Search Documents

By C. H. Rawlins

Deep bed media filtration is used as a tertiary treatment step (after hydrocyclones and flotation cells) to remove fine oil droplets and solids from oilfield water before reinjection disposal or to remove particulate material from surface waters used for waterflood injection. Oil and solids injection requirements are typically <5 ppm concentration at <2 micron diameter. The preferred media for produced water filtration is walnut or pecan shell, however the use of this media has evolved by trial & error and the fundamental mechanisms that occur during separation and media cleaning have not been investigated. A project was initiated to fill in this knowledge gap by analyzing the physical, mechanical, chemical, and hydrodynamic properties of six types of granular filtration media (12/20 mesh size): garnet, silica, anthracite, pecan shell, English walnut shell, and black walnut shell. Comparison of bed packing, oil wetting, attrition resistance, particle strength, and fluidization has led to an understanding of the preferred filtration media for separation of fine oil droplets and solids.

Jan 1, 2010

By Pierre Mousset-Jones, Felipe Calizaya

The design of an auxiliary ventilation system for long underground openings (drifts, ramps and shafts), often requires the installation of multiple fans. The fans are installed in series and separated from each other by rigid ducts of fixed or variable length. However, problems relating to excessive leakage often occur, with each project representing a unique problem requiring an efficient solution. In this study, a method to determine the design parameters of an auxiliary ventilation system is presented. The method is based on the principle of partitioning a long ductwork into segments of finite length and solving the resulting networks separately. Specifically, the method is developed to solve two types of problems: constant fan spacing, and constant fan size. In the former, the fan spacing is fixed, and the problem is solved for fan sizes. In the latter, the problem is to solve for fan spacing. An example is used to illustrate the method.

Jan 1, 1993

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By Anthony Harding, Rodolfo D. Aradas, Juan M. Fernandez, Darío Tsingas

"The adoption of tunneled combined sewerage interceptors and outfalls leads to design linings which are often subject to internal pressures that are larger than the external pressures, resulting in significant tension loads. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining. However, improvements in concrete technology and the need to seek efficiency in terms of time and costs, have driven designers to consider single pass segmental linings. The Riachuelo Sanitation project in Buenos Aires is subject to these constraints both upstream and downstream of a sewage treatment plant. This paper describes how the challenges of up to 2 bar pressure differential have been addressed by careful analysis of soil structure interaction to ensure that the full benefit of external ground pressure is realized, resulting in a more optimal design for the constructor both in terms of cost and time. INTRODUCTION The construction of long sewerage interceptors and outfalls is becoming an increasingly common piece of infrastructure for modern urban cities facing a large water front and estuarine conditions, which are under a significant environmental burden imposed by decades of sustained growth. Such works intercept most of the distributed sewage discharges to then divert them to a central treatment point from which it will be finally diffused via an outfall into a water body capable to accept these discharges under acceptable environmental conditions. Depending on the magnitude of the sewage load to be handled, the configuration of the urban environment and the conditions of the receiving water body, both in terms of oceanography forces and seabed conditions, these schemes will vary in length, conveyance capacity and design and construction requirements. When conditions permit, the current trend is the execution of long outfalls using flexible solutions (such as the use of HDPE pipes) which usually require some form of concrete ballasted weights to resist off shore dynamic forces when directly laid over the sea bed. However, this concept faces limitations when the conveyance requirements indicate the need for large diameters (typically above 3000 m) and also when the outfall needs to avoid deep features off shore such as navigation channels. When this occurs, tunneling, particularly segmentally lined tunnel constructed by TBM emerges as the most feasible approach for large diameter, long deep outfalls. The operating conditions often result in internal pressures that are larger than the external pressures, resulting in significant tension loads in the lining. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining."

Jan 1, 2016

By Edward J. Zeigler, John T. Miller

INTRODUCTION Construction of Phase I, Section A, of the Baltimore Region Rapid Transit System required that six underground stations be built using a cut and cover excavation technique. For five of these stations, soldier piles, used as support of excavation, were installed with tip elevations well below the bottom of the excavation. However, in the case of the sixth subway station, the Mondawmin Station, soldier piles were installed only through soil and decomposed rock, with the tips of the piles being stopped well above the bottom of the excavation in partially decomposed rock. Below the tips of the soldier piles, and below a cut slope where piles were not installed, the sides of the excavation consisted of partially weathered and fresh rock and were supported by a combination of rock bolts, wire mesh and shotcrete. An extensive installation of geotechnical instrumentation permitted detailed monitoring of horizontal and vertical movements of the soldier piles and the walls of the excavation. Preliminary studies indicated that the excavation support system selected for the Mondawmin Station would have several advantages over a conventional system consisting of soldier piles extending to the bottom of the excavation, braced with prestressed struts. These advantages included lower cost of installation, a decreased time required for installation, and a more open excavation for the contractor during construction of the station. The Mondawmin Station is situated in the northwestern quadrant of Baltimore City, approximately 6.4 km (4 miles) from the center of the City. The station lies midway in a project 12.9 km (8 miles) long identified as Phase I, Section A, of the Baltimore Region Rapid Transit

