Search Documents

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By J. L. Kohler

Control circuit failures contribute significantly to continuous miner downtime. The time required to put the machine back into production is a function of the time required to diagnose the problem, obtain parts, and make the repair; of these, the diagnostic time is often the largest. A microprocessor-based system with the ability to diagnose all of the common control circuit failures was designed, installed on a continuous miner, and tested. This paper summarizes the development of the diagnostic system, and provides examples of the system's diagnostic capabilities. Implementation issues and the hardware used for the prototype are briefly described. Finally, comments on the system's performance are presented.

Jan 1, 1993

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By James Wm. White

Calculation of consistent steady-state mass balances in operating metallurgical plants and pilot plants is of interest for many reasons. In general, enough data can - and should - be collected to overdefine the system, i.e., permit calculation of nonmeasured quantities via more than one path. In such cases, resulting steady-state metallurgical mass balances rarely close due to sampling, analysis and/ or instrument error. Indeed, determination of a valid calculational sequence for complicated process flowsheets with multiple recycle streams can prove quite difficult. Here we present and discuss a method that has proven useful in analysis of numerous grinding circuit flowsheets of varying-degrees of complexity our technique requires only a consistent process flowsheet with appropriate associated data and arbitrary numbering of streams and equipments. Process topology and user data are decoded to yield a set of "search" or base variables and a set of "calculated" variables in solids, water, particle size and splitter parameter space. This procedure greatly speeds subsequent actual mass balance adjustment calculations since perturing certain variables (e.g., a solids value) does not require recalculation of other variables (e.g., the water balance). Finally, internal search and calculated variables are back converted to User units and used in a Sum-of-Squares criterion. Global minimization of this performance functional then yields a consistent mass balance in a least, squares sense. Weighting factors of choice can be used. Examples illustrate application of these methods.

Jan 1, 1979

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By R. L. Braun

In situ chemical mining of primary sulfide ore requires distribution of injected oxygen in a large underground flooded region of broken ore. Although the maximum oxygen content of the leach solution will be dictated by the operating temperature and hydrostatic pressure, the actual oxygen content will be limited by the geometric dispersion of the injected oxygen, the rate of dissolution of oxygen, and the rate of convective circulation of oxygenated solution within the flooded bed of ore fragments. These factors are examined by a detailed theoretical analysis supported by laboratory experimental data. Typical results of the study illustrate that adequate dissolution of oxygen and circulation of oxygenated solution can be obtained in a column of 4 million metric tons of broken ore by using three gas injection lines and an oxygen injection to consumption ratio of 1.84.

Jan 1, 1974

By Ming-yi Zhang, Zhong-nian Yang, Xiao-ming Guan, Quan-wei Liu

"In slurry balanced shield tunneling, how to ensure the safety of construction and to reduce the influence on the environment has arisen wide attention of scholars both at home and abroad. But now it is still in the stage of experience as to the instability mechanism of the slurry shield tunneling excavation and its stability analysis. Based on the large-diameter model tests and FLAC 3D, the effect of the different waterhead (non-water, 0.9m and 1.1m) on stability of excavation face of slurry balanced shield is investigated, and the stability mechanics is proposed. The results show that: waterhead heights play an important role on excavation face instability features of slurry balanced shield in sandy stratum, Regarding the different waterhead heights, the development mode of the excavation face instability features can be divided into non-water mode, lower-waterhead mode and higher-waterhead mode; soil arching is existed in the process of excavation face instability, the settlement of ground lags behind excavation face failure, the soil arching will block or eliminate the effects of ground settlement; excess pore water pressure need to be considered besides earth pressure and hydrostatic pressure when the supporting force is calculated. INTRODUCTION With the development of the society, for the cities all over the world, the exploitation of underground space has become an important measure to solve the problems about population, resources and environment and an important way to heal the city syndrome and implement the sustainable development strategy of city. Constructing shield tunnel with large diameter is the major trend for development of tunnel construction (Yin, 1999). Instability of excavation face caused by relief of shield soil stress is still one problem that needs to be solved (Xiang, 2001). How to reduce the effects of construction on surrounding environment? How to accurately determine the instability of shield excavation face and to effectively and reasonably select the supporting force? These are the crucial problems which need to be solved during shield construction."

Jan 1, 2016

By V. Shchukin

According to the scientific views formed by the middle of nineteen seventies there should be no possibility of commercial diamondiferous kimberlites in the north of the west European platform. However a later analysis of the geological data gave rise to the concept that diamond bearing kimberlites would be present in the north but on the mineralogical level they would differ from kimberlites of South Africa and Yakutia. Further investigations resulted in the confirmation of these conclusions and with discovery at the beginning of 1980 of diamond bearing kimberlite pipes in the Arkhangelsk region.

Jan 1, 1995

By Daniel Amponsah-Berko, Palas Kamlakar Borkar, Kwabena Boafo, Neha Sharma, Timothy Eisele

A series of iron-leaching experiments were conducted to test the ability of metal-reducing anaerobic organisms to reduce iron from Fe3+ to Fe2+ to dissolve it from iron ore tailings. This bioleaching process involves the fermentation of biomass from Typha latifolia (a common wetland plant) to generate organic compounds, which, along with metal-reducing organisms, reduce and dissolve iron. The concentration of dissolved iron over time was studied for one year. Iron concentration above 1150 mg/L was achieved at a pH range of 3.95–5.36. Tailings from multiple locations were examined.

Feb 1, 2025

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in these two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number.-of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section I of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the antitrust laws is entitled to recover treble damages plus costs.

