Search Documents

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By G. F. Revey

Most commercial explosives contain 70 to 94% ammonium nitrate, by weight. When portions of these explosives end up in shot rock and ore, through spillage or incomplete detonation, ammonia and nitrates leach out of them and into ground water. In recent years, State and Federal regulators have been applying more stringent water quality standards, particularly at new mines and development projects. Bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice at most mines, when mining conditions allow it. ANFO use is desired because it less costly than other explosives, but when spilled it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. They either control explosive losses, or they treat mine effluents at the end-of-pipe. This paper addresses the former solution --controlling explosive losses. For both packaged and bulk explosives, guidelines designed to limit losses during storage, handling and use, are described in detail.

Jan 1, 1995

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By Emmanuel V. Manlapig

The variables involved in a complex process like flotation can be classified as follows: a. Disturbance variables - which are undesired properties of the process input which affect the value of the process output but which are not subject to adjustment. They are the result of changes in the properties of the feed, like changes in head grade, flow rate, fineness of grind, etc. b. Manipulated variables (sometimes referred to as process variables or control variables) -which are those that are adjusted - reagent addition, aeration, pulp level - in order to compensate for the disturbances in the properties of feed. c. Performance variables (sometimes referred to as controlled variables) -which are those whose values measure the performance of the process. They are properties of the process output such as grade and recovery. The function of a control system is to maintain the process performance equal to the control objective in spite of the disturbances by adjusting the manipulated variables. Attempts at developing automatic control systems for mineral processing operations date back to the thirties and in many of these attempts the results were not surprisingly poor and un-stable. The poor results brought indifference and suspicion towards automatic control on the part of operators and management. The reasons for the apparent failure of these attempts were two-fold: a. the lack of adequate understanding of the behavioural responses of the process from the control point of view, and b. the lack of reliable control instrumentation which could withstand the harsh environment in mineral dressing plants. Many operators had accepted the fact that control of mineral dressing could be best conducted manually. In the case of flotation circuits, control had been virtually based on the skill and experience of operators particularly their ability to identify and rectify poor flotation performance aided by results from the laboratory (chemical) analysis of regularly collected samples from strategic points in the circuit which are at best, hourly collected samples.

Jan 1, 1978

By Reul A. Dejú

The mineral olivine has been the subject of continued research by various authors. Paik (1967) conducted infrared and flotation studies of the adsorption of sodium alkyl benzene sulfonates on olivine. These studies are of interest from two points of view. First, in the metallurgical field it is of interest to understand the mechanism of silicate flotation using sulfonate collectors and second to a hydrologist studying the pollution of surface or subsurface waters it is of interest to study the reactions taking place when water plus sulfonates encounter a porous (silicate) medium. On the basis of Paik's study he was able to postulate a possible mechanism for the attachment of RSO3 (sulfonate radical) to the olivine surface. Parks (1969) has been studying the important influence of the structure of a silicate such as olivine on its dissolution mechanism and its related surface charge. Also Luce, a student of Parks (1964, 1965) has been studying the kinetics of dissolution of olivine using the techniques of direct solution analysis and infrared analysis. Certainly a classic in the study of silicate dissolution is the work of Murata (1940) on the reaction of orthosilicates (olivine in particular) with strong acid solutions. Many authors (Dejú and Bhappu, 1966. 1967. 1968, Dejú, 1969; Rhoades and Krueger. 1968, and Faust and blunter, 1967) have reported studies of the behavior of silicates immersed in water (especially orthosilicates) and have found that there is an exchange of cations from the silicate surface for H+ from the water. Studies by Dejú and Bhappu have also included the system olivine-water-amine.

Jan 1, 1971

By P. M. Krishna

A five-year effort by the ASTM subcommittee E10.14 on Uranium Resource Evaluation has culminated in the approval of E901-82, Classification System for Uranium Resources. The standard classification was prepared with participation of representatives from the Dept. of Energy, the Dept. of Interior's Geological Survey and Bureau of Mines, utilities, and consultants. The classification of a resource is based on level of knowledge and the economic producibility of the resource at a given time. Alpha-numeric identifiers are used rather than words to avoid confusion with existing terms, definitions, and classifications. An effort is underway to develop estimation criteria to guide users in classifying a resource according to the above format.

