Search Documents

By J. Iannicelli

An entirely new level of magnetic filtration technology was put into full commercial production by the kaolin industry of Georgia, U.S.A. during 1973-1974. At present, four kaolin producers in Georgia are operating large magnetic filters each capable of processing over 1000 gallons of kaolin slurry per minute or over 65 tons of kaolin per hour on a dry basis. A fifth large filter will go on stream in August, 1975. Four of these units are 84" machines manufactured by the Pacific Electric Motor Company of Oakland, California. When operated at the maximum 1000 g, p. m. rate, these five large magnetic filters have a combined capacity approximating the entire waterwashed coating and filler kaolin produced in the U.S.

Jan 1, 1976

By George S. Austin

Perlite is rhyolitic glass with 2 to 5 percent by weight (wt.%) bound water held within the silicic-glass structure. It is often distinguished by vitreous, pearly luster and concentric perlitic fractures ("onionskin"). Occurrences worldwide are associated with Tertiary to middle Quaternary volcanic rocks. Perlite is in silicic domes, plugs, laccoliths, flows, vitric tephra, chill margins of dikes and sills, and welded ash-flow tuffs. It is a hydrated volcanic glass formed through secondary alteration of obsidian by the incorporation of water into the glass/silica structure. Post-emplacement hydration (weathering) of cooled glasses by meteoric water is the principal alteration process, but some hydration by magmatic or meteoric water during or shortly after emplacement, or hydration by water exsolved during cooling may occur. Commercial "perlite" is any volcanic glass that expands or "pops" when heated quickly to plasticity while evolving steam and thus forming a lightweight, frothy material. The expansion temperature typically ranges from 1,100 to 1,500°F. An expanded volume increase of 10 to 40 times the original volume yields expanded densities of 1.5 to 11 pounds per cubic foot (lbs/ft3). Perlite is mined by eight companies at 10 operations in six western states. New Mexico accounts for more than 80% of the total tonnage mined. The rest comes from Arizona, California, Colorado, Idaho, and Nevada. In 1992, domestic production was 571,000 short tons (st), domestic apparent consumption was 591,000 st, and the value of crude perlite was $15.3 million. In 1991, with about the same production and price of crude perlite, the gross value for expanded perlite was $101.7 million. Perlite exports in 1992, primarily to Canada, are estimated an 30,000 st; and imports, from Greece, are an estimated 50,000 st. In 1992, 70 plants in 33 states expanded crude perlite. Construction uses of expanded perlite accounted for 66% of total domestic sales. Expanded perlite used as filter aid accounted for 15%. All other markets, including use as a filler and in agriculture, accounted for 19%. Leading states for expanding perlite, ranked by order of sales, were Mississippi, Pennsylvania, California, Illinois, and Georgia. Domestic perlite encounters transportation disadvantages in some areas of the eastern United States compared to perlite imported from Greece. However, western U.S. perlite exports to Canada offset this in large part, and net import reliance for perlite is about 3% of domestic consumption. Perlite grab samples were tested at the New Mexico Bureau of Mines and Minerals Resources (NMBMMR) for their basic suitability in horticulture, construction, filter aids, and fillers/extenders using Perlite Institute techniques modified by the NMBMMR. Most commercial perlite ranged from 2.5 to 3.0 wt.% bound water for all major types (classical, granular, and pumiceous). Expanded density varied widely, but the lowest density of 1.9 lbs/ft3 was for granular. Average brightness of expanded perlite was 47.6 to 69.3%. Nonexpansibles, commonly obsidian or "dead" perlite, ranged from 18 wt.% to less than 1 wt.%, with granular perlte generally the lowest. Compacted density was not related to either perlite type or nonexpansibles present. Sieve analyses of the -50+100 mesh product showed that, in general, pumiceous perlite produces more fines and classical and granular perlite average 60 to 80% -30+100 mesh after expansion. Samples were tested for crystalline silica that ranged from below the detection limit of 0.5 wt.% to nearly 0.2 wt.%, but most tested below 0.5 wt.%. Although quartz content can be lowered in the expanded product by the expansion process, producers can further lower crystalline silica in the product by mixing low-quartz crude with high-quartz perlite before expansion. Chemical analysis by x-ray fluorescence confirms the rhyolitic composition of perlite, but indicates that surface weathering may increase the concentration of some elements, such as potassium and calcium, by infilling cracks or fissures developed during or after perlite emplacement.