Jan 1, 1965

By W. W. Kephart

The glass container industry is the largest producer of glass in the United States. As of this writing, there are approximately 89 active domestic production locations. In 1984, the industry shipped 11.8 million tons of glass containers. Approximately 70% of this production was clear or flint glass, 20% amber, 7% green, and the remainder miscellaneous colors. Although the production of nearly 12 million tons of glass is impressive, anyone following the industry over the last five years is aware that the industry has changed from a pattern of growth in the 1970's to one of maturity in the 1980's. Some observers, less generous, perhaps, have described the 1980's as a period of decline. In 1981, there were 119 production facilities which produced 13.2 million tons of glass the previous year. This equates to a 10% reduction in glass container production from 1980 to 1984, with a corresponding impact on the segment of the industrial minerals producers serving the container glass industry, as shown in Figures 1 and 2.

Jan 1, 1986

By Sam S. Arentz

Storm King Mines began with the concept that the resource potential of thick and steeply pitching seams of the Grand Hogback region of Colorado could be mined profitably. Two large tracts of private land (fee coal) were acquired; approximately 23.8 km2 near Glenwood and 16.2 km2 near Meeker. Figure 1. Although both properties have substantial coal reserves, one has several distinct advantages in developing a competitive mining operation. Table 1 illustrates these advantages. Among the most important considerations from an economical point of view are proximity to railroad, highway, labor force, quality of coal, seam thickness, and source of water. As can be seen, Storm King Mines' property is adjacent to the main line of the D & RGW Railroad, 1-70, and the Colorado River. The cities of New Castle, Glenwood Springs, Silt, Rifle, Carbondale, and Parachute are within short commuting distances and have available skilled labor.

Jan 1, 1983

Adsorption experiments were conducted at two different solids loadings, to investigate the mechanism of oleate adsorption on apatite. Adsorption density at pH 10 was found to be dependent on solids loading in an oleate concentration region where surface precipitation could occur. Analysis of adsorption isotherms indicated three distinct regions of adsorption. In the region I (below the region of calcium oleate precipitation), molecular adsorption was observed. Simultaneous molecular adsorption and surface precipitation occurred in region II, while surface precipitation was predominant in region III along with some bulk precipitation. Correlation between flotation of apatite with sodium oleate and the mode of oleate interaction with the surface is established.

Jan 1, 1986

By W. G. Pariseau

"BACKGROUND The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March, 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to begin mining in the south barrier pillar. Subsequent loss of ground control in August, 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterwards three rescue team members. An MSHA report describes the events in detail (MSHA, 2008). An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools; selecting the right tool for the job is essential. In this regard, a minimum program requirement is capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses. The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two dimensional finite element analysis indicated pillar safety was by no means assured (1, 2, 3). Geometry of barrier pillar mining is limited in two-dimensions, for example, crosscuts are not seen in vertical cross sections. While three dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three-dimensions. This technique involves a dual node – dual mesh concept. Both have been used separately in much earlier work, but are only now are used in combination. Estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale are possible (4). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2015

By H. L. Holden

The single line grinding circuit at Bond Gold's Colosseum mine consists of variable speed drive semi-autogenous (SAG) milling and secondary grinding with a fixed speed ball mill. There are several advantages and disadvantages of operating SAG mills with variable speed drives. Discussion in this paper will focus on the effects of variable speed SAG milling in relation to mill liner wear, grinding media consumption, and mill operating availability. Operating experiences, corresponding mill data, and pertinent design changes are also presented.

Jan 1, 1991

By T. S. Golosinski

Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost, and significantly influence dragline productive time. Both work in very difficult conditions and wear out rapidly. As a result frequent rope changes are required at a substantial cost and time loss to the operation. Although performance of rigging has a profound impact on dragline performance, there are no industry-wide standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The life of drag and hoist ropes depends on: (1) rope construction, which should closely match requirements of the specific application, (2) correct definition and application of the rope discard criteria, so that full advantage of the rope can be taken without endangering safety of operation, and (3) rope operating conditions and its maintenance. The study presented in this paper was intended to address the above points, based on a survey and assessment of the present industry practice.

Jan 1, 1993

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By Edmond F. Lawrence

The Calico area lies within the Walker Lane fault zone, six miles north of Schurz, Nevada. The mineralized area is overlain by a thick section of Tertiary tuffs and ash-flows, that have been intruded by a series of andesite plug, dikes, and sills. The pre-Tertiary rocks outcrops only in two areas at one to two miles distance from the drilling areas. Underlying the volcanics are sediments ranging from siltstones, sandstone, calcareous shales, to carbonates of the Luning sequence. These have been intruded by one or more phaneritic intrusives ranging in composition from quartz diorite to quartz monzonite, with the development of a skarn zone on the south flank that contains extensive mineralization consisting of magnetite, pyrrhotite, pyrite, and chalcopytite, with traces of sphalerite, galena, and molybdenite. The magnetite, pyrrhotite, and part of the pyrite appears to be contemporaneous with the skarn, while, part of the chalcopyrite, galena, sphalerite, molybdenite, quartz, and calcite, occurs as minute veinlets cutting the other minerals. This later mineralization may be associated with a late stage of the same sequence, or possibly associated with another intrusive to the southwest. Geophysical work has consisted of aerial magnetics, ground magnetics, gravity, seismic, and induced polarization surveys. Preliminary induced polarization surveys indicated anomalies at depth, both over the magnetic anomaly and to the northwest. Subsequent IP work confirmed this earlier anomaly, and drilling disclosed extensive mineralization at depths of 400 feet on the northwest end and over 1,000 feet to the southeast.

Jan 1, 1967

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984