Jan 1, 1983

By Edward T. Koch

With the dramatic increase in world demand for basic raw materials, open pit mining is proceeding at an unprecedented rate. A viable demand is the ever tempting Siren's song for increased production or new facilities. When the Siren's lure is viewed against the panorama of today's world economic milieu the concomitant Scylla and Charybdis are seen in the form of high capital cost and high operating cost. If the economic realities of present day open pit mining are to show a proper return on investment, a clear and penetrating eye must be cast upon the area of mine planning. This paper deals with the problem of overburden removal. In almost every open pit mining operation overburden removal is a significant part of the capital cost and operating cost of the total operation. This paper deals with a new and unique method to affect economical overburden removal. Well known to all are the parameters surrounding draglines, shovels, and bucket wheel excavators. All of these machines require a reasonably stable soil to support them and the shovel and bucket wheel excavator require a reasonably stable bank in which to operate. Their reliability, portability and rate of production per dollar of invested capital are good.

Jan 1, 1975

By R. H. Parker, B. A. Wills, D. G. Binns

Introduction With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the fine mineral particles in these ores. Not only is this expensive, but it leads to greater losses in slimes. Gravity concentration techniques become unacceptably inefficient for particle treatment below 25 to 50 µm, and even flotation fails in the ultra-fine range. Ore from the South Crofty mine near Redruth, Cornwall, was subjected to thermal pretreatment in the hope that differential thermal expansion of the minerals would lead to intergranular cracking, and thus enhanced liberation. South Crofty ore contains about 1% tin as cassiterite associated with a complex assemblage of quartz, chlorite, tourmaline, and hema¬tite in granite and slate. Recovery of cassiterite can be as low as 70%, as overgrinding occurs during stage reduction of the material to 1 mm (primary grinding) and 180 µm (regrinding). Cassiterite is present in grain sizes ranging from submicroscopic to + 10 mm, the bulk being predominantly in the range of 50 µm to 3 mm. Experimental Flat polished sections of the ore were photographed in reflected light using a Vickers M17 microscope. The sections were then heated in a Carbolite LMF4 muffle furnace. The heating rate and temperature were monitored by a thermocouple immersed in the bed of particles. Previous work by Sherring (1981) on the same material showed that a 55% reduction in grinding resistance occurred when the material was rapidly heated and cooled through the quartz inversion tem¬perature (573°C), where a volumetric expansion of 0.86% occurs. The samples were therefore heated to 650°C at 26°/min, and were then water-quenched to room temperature. The effect of heat treatment on the mineralogy and fracture network was assessed by examining the same area after treatment. Results Most of the sections examined showed that extensive transgranular cracking occurred as a result of heat treatment. Such cracking, although weakening the rock and hence reducing the work index, would in no way enhance the liberation of the cassiterite from the host minerals. Intergranular cracking, which would lead to enhanced liberation, was difficult to discern under reflected light, but there was evidence of such cracking in some of the sections examined. Figures 1 and 2 are examples of typical sections before and after heat treatment. Figures la and lb - show cassiterite in hematite, Fig. lb, in normal incident illumination, illustrating clearly that after heat treatment, transgranular fracture is evident in the cassiterite. If any intergranular cracking has occurred, it is not evident in this photograph. Figures 2a and 2b show cassiterite in quartz before and after treatment. Fracturing in both minerals after treatment can clearly be seen, and there is evidence of intergranular fracturing. However, protruding "arms" of cassiterite are severed by transgranular fracture. Subgrains of quartz have also been isolated by trans¬granular fracture. There is major transgranular cracking across the wider sections of cassiterite. Discussion The effect of rapidly heating South Crofty tin ore to 650°C, followed by water-quenching to room temperature, has been studied by observing the fracture networks in mineral grains. The choice of 650°C as the heating temperature was influenced by the work of Sherring (1981), who found considerable reduction in grinding resistance after thermal pretreatment of the same ore. Scheding et al. (1981), however, have shown, by means of a crude calculation, that heat treatment cannot be justified solely on the basis of reduced grinding costs. The cost of heat treatment far out-weighs that of grinding, resulting in the combined costs for heat treatment being over six times that for grinding unheated material. The most economically attractive aspect of heat treatment is the possibility of enhanced liberation of the valuable mineral due to increased intergranular rather than transgranular fracture. Grinding costs would be greatly reduced by improved liberation at coarser sizes, and the costs of ancillary processes, such as dewatering and tailings disposal, would be reduced. The most significant economic effect, however, would be in improved metallurgical efficiency. Improved liberation would increase concentrate grades, and recoveries would be higher, particularly in the case of ores where high slime losses are produced due to the excessively fine grinding required to produce adequate liberation. Manser (1983) has shown that only a 1% increase in tin recovery, at the same concentrate grade, would be sufficient to offset heat treatment costs on South Crofty ore. Heavy liquid analysis and shaking table separation have been used to evaluate the effect of thermal treatment on processing (Binns, 1984; Scheding, 1981; Sherring, 1981). However, treatment of unheated and heated samples of South Crofty ore, ground to the same product size, by such methods have shown little evidence of improved metallurgical efficiency after thermal pretreatment. The large amount of transgranular fracturing revealed by reflected light studies helps to explain this lack of improvement. Nevertheless, from the evidence of some of the fracture work, it is surprising that no improvements in metallurgical

