Search Documents

By Richard Lovat

INTRODUCTION Soft ground tunnels may be above the ground water table or they may be subaqueous. The ground may be clays, silts, sands, gravels, glacial deposits, boulder tills, and any of these in any combination. Because of the relatively low strength and deformability of soils, difficulties often arise in soft ground tunnelling. These soil characteristics and resultant tunnelling difficulties, have had a direct influence on the development of "Lovat" Tunnel Boring Machines. We have been required to recognize and adapt to unusual ground conditions and to follow through with design, fabrication, and field maintenance to ensure dependable, trouble-free operation. The basic "Lovat" machine is a fully shielded, wheel-type with the cuttinghead driven by a monorace type bearing with gear drive incorporated in the bearing. Mechanical innovations have been added to the basic machine which complement the resources of manpower, equipment, and materials available to the contractor for a specific operation. FULL FACE SUPPORT The installation of hydraulically operated closure doors or flood control doors, at the cuttinghead, is one of the early "Lovat" technical innovations. Flood control doors provide full face support in running or flowing ground. In water bearing sands and silts the excavated material can

Jan 1, 1981

By George L. Atwood

The western phosphate field, one of the United States' great mineral resources, lies within the western states of Idaho, Utah, Wyoming and Montana. This Permian sedimentary deposit has been known since the turn of the century and since the 1920's has been mined for its phosphate content. Isolation from markets and relatively high mining costs have restricted development as compared to eastern United States deposits, but nevertheless a significant western phosphate industry has developed. Geographically the deposit covers an enormous area of about 337 000 km2 (130 000 sq miles). It covers Idaho from Pocatello east- ward, western Wyoming to the eastern flank of the Wind River mountains, and extends well into southwestern Montana and into a large area of northeastern Utah north of the Uinta Basin and east of the Salt Lake valley.

Jan 1, 1983

By David G. Chedgy

It is probably safe to assume that most operating personnel working in coal preparation plants are exposed to noise levels in excess of the MESA Noise Regulations unless they are wearing ear protection. The excessive in-plant noise levels have received little attention until recently. Noise control has not been an important design consideration in existing coal preparation plants. This situation is rapidly changing as plant owners and plant operators are requiring that new coal preparation plants be designed to provide a safe noise environment for operating personnel and also meet MESA Noise Regulations. This paper discusses the noise exposure hazards, noise generating mechanisms, and some possible noise control solutions for typical coal preparation plants.

Jan 1, 1975

By Christopher Mark

Sixty years ago, underground coal mining was the most hazardous job in the United States. Roof falls killed about 100 miners every year, more than all other causes put together. Fast forward half a century to 2016, and the first year ever with zero roof fall fatalities. Just three miners were killed by roof falls during the following six years. To understand how this historic goal was achieved, this study analyzed hundreds of roof fall fatality reports covering five decades. It found that the immediate effect of the Federal Coal Mine Health and Safety Act of 1969 (Coal Act) was to reduce the riskiest activities, like needlessly going under unsupported roof. Other hazards, like large roof falls, required technological developments before they were brought under control. Roof control plans, which the U.S. Bureau of Mines had been advocating since the 1920s, fostered the necessary improvements in both the safety culture and the mining technology.

Jun 1, 2024

By Eberhard Stolarski, Michael Tacke

When the oxidized surface gold deposits are mined out, the underlying refractory gold ores become the challenge of treat­ment systems. The size and value ofrefractory gold ore reserves are a function of recovery efficiency and operating cost. The start-up of LURGI's gold roasters at NEWMONT's Carlin site has established whole ore gold roasters as a key to high gold recoveries. The ores from several deposits of the Carlin trend are roast­ed utilizing LURGI / NEWMONT technology, which has achieved gold recoveries approaching 95%. This is in dramatic contrast to the traditional perception that roasting is limited to gold recoveries in the mid 80's. Extensive investigation in pilot scale is required to achieve stable high gold recoveries for most variables in the ore body. The key question for all pilot tests is the classic question of (ROM) run of mine ore roasting or concentrate roasting. All variables are dominated by the leaching/ recovery char­acteristics of the natural ores. The degree ofrecovery improve­ment by roasting / calcining establishes the frame of the eco­nomical conditions. The full range of flexibility is required for the design of the plant to allow for ore variations in heat values, combustible con­tents, agglomeration behavior and off-gas composition. The variables in the ore body influence, therefore, the price of the plant proportionally to its flexibility. Concentrates are usually fairly stable in composition, com­bustion behavior, heat values and particle size since they are a product of the very selective flotation process. Flotation is not the successful process step when the tailings remain high in refractory gold contents.

