Search Documents

By R. L. Garrett

The quality of mineral additives used 1n a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally used minerals are bentonite, barite, barite/hematite blends and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity, gel strength and to provide a low permeability filter cake. A multi-million dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason why oil companies who use these materials sometimes set their own quality standards beyond those already specified in API Spec. 13A. Also discussed in this paper are the current standardization activities in API Committee 13 on these minerals.

Jan 1, 1986

By Jamal Rostami, Tom Iseley, Saleh Behbahani

Tunnels and underground infrastructures assets, like all assets, deteriorate with time. At some point, they reach the end of their useful life. Therefore, frequent inspections, higher levels of maintenance, and rehabilitation are needed to address loss of life and safety concerns. The repair cost of tunnels will increase if maintenance of tunnels is not satisfactory and timely. Historically, tunnel inspections have primarily relied on visual and manual procedures. Due to their time-consuming nature and susceptibility to human error, there is a demand for alternative automated techniques that can enhance efficiency and reliability in tunnel inspection. By utilizing a tunnel scanning system, such as laser scanner and thermography, or photogrammetry system, tunnel inspection cost, time, and personnel can be reduced. The goal of this study is to utilize deep convolutional neural networks (CNNs) for automated identification of defects in tunnel lining inspection. This paper presents a framework to classify two types of defects in tunnel lining (water leakages and cracks) using CNNs. The CNNs were trained and tested using 4,608 images. The Precision, Recall, and F1 Score were each 99.6%, confirming the viability of this approach in the automated defect identification in tunnel lining.

Jun 23, 2024

By L. W. Pommier

In the field of minerals processing the concentration of valuable minerals normally takes place in suspensions of ore particles in liquids. The fluid resistance offered by Newtonian liquids to the movement of free settling spheres for the limiting cases of creep flow and turbulent flow is well described by Stokes' and Newton's Laws. However, these equations are not applicable to non-Newtonian fluids, since the relationship between applied shearing stress and resulting rate of shear is a non-linear function, and more than one viscosity parameter is necessary to describe their rheological properties. For this reason, the term "apparent viscosity," which has been commonly used to explain the flow resistance of the non-Newtonian systems including suspensions, may be misleading. A rigorous analysis of the mechanisms of momentum transport of solid-liquid systems is complex indeed. There are many variables that affect the properties of such systems, and precise limitations and assumptions are necessary in order to produce quantitative relationships for predicting their behavior. Very dilute suspensions of spherical particles in Newtonian liquids of identical density as the solids have been examined in the past (12); however, the study of suspensions in which there is a considerable difference in density, between the liquid and the suspended solids has been neglected.

Jan 1, 1968

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By William C. Larson

The Bureau of Mines, as a result of its contract research program, is developing a retractable core bit for the wireline drilling system (Retractable Sit System, No, H0272004). The prime contractor, Longyear Company, Minneapolis, Minnesota, and the subcontractor, Doerfer Division, Cedar Falls, Iowa, have designed, fabricated, and are currently field testing the in-hole retractable bit system. he objective of the program is to develop a minerals exploration core drilling system that allows retraction of a worn out bit and insertion of a new core bit, without pulling the drill rods out of the hole. To date, the results of the project are encouraging, and the retractable bit contract is currently in the last phase of a four-phase program, which is on schedule and under budget.

Jan 1, 1980

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The overburden responses in gently inclined orebody mining are different from those in horizontal orebody affected by the orebody dip angle. In particular, the mining-induced stress presents asymmetrical distribution characteristics spatially, resulting in stress concentration and large-scale pressure relief phenomenon in the surrounding rock. As a result, frequent ground pressure disasters such as roof collapse and barrier splitting occur frequently. Moreover, the ground pressure evolution law and the interaction between stopes in multistope mining are complex. The effective ground pressure control measures cannot be taken due to unclear understanding of the evolution of stress and displacement fields, justifying the investigation of the distribution and evolution of underground pressure for safe and efficient mining.

