Search Documents

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

Occupational exposures to respirable dust and submicrometer aerosols emitted by diesel-powered equipment are a health concern for underground mining operators and regulators. A study was conducted in an underground mine with the objective to identify, characterize and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. 

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

By Laszlo Valentyik

The wide scale acceptance of the heavy media separation is due to its simplicity and efficiency. The two most important variables of the process are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media solids. The almost always present clay in the feed and conse¬quently in the medium acts as a stabilizing agent, and its optimum concentration varied between 3-4%.(1,2) Since polymers essentially perform the same function in oil well drilling muds - i.e. to suspend cuttings during drilling - as the fine clay in heavy media separation, this led to the investigation of whether polymers could be used in heavy media separation as supporting agents. During the first phase of the work, it was found that by the controlled addition of polymers, the stability of the heavy media increased without unduly increasing viscosity of the suspensions, thus yielding conditions for more effective and efficient separation. The results of the experiments were reported in a paper at the AIME Centennial Annual Meeting, March 1971.(3) This paper presents the results of the experiment carried out during the second phase of the work.

Jan 1, 1975

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By Donald R. Williamson

The Cyprus Pima Mining Company's open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. At that tine reserves were law - volume (+10 million tons) and high grade (+1.5% Cu). Several periods of growth have brought the operation to its present production level of 55,000 tons per day of ore and +125,000 tons of waste. Over the years, a number of attempts to refine and polish the ore reserve figures have been made using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Other refinements were tried using adaptations of established methods combined with computer modeling techniques. The resulting mine-model ore blocks were an improvement but they still tended to show too match tonnage of mill feed, often at too low a grade. One attempt at Kriging had only limited success. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons thus far between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results. A new, better procedure for estimation of ore reserves apparently has been developed for the Cyprus Pima deposits. The specific procedures seem likely to have direct application to other, similar operations. The methods used to develop the procedures could be of value to still other operations.

Jan 1, 1976

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By J. Klemenic

This paper presents an analysis of gold production and prices over an extended period. Production patterns are provided for the world as a whole and for the five major producing countries. Gold prices as a function of interest rates, as measured by municipal bond rates, are given for the period 1947 to the present. World gold production has had a phenomenal increase since 1980, with the exception of South Africa, all major producing nations participated in this increase, even though the price of gold generally has been decreasing since the high level attained in 1980.

Jan 1, 1993

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources, and resistors. An analogous approach is outlined here for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The modeling technique proposed uses five basic (non-reducible) elements: the H element, the Q element, the D element, the R element, and the N element. These elements are characterized by their (a) pressure gain or loss, (b) air quantity, and (c) pressure-versus-quantity relationship, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine ventilation networks.

Jan 1, 1996

By J. Seiter

Mining has always been among the most hazardous of occupations, and with the increasing demand for coal and minerals, safety in mines assumes even greater importance. Worldwide, underground miners are being exposed to noise and respirable dust hazards associated with roof bolt drilling. These hazards are now being understood to cause irreparable damage to the health of miners. The objective of this research was to discover if a Polycrystalline Diamond Cutter (PDC) drill bit generates less respirable dust and hazardous noise than a competing Tungsten Carbide (WC) bit, in dry vacuum drilling. In order to control the drill parameters the drilling tests have been conducted in a laboratory setting. The results were met by determining the quantities of dust and noise generated using each drill bit and analyzing those levels by using monitoring devices and software to collect the data. This paper includes information on experiment setup, equipment used, drilling parameters, and data collected. The test results suggest that there are noticeable trends that the PDC bits produce less dust than WC bits but more testing is needed to substantiate these trends.

Feb 23, 2014

By Charles A. Beasley

Increased technical and legislative analysis by all parties of interest could result in more efficientand better directed regulatory legislation in the mining industry. Efforts to forestall or frustrate legislation through massive lobbying and public relations efforts are seldom effective over time and often lead to more stringent and far reaching legislation than necessary. The Federal Coal Mine Health and Safety Act of 1969 is perhaps an outstanding example of such insufficiences; a future example may well be regulatory surface mine legislation. Although a lack of extensive hard data seldom enables rapid or sophisticated analysis early in the legislative process, even preliminary analysis may be sufficient. Simple statistical analyses of available data, assessment of the legislative rationale, and subjective appraisal of other non-quantifiable constraints to improved mine safety. An average of 115 underground fatalities at an exposure frequency rate of 0.67 can be reasonably expected in the immediate future, under existing levels of technology, degree of regulation, and economic conditions. If gross unrefined estimates of 6 preparation plant, 5 surface, and 30 strip mining fatalities are assumed, the total fatality industry level could be expected to approximate 156 Serious professional, economic, and technical constraints within the the industry probably preclude any major decrease of these accident levels within the near future

Jan 1, 1972

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Jan 1, 1997

By G. J. Karabin

The Boundary Element Method of Numerical Modeling has become an increasingly popular rock mechanics -mine design tool. It has been used by the Roof Control Division, Pittsburgh Safety and Health Technology Center, MSHA, to aid in the resolution of complex ground control problems since 1985. This paper will present an overview of an evolving simulation process and details of methods utilized to generate necessary coal, rock and gob input properties. Also included is a description of a Deterioration Index System that is used to link model output to observed mine conditions and two case studies to illustrate that process.