Jan 1, 1996

By J. Wesley Atkins

In considering the importance of lease management and administration, I have decided to approach the topic, Lease Default and Eviction: Action or Reaction, as a three phase presentation dealing with mineral lease administration and management, past, present and future. Though the title may border on the dramatic, it illustrates the real consequences of alternative approaches to property management viewed from my experience in the evaluation, development and implementation of a number of such systems and services in my current position as president of Talco Group Corporation. First, though, let's take a moment and set the stage by giving a few actual examples of why a pragmatic approach is needed in this particular area.

Jan 1, 1983

By L. Galarza

"INTRODUCTION Beneficiation of ores and minerals in a concentrator plant requires a significant amount of water [1] for the grinding and particle separation processes; most of it ends up being recirculated for reuse, slurry pumps are used after crushing and grinding feeding the ore to a classifier to separate fine-grained material (less than 5 mm) from coarse-grained material requiring further grinding. The lower ore grades [2] in the past couple of decades have demanded an increase on power size and efficiency of process machines to maintain a competitive plant throughput; Hydro-cyclone feed pumps to control both under and over milling or grinding are not the exception; Fig. 1 shows a conventional drive train [3] comprising an (1) asynchronous motor (also known as squirrel cage induction motor = SCIM), a high speed coupling (2), a gear reducer (3) and a low speed coupling (4) attached to the shaft of the pump (5), to accommodate the motor rated speed (typically 1800 rpm) to the process requirements (in the range of 250 rpm to 350 rpm), requiring additional components related to the gearbox: instrumentation, maintenance, disposable lubricants and filters, spare parts, thus reduces the overall system efficiency ultimately reflected into CAPEX and OPEX.WHY VARIABLE SPEED DRIVES FOR CYCLONE FEED PUMPS Hydrocyclones or commonly referred as “cyclones” are one of the most important devices in the minerals industry [4]; almost universally used in close-circuit grinding because of their high capacity and relative efficiency, the evolution of Power Electronics made affordable the use of Medium Voltage - Variable Frequency Converters (VFC) for Cyclone Feed pumps in combination with induction motors larger than 500hp (373kW) to gain multiple benefits: - Soft start with minimum electrical utility disturbance = inrush current mitigation - Full Torque available at zero speed for overload startup with pulp solidification after long still stand periods, superior to any other reduced voltage starting method. - Optimum and constant pump speed (independent of the electrical network or load condition), compared to across the line SCIM operation - Flexible Motor Voltage and Speed regardless of the power distribution Voltage and Frequency - Improved Power Factor (close to unitary), over the entire operating speed range"

Jan 1, 2015

By Mustafa Kumral, Yuksel Asli Sari

Economic evaluations of underground mining operations are made based on the estimated or simulated grades of the block model as the actual values are not known. Depending on how the planning decisions are made, the risk of the operation can be managed and decreased. This research introduces a mixed-integer linear programming (MILP) model for stope sequencing optimization that considers the uncertainty associated with net present value (NPV) using chance-constrained programming (CCP). The introduced method permits achieving a balance between maximizing NPV and reducing the associated operational risk through transforming the problem into a multiobjective problem, where the objectives are maximizing the NPV and minimizing the risk. This risk is expressed in terms of the standard deviation of project outcomes, taking into account multiple possible scenarios. In a case study, the efficiency of the method was demonstrated as a decision-making tool capable of translating a specified risk or reliability level into a stope sequencing plan.