Jan 1, 1988

By C. J. Monahan

INTRODUCTION With the introduction of large diameter hole drilling to underground mining, a need for the development and utilization of new blasting technology has arisen. This new technology has resulted in more efficient blasting and in easier and cheaper mining. The application of spherical charges to the crater blasting method is an im¬portant part of this technology. Spherical charges, or their geometric equivalent, make for highly efficient use of explosives in the cratering application. Their geo¬metrical configuration, normally a length :diameter ra¬tio of <6:1, limits their charge weight size. For exam¬ple in a 165-mm (61/2-in.) hole a spherical charge weighs approximately 34 kg (75 lb). These dimensional and weight restrictions require careful engineering design and control in the production application. Strathcona mine, a large tonnage mechanized cut¬and-fill and blasthole stoping operation located on the north rim of the Sudbury Basin, has successfully em¬ployed the crater blasting method in production blasting for the past two and a half years (as of 1979). As a result, this method, using spherical charges, has made possible the development and implementation of a verti¬cal retreat blasthole mining method which is being used for rib pillar recovery. The crater method used at Strathcona essentially in¬volves blasting off horizontal slices of ore into an under¬cut while retreating vertically to the pillar overcut elevation. Loading and priming of the holes is achieved from the overcut and the blasted muck is recovered by load¬haul-dump (LHD) units through a drawpoint system. Valuable experience on the behavior and performance of explosives in large diameter holes has been gained in both the operating and engineering fields from the appli¬cation of this blasting method. It has been used in drop raising and is currently being evaluated for use in pri¬mary stoping operations. Also, serious consideration is being given to its use for the recovery of post pillars in mined-out and backfilled cut and fill stopes. The method has significant advantages over conven¬tional methods of pillar recovery from economic, ground control, and safety points of view. These include cost benefits due to a minimum stoping development, less ground support, reduced labor requirements, and faster mining rate. Research on the blasting mechanism indi¬cated the method should result in less damage to fill walls than would be normally expected with conven¬tional longhole or large diameter hole cylindrical blast¬ing (benching). This is primarily due to the limited charge weight per delay because of the size dimensions of a spherical as compared with a cylindrical charge and also because the large diameter holes experience less de¬viation than standard-sized longholes. Experience has shown that wall damage has been minimized with the use of this method. The safety aspects of the working environment are also improved as there is no require¬ment for manpower to go under exposed backs after blasting, which is a significant improvement over the cut-and-fill method. CRATERING THEORY General The term cratering, in blasting, is applied to the for¬mation of a surface cavity in a material as the result of detonating an explosive charge in that material. This blasting concept was initially used as a tool in the eval¬uation of explosives performance; however, it has been utilized more recently on surface and to a lesser extent in underground blasting operations. Explosive charges used in crater method are nor¬mally spherical or the geometric equivalent, as research into the application of this breakage mechanism to rock indicates that spherical charges or their equivalent pro¬duce optimum results. In blasting practice, spherical charges have been defined as having a length to diameter (L: D) ratio of 4:1 or less, and up to, but not exceeding a L: D = 6:1. Thus, for holes 165 mm (61/2 in.) diam, a charge 165 mm (61/2 in.) diam, and 990 mm (39 in.) in length would constitute a spherical charge. Crater Testing Crater testing for underground application is nor¬mally accomplished by drilling smaller than production sized horizontal holes into drift walls, placing relatively small charges of explosives in the holes at various depths of burial, firing the charges, and measuring the results. The results are scaled to develop charge weight size and depth of burial parameters for production hole sizes. In theory, this procedure is valid and is appli¬cable for surface blasting; however, in underground applications where the craters are inverted, there is some question as to whether extrapolation of the test results is appropriate. As well as the fact that craters are in¬verted with resultant gravity stresses, testing is often done in a waste rock drift where the properties differ from those in ore rock. There is also some question as to whether a 51 or 76-mm (2 or 3-in.) diam charge behaves similarly to a 165-mm (61/2-in.) charge in a confined borehole. Crater testing at Strathcona involved drilling 76-mm (3-in.) diam holes at various depths ranging from 1 to 3 m (3 to 10 ft). The test holes were drilled in the wall of a predominately waste drift as well as in a stope wall. Charges were placed at various depths of burial, were confined, fired, and the results measured. Although the results were somewhat erratic, possibly because of the aforementioned reasons, they did provide guidelines for basic design for production application. MINING METHOD APPLICATION FOR PILLAR RECOVERY Following initial crater testing, assessment, and tech¬nical evaluation, it was decided to use this blasting tech¬nique in a production application, and to incorporate