Jan 1, 1995

By W. R. Reed, J. P. Rider

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a medium-sized surface blasthole drill shroud with a dry dust collector system. CFD models were constructed in ANSYS FLUENT Version 15. Previously run experiments conducted in the NIOSH full-scale drill shroud laboratory were utilized to validate the models. The setup values in CFD models were calculated using experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for test scenarios, including 0.14 m3/s (300 cfm) bailing airflow with 2:1, 3:1, and 4:1 dust collector-to-bailing airflow ratios and 0.24 m3/s (500 cfm) bailing airflow cases with 2:1, 3:1 and 4:1 dust collector-to-bailing airflow ratios. For the 2:1 and 3:1 ratios, results showed the calculated dust concentrations from the CFD models were within the 95% confidence intervals of the lab experimental dust concentrations. This paper describes the methodology used to develop the CFD models, to calculate the model dust input, and to validate the models based on experimental data. Problem regions were identified and revealed by the simulation of a dry dust collector system. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. INTRODUCTION In surface mines, production drilling is an essential process in blasting which fractures the hard rock overburden for removal. Holes with a predetermined pattern, diameter, and depth are drilled into the overburden to introduce explosives. During the drilling process, considerable amounts of respirable dust are produced. Past research conducting area sampling at blasthole drills has documented time-weighted average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 [1] and 1.04 to 52.30 mg/m3 [2]. These high dust concentrations, which may contain silica, can lead to respirable dust over-exposures for the drill operator, drill helper, and other personnel in the vicinity. These over-exposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal. In order to prevent the development of silicosis to mine workers, the Mine Safety and Health Administration (MSHA) regulates the exposure to respirable dust. For metal/nonmetal (M/NM) mines, MSHA has adopted the threshold limit values recommended in 1973 by the American Conference of Governmental Industrial Hygienists (ACGIH) [3]. The total airborne dust standard is 10 mg/m3. However, if the sample contains greater than 1 percent quartz (the most common form of crystalline silica), a respirable dust standard is calculated with the following equation: Respirable dust standard = (10 mg/m3) / (% respirable quartz + 2)"

Jan 1, 2016

By H. E. Wyslouzil

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favoured for this service due to the low capital and operating cost of the equipment, as well as improved metallurgical performance when compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1993

By V. T. McLemore

The Steeple Rock district is a major epithermal .gold-silver district in New Mexico that exhibits district zoning. Five types of ore deposits occur in the district. The base-metal veins (with Au and Ag) form the center of the district and occur along the Carlisle fault. The gold-silver veins occur along northwest-trending faults outward from the base-metal veins. The margins of the district are formed by copper-silver, fluorite, and manganese veins. In addition, areas of older acid-sulfate alteration occur throughout the district and also exhibit zoning: massive silica/chert zone (inner), silicified zone, and clay zone (outer). This alteration overlies regional; alkali-chloride (propylitic to argillic to sericitic) alteration. Synthesis of available data suggests the acid-sulfate alteration is related to a shallow but older epithermal hot springs system. Subsequently, younger epithermal veins formed along faults.

Jan 1, 1994

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By Keith Olson

In the heart of Appalachia, where coal mining has shaped communities and economies for generations, Bluefield State University (BSU) has made a landmark decision to reestablish its mining engineering technology program. This move comes at a critical juncture for both the university and the mining industry, which faces significant workforce challenges amid evolving technological demands and an aging professional demographic. The program’s revival represents an educational initiative and a strategic response to industry needs and regional economic development. Nestled in the mountains of southern West Virginia, BSU has a storied history intertwined with the region’s mining heritage. The institution’s decision to bring back this specialized program after a hiatus of several years signals a renewed commitment to serving both regional industry demands and providing career pathways for students in an area where the cyclical nature of resource extraction economies has often limited economic opportunities. “This program’s return reflects our deep understanding of this region’s needs and our commitment to preparing graduates for meaningful careers that support our local industries,” said Darrin Martin, president of Bluefield State University. “We’re bridging the gap between education and industry with a modernized curriculum that addresses today’s mining challenges while preparing for tomorrow’s innovations.”

Jun 1, 2025