Jan 1, 1995

By Russell L. Wood

The title of this session seems to have been picked especially for this paper. It is 1984, it is the morning after, and there is one monumental hangover among many if not most of the oil companies that have invested in mining in the past decade or so. How an oil company looks at mining depends on what time period you are talking about. A few years back around the time of investment this is what they were probably looking at: 1. A balance sheet of their own that was beginning to go wild, with many of their commodity prices having already seen increases of two, three, or four fold, and with no end in sight. 2. A need to invest their earnings someplace fast before the stockholders or the government got too interested. And that someplace should be in an industry where their own management skills could be applied. (Only a true cynic would suggest that this is a form of job security) 3. In mining there was an industry amazingly similiar to their own, one working with non-renewable natural resources, dealing with the same types of government agencies, and having the same type of critics and pressures from the general population. 4. An industry that was somewhat backward as compared with their own, and one where a generous ration of the capital and management skills so handsomely bestowed upon the oil industry could be used to great advantage.

Jan 1, 1984

By X. Li, J. C. Stankus, J. Ma, H. Chen

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a slope entry, the problem is more difficult, because a slope will transverse through many types of strata. Over the last few years, Keystone Mining Services LLC, an affiliate company of the Jennmar Corporation, has developed a new methodology designated the “Stress, geologic and support design system (SGS).” The method analyzes the stress, geology and support design for a mine slope. The method has been successfully applied in various new slopes across the United States, and ground control plans developed using SGS methodology has helped coal companies successfully pass review and/or hearings by state and federal regulatory agencies. With a case application in the U.S. Midwest, this paper details and demonstrates the main concepts of the methodology, including (1) analysis of stress and geology and identification of strong, fair and weak zones along the slope; (2) primary and supplemental support design; (3) long-term support design in the form of steel square sets or arches and (4) validation of the support design utilizing advanced finite element computer modeling.

Jan 1, 2011

By Orville D. Mussey

During, 1956 the water used in mining iron ore in the United States amounted to about 2 billion gallons and the water used in producing iron concentrates-amounted to about 166 billion gallons. By 1980 an increase of about 65 percent is anticipated in the amount of water used for mining and beneficiating iron ore. Except for boiler-feed makeup water the quality requirements for water, for mining and beneficiating iron ores are not stringent. Adequate supplies. of water for development should be available at reasonable cost with the possible exception of some in arid regions.

Jan 1, 1961

By Mark E. Emerson

Foreign and domestic companies find the mineral potential of this country's stern public lands, its capital markets, political stability, and "open-door" policy attractive for hard mineral exploration. Traditionally, exploration in the US has been geographically based and responsibility oriented at the district level. The 1970s brought a decentralized approach to exploration as major non-metal companies began to diversify into hard minerals. The emphasis was on capital intensive metal and energy projects involving bulk-tonnages. The recent economic downturn in metals has caused many of the new participants to withdraw from the mineral scene. The surviving companies have shifted their emphasis toward medium scale precious metal projects having high operating margins and rapid return on equity. Exploration expenditures in the United States are now principally focused on gold and silver to the exclusion of practically all other commodities. In the search for precious metals companies have scaled back their exploration efforts and have began to apply new approaches to target selection. The search is being assisted by rapidly evolving conceptual models. The change in orientation has led to numerous new discoveries. The finds are essentially "rediscoveries" that c,-re previously uneconomic. The majority are low-grade surface deposits that have involved low discovery costs and short lead times for development by low-cost mining and beneficiation methods. The emphasis on gold to the exclusion of all other commodities raises questions regarding the direction of exploration in the US for the rest of the 80s.

