition from others, as well as increasing competition from newer engi¬neered materials. Domestic production of plastics rose 9% to 25 Mt (27 million st) - on a volume basis, double all metals. Some 7% of petroleum goes to make petrochemicals including plastics. Imports of nonfuel mineral-based materials in 1987 were valued at $37 billion and exports at $24 billion. Imports supplied a significant proportion of total US consumption of several important mineral materials, including many classified as strategic and critical. In December, the Congress mandated that any major changes in stockpile goals be made only by law, and that the Department of Defense submit annually detailed stockpile supply/demand analyses. Concern about apartheid in South Africa continued, resulting in increasing interest about chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The National Critical Materials Council continued to monitor the US materials position. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve continues in effect through Sept. 30, 1989. Under the DPA, the US Bureau of Mines maintains the Emergency Minerals Administration. Further consultations were held with Canada to strengthen the North American defense industrial base. Coal production, 60% from open pits, rose 2% to 825 Mt (910 million st) valued at $21 billion. Nearly four-fifths was burned to generate 56% of US electricity. Exports included 42 Mt (51 million st) of metallurgical coal and 24 Mt (27 million st) of steam coal, with a total value of $3.3 billion. Domestic petroleum production fell 5% to 480 Mm' (3 billion bbl). Uranium mining, including recovery from phosphates, fell 4% to 5.9 kt (6500 st). Nonfuel minerals Major metals: Raw steel production - a major consumer of many minerals - rose 7% to 79 Mt (87 million st). Domestic iron ore production rose 11% to 44 Mt (48 million st), about 96% pelletized. Net imports, though, fell 8% to 11 Mt (10 million st). Raw steelmaking capacity fell 6% to 102 Mt (112 mil-

Jan 5, 1988

By Raoul Fernandez, Bernard Catalano, Guillaume Roux

The Thaumasia Joint-Venture, composed of Bouygues Travaux Publics, Soletanche- Bachy and Bessac, completed the construction of the underground section of line 2 of the Nice tramway, which comprised a 3.2 km twin track tunnel and four underground stations, in a particularly complex urban and geotechnical context. The density of the surface structures, as well as the presence of many historic buildings on its route made the construction of the tunnel even more sensitive, with a settlement threshold of Half an Inch. The joint venture faced a complex subsoil, varying from one extreme to another from highly plastic clay layers to fibrous peat and to cobbles with very high permeability, with artesian ground water, and with unforeseen anthropogenic obstacles in the tunnel section Due to the diversity of the problems encountered and their variability over short distances, the construction of the underground section of the Nice tramway, in its very sensitive urban context, undeniably constituted an unprecedented challenge.

Jun 13, 2023

By A. H. Brisse

In considering the use of a coal or a coal blend for the production of metallurgical coke, the fact is often overlooked that laboratory data can be most effectively used to determine coke plant operating conditions conducive to maximum output as well as to predict the quality of coke produced. The discussion here presented attempts to point out the manner in which carbonization data can be interpreted for industrial use and the significance of specific laboratory test results in this interpretation. The major considerable must, of course, be the safeguarded of coke oven batteries, against wall damage arising either from excessive carbonization pressures or from the wedging of the pushing ram into non-contracting coke charges. In order to be specific in the matter of handling the laboratory data involved, two series of blends are analyzed. The first of these, referred to as the "AB" series, is typical of some d' the more highly expanding Eastern- coal blends whereas the second series, here referred to as the "CD" series, is probably more typical of the Western coal blonds. Reference to Table II should be made for rank of coals considered in these blends.

Jan 1, 1959

By J. David Lowell

This paper describes the geology of the Kalamazoo copper orebody discovered in the course of an exploration project carried out by Quintana Minerals Corporation under the author's direction in an area immediately southwest of the San Manuel mine, Pinal County, Arizona. In the period 1943-1947, exploration projects were carried out in the San Manuel area by the U.S. Bureau of Mines and Magma Copper Company which resulted in the development of the San Manuel underground block-cave mine which is now in production at a rate of 41, 000 tons per day. Mining claims covering the area immediately west of the San Manuel orebody were staked in 1946 by Frank F. Salas, R. A. Buzan, H. G. Buzan, and W. C. Buzan of Mammoth, Arizona. These claims were optioned to Martha Purcell in 1946, and in the period of 1947-1958 seven churn drill holes ranging in depth from 1,400 to 2,950 feet were drilled by Mrs. Purcell. These holes did not intersect ore and no further deep exploration was attempted prior to the Quintana Minerals project which began in August, 1965, and which is described in this report. The Kalamazoo deposit is in Sections 3, 4, 9, and 10, T 9 S, R 16 E, Pinal County, Arizona, and it is reached by driving seven miles east from Oracle, Arizona (Figure 1) . The writer is indebted to Corbin J. Robertson and Ronald B. Thompson who participated in the exploration planning of this project and to a number of other individuals who contributed to its execution and management. Petrographic work by J. M. Guilbert was used as a basis for rock and alteration classifications.

