Search Documents

By Wilhelm J. Kogelmann

The quest for U.S. energy independence will result in a major increase in underground mining operations. It will necessitate the rapid excavation of development drifts, entries and slopes to exploit underground deposits of energy resources such as coal, uranium and oil shale. Most of this development work will be done in soft and medium hard rock up to an unconfined compressive strength of approximately 20, 000 psi. OBSTACLES TO RAPID TUNNEL EXCAVATION Labor In the U. S. coal mining industry, the underground productivity in tons per man-day declined from 15. 61 in 1969 to 11. 00 in 1973 which is a startling 30% decline. While productivity declines, the cost of labor and supplies continues to rise. Ralph E. Bailey of Consolidation Coal Company recently stated four reasons for the decline of productivity: A shortage of experienced miners, enactment of the Federal Coal Mine Health and Safety Act effective April 1970, major changes in union work rules in 1968, and a deterioration in the attitude of the work force (1). Because there is already a great shortage of skilled miners, the situation will get worse when large new mines for oil shale, coal and uranium open in sparsely populated areas in the Western United States. Only the large scale use of easy to operate tunneling machines can increase productivity and lower the cost of excavation.

Jan 1, 1974

By B. C. Bhowmick, B. B. Dhar

Central system of ventilation, adopted almost universally in coal mines of India and elsewhere in the world, has often proved deficent in providing a cost effective solution to the acute ventilation problems of remote workings in many mines. Loss of air due to leakage through a number of stoppings, doors etc. and accumulation of heat and moisture by intake air on its way to a working through long and circuitous route are the main unavoidable reasons for low efficiency of the system, sluggish and oppressive ventilation of workings. Multi-zonal ventilation system using large diameter bore holes for feeding fresh air in the mine close to a working has been proposed as a viable economic alternative. The method promises to provide congenial environment at working faces without resorting to air conditioning or use of booster fan. Optimum location and diameter of bore holes as well as general design procedure have been dealt in the paper. Finally, the technical as well as economic advantages of the method over the conventional design have been highlighted with the help of a case study where ventilation system of an extensive shallow mine in Central India has been redesigned according to the old and the new concepts. The methodology is general enough for adoption elsewhere in other mines under similar circumstances.

Jan 1, 1993

By L. Tondo, W. Lim

The high pressure grinding rolls (HPGR) is a relatively new technology which offers the potential benefits in energy savings, circuit simplicity and improved product characteristics in minerals processing applications. Over 300 machines are now operating world-wide, but most of these are used for grinding cement clinker, and relatively few are used in conventional mineral processing. One of the rea- sons for its current limited use in the minerals processing industry is that design, scale-up and flowsheet assessment procedures are seen to be relatively immature and untested. This has reduced confidence in the potential application of the technology. To help rectify this situation an industry funded research project was undertaken, one of whose aims was to develop and prove a mathematical model of the HPGR and a scale-up procedure. Data were collected from tests using laboratory, pilot and in one case a full scale unit (2.2m diameter). A range of feed types were tested including quartz, limestone, kimberlite, bauxite, iron ore and gold ore. These data were then used to develop models of the size reduction performance, power draw, throughput and operating gap for a wide range of pressures, feed sizes, and roll speeds. This paper describes the models that have been initially developed and illustrates their accuracy using some of these data.

Jan 1, 1998

In 1991, most industrialized countries, except for Germany, were in a recession or a period of reduced growth. The US economy, already in recession, suffered from mounting banking system losses and the uncertainty brought about by the Persian Gulf War. However, US and worldwide minerals exploration did not collapse as it did during the mid-1980s. Even though gold and base metal prices declined, prices were still above cash costs for most operations. This allowed the continuation of established exploration programs but sharply limited new initiatives. Exploration 1990-1991 Planned worldwide 1991 exploration expenditures declined by about 8% from 1990 levels, according to a survey of 153 companies by the Metals Economic Group (MEG). Canada was the leading exploration target with 23% of the total, followed by Australia and the US (19% each), South Africa (13%), Latin America (11%) and the South Pacific (7%). The remaining 8% was split evenly between Europe and the rest of Africa. In Latin America, Mexico and Chile are the most attractive countries for exploration. Recognizing the risks involved, the industry has been cautious about ventures in the former Soviet Union. Survey results also showed that while the majors expected to maintain exploration spending, smaller firms were cutting back or actively seeking farm-outs from the majors (personal communication, M. Wegener, MEG).