Jan 1, 2024

By Walter C. Labys

This paper reports on recent modeling efforts to analyze the eastern U.S. steam coal market with a cross-sectional econometric as well as a quadratic programming approach. The background to coal modeling is examined first. The particular aspect of the steam coal market to be modeled are then presented and the corresponding coal model described. Both empirical results and rigorous mathematic pertubation analysis are presented. Conclusions are then drawn regarding potential modeling applications in the policy area.

Jan 1, 1979

By C. B. Henderson

The development of slurries of coal and water as a boiler fuel replacing No. 6 fuel oil has been actively pursued at the Atlantic Research Corporation since 1976. Funding for this effort has been provided by the U.S. Department of Energy, the Electric Power Research Institute, and by corporate funds. The name ARC-COALTM has been selected for these slurries. Stable coal-water slurries with bone-dry coal loadings between 62% and 77% have been prepared, evaluated rheologically, and successfully burned in an experimental furnace without the assistance of other fuels. The advantages and properties of these slurries, including combustion results, are reviewed. Also discussed is the pilot line used for processing barrel quantities of fuel and a pilot plant capable of processing 600 bbl/day, currently being designed.

Jan 1, 1982

By S. Hearn, S. Boskovic, A. Smethurst

"The digestion of minerals in strong acids or at elevated temperatures can result in the release of large amounts of silicic acid which can polymerize in solution to form colloidal silica and gels. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Huntsman’s POLYSIL® polyether coagulants have a “lock and key” relationship with the surface of colloidal silica to help lower the concentration of these particles in solution, improve process efficiency and reduce reagent losses by minimizing crud formation. This paper investigates some of the issues caused by colloidal silica in hydrometallurgy processes and illustrates how the use of POLYSIL® coagulants has helped to improve process outcomes. INTRODUCTION Coagulation differs from flocculation in a number of ways. Coagulants are relatively small molecules that modify the surfaces of fine particles, weakening repulsive forces between them and allowing particles to stick together, while flocculants are generally molecules that are large enough to bridge the boundary layers between the particles. With flocculation, addition rate and mixing all make a difference to the flocs formed. Coagulation, on the other hand, is an equilibrium process. With coagulation it is only necessary to achieve good mixing, and coagulates will form as Brownian motion pushes the particles into each other. In real systems, this process is complete within seconds. Huntsman’s POLYSIL® polyether based coagulants have a strong affinity with the surface of colloidal silica formed by the polymerization of silicic acid. While silica found in minerals has a low aqueous solubility, large amounts of silica as silicic acid can be released as these minerals are digested in strong acids at elevated temperatures. The solubility of free silicic acid is about 150 ppm under pH conditions typical in acid leach environments (1), so the bulk of the silica will polymerize in solution to form colloidal silica. Colloidal silica can pass through a hydrometallurgy process without affecting any of the operations. However, it can cause a number of problems. These include gelling in a leach, interfering with flocculation or crystallization, initiating crud formation (2,3,4), decreasing extraction kinetics and increasing phase disengagement times (5,6) in solvent extraction. In these cases, coagulating the silica with POLYSIL® coagulants can reduce or eliminate the problem by enabling these particles to be flocculated and removed from the solution."

Jan 1, 2015

By Max Friedemann, Alexandros Bousdekis, Anna Gustafson, Helmut Mischo, Håkan Schunnesson

Many devices used in mining are not monitored by sensors or do not have their own intelligence. By retrofitting sensors and real-time data processing, machines can be integrated into an existing digital infrastructure. Within the project Mine.io funded by the European Union a Sandvik DE110 exploration drill rig is being digitized using various AI algorithms at research and education Mine “Forschungs- und Lehrbergwerk Reiche Zeche (FLB)” of TU Freiberg. The aim is to increase the productivity of drilling with real-time evaluation of the current rock to be drilled and the current maintenance status of the drill rig. The drill rig is equipped with a speed sensor, pressure sensors in the hydraulics, 3-axis vibration sensor, borehole length measurement and temperature sensor. The sensors are additionally attached to the drilling rig and no structural changes on the drill rig are necessary. All data are processed real-time at a server structure outside of the mine using AI algorithms to analyze which rock (ore or host rock) is being drilled and to perform predictive maintenance. Processed Data are visualized for the operator to optimize the workflow and the productivity.