Jan 1, 1982

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By James O. Mawyer

Fuel is a major .cost for power generating utilities. Virginia Power is completing one of the nation&apos;s largest coal reconversion programs. As a result, 10 million tons of coal will now be used at six generating stations. Four of these stations are located on naviagable waterways. They consume over half of Virginia Power&apos;s coal. Historically, railroads have exclusively served these plants. In an effort to substantially reduce fuel cost, Virginia Power has reexamined transportation logistics and is proceeding with barge delivery. A phased approach was used by Virginia Power for the transportation program. Plant requirements were first identified. Coal sourcing issues were then examined. The concept of intermodal transportation was investigated. The bottom line cost savings was used as the criteria for continuing the project. The results thus far have been gratifying. Virginia Power has begun to implement barge transportation.

Jan 1, 1986

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry&apos;s future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author&apos;s experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

By D. J. Gurtler

On January I, 1988, Chino Mines Company initiated the use of a system of economic splits for all materials encountered in mining. All mined material is evaluated as mill ore, solvent extraction-electrowinning plant feed and non-ore material to determine its disposition. Post-implementation studies indicate that a significant increase in financial returns on material mined was realized when compared with the copper cut-off grade previously in use.

Jan 1, 1990

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By I. S. Parrish

As noted by McKinstry (1948), "How to deal with erratic high samples is one of the knottiest problems in ore estimation." He described a variety of approaches and methods to alleviate the problem through the averaging and weighing of assay data and by "cutting" or "clipping" of the erratic assays. Bird (1991) elaborated on ways of dealing with the nugget effect (erratics). He listed several procedures for cutting. Bird&apos;s list has been reproduced and/or added to by several authors including Vallee (1992) and Stone and Dunn (1993). Missing from each of these otherwise excellent reviews is a definition, description or guideline to recognition of an "erratic," or just where or when cutting is warranted or justified.

Jan 1, 1997

By G. A. Nyamekye

Two major Inco matte constituents, chalcocite and heazlewoodite, are separated by differential flotation with diphenylguanidine as collector. A new reagent system involving the use of dextrin as a modifying agent which provides better selectivity has been studied for the last three years. Adsorption tests reveal that while dextrin exhibits high affinity towards heazlewoodite, the adsorption isotherm for dextrin on chalcocite shows only weak interactions. Our electrokinetic measurements confirm such conclusions. Since dextrin interaction with solid surfaces seems to be especially strong when such surfaces are covered by hydroxide layer, our electrokinetic measurements are in line with other researchers&apos; findings who postulated that copper hydroxide is not a stable product on the surface of copper sulphides.

Jan 1, 1992

By K. G. Black

When one&apos;s attention moves from the control of a process unit or from the control of a department of similar units, to the control of an entire plant, two things must change. One is the techniques of control, and the other, the goal or purpose of control. The goal is no longer maintaining a certain quality of product or maintaining a particular flow rate through a process unit. The goal becomes economic - how to make the most money out of the plant. The principal control techniques become those of optimizing, rather than regulating. It is quite common to discuss the control of an entire plant in terms of three levels of control l; regulation, supervision, and optimization. Regulation is the control of inputs to a process unit at desired values. This is accomplished by two or three mode analog controllers or DDC loops. The second level of control is the selection of these desired values, e.g., set-points of the regulation controllers. The third level is to make such adjustments or corrections to the supervisory calculations so as to optimize the plant profit. It is immediately evident that supervisory control and optimizing control are intimately related, and a distinct dividing line cannot always be drawn between the two. Some authors prefer to add even more levels such as adaptive control and management information systems, but we believe our point is well made without further division of the functions which are necessary for complete plant control. To accomplish the economic goal, that is, the optimizing (maximizing) of the profit of a mineral processing plant, the plant should ideally be operated as if it were a separate company, buying its raw materials on the open market and selling its products on the open market. While petrochemical plants endeavor to operate in that manner, unfortunately this is not true of a mineral processing plant. The plant manager has to accept the amount and quality of ore the mining department delivers to him, and the products (concentrates) are delivered to another department of the company for further refining. In some cases he may sell

Jan 1, 1972

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990