Jan 1, 1992

By J. A. Wallace

U. S. Steel's coal mining research activities are directed toward providing new or improved hardware and techniques to increase productivity or reduce cost. Because more than 80 percent of U. S. Steel's coal production is obtained from continuous miner sections, most of our research efforts are focused upon that mining system. Current and historical time study data show that our continuous miners only operate about 30 percent of the available face time. This limited equipment utilization is the result of the delays or interferences imposed by the non-coal-cutting phases of the continuous mining cycle. The most time consuming of these delays are: waiting-on-roof-support, tramming between alternate work locations, waiting-on-haulage-capacity, and in some mines waiting for excessive methane concentrations to clear. Because waiting on roof support is our most time consuming delay, several programs are underway simultaneously to address this problem. In one of these we are developing a patented microprocessor-based control method and apparatus to improve roof drilling performance. This increase is attained by using the microprocessor to adjust electrohydraulic valves which control drill thrust and rotation speed. The microprocessor is designed to continuously search for an optimum combination of thrust and drill rpm to maximize penetration rate at all times.

Jan 1, 1979

By Adolf U. Honkala

Dundee Cement Company was incorporated in 1958. The equity capital for the venture was supplied by a Swiss firm called Holderbank Financier and a group of its principals. Holderbank Financier, a holding company, is a direct outgrowth of Holderbank Cement Company, a company founded in 1912 by the father of Dr Hans Gygi who is the president of Dundee Cement Company and a member of the Board of Holderbank Financier. From one plant in 1912 located in Zurich, Switzerland, Holderbank grew to its present size of 32 plants in 17 countries, having a capacity of 90 million barrels of cement per year. Dundee Cement Company constructed its first cement plant near the little town of Dundee, Michigan. This site was selected because there is an abundance of limestone and clay of the correct chemical composition for cement manufacture and the deposit was advantageously located near the large population centers of Detroit, Toledo, Cleveland, and Chicago. Construction of the 5. 5 million barrel, two kiln, plant was completed and the plant started up in the fall of 1959. After a year or two of the usual problems in a new plant and the expected difficulty of breaking into a nearly saturated market, Dundee began to prosper.

Jan 1, 1970

By Anthony Edey

It is a generally accepted and widely discussed fact that the world in general, and the United States in particular, face a shortage of energy at the present time which will become worse in the future. There is, however, no sign of a similar concensus as to the actions which would prevent or overcome this expected shortage. An immense variety of solutions has, however, been put forward, ranging from the purely political to the outer fringes of sophisticated technology. One resource which surprisingly is often only cursorily included in this discussion is the immense known petroleum reserve lying within the United States. When this subject is discussed, indeed, it is usually in the context of the improvements in production or new discovery rate that could be expected to result from possible politico-economic actions that would raise the real price obtained for domestic crude. This interest in the potential for improved domestic production is undoubtedly justified, but very little attention is normally drawn to the fact that even under the most favorable policy framework the majority of the oil that has been, or will be, discovered will remain in the ground due to the inherent limitations of production through surface wells.

Jan 1, 1979

By C. Einberger

Groundwater Monitoring is typically required by regulatory agencies at potentially hazardous landfills or surface impoundments. Agencies have often required an arbitrary number of wells with limited evaluation of the effectiveness of the network to detect a leak. A Monitoring Efficiency Model (MEMO) has been developed to improve the design and cost effectiveness of monitoring well networks. MEMO 15 an analytical model that simulates the migration of hypothetical contaminant plumes from a site and quantifies the efficiency of alternative well network designs in detecting the plumes. The computed monitoring efficiency provides a quantitative measure of the well network adequacy based on hydrogeologic considerations. The model was recently used to design the groundwater monitoring well network for a heap leach pad at the proposed Beartrack Project.

