Search Documents

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By Peter Halbach

Cobalt-rich ferromanganese crusts are one type of the two oxidic metallic mineral resources in the deep ocean that incorporate metals supplied and transported from both land (aerosols, continental run-off) and sea sources (oxygen-minimum zone, hydrothermal alteration of the oceanic crust). The substances directly precipitate from cold seawater under more or less oxic conditions and form thin layers (2 up to 25 cm thick) on hard substrate rocks like volcanic hyaloclastites, weathered basaltic rocks and/or carbonate-fluorapatite; in the crusts many metals therefore exist in the highest state of oxidation. Deposits of the Co-rich ferromanganese crusts are found throughout the global oceans on the flanks, terraces and summits of seamounts and submerged volcanic mountain ranges and platforms, where the ocean currents have kept the seafloor more or less free of sediment for millions of years. The process of hydrogenetic precipitation is basically an inorganic colloidal-chemical and surface-chemical mechanism. Elements in seawater may occur as dissolved hydrated ions or as inorganic as well as organic complexes which in general have either a positive or a negative surface charge depending on the pH of the respective aqueous environment. Those complexes may form hydrated colloids that interact with each other and with other dissolved hydrous metal ions. Hydrated cations such as Co, Ni, Zn, Sn are, for example, attracted by the negatively charged surfaces of colloidal hydrous Mn-oxide particles, whereas hydrated anions (e.g. oxyanions) and elements forming larger complexes with low-charge densities (e.g. U, As, Th, Hf, REE) are attracted by the slightly positively charged hydrous Fe oxihydroxide particles.

Jan 1, 2008

By E. B. Jensen

The results of an extensive one- year test period of a nonelectric explosives detonating system led to the mine-wide adoption of this system at the Henderson Mine in early 1978. Since that time, extensive experience with nonelectric initiation has verified the earlier results which include the following benefits: 1. Increased blasting safety 2. Improved productivity 3. Cost effectiveness 4. High reliability At the present time, while electric blasting caps still experience a limited use restricted to trunkline initiation, all heading rounds as well as the longhole bell, undercut, boundary cutoff and raise blasting are detonated non-electrically. The primary blasting agent used is AN/FO, and primers are typically one of the following products (depending on application): PETN, semi-gelatin dynamites or a nonnitroglycerin water-gel slurry.

Jan 1, 1982

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

By J. W. Currier

The compositions and natures of the materials charged to a blast furnace, as well as their respective distributions within the furnace, are known to int1uence furnace performance. However, fifteen years ago, there was little reason to believe that any significant variation of these parameters had been overlooked. Nor was there any particular reason to believe that olivine might be a particularly useful raw material for blast furnace applications.

Jan 1, 1989

By S. Bhamidipati

Abstract. Controlled flow is an aspect often desired in mine ventilation. This is normally obtained by using fans and regulators to achieve the required pressure balance in the system. Preference for a certain network layout of these control devices is influenced by technical as well as legal and economic factors. In this study, a model is developed based on an economic criterion by which an optimum layout of fans and regulators for a controlled flow system can be determined. The concept is analo¬gous to the critical path crashing. However, a linear programming package is used to demonstrate the solution procedure for a hypothetical venti¬lation network.

Jan 1, 1983

By A. G. Provost

On April 3, 1981, Harrison Western Corporation was awarded a contract by Amax Alloy - A Division of Amax Inc., to sink the Henderson #5 ventilation shaft. The project was located on the Henderson Mine site 88 kilometers west of Denver near the town of Empire, Colorado (Figure I). The Henderson No. 5 Shaft, located in an Alpine environment at an elevation of 3145 meters, was a 9.8 meter diameter concrete lined shaft with a total depth of 793 meters. Work started and continued with Harrison Western employees until January 15, 1982. At that time, Amax made the decision to continue the shaft-sinking with their own labor, and with Harrison Western providing supervision under a management service contract. Shaft sinking continued under this arrangement to October 1, 1982, at which time Amax put the Henderson No. 5 project on standby status until further notice.