Jan 1, 1981

By S. K. Kawatra, S. Valluri

With increased CO2 emissions from steel and coal industry, there is great opportunity to capture CO2 and utilize the captured CO2 for economic advantage. The primary goal is to develop energy-efficient processes that reductively couple CO2, an abundant and renewable carbon source, for the production of value-added chemicals such as methanol, ethanol, and oxalic acid. These chemicals can be used elsewhere in the refining process or sold as valuable by-products. Geological sequestration, in comparison, has no economic return. Current CO2 utilization research at Michigan Technological University focuses on electrochemical reduction of CO2. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. This paper will present different ideas and their viability to utilize CO2 as a feedstock to produce several value-added compounds. INTRODUCTION Carbon dioxide (CO2) emissions into the atmosphere will need to be drastically reduced to curb the various undesirable effects of climate change. The large contribution in total CO2 emission originates from coal or natural gas power plants, and a considerable amount from steel plants. Average CO2 emissions in the US from steel industry is 2.9t CO2/t steel (Global CCS Institute 2013). Capturing the available CO2 from the steel and coal industries for economic advantage is a win-win situation for the industry. This technology is not only important scientifically but is also vital for a sustainable future. The various ongoing investigations can be categorized as biochemical, thermochemical, photochemical, and electrochemical approaches. Among these, the electrochemical method shows the most promise as an efficient form of CO2 conversion technology, because of its many advantages like high reactivity under ambient conditions and good extensibility from small- to large-scale processes1 BACKGROUND Extensive research has been done on the chemistry of transforming carbon dioxide into more useful products. Methods are known to convert carbon dioxide into a wide variety of substances, including methanol, isobutanol, carbohydrates, methane, carbonates, urea, formic acid, oxalic acid, carbon monoxide, epoxides, formaldehyde, and so on. Several of these (carbohydrates, formaldehyde, isobutanol etc.) are primarily results from biological processes. The rest are results of strong reduction reactions or electrolytic reduction. In short, electrolytic reduction can be used to form methane, methanol, formic acid, oxalic acid, carbon monoxide from carbon dioxide2. CO2 reduces at the cathode in an electrolysis cell. These processes have the general form of generating the carbon dioxide anion radical (2⋅−) and allowing it to react with itself or the electrolyte3. Catalysts can be added to influence the formation of the anion radical or to suppress side reactions3. The electrolyte, catalyst, voltage, electrode material and CO2 content are all known to effect the reaction pathway. Table 1 shows the overall reactions and energy requirements for electrochemical conversion of CO2 to chemicals

Jan 1, 2019

By John T. McDonough

The Climax Mine of AMAX&apos;s Climax Molybdenum Division is currently producing approximately 34,000 tons of molybdenum ore per day from two underground levels (see Figure I), and initial design is underway for the next deeper (1200) level. The aim of this report is to present the methods of site evaluation used at Climax for cavability determinations and underground support design. Climax succeeds with its panel caving system of mining (Julin, 1973) (Figure 2) largely because of the presence of pervasive geologic structural discontinuities. The stockwork ore body at Climax was formed by the multiple intrusion of mid-Tertiary rhyolitic magmas into Precambrian granite, schist and gneiss, and the hydrothermal emplacement of molybdenite into the network of fractures that were generated during the forceful upward intrusion of magma. Subsequently, intrusive events that were more deeply seated refractured the overlying, ore- bearing stock and propagated a complex system of axial and radial fractures. Post-ore movement along the Mosquito Fault (Wallace, 1968) and its associated stranded shear zones further fractured the ore body and disordered the existent geologic structure. The result of these structural events is a brittle, crystalline ore body that is transected by a complex pattern of faults, shear zones, and joints that augment cave initiation and enhance comminution of the ore blocks. Generalizations can be made about the structural trends within the ore deposit (King, 1946; Kendorski, 1973), however, the intensity and orientation of geologic structure is by no means uniform throughout the ore body. The relative intensities of silicic and argillic alteration are also highly variable (Vanderwilt and King, 1955). As a consequence, no single rock-mass model suffices as a standard for mine design, and site characterization for cavability and support design is a continuous process.