Jan 1, 1968

By G. Viggiani, J. Bel, H. Wong, N. Losacco, D. Branque

"Within the framework of the European project NeTTUN, the Laboratory of Civil Engineering and Building Sciences of ENTPE in Lyon (France) is in charge of a large experimental campaign to investigate the impact of tunneling on neighbouring piled structures. For this study, an original reduced-scale (around 1:10) physical model of EPBS is used. This ""1g"" laboratory model is able to reproduce the main features of the excavation method. For this new experimental program, the miniature EPBS advances inside a large tank filled with a model soil (dry sand), in which instrumented piles were pre-installed. In this paper, the authors describe briefly the original 3D device and present results concerning the impact of tunneling on a single pile located above the tunnel. Different tunneling face pressure are studied in connection with the practice. Machine parameters, pile solicitations and stress-strain behavior of the soil mass monitored under real time conditions are discussed. INTRODUCTION When tunnels are constructed in urban areas, they often come close to pre-existing structures, such as pile foundations. Perturbations of tunnel construction on these neighbouring structures must be considered during design and construction of the tunnel. Ground movements due to tunnelling may induce bending moments, lateral and vertical loads, settlements and lateral deflections in the piles, which may lead to structural damage or failure of the piles or the supported structure. The interaction between piles and a tunnel in construction is a complex three dimensional problem. To date, several experimental approaches have been carried out to analyse the effects of tunnelling on piled foundations (Bezuijen et al., 1994, Loganathan et al., 2000, Jacobsz et al. 2004, Lee and Basset, 2006, Marshall and Mair, 2011, ). These different studies carried out in the laboratory on 1 g or centrifuged models aim at a better understanding of tunnel - piles interaction and a quantification of the influence of each dominating parameter on the structural responses. Parameters like foundation type (single pile, group of piles) and geometry, relative tunnel – pile position, volume loss induced by tunnelling, ground characteristics, pile loading history were considered. However, most of these experiments were carried out under plane strain conditions by modelling the volume loss due to tunnel excavation by decreasing the tunnel diameter or the radial support pressure. As a result, these models do not adequately account for the variations of settlements both in the longitudinal and the transverse direction, which can induce significant flexional and torsional effects on the structures. These effects are particularly critical and detrimental in the case of historical monuments."

Jan 1, 2016

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By Robert E. Ennis

Several important economic variables must be studied when planning a major underground conveyor haulage system if the objective of tow cost haulage is to be met. The purpose of this paper is to call these economic factors to the attention of the mine planner and encourage their serious consideration. To illustrate, the importance that some of these variables hole for the mine operator who wishes to reduce costs and maintain sound belt haulage practice, these areas of discussion will be covered. 1. Selection of economical flite lengths. 2. Economics of wire rope frame vs. rigid frame conveyors. 3. How idler design affects conveyor costs. 4. Economies in drive design. 5. How speed affects conveyor cost. 6. P.V.C. vs. Neoprene belt - what savings? 7. Maintaining, conveyor investment through maintenance. 8. Miscellaneous factors affecting the cost of belt haulage.

Jan 1, 1967

By P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines has been engineered, designed and operated. A non-transferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide, and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained at above 1673 K (1400 C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbon monoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pressure, and average reactor temperature. The interactions of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1993

By Alexander N. Winchell

"The iron ores of the Lake Superior region are found almost exclusively in rocks of Huronian age, the only exception of importance being in the Vermilion district. It may be estimated that about 95 per cent of the ores thus far mined have been obtained from Huronian rocks. Although these ores come from rocks of varying age and slightly varying type, they have many features in common, and therefore may readily be described together.The iron formations of the Lake Superior region consist essentially of interbanded layers of mixtures in widely varying proportions of silica and iron oxide, and are called taconite, ferruginous chert, or jaspilite. They vary considerably in hard¬ness and color, depending upon the tenor of silica and the history of the rock. Local phases of the iron bearing formation consist of cherty iron carbonates, greenalite or ferrous silicate, rocks, amphibole-magnetite masses, cherts and slates, and pyritic quartz rocks. The average iron content of all the original phases of the iron bearing formations, excluding interbedded slates, is about 25 per cent, while the average iron content for all portions of the formation, whether in the original condition or not, is about 38 per cent. It is believed that this difference is due essen¬tially to the removal of silica in solution from the. primary phases, and, of course, such removal of silica has in many cases produced material now used as iron ore, since it contains con¬siderably more than 38 per cent of iron."

Jan 1, 1920

By Clyde N. Garman

Historically, Vanadium and Uranium have been precipitated together in carbonate sill circuits. A separation of the salts of the two metals was then made on the basis of the fact that the reduced, salts of vanadium are more solo to and those of uranium lose soluble than the respective salts of higher valence. In practice this was carried out by fusing the precipitated combined concentrate with salt, sodium carbonate and sodium hydroxide with oil soaked sawdust mixed into the charge as the reducing agent. Generally the fusion was carried out batch wise and the resulting slag or glass leached in water. A good, fusion and three or four decantation washes resulted in almost complete recovery of the vanadium in the liquid phase and a very high recovery of the uranium as a dense black U02 solid.

Jan 1, 1962

By W. H. Reck

he need in the mineral industry to treat increasingly larger tonnages has caused a demand for larger installations. In order to limit the size of these installations, it was necessary to build machines with larger capacities or production output. With this aim in mind, WEMCO Division developed the No. 120 WEMCO-Fagergren Flotation Cell in 1967. These large cells have been compared to conventional smaller cells from the standpoint of metallurgical performance, investment costs, power requirements and maintenance requirements in many plants throughout the world. Figure 1 illustrates the size difference of the No. 120 when compared with the No. 66. All results to date indicate the large No. 120 cell surpasses the smaller machines in all categories.

Jan 1, 1969

By D. Hodouin

The paper reviews approaches to estimate in a real time fashion consistent mass flowrates and assays, using data from the on-stream analyzers and flowmeters of a flotation circuit. Results obtained with one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1996