Jan 1, 1993

By C. A. Fleming, C. J. Ferron, E. S. Makande, P. Mason

Several small mines are producing refractory gold concentrates in Zimbabwe and, owing to the small scale of most of these operations, their output is processed in a central custom roaster in Kwekwe. Owing to the wide variations in the feed to the roaster, the efficiency of the old Edwards roaster is deemed unsatisfactory with gold recovery from concentrate as low as 70%, and alternative processes were evaluated to improve this situation. Various processes for oxidizing refractory arsenopyrite/pyrite concentrates to liberate gold prior to cyanidation are known. In practice, only two have to date met with wide industrial acceptance, pressure oxidation and roasting. Owing to the ·high arsenic and antimony levels of some concentrates in Zimbabwe, the only viable roasting alternative would be two-stage air-roasting of concentrates in two reactors, as practiced at Giant Yellowknife, Campbell Red Lake and New Consort. This process, however, creates an arsenic disposal problem, and produces gas of fairly low SO2 content, requiring a large gas handling system for acid production. On the other hand, there are currently four commercial pressure oxidation plants treating refractory gold ores (McLaughlin, Mercur, Getchell and Goldstrike) and three treating concentrates (Sao Bento, Porgera, Campbell). One other concentrate oxidation plant is being constructed (Con), and several more are being considered.

Jan 1, 1992

By Samantha Smith

Nautilus is completing the world's first environmental impact assessment (EIA) of seafloor mineral extraction and Nautilus has gained extensive experience conducting environmental studies in subsea environments. Nautilus is currently working on the Solwara 1 Project in the Bismarck Sea, Papua New Guinea, where high grade seafloor massive sulfide deposits lie at ~1600 m water depth. Conducting an EIA in the deep sea presents some interesting and exciting challenges. Seafloor studies commenced in December 2005 using a remotely operated vehicle (ROV) fitted out with highly specialized scientific equipment to conduct water quality, sediment, biological and oceanographic studies. During 2007 and 2008, Nautilus launched two two 30-day ROV programs dedicated to environmental baseline studies and during this campaign, over 550 biological, sediment and water samples were collected and over 20,000 seafloor observations were logged. On board specialists included an international team of experts in the field of deep sea marine science. Collaboration between industry and scientific research institutions allows data to be collected for the EIA but also provides an extraordinary opportunity for researchers to access sites that might otherwise remain unobtainable to science. This presentation will review the studies conducted as part of this exciting project. Keywords: Seafloor Massive Sulfides, Environmental Impact Assessment

Jan 1, 2008

By P. T. Brown

Denison Mines Limited, Canada's largest uranium producer located in Northern Ontario recently embarked upon an extensive development program that would allow them to substantially increase production and also meet the more stringent air quality standards established by the ministry of Natural Resources. To proceed with this program it was essential that the fresh air supply be greatly increased to the underground workings. A major portion of the mining area is located under Quirke Lake on the north limb of a syncline termed the Quirke Lake trough. The Denison engineers determined the most practical size and location for a proposed new fresh air shaft, eventually deciding to drive a 25 foot diameter shaft, 490 square feet in section for 1,800 feet long vertically. The shaft collar would be located on Roman Island, an island in Quirke Lake. A test hole was drilled from Roman Island to determine the ground through which the ventilation shaft would pass. This drill hole confirmed the location of the Quirke Lake over-thrust fault, a highly fractured water bearing zone 165 feet thick, approximately 800 feet below surface. Plans were made by Denison Mines Limited to seal and consolidate this ground when it was encountered by the shaft.