Jan 1, 1977

By Marie-Antoinette Dziurla, Barrie Johnson, Åsa Kolmert

Acidophilic bacteria are well known for their role in accelerating the oxidative dissolution of sulfide minds, such as pyrite. Other acidophiles, however, are able to catalyze dissimilatory reductive reactions. Bacteria that reduce ferric iron to ferrous, and sulfate to sulfide, were isolated from ARD-impacted environments and immobilised onto porous beads made of recycled glass. Column bioreactors containing colonized beads were constructed and peacolated with synthetic and actual ARD, and evaluated for their capacities to promote iron or sulfate reduction, and pH amelioration. Iron reduction did not require strictly anoxic conditions in bioreactors, and rates of up to 800 mg Fe3+ reduced/(l*day) were achieved, with a conversion efficiency of up to 98%. Using mixed populations of acidophilic fungi and iron-reducing bacteria, the bioreactors were capable of promoting iron reduction using paper pulp as sole carbon and energy source. Reduction of sulfate in pack bed bioreactors was observed with acidic wastewaters of pH 3 and above, though average rates of 300 mg sulfate reduced/(l*/day) were less than those recorded for circum-neutral pH systems. Bioremediation of ferric iron-rich ARD was assessed using coupled iron-reducing and sulfate reducing bioreactors.

Jan 1, 2000

By K. S. Eric Forssberg, Lennart Ryk

The paper discusses coal utilisation in Sweden. All hard coals have to be imported from other countries. Peat from domestic sources is used as a complement. Environmental legislation and taxation on fuel and emissions are severe. This situation affects the procurement, preparation, handling and use of coal. The paper presents: • R&D projects concerning deep cleaning of thermal coal. • Handling and treatment of coal used in PFBC boilers and for blast furnace injection • Dust prevention for coal and peat briquettes. Procurement of coal emphasising quality and environmental issues.

Jan 1, 1995

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

By M. Tokoglu

Accurate estimation of resources is one of the major challenges in mineral project evaluation. Contemporary mineral resource estimation practice calls for contribution from several disciplines and execution of several interdependent tasks. 3D estimation domain modelling is obviously one of the most essential components of such a substantial process which forms the basis of this research. The study constitutes a comparative analysis of four major domain modelling techniques; (i) explicit modelling, (ii) implicit modelling, (iii) indicator kriging, and (iv) conditional simulation. It involves comparison of outcomes for alternative scenarios to assess the implications of the modelling decision on resource estimates of a polymetallic massive sulfide deposit located in western Turkey. Thus, identical grade estimation method and parameters are considered to identify the discrepancies arising only from the choice of the domain modelling approach and underlying assumptions. Economic implications are demonstrated in the form of range of outcomes for the extends of the ultimate pit, ore tonnages (min:37.0 Mt, max: 46.7Mt), waste tonnages (min:201.2 Mt, max: 251.2 Mt), stripping ratios (min:5.18, max: 5.71), and total pit values (min: $1.05B, max: $1.45B). Examination of solid models as well as cross-sections revealed that major discrepancies are observed beyond outlying drillholes. Therefore, it has been proposed that assumptions regarding extrapolation distance is the main source of mentioned dissimilarities. Key words: Domain modelling, explicit modelling, implicit modelling, indicator kriging, conditional simulation INTRODUCTION Resource estimation is apparently a challenging process calling for extensive expertise and input from several sources, each of which introducing its related uncertainties. In the last decades, substantial role of quantitative analysis of several forms of risk and uncertainty in evaluating projects’ upside potential and downside risks has been realized. Studies indicated that mining companies have been severely impacted because of not meeting project expectations. As noted by Vallee (2000) “… in the first year of operation after start-up, 60% of mines surveyed had an average rate of production less than 70% of designed capacity”. Several other studies on mining projects also revealed that uncertainties related with the resource model are one of the major contributors of mentioned shortfalls. In this perspective, quantification of uncertainties associated with each component of estimation process is critical. 3D estimation domain models capturing major mineralization controls are the fundamental components of contemporary mineral resource estimation. Domain models are key guiding tools for estimation and are products of a complex process involving many unknowns and assumptions. There exists a number of 3D modelling alternatives which are distinct with respect to complexity, time and effort involved. Acknowledging potential influences on downstream mining practices and relavent economic implications, risks and uncertainties associated with 3D domain modelling are critical yet poorly studied aspects.