Jun 1, 2023

By S. Afrouz, C. Keles, W. R. Reed, E. Sarver, T. Akinseye, A. Greth, L. Pan, F. Animah

The resurgence of severe lung disease among U.S. coal miners has not only highlighted the need for improved dust controls, but also the need for an improved understanding of dust characteristics and monitoring strategies [1]. Following up on prior work by the National Institute of Occupational Safety and Health (NIOSH) to demonstrate a novel wet dust collection system on a roof bolter [2], the current study explores the effect of that system on dust characteristics and uses interlaboratory comparisons to comment on analytical methods. Results indicate the wet system did not appreciably affect the composition or size of respirable dust in the vicinity of the operating roof bolter. However, the system does appear to have substantial benefits for the operator. NIOSH has already shown it can reduce the respirable dust mass concentration to which the operator is exposed during dustbox cleanout [2,3], which is a frequent maintenance activity that can re-aerosolize dust, and new results here indicate the silica and silicates content in this dust may also be reduced, thereby reducing the overall hazard. Moreover, regarding analytical methods, excellent correlation was demonstrated between measurements of quartz mass, taken first by NIOSH and then by a university laboratory, using direct-on-filter Fourier transform infrared (FTIR) analysis. This method is the basis for envisioned “end of shift” silica monitoring (quartz is the predominant form of crystalline silica in coal mines) [4]. For particle-level analysis by scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), there was more variability in results generated by two independent university laboratories.

Mar 1, 2024

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

By K. W. Morris

Of the fossil fuels used for power generation coal is by far the most variable and complex in its properties. A thorough review of the characteristics of the coal to be fired is essential before boiler design can begin. Major parameters such as heating value, moisture content and ash properties will determine not only the boiler size and configuration, but also the performance of the unit with respect to the thermal efficiency, particulate and gaseous emissions, and unit availability and reliability. An example of a review completed on a large low-rank coal deposit for a power plant will be described.

Jan 1, 1983

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

Steel slag is an industrial byproduct of steelmaking that is mainly composed of calcium, iron, silicon and magnesium. In addition, depending on the different raw materials entering the furnace, steel slag contains a certain amount of vanadium that is the main source of vanadium production, accounting for 69 percent of the species of the total vanadium raw material [1]. From experience, the production of one ton of steel will generate 1.0 to 1.5 tons of steel slag [2]. However, the utilization efficiency of steel slag is less than 30 percent, and a large amount of steel slag is identified as waste and stacked in tailings. The random stacking of steel slag not only wastes large amounts of limited steel and land resources but also exerts pressure on the environment [3], making it imperative to research the effective utilization of steel slag and recycling of metal resources.

By Dominick Mandalari, David Mast, Heather Ullinger, Juan Granja, Amanda Foote

The City of Akron will construct the Northside Interceptor Tunnel (NSIT) project to control and reduce combined sewer overflows. One component of the project a large diameter tunnel diversion / flow control structure that will facilitate tunnel storage, divert dry weather flow to the treatment plant, and divert large wet weather events that are greater than the tunnel capacity to the Cuyahoga River. The structure is designed to pass up to 1.2 billion gallons per day of flow and includes floatables screening. This paper will discuss project background, factors that influenced shaft location, and options evaluated to manage the large design flows.

Jun 23, 2024

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By R. E. J. Putman

Rising demand, artificial market conditions, increased overseas competition, and a fluctuating international situation have brought ever increasing pressures to bear on the nonferrous metals industries, and particularly in the United States, Although capacity is being expanded by the construction of new plants and the development of new ore deposits, increasing attention is being focused on the possibilities of improving the performance of the existing installations and of getting the most out of the new equipment now installed. At first sight the task appears formidable. Based on raw materials which are nonhomogeneous, and possessing characteristics which are hard to quantify, even the processes by which the values in the ores are concentrated and extracted are in many cases not fully understood. The necessary analytical equipment and transducers demanded by these industries have also been slow in development and their earlier absence has hampered the application of modern control technology, This is reflected in plants which have been designed for ease of manual rather than automatic control, and in which the application of control techniques at first sight appears economically prohibitive. However, in any industry progress often comes only in small steps, It may be that by the wise choice of limited objectives and perhaps only partial solutions, substantial improvements in plant performance can be implemented now, and with only a modest investment. If modern control equipment is chosen of the type which can be reprogrammed, advantage can be taken later of more sophisticated solutions as the technology of the industry advances. This task of improving plant performance can and must be commenced even though our knowledge is incomplete. The experience of a related mineral consuming industry, with similar problems in the past, can be encouraging.