Feb 1, 2025

By Hal McVey

The logic and importance of marketing in the industrial minerals industry is generally recognized by those of us intimately involved in this industry. The illogical instances where marketing is ignored in evaluating projects or poorly implemented in operations are also well known. The interplay between these two extremes is interesting territory and is explored commencing with a logical progression of a metal mine that became an industrial minerals mine and ending with the most illogical and failure-prone decision common to the minerals industry today. This paper will demonstrate how: 1. A logical progression of marketing expertise can result in previously unseen benefits to a minerals venture. 2. Logic can turn to illogic due to market conditions and price fluctuations. 3. How operations can turn marketing logic into illogical results. 4. Short term "logic" is often illogical.

Jan 1, 1981

By Hajime Kitamura, Nobuharu Isago, Yuta Yamanishi, Kosuke Kawata, Hiroshi Yagi, Akira Matsuoka

Mountain tunnels are generally considered to be stable during earthquakes, however, it is known that the portal areas are prone to seismic damages. Characteristics in portals such as the location of the slope, modulus of ground deformation, and the change of overburden are different for each tunnel, and damage degrees are unclear. In this study, we reproduced the seismic behavior to investigate the effect on the tunnel portal by considering some parameters above, using simple static model tests and numerical analysis. As a result, the conditions of the slope condition and minimum distance from slope was confirmed to influence on the mechanical behavior of the tunnel portal during earthquakes.

Dec 1, 2022

By RICHARD A. THOMAS, Liming Yuan, Lihong Zhou, DAVOOD BAHRAMI

Mine ventilation simulation software has become an essential tool for the mining industry to design and manage mine ventilation operations. Building a well-calibrated mine ventilation network is time consuming, however, and requires great effort. In the last several decades, the mining industry has seen a steady increase in the use of air velocity sensors to monitor airflow and detect unexpected abnormal airflow in some key locations in underground mines. The present research work was carried out to explore the possibility and methodology of calibrating a ventilation network model using atmospheric monitoring system (AMS) data on a routine and ongoing basis.

Aug 1, 2022

By Hiroyuki Abé

This paper is a review of research and development on geothermal energy extraction in Japan especially on hydraulic fracturing. First recent geothermal developments in Japan are outlined in Part I. An increase in the production rate of geothermal wells may be highly dependent on the geothermal well stimulation technology based on hydraulic fracturing. The hydraulic fracturing technique must be developed also for geothermal energy to be extracted from hot, dry rock masses. In Part II, the research on hydraulic fracturing and field application are reviewed.