Jan 1, 1984

By D. Tahija

"Carbonic acid prepared on-site from carbon dioxide gas is widely used in water treatment and increasingly in some industrial applications. It has not seen extensive use in mineral processing but is an attractive alternative to sulphuric acid for pH control, with the need to counteract high pH levels caused by cemented backfill of particular interest. The fundamental chemistry of carbonate solutions as applied to flotation and flocculation circuits is described as well as plant-scale application. A project to introduce use of carbon dioxide for pH control at the Hecla Greens Creek lead-zinc-silver-gold operation is planned to begin operation in the first half of 2015. INTRODUCTION Flotation pH Control and Backfill Most sulphide flotation circuits are run at pH values ranging from slightly acid to strongly basic, with slightly basic pH the most common. Lead sulphide circuits are typically run at values from 7.5 to 9, with zinc circuits running at higher values of 9.5 to 10.5. This has been the case with ores that produce a natural pH in the circumneutral range, so that the pH needs to be raised. Although lime [Ca(OH)2] is the cheapest reagent in use to raise pH, soda ash (Na2CO3) or caustic soda (NaOH) are also employed where sodium ions in solution are preferred to dissolved calcium, or, in the case of soda ash, the presence of carbonate is desired. The use of soda ash for pH control in lead circuits has been widely recommended for many decades (1). The situation is necessarily different at operations where cemented backfill is used in underground mines (2). Backfill, whether emplaced as rammed paste or pumped slurry, is composed of mill tailings mixed with around 10% Portland or similar cement. When later mining occurs near or adjacent to previously backfilled areas, a considerable amount of old backfill is inevitably mixed with new ore and shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed can easily approach 20%, with periods of higher content not unheard of. The presence of so much backfill, with its high cement content, produces results largely indistinguishable from adding a large amount of lime to run-of-mine feed: mill pH in the grinding circuits can range above 11 and high concentrations of calcium ions are present. The need to raise pH disappears; the problem becomes to lower it."

Jan 1, 2015

By Gary D. Aho

The United States on a daily basis no consumes about 15MM barrels (2.38 x 106m3) of oil; 5MM (0.79 x 106 m3) of this is imported. This compares tai a daily consumption of 18MM (2.86 x 106 m3) in 1980 when we imported 8MM (1.27 x 106 m3). We are producing the 10MM barrels (1.59 x 106 m3 ) of conventional oil at home from what amounts to just 2% of our domestic energy reserves. Nearly 90% of our total domestic energy reserves occurs in solid forms such as coal, oil shale, and tar sands; this is more than enough to meet our needs for the next 100 years. Worldwide, oil shale is second only to coal as a potential source of energy and the U.S. has approximately one-half of the world oil shale reserves which average over 25 gallons per ton (10.43 x 10-2 L/kg). Since the United States has immense oil shale resources, including some of the richest in the world, and since oil shale produces a superior transportation fuel, it would seem logical that the U.S. would be prudently developing this domestic resource. Unfortunately, despite over 50 years of research and a number of false starts, there is not a commercial shale oil industry in place today. There are a number of recurring roadblocks which have hindered private industry's efforts to develop oil shale and we will look at some of these.

Jan 1, 1983

By C. W. Chiaretta

Utah Power and Light Company's Deer Creek Mine had been developed to a point where mine ventilation efficiency had declined to an unacceptable level. Problems identified were ventilation of inactive areas, excessive leakage, and restrictions in the return and intake air ways. Mine management implemented an intensive mine ventilation improvement program to alleviate future problems with respirable dust in the working sections and diesel equipment emissions. Program objectives included sealing of inactive areas of the mine, rehabilitation of high resistance areas, and construction of additional intake and return aircourses. Applications of computer modeling techniques are used to predict the effects of ventilation changes and improvements. Improvements are then prioritized to achieve the largest efficiency increases first. Actual real time assessment of the mine environment and ventilation changes are accomplished with a mine wide monitoring computer system. The Deer Creek ventilation improvement program has more than doubled the ventilating efficiency of the mine.