Jan 1, 1967

By Gunjan R. Bhattarai, K. Bhattarai

Applications of machine learning and robotics in the tunneling industry are still nascent. Research and development are ongoing in TBM guidance; prediction of TBM cutter wear and tunneling induced ground deformations; and robotic arms for segment installation, inspection, cleaning, and maintenance of TBM cutting tools. This paper presents a case study of geological profile reconstruction using multimodal machine learning. The results from this study can aid the development and application of multimodal AI technologies to generate data reports and geological profiles in real time, taking voice recordings, photos, or videos obtained directly from the field as inputs.

Jun 23, 2024

By C. Treworgy

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Jan 1, 1997

By Rennie B. Kaunda, Robert J. Sterrett

Some people in the mining-engineering field mistakenly believe that mine-water management primarily revolves around the treatment of mine waters that fail to meet applicable water-quality standards. While water-quality control is undoubtedly important, it represents only a fraction of what constitutes comprehensive site-wide, minewater management. A more holistic perspective recognizes that it also involves mine dewatering to maintain safe and workable conditions, securing sufficient water supply for operations, strategically handling surface water within and surrounding the openpit to prevent issues like flooding, developing robust post-closure plans to mitigate long-term environmental effects, and proactively minimizing any adverse impacts on local communities and ecosystems. This article provides a brief overview of topics that fall within the concepts of mine-water management. The focus is on openpit mines, as they are generally larger than underground mines. The management of mine water is highly dependent on local and regional climate such as tropical, desert or temperate climate. Each climatic setting has its own unique challenges, but there are also commonalities.

Jun 1, 2025

By K. Katen

In another situation, Dave Zegeer, the Assistant Secretary of Labor for Mine Safety and Health, whom all of you know very well, would have taken the opportunity to talk with you. In his absence, however, I would like to reference some of his recent comments which may help us to see the issue of mine safety in historical perspective. Dave pointed out that this year is the eightieth anniversary of the Great Earthquake and Fire of San Francisco. The whole world heard about that disaster--it and the 452 people who died in it. In that same year, nearly five times as many people died in coal mines, but no one particularly noticed.

Jan 1, 1986

Mine planners must select a single pit for design with the knowledge that the grades on which this selection is made are uncertain. This uncertainty is often ignored through the use of deterministic models of grade. This makes the mine planner?s job simpler but does not necessarily lead to the ?correct? or ?best? selection. Grade uncertainty is typically modeled with conditional simulation, which generates multiple possible realizations of grade that are equally probable (or improbable). M ethods for incorporating grade uncertainty into mine planning to date have either been perceived as being too complicated, not accessible or too time-consuming. This paper proposes a simple and efficient modeling approach to incorporating conditional simulation into pit optimization, which would be able to be applied in currently commercially available software. An example for R esolute M ining Ltd.?s Syama gold project in M ali shows the range of ore, grade and value outcomes associated with generating pits through a variety of methods.

Jan 1, 2013

By W. T. Reid

Analysis of the energy resources available in the United States confirms that coal will be needed to satisfy the future energy needs. The trends in the market place, particularly economic and political, suggest that the bulk of the coal will be consumed for generation of electricity. The utilization of coal to produce electricity will require technical solutions to the variable characteristics of coal and ash, development of methods to improve coal quality, and public acceptance of the cost of compliance with environmental standards.

Jan 1, 1983

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018