Search Documents

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.' Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.' The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

By Leonard Sugin

The requirements of today's and tomorrow's markets led to a new generation of facilities which handles large tonnages annually, loading them into larger vessels, at higher rates, efficiently and reliably, with minimum labor input, and significantly greater attention to the environment. A great variety of products are handled, including various grades of metallurgical and steaming coal, coke, iron ore in its many forms, shapes and moisture content, phosphates and fertilizer products, bauxite and alumina ores, limestone, sugar and grains, cement and many other products. When we examine the annual tonnages involved in these movements the economic value of handling these products on a bulk basis can be readily seen. Although nearly all these products have been handled by continuous bulk conveyors for many years, recent governmental response to environmental concerns require a re-evaluation of previous procedures. Most air pollution and emission control regulations and ordinances have recognized several specific sources of pollution. Detailed regulations and requirements have been developed concerning smoke emissions, emissions of visible air contaminants and particulate matter from power plants, heating plants, refuse burning equipment, coke ovens, steel furnaces, kilns, and other industrial installations. Although fugitive dust is also an environmental pollutant it is governed by regulations that are more general and therefore, more difficult to apply. A general definition of a "fugitive particle" is any matter which escapes or becomes airborne from an operation or which is emitted into the atmosphere without passing or being conducted through a flue, pipe, stack or other structure designed for the purpose of emitting air pollutants into the atmosphere. This paper deals with the aspects of fugitive dust emissions as they apply to shiploading. Fugitive dust emissions control is important not only because of environmental regulations but also to prevent the loss of valuable product, reduce housekeeping, and reduce breakdown and maintenance problems to land and vessel equipment. The environmental controls for a belt conveyor system are those which will restrict the emission of fugitive dust particles and can be considered as follows:

Jan 1, 1977

By Jacek Galas, Stanislaw Lenczowski

The image of the flotation froth surface in the mineral processing plant contains the information about its composition. This information can be very useful for a technological process automation. Images, captured in the optical part of the measurement system were read by the computer, then were transformed and analysed digitally. The set of image parameters, extracted from an image transforms, was evaluated by statistical analysis. The recognition algorithm constructed in this process allowed to estimate the froth composition.

Jan 1, 1995

By J. P. Bunch

As the number of environmental laws continues to steadily increase and the economic penalties for contamination problems become more severe, environmental management represents an important management function within today's U. S. mining industry. The economic impact to a mining company for contamination is not only realized in legal fees and fines but also in the cost of doing normal business. For example, a mining company with contaminated property applying for a loan may be refused because of a lending institution's reluctance to finance due to liability concerns. Or, an insurance company may decide to greatly increase its annual premiums because of existing or potential contamination problems. One of the main duties of the environmental manager is to seek ways to reduce these types of problems by eliminating contamination or by knowing what problems exist and designing corrective measures to prevent the situation from worsening.

Jan 1, 1990

By R. K. Singhal, D. B. Stewart

A variety of equipment is being used for roadheading and tunneling in the mining industry. In United States drum-type continuous miners are used most extensively. In Europe and Canada mine roadways are driven mainly by roadheaders. The application of tunnel boring machines to coal mining is somewhat recent. Such machines are however being used on major projects driving main mine entries.

Jan 1, 1985

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry's perspective on a number of the issues currently being addressed at EPA's Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992

By Dale C. Matthews

Pressure oxidation of refractory gold ores is becoming more popular in our environmentally sensitive society. This paper will discuss some specific process problems and solutions involved with starting up and operating an autoclave circuit.

Jan 1, 1991

By Clarice L. Amaral, Ricardo Melamed

Clay-coating has been used as an environmental technology tool for the immobilization of toxic elements. The mechanisms of arsenate retention in clays suggest that not only the system pH is of fundamental importance in the process but also the character of metals and ligands that compose the electrolyte system. The goal of this study was to investigate the interactions between system pH and electrolyte ions on the retention of arsenate in an Oxisol soil. The sorption of arsenate decreases with the increase in system pH, reflecting the competitive sorption of arsenate with OH groups. Solutions containing Ca tend to favour the immobilization of arsenate in a relatively broad pH range.

Jan 1, 1998

By M. E. Gershon

Extensive efforts are under way toward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics, and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1987

By O. Ozcan

Oleic acid has been almost invariably used in the flotation of siliceous fluorite ores. The performance of oleic acid, however, deteriorates with carbonaceous fluorite ores. Oleoyl sarcosine developed recently has been found to produce results superior over oleic acid with ores containing high calcite contents. While the mechanism of oleate adsorption is usually considered as chemisorption involving calcium oleate formation on both calcite and fluorite, no mechanism has been so far proposed to explain the adsorption mechanism of oleoyl sarcosine. In this study, the selectivity of oleoyl sarcosine, as inferred from flotation, zeta potential and infrared measurements, is ascribed to the interaction of fluorine ion to the nitrogen via hydrogen bonding.