Jan 1, 1986

By W. E. Horst

Historically, research organizations have made significant contributions to the development and commercialization of new chemical products for the mining industry and examples of commercial results are cited With the recent demise of research organizations within the mining industry and dynamic changes in the industry, the supporting role of R&D groups has become limited or non-existent. Cat- reduction requirements and new raw-material sources offer future opportunities for R&D organizations to continue their effective participation in the commerical development of new chemical products. Potential areas of interest for future process applications are reviewed.

Jan 1, 1986

By Mohamed Gamal, Bill Zietlow

"In oil fields that have been depleted with conventional surface oil wells but still contain significant reserves, an extraction alternative that has been constructed recently consists of a drilling gallery below the oil-bearing formation at the bottom of a 1,200-ft deep shaft where upward sloping wells are being drilled to allow oil collection by gravity. The gallery is 92-ft diameter with a flat ceiling supported by rock bolts and shotcrete structurally connected to the shaft liner, which doubles as a large tension support element. A special excavation sequence was implemented for the gallery to maximize arching in the stress above the large diameter gallery. The gallery was located in competent sandstone, constructed with sequential excavation methods, and designed with a 3D finite element model. Special consideration was given to optimizing the gallery location to take advantage of the geology for construction and support while giving good positioning to the well drilling equipment. BACKGROUND Brierley Associates was contracted to provide both design and construction management services for an approximately 1,165-ft deep, 18-ft excavated diameter vertical shaft that opens to a 92-ft diameter flat roof gallery. The geotechnical data for the site was based on information available from literature and from data obtained during core drilling and from in-situ testing in a 1250-ft deep borehole. Wire line coring was conducted using a HQ, 10-ft long core barrel with a mud-rotary drilling method through sedimentary bedrock. The geometry of the shaft and the bottom gallery is shown in Figure 1(a). GEOLOGIC SETTING AND STRUCTURAL GEOLOGY The stratigraphy at the site includes a series of interbedded marine limestone, shale, claystone, siltstone, sandstone, and chert units. Limestone and shale are the predominant lithologies in the upper approximately 675 ft, while the lower portion contains five distinct sandstone units and more abundant shale, claystone, siltstone, and coal than the upper zone. A cherty sandstone at a depth of 1,130 below ground surface (bgs) was encountered. At a depth of about 1,000 ft to 1,116 ft bgs, a non-marine sandstone unit was encountered. This sandstone is the hydrocarbon bearing layer. Joints and fractures observed in the limestone had dips ranging from 0 to 90 deg. from horizontal with joint and fracture surfaces that ranged from planar to irregular and smooth to rough. Several, near vertical shear planes with slickensides were observed with surfaces that were generally smooth and planar. RQD values for the limestone ranged from 0 to 100 percent but in general were good to excellent."

Jan 1, 2016

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design on power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanisms of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived, and basic recommendations for mill speed and liner configuration are presented.

Jan 1, 1981

By Yehia El-Ibiary, M. P. Evans

One way of increasing conveyor systems productivity is by monitoring the key parameters in the systems. In this paper, a new line of smart bearings will be presented and discussed. The new bearings are capable of monitoring temperature, vibrations, and belt speed for early detection of potentially serious problems. The new smart bearings have built in sensors that are carefully integrated and protected for long life service. These bearings are going to be the key to increasing the up time of belt conveyors in the future.

Jan 1, 1996

By E. Bonates

Dispatching systems have attracted considerable attention in the last years due to substantial gains in productivity achieved through their implementation. These systems will be extensively used in the future by mine operators as a means of optimizing productivity. This paper describes a computer simulation model designed to study the feasibility of continuously dispatching trucks in open-pit mines based on different operating procedures. The system developed is semi-automated and performs an active role by suggesting to the dispatcher the best assignment according to each specific circumstance. It is modeled based on an advance-clock increment to reduce computing time and allows the insertion of heuristic dispatching policies and equipment real-locations when breakdowns occur. Dispatching procedures taking into account long-term production objectives are considered in system development.

Jan 1, 1988

There are many risks associated with the storage of nuclear or other toxic wastes. One of the major risks is the escape of material from the repository. No matter how well a storage facility is engineered, the potential escape of dangerous material must be studied. This kind of study will include some estimation of the "travel path" of the particles. The travel path of a radio-nuclide particle will depend on the geological and hydrological parameters of the surrounding rocks. These parameters must be estimated from a limited number of samples available within the study area. Any estimation will -of necessity -contain a certain amount of uncertainty or "estimation error". This uncertainty will be carried through to the analysis of potential movement of particles, so that the estimated travel path itself will be subject to some error. This paper discusses an approach which may lead to a quantification of the uncertainty on the predicted travel path.