Jan 1, 1990

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

Good morning ladies and gentlemen of the AIME. I was doubly pleased when Toby Yu asked me to present to you my thoughts on the past, the present, and the future of bulk transportation by barge. My first pleasure comes from sharing with you the subject that has been my career for many years. I love this industry in the same way Mark Twain loved our rivers. Somehow, I can find in all of the activities that make up this crazy barge business the same sort of excitement that he found in "steam boating." The second reason for my enthusiasm is that Toby carefully pointed out that the presentation had to be kept to a maximum of 15 minutes. I can promise you that I will hold to his maximum time limit.

Jan 1, 1982

By Paul Nicholas, Raju Gottumukkala

"India’s economy is expanding with rapid urbanization. Improvement in infrastructure is a keystone to the Indian government’s economic plans, including expansion of transit systems. Most of these systems are designed with elevated and underground sections. New Delhi, a city of 23 million people, suffers from heavy traffic congestion and pollution. The transit (metro) system is seen to be of critical importance. Phase 3 of the Delhi transit system project is 140 kilometers (km), with 40 km of twin-bore tunnels requiring 35 tunnel boring machines (TBMs) for construction. Transit systems are also under design or construction in Chennai, Bangalore, Kolkata, Hyderabad, Jaipur and Mumbai. Most have twin-bore tunnels. At present, 55 TBMs are operating on underground metro construction, and future projects will increase this number. This paper highlights the unique challenges of construction of underground metro systems in highly congested urban environments, using Kolkata and Delhi systems as examples. INTRODUCTION The first transit system in India was constructed in Kolkata (India’s third-largest city by population.) This line is 28 kilometers (km) in length, has underground and at-grade sections, was built in phases, runs north/south, and has 24 stations. This project was sanctioned in 1972, started construction in 1984, and was completed in 1995. The tunnels were constructed primarily by cut and cover methods with some open-face, compressed air shield tunneling. In 2006, the urban transport policy recommended construction of transit rail systems in all urban cities with a population exceeding 2 million. Further, in 2014 the central government stated that it would assist in financing transit systems in all cities with a population of over 1 million. In 2015, the central government approved the development of transit systems in 50 additional cities across India with a budget of $75 billion (see Figure 1). Transit development is just part of a huge expansion in planned rapid transport systems, which include metro, bus, high-speed rail, and monorail systems. Metro systems will include elevated and underground sections with twin-bore tunnels and underground stations. In the Delhi/National Capital Region (NCR), now the largest city in India by population, Delhi Metro Rail Corp (DMRC) was formed in 1995 as a joint venture company between the central government and Delhi state. DMRC operates the Delhi metro system. (see the case studies described later in this paper). DMRC has developed an external function to carry out studies and to offer consultancy to other cities planning transits. Since its inception, DMRC has produced Detailed Project Reports (DPRs) for every metro and monorail project in India. In 2012, DMRC became a partner in the management consultancy for Jakarta Mass Rapid Transit System, its first project overseas. DMRC became a model organization for other cities to follow. These cities have included Chennai, Hyderabad, Kolkata, Bangalore, Jaipur, Mumbai, Ahmedabad, and Nagpur. Other cities (e.g., Lucknow and Patna) are in the metro planning phase. Metro systems are under construction or partially operating in Hyderabad, Bangalore, and Jaipur."

Jan 1, 2016

By Mike Wongkaew, Brandon Kluzniak, Per Vilhelmsson

Rail access to Ontario International Airport (ONT) has long been a goal of San Bernardino County Transportation Authority (SBCTA) to increase public transit options to ONT and provide incoming ONT passengers improved access to San Bernardino County and the greater Southern California region. This paper describes the planning for the Design-Build-Operate-Maintain (DBOM) delivery of an emerging technology tunnel connection between the Rancho Cucamonga Metrolink station and ONT. The paper discusses key technical considerations, challenges, and opportunities; conceptual configuration development; and construction planning and establishment of the footprint for the underground connection.