Jan 1, 1994

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By L. B. Phelps

The nation is confronted with thousands of acres of abandoned coal lands. In Pennsylvania alone, these lands have been estimated to cost $15 billion to reclaim (Pennsylvania Bulletin, 1985). One way to deal with this problem is to provide a mechanism by which the active mining industry can undertake to remine certain of these abandoned mine areas. Remining is classified as reaffecting previously mined areas in order td extract the remaining coal reserves while improving the environmental quality of these lands through land restogation and abatement of pollutional discharges. However, there currently is a disincentive for operators to plan to extract reserves on these abandoned mine lands which have preexisting pollutional discharges. Therefore, they presently avoid them. This is because of the "potentially unlimited liability of post- mining treatment for any discharges that would remain after mining? (Pennsylvania Bulletin, 1985).

Jan 1, 1987

By Richard J. Goff

Technical Support, one of several major organizational units in the Mine Safety and Health Administration, provides technical assistance to the mining community in all areas of health and safety. One of its many areas of expertise is noise control. Depending upon the needs of the operator or inspector, the services provided can range from locating major noise sources to actually building noise controls. Over the years a vast amount of knowledge has been obtained as to what will work and what will not. DESIGN GOALS While many noise controls have been developed for mining equipment and operations, the most acceptable (ergo successful) have achieved the following design goals: - a noise level reduction of at least 5 decibels; - minimum interference with production; - inexpensive to install; and - effective in reducing low frequency noise.

Jan 1, 1984

By Rolando V. Cuaño

For geostatistical applications, heterogeneous spatial phenomena are better modeled as mixtures of populations. However, the modeling of the constituent populations can become complex. The alternative mixture model offers a simplified approach to the w modeling problem. The model is applied and tested on the Walker Lake data set. Compared to the univariate ordinary kriging model, the alternative model generates less biased block estimates.

Jan 1, 1996

By Lester E. Sutton

The past three years have been the most difficult period in the modem history of the barge line industry. Having withstood the fuel cost run ups of the late 1970s and the imposition of inland waterways system user fees, the industry has struggled more recently with an overcapacity problem of unprecedented proportions. In responding to these challenges, the industry is undergoing important long-term structural changes, with the various individual barge lines pursuing an array of divergent long-term business strategies. This paper discusses these strategies in terms of their probable impact on the industry as a whole, and argues for the survival of a competitive number of large, national, independent barge lines as the outcome most in keeping with the long-term interests of the mining and minerals industry.

Jan 1, 1986

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

This paper reviews the historical literature and the author's experience with regard to the effect that the selection of grinding ball size or sizes has on ball mill grinding efficiency. The conclusions presented provide guidelines for single and multi-size charging prac- tices in commercial milling operations.

Jan 1, 1998

By K. V. Viswanathan, P. Sornasundaran, S. E. El-Mofty

Dolomite is found to undergo preferential dissolution in aqueous solutions and this is found to be strongly dependent on the solid to liquid ratio (SIL). Electrokinetic studies done under the sump conditions revealed that the mineral surface charge is also affected markedly by the solid content in the suspension. Conditioning of the dolomite at low SIL ratios for short time intervals showed preferential dissolution of calcium leading to a magnesium-enriched dolomite surface. At higher SIL ratios and longer conditioning times, calcium depletion from the solution and a calcium-enriched dolomite surface resulted. The results are discussed in terms of surface precipitation and/or bulk precipitation and surface conversion of dolomite to the calcium-enriched phase (calcium carbonate and/or magnesian calcites).

Jan 1, 1990

By R. E. Hochscheid

Cyclones installed in three closed- circuit grinding systems were changed from conventional, vertical mounting to horizontal mounting with a favorable improvement in classification efficiency. In two of the installations, apex plugging problems were eliminated because horizontal mounting permit- ted the use of much larger apex orifices. Marked reduction in circulating load was accompanied by greatly reduced maintenance requirements for the cyclone and the cyclone feed pump in one of the installations.

Jan 1, 1988

By K. Kim, H. Gao

A site-characterization strategy formulated for the probabilistic assessment of rock mass properties is presented. The strategy, which takes into account the variability of rock properties and the stochastic nature of the rock-failure process, entails determining probability distributions of rock properties by utilizing extreme value statistics and Monte Carlo simulation. Laboratory and, field test data are analyzed and presented to illustrate the methodology. The results indicate that the distributive characteristics of rock mass can be estimated by using this proposed method. The results of the analysis can be incorporated into the design of underground structures. Then, the relative uncertainties of the failure probability of the structures can be assessed.

Jan 1, 1997