Jan 1, 1982

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Variations of cut-and-fill stoping are the most com¬monly used methods for mining narrow, nearly vertical veins in the United States. These methods offer the best results for maximum recovery with minimum dilution of ore from veins that are irregular along either the strike or dip. The vein is developed along the strike length in 61 to 122-m (200 to 400-ft) blocks or stopes and vertical lifts of 48 to 61 m (160 to 200 ft). The level development is either on the vein or parallel to the vein with crosscuts intersecting the vein at right angles. Chutes, manways, and haulageways are established in the center of the stopes at the lower level of the ore block. Mining then proceeds by blasting down horizon¬tal cuts of the vein in both directions from the chutes. As the blasting continues to the outer limits of the stope, the broken ore is slushed into chutes. When a complete horizontal cut has been made, the service raise, including chutes, is raised to a height of a few feet from the back and the stope is filled with either sand fill or waste rock. Then the mining cycle is re¬peated until the stope reaches the level above. LEVEL DEVELOPMENT PRACTICES FOROVERHAND CUT-AND-FILL STOPING The two basic methods used are: the development of the haulage drift within the vein, or development of the haulage drift paralleling the vein in the foot or hang¬ing wall with crosscuts intersecting the vein perpendicu¬larly at 61 to 122-m (200 to 400-ft) intervals. The il¬lustrated methods of development show some of the variations which can be used to develop a stope block. Development for cut-and-fill stoping does not require the more elaborate schemes outlined for shrinkage or sublevel long-hole stoping. Many factors must be considered before deciding on a particular development plan and usually the nature of the vein or host rock will dictate which specific method to use. If the vein is relatively straight, then develop¬ment on the vein is feasible. Excessive ground pressures will necessitate the leaving of a sill pillar (Fig. la) and highly fractured or "heavy" ground will require timber¬ing (Fig. 1b). Development on the vein has the advan¬tage of reducing capital outlay and waste handling prob¬lems since the mined rock has value. But removal of the sill pillar is costly and time-consuming. Also, where no sill pillar is left, excessive timbering and subsequent level repair is a drawback. Development in either the footwall or hanging wall is the more common procedure and offers greater flexi¬bility in overall development of consecutive stoping blocks by partially disassociating the level development from stoping (Fig. 2). Chutes, manways, and service compartments com¬prise the next stage of development and are established in a variety of ways. They provide access to the stope, ventilation ducts, and muck removal. Several different development systems are in common use and average costs for each have been developed. Raise borers are used to establish ventilation and ac¬cess from level to level. They are normally reamed with 1.5 or 1.8-m (5 or 6-ft) cutterhead and may either be left bald or lined with a 1.2-m (4-ft) diam corrugated liner plate, depending upon ground conditions. The use of an Alimak raise climber is another effec¬tive method of driving a raise from level to level. The size usually is 2 m (7 ft) square. This will accommodate square-set timber which is later installed. This method of raising is not common, although it is a valuable tech¬nique especially when level spacing is several hundred feet.

Jan 1, 1982

By Edward J. Hasenohr

Geochemical studies were under- taken in the Breckenridge mining district to test the effectiveness of soil and rock-chip samples in high- lighting known mineralization in the district, and in locating sites of possible porphyry-type mineralization, if such mineralization is present in the area. Soil sampling can be done more quickly and more cheaply, but it does not provide a direct site- specific sample of mineralized rock. In well-developed soils, supergene effects may mask and/or displace primary hypogene effects; and even in places where the soils are poorly- developed, as in the Breckenridge district, the masking effects may be felt. Soil anomalies, if present, likely will be of lower amplitude and more diffuse (widespread) than corresponding rock-chip anomalies. On the other hand, detailed rock-chip surveys are more time-consuming and expensive, even though they yield direct geologic information in addition to the chemical data. The goals of the combined soil and rock-chip programs were (1) to com- pare the data from the two; and (2) test the effectiveness in identifying significant chemical anomalies with respect to the geology of the district, as it is presently understood.

Jan 1, 1982

By Joseph Cervik

Common methods of controlling gob gas in U.S. nines are by means of ventilation of gob areas and gas drainage through surf ace boreholes. Costs of drilling surface gob holes increase as deeper coalbeds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States, This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1979

By Victor F. Hollister

This first section of case histories of mineral discoveries, Vol. 3, covers some of the milestones in porphyry copper and skam exploration successes. It was during the era of these discoveries that large, complex exploration departments emerged as permanent adjuncts of large mining companies. The discoveries helped shape how and where exploration activity was conducted. Probably the most important factor in exploration success is management. Few management people are mentioned in this section or in any exploration history, yet the distinction between success and failure ultimately rested with the decisions they made. One of the most successful groups was initiated by Roger Straus and Herbert Brownell when they sought to make Asarco into an important metal producer. Relying on Clem Pollock and L.H. (Bill) Hart to identify and push worthwhile projects, the Asarco management remade the company. Asarco will benefit from exploration successes com- pounded by that team for years to come. Duval is an example of a management that decided to add metal production to its industrial minerals output. When Page Morris was president, that company opened three major porphyry copper mines and became an important factor in metals. Under the Monis management team, Duval became a leader in exploration. At the other end of the scale are managements that snatched defeat from the jaws of victory and by so doing changed the character of their companies in other ways.

Jan 1, 1991