Dec 1, 2022

By Jr. Lownie

Estimates of the cost of producing any commodity generally fall into several classes depending upon the motives and needs of the estimator. There are estimates intended to show how low costs might be with favorable conditions if everything goes well. At the other extreme, there are estimates which show how high costs might be if troubles develop. The estimates in this paper for the cost of producing direct reduced iron (DRI) are accompanied by discussion to point out how the final figures may be adjusted in either a promotional or a conservative direction. Because we do not have a specific process and a particular set of conditions in mind when discussing this subject today, this paper deals with the general situation, with considerable attention to how the estimates can be made more specific once one knows the particulars of a given situation.

Jan 1, 1978

By Tomás Vergara, Marcelo Vergara, Alonso Pereira, Fernando Concha, María V. Gutiérrez, Fernando Betancourt

Filtration of copper concentrates in the mining industry is carried out in cycles, mainly cake formation, expression, and blowing. Each of these cycles depends on the solid (mineralogy, porosity, particle size distribution), water, and air (density, viscosity, permeability, and relative permeability) properties that define the performance in each cycle. The fundamental phenomenon in cake formation and expression is a one-phase flow (water) through a porous bed of solid particles (the cake), while in blowing it is a two-phase flow (water and air) through the cake. Sometimes, due to a change in the properties of the mineral, a filtration plant is unable to maintain the capacity at the specified humidity. One alternative to solve this problem is to heat the air during the blowing cycle, which in turn heats the water in the cake, this process significantly decreases the water viscosity and only marginally increases the air viscosity. In this work, this strategy was studied at a laboratory scale. The results show a significant decrease in the blowing time as the temperature of the air was increased.

May 24, 2022

Mine design and selection of ore processing capacity depend upon a correct estimate of the grade-tonnage distribution. The estimate must reflect what can be recovered and processed. The McCoy/Cove operation in central Nevada, USA, is a gold and silver mine. Case studies of recoverable reserve estimation for gold and silver were made using multiple indicator kriging and the log-affine variance correction. From this model, the grade-tonnage distribution was constructed. Optimal pits were generated by utilizing the distribution, and the results were compared with the pit generated by ordinary kriging. Studies indicate that the proposed method for multi-metal recoverable reserve estimation is more accurate than ordinary kriging in terms of both tons and the grade. Using recoverable reserves for mine design will maximize global recovery of mineral resources.

Jan 1, 1997

By Henry R. Colen

When we were asked to prepare a paper on gold to be part of the Economics of Precious Metals session, our immediate thought was that we should address the question of supply. Are the existing mines of the world capable of filling the demand for gold? We recognized that gold does not conform to the normal pressures of supply and demand. Major new sources of production and increased sales might have a very short term effect and depress the price but this does not last very long. Those forces that affect gold prices are very different from the ones economists normally deal with. Factors such as mass psychology, political tensions and fear are certainly more important to the gold price than supply and demand in today's world.

Jan 1, 1981

By K. Lapakko

Kinetic tests results are influenced by methodological variables, including test duration and mine waste particle size. Some samples tested produced neutral drainage in kinetic tests for more than two years prior to drainage acidification. The potential for long "lag times" can be assessed based on the mine waste mineralogy. The lag time duration can be estimated using this mineralogy in conjunction with dissolution rates observed in the kinetic tests. The influence of particle size on the drainage quality is dependent on the variation of the availability of acid-producing and acid-neutralizing minerals with particle size.

Jan 1, 1998

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019

By Lauren W. Choate

Wollastonite, a calcium metasilicate, derives its name from the man who discovered the mineral, Doctor William H. Wollaston, an English scientist. OCCURENCE Occurences of the mineral have been noted in Finland, Switzerland, Russia, Japan, Mexico and in the United States in Texas, California, Arizona, and New York. The only commercial deposit now being exploited is at Willsboro, New York. It is mined and processed by the Cabot Corporation whose home offices are in Boston, Massachusetts.

Jan 1, 1964