Jan 1, 1989

By A. Mayton

The prolonged exposure of equipment operators to shock and whole-body vibration (WBY) is linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBY. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 1998

By Y. Gonzalez

The reaction kinetics of sulfuric acid leaching of brass foundry flue dusts were studied. As received flue dusts were separated into two size fractions, a coarse fraction (median size 103.5 microns) and a fine fraction (median size 3.4 microns). Experiments were performed on both fractions al-though most results are reported for the coarse fraction. Leaching experiments were conducted in a stirred reactor to determine those factors which govern the kinetic response of the sys-tem. The kinetics were followed by determining the increase in the concentration of dissolved copper with time. The effects of temperature, concentration and oxygen partial pressure on the rate of copper dissolution were examined. In addition, reaction residues were examined by SEM, EDAX and X-ray analysis. An activation energy of 4.8 kcal/mole (20.08 kJ/mole) was calculated. The rate was found to be significantly dependent on oxygen partial pressure and acid concentration. The order of the reaction with respect to oxygen partial pressure and hydrogen ion concentration was approximately 1.50 and 0.37, respectively. Results indicate that the dissolution reaction is limited by diffusion and can be described by the following mathematical expression where ~ is fraction of copper extracted in time t

Jan 1, 1988

By W. L. O?Connell

[Patent Issue No. Date Issued To Subject 386,504 July 24, G. Sweanor The separation of quartz from a 1588 metal with a liquid such as CS2 or CHC13 under water by introducing mixture into water layer. Quartz will stay in water layer while metal sinks through organic.]

Jan 1, 1963

By J. J. Antony

The Cactus Gold Mine is a joint venture comprised of Middle Buttes Partners Ltd. (CoCa Mines, Inc.--operator, T. Congdon and W. Carey) and Compass Mining, Inc. The project includes 2.4 sq. miles of contiguous mining claims and leases in the Mojave Mining District, Kern County, California, approximately B5 miles northeast of Los Angeles. The property is readily accessible year round by all-weather roads and is within 6 miles of the main line of the Southern Pacific Railway.

Jan 1, 1988

By E. S. Bianchin

The more complex control needs of today's mineral processing plants combined with ever-changing digital technology have brought numerous improvements to process control systems. This paper discusses recent advancements in distributed control systems (DCS) which facilitate the implementation of process plant automation. Some of the topics of discussion include integrated function controllers, weigh scale and analyzer interfacing, operator interfacing, personal computers, process information management and process plant management.

Jan 1, 1988

By Michael Edesess

The salt gradient solar pond has been the focal point of accelerating international attention and interest in recent months. Only recently have most investigators in the renewable energy field come to realize the versatility of the solar pond, and its ability to overcome certain problems usually associated with solar technologies. These realizations, together with clear demonstrations in Israel and elsewhere of its technical feasibility, have combined to bring the solar pond to the forefront of renewable energy technologies. The solar pond is a natural or site-built pond, about one to five meters or more in depth, which has been altered to retard the loss of absorbed solar energy. The absorbed solar energy is usually lost through upward buoyancy of the warmed water, followed by the loss of its heat to the atmosphere. The chief solar pond technology -the salt gradient, or "nonconvective" solar pond-prevents this upward buoyancy by means of a vertical density gradient achieved with dissolved salt. The deep waters in the solar pond reach high temperatures, up to and even above the boiling point of pure water.

Jan 1, 1981

By S. S. Hsieh

The important carboxylic acid components of tall oils were tested individually as phosphate flotation reagents. These included C18 unsaturated fatty acids and C10 to C18 saturated fatty acids and resin acids. These experiments were conducted to evaluate such factors as the degree of unsaturation, hydrocarbon chain length, isomeric form, side-group modification, and cyclic structure. The effects of mineralogical characteristics on flotation response also were considered. The results of this systematic evaluation provide guidelines for selecting efficient substitute reagents and also provide fundamental data for further research on improved flotation technology.

Jan 1, 1980