Jan 1, 2019

By D. H. Davidson

In situ leaching (ISL) of copper has the potential of reducing both capital and operating costs for copper production. The ISL process combines surface facility (SX/EW) and wellfield operations, each of which must process the same total flow rate and pregnant liquor copper concentration. Commercial cost data are only available for SX/EW facilities. This paper discusses: the interaction between the principal wellfield costs associated with well modules, and wellfield start?up with SX/EW costs; how to estimate what the level of wellfield costs must be to optimize DCF/ROR; and how to relate these wellfield costs to orebody geologic and mineralogic characteristics.

Jan 1, 1988

By F. Djahanguiri

The US Bureau of Mines con¬ducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1997

By J. A. Herbst, S. L. Blust

Optimization of blasting, crushing, and grinding operations is filled with challenges. One of the more difficult tasks is accurately sampling and determining the size distributions of blasted and crushed materials at a reasonable cost. The task is difficult because of the large size of fragments and the tonnage involved. However, the size distribution measurements are necessary for models that predict the performance of mine-through-mill operations. This paper is concerned with the use of video sampling for this task at National Steel Pellet Company&apos;s operation in Keewatin, Minnesota Data gathering, data analysis, model building, and mine-to-mill simulation are all described.

Jan 1, 2000

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high-expansion foam generator. Thus allows fire fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600 ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

Jan 1, 1996

By Ning Liu, Di Yin, Xuming Wang, Yongqiang Lu, Jan D. Miller

Air-sparged hydrocyclone (ASH) flotation technology has been evaluated for phosphate recovery from the central Florida phosphate deposits. As expected, it was demonstrated in pilot-plant tests that the ASH system has a specific capacity about 50-100 times higher than that of a traditional flotation cell. In the case of fatty acid flotation, single-stage ASH flotation produced a recovery of 75-77% in a rougher concentrate containing 24% P2O5 In reverse flotation with amine, the single- stage ASH system produced a phosphate recovery of 98% in a cleaner concentrate containing 31% P2O5. These results are comparable with those obtained at plant operations in the Florida phosphate industry. Based on these pilot-plant results, the effects of process variables are discussed in terms of separation efficiency. Subsequently, a 6-inch ASH system was fabricated and tested in a central Florida phosphate plant for reverse flotation in the amine flotation circuit. The high capacity of the ASH system was again demonstrated for the 6-inch ASH system. A single-stage phosphate recovery of 91% was achieved with a concentrate grade of 30% P205. During plant tests, it was established that porous tube plugging, the most significant engineering problem identified, was due to the poor quality of the plant water. Possible solutions to this problem are discussed.

Jan 1, 1999

By Barry R. Doyle, Ilsley Roger C., John Ramage

It was anticipated that settlement would occur when tunnels were excavated in weak organic soils with high groundwater levels in downtown Milwaukee. Because of the potential for damage to adjacent buildings, an approach was devised during the design to address this issue. In order to do so effectively, estimates of settlement trough geometry were made; buildings identified which were potentially at risk; the means of settlement measurement designed; and threshold limits of settlement and courses of action specified. Bid items were provided for underpinning the critical structures. The approach addresses the design issues and delineates the sharing of risk between the owner and contractor. The predicted and actual performance experienced are also discussed.

Jan 1, 1989

By B. Govindarajan, L. S. Rao, T. C. Rao, B. R. Rao

Laboratory leaching experiments were conducted to extract potassium from glauconitic sandstone, and the effects of important variables were studied. The reduced time plot (RTP) for all of the variables obtained from the experimental data has been quantified by this simple equation: R = 100 (1 - exp (-0.693 *(T/T50)0.605) The time required for 50% extraction (T50) has been correlated by a regression equation to variables such as acid strength, temperature, fluorite: glauconite ratio and % solids. Both of these equations were used to predict the extraction percentage at different process-variable levels. In addition, several other experiments were conducted at arbitrary levels of the variables to verify the equations developed.

Jan 1, 1994

By Roshan B. Bhappu, Sukhendu L. Barua

The economics of developing and operating small precious metal mines are unique and require much more scrutiny than larger mines since a limited tonnage must carry a heavy burden of capital investment as well as operating cost per unit ton to be mined and processed. Moreover, potential operators of small mines do not have the required expertise available to critically evaluate the technical and economic aspects of their projects. In this paper, the authors have attempted to provide technical and economic guidelines for developing and operating small precious metal mines. Capital and operating cost estimates as well as return on investment are provided for various scenarios utilizing different mining and processing techniques.

Jan 1, 1987