Jan 1, 1974

By Haydn H. Murray

The three major catalyst markets that utilize industrial minerals as raw materials are petroleum refining, chemical processing, and emission control. Because of economic, competitive, and regulatory pressures, catalyst producers are pushed to develop products with improved performance to meet changing environmental standards. Also, refiners are demanding new families of cracking catalysts that will crack residual fuels. In 1987, worldwide cracking catalyst sales amounted to $457 million (Occelli, 1988a). Recently enacted federal and state laws to improve air quality have prompted strong growth for environmental catalysts, which in 1989 accounted for more than a third of the $1.9 billion catalyst market in the United States (Farrauto, Heck, and Speronello, 1992). A catalyst is a material that promotes or enhances a chemical reaction but does not itself enter into the reaction. One of the more important mineral groups used as catalysts is clays. The first recorded use of clay as a catalyst was its use in the dehydration of alcohol (Bondt et al., 1797). Clay minerals that are used as catalysts are kaolinite, halloysite, smectite, palygorskite, and sepiolite. Minerals used as catalysts, catalyst supports, or as a raw material to make zeolites are kaolinite, halloysite, sodium montmorillonite, calcium montmorillonite, hectorite, palygorskite, sepiolite, talc, calcined kaolinite, gibbsite, chlorite, and titanium dioxide.

Jan 1, 1994

By Reinhard Gnilsen

Ground pillar control in soil and weak rock often represents a critical and sometimes a determining factor for mined underground civil structures. A concept is desirable that minimizes the restrictions possibly imposed by pillar control requirements on geometrical tunnel characteristics and on the mining operation itself. Conventional concepts are discussed and an alternative concept is introduced. This concept reduces pillar control requirements to ground control measures required with "regular" tunnels. The conventional model of pillar mechanics with potential yielding of a ground body in more than one direction, is then avoided. Due to the complexity of pillar mechanics, the level of engineered design furnished to the contractor is crucial to optimizing ground pillar control. Conventional versus alternative contractual arrangements for pillar control are described and their important role is illustrated. The concept introduced relates to principles inherent to the New Austrian Tunneling Method (NATM). However, tunnel projects using other mining concepts can employ alternative ground pillar control principles as well, if certain criteria are observed. Case histories in the United States and abroad are presented and the impacts from different concepts of ground pillar control are illustrated. The paper concludes by analyzing concept characteristics that can infer monetary impacts on both the owner and the contractor.

Jan 1, 1987

By G. R. Tostengard

Gold plant performance during the start-up period, which extends until capacity production is sustained, has a major impact on the internal rate of return and the net present value of gold projects regardless of mining and processing configurations. The start-up period experiences substandard production, extra expenses, and sometimes reduced recovery. This results in lost profits, a portion of which are recouped at the end of the life of the mine. Poor start-up performance can put projects into financial jeopardy. The gold mining industry regularly experiences start-ups ranging from good to poor. Problem areas, which affect start-up performance, include shortcomings in ore reserve sampling and testing, equipment design and installation, untrained plant operators, inability to cope with problems which arise, and organization of the maintenance program. An investment, equal to 0.5% to 1.0% of plant capital cost, in programs to prepare for start-up, in advance, is recommended. Investment in such a program will make a good start-up possible. Without it the best result which can normally be expected is a fair start-up. Developers of new gold mines are urged to compare the cost of this investment with the anticipated increase in project net present value. Funds for this investment should be included in feasibility studies.

Jan 1, 1988

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

By Michel Claisse, R. P. Goel, André J. Rancourt, Kent Murphy

The Malana Hydroelectric Project is a private development located in HimachalPradesh State, India that was commissioned in June 2001. The plant was built and is owned by the Malana Power Company, a subsidiary of the Bhilwara Group of New Delhi. With a total head of 400 m and nominal capacity of 86 MW, the plant is capable of generating 360 GWh annually. The 3,1 km long, 4,0 m diameter power tunnel was designed to be excavated by conventional drill and blast methods. Contrary to traditional practice in India for pressure tunnels of providing a concrete lining, the Malana tunnel was finished mainly with shotcrete. In this way, the tunnel was completed in a period of18 months, a record for recent projects in the Himalayas, and at a cost substantially below that of conventionally lined tunnels. An interesting aspect of the project was the design of the steel tunnel liner linking the power tunnel to the penstock. The length of the liner was fixed finally on the basis of in-situ testing using both hydraulic jacking and doorstopper tests to evaluate the ability of the rock to withstand the internal pressure of4,0 MPa that exist near the downstream end of the tunnel.

Jan 1, 2003

By K. T. Dreher, J. A. Brierley, C. L. Brierley

Water from underground uranium mines located in the Ambrosia Lake district near Grants, New Mexico, U.S.A., is treated to reduce levels of uranium, selenium, radium and molybdenum. The treatment system consists of a series of ponds and an ion exchange plant. Bacterial and algal populations present in the pond system are considered agents which actively assist in removal of the pollutants present in the water. Pondbottom sediments maintain a reducing zone and a large population of sulfate-reducing bacteria of the genera [Desulfovibrio] and [Desulfotomaculum]. Uranium, molybdenum, and selenium accumulate in the pond sediment. Stimulation of the microbial sulfate-reducing activity resulted in a decrease of soluble concentrations of these elements in laboratory systems. Predominant components of the treatment ponds’ algal flora are the filamentous [Spirogyra] and benthic [Chara]. Laboratory study indicates that [Spirogyra] is more active than [Chara] in removal of uranium and molybdenum from solution. However field-collected algal samples of both of the genera contain uranium and molybdenum. Laboratory studies indicate that death and decay of the algae in association with pond sediment does not result in return of cellbound uranium and molybdenum to the water. The algae appear to act as bio-filters for accumulation of particulate pollutants and agents for adsorption and/or absorption of soluble pollutants.

Jan 1, 1980

By Randal J. Barnes

There are many methods available for the estimation of geologic parameters (Popoff, 1966; Barnes, 1980). In the last decade a new and relatively sophisticated technique using statistical theory has emerged: geostatistical kriging (David, 1977; Journal and Huijbregts, 1978; Rendu, 1978). An interesting property of geostatistical estimation is that when a geologic parameter is estimated for a given volume, not only is the estimate generated but an associated measure of certainty is produced as well. This statistical measure of estimation confidence is called the estimation variance. While the concept of an estimation variance is universally considered to be a good idea, mining engineers and geologists do not currently have the tools to incorporate it into their planning and quantitative analysis. This paper attempts to develop and present some of the necessary tools required to incorporate estimation uncertainty into mine planning. Geologic uncertainty is portrayed as an economic business risk. This risk is objectively characterized, and-the associated cost is quantified. Geologic delineation sampling is viewed in this light as an economic commodity with an associated cost and value. A coal mine planning example is used as a focus in this presentation. The data used is real, though it has been modified to maintain data security and project anonymity.

Jan 1, 1986

By Victor S. Sazhin, Alexander Kostenko

The hydrochemical method, which is based on the separation of aluminium oxide and silicon oxide by the hydrothermal decomposition of aluminosilicates by alkaline solutions in the presence of calcium oxide, can be effectively used for the complex processing of high-silicon aluminium ores. In this case, the silica is bound to a slightly soluble compound: Na20.2Ca0.2Si02•H20 (under the conditions: [&k]= 9, CaO/SiO2 = 1.05, alkali concentration in the solution: over 300 g/l Na20, T = 240...300 °C). If alkaline solutions of 100...150 g/l Na20 concentration are used, Ca0•SiO2•H20 or 2Ca0•Si02.0.5H20 compounds, depending on calcium oxide dosage, are formed at 280...320 °C. New methods for the crystallization of Na20.Al203.2.5H2O from concentrated alkaline solutions rand low-concentration solutions are proposed to isolate aluminium from solutions. The hydrochemical method, which involves no sintering process allows one to decrease the expenditure of heat by a factor of two, to reduce the investment and to exclude the pollution of the ambient air by dust-laden gases. The expansion of the raw-material resources base of

Jan 1, 1984