Search Documents

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By Marlies Grimmer, Frank Amo Boateng

One of the challenges of mining is the concentration of heavy metals it releases into the environment through a phenomenon called Acid Mine Drainage. Freiberg is no exception due to its long mining activities. The European Union proposes that all rivers and streams must be in a good ecological status by the year 2027 but this would be difficult for large water sources as it would be economically unviable. Consequently, the approach of treating these waters at point sources would be of immense help and hence this column experiment on mine water treatment with carbon sorbents to remove zinc form the Rothschönberger Stolln. For this experiment three resins namely, APTsorb, activated coke, charred fermentation residues (which was produced by the Freiberg University of Mining and Technology) were analyzed through a simple column experiment to determine their sorption capacities. Through their sorption capacity as this experiment seeks to ascertain: we are able to make suggestions scientifically on the best material among the three for the future design of a treatment plant for the RSS. After the experiment whereby a 10 ml peri glass column was used, material A: APTsorb showed the least adsorption capacity (0.01 meq/g) and this could be attributed to the fact that the resin works well under pre-determined parameters such as pH and surface area. Material B: Activated coke showed a better sorption capacity (0.53 meq/g) in comparison to the basis value used for this experiment. Material C: charred fermentation residue which was produced by the University showed the most efficient capacity of (1.69 meq/g). This in comparison with the value used as the basis for this experiment showed that material C (charred fermentation residue) is very efficient for zinc sorption. pH values measured at the effluent of all the experiment were slightly higher than the pH measured in the initiating water.

Feb 1, 2024

By J. Gustavson, E. Mallard, F. Pirkle

The Sales Comparison Approach to estimating the value of a mineral property must always be attempted1 . In addition to other parameters, the approach depends heavily on the availability of transaction data. The consideration for the mineral property must be in form of cash, cash equivalent or other consideration. In other words, “What dollar amount did the property sell for?” Mineral properties are generally real estate, albeit frequently buried deeply under the overlying surface real estate, unless the property may be a quarry. In some states, transactions must be recorded in county courthouses, and the sale consideration must be included. In such cases, the appraiser’s job is made easy. In other locations, the sale considerations are withheld in the courthouse data; but occasionally a local transfer tax is collected and recorded. Again, the appraiser’s job is made easy by back calculation with knowledge of the legislated transfer tax percentage. The worst problem occurs when the consideration for a mineral real estate sale is totally withheld. That may occur in so-called nondisclosure states. A recent map2 of ten non-disclosure states in red is shown below. For the full color code, please refer to the footnote

Mar 2, 2022

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By J-P Franzidis, M. C. Harris

Increasing costs, falling grades and a low gold price have caused severe problems for many of South Africa's gold mines. The need to maximise efficiency is extremely urgent. This paper describes the use of column flotation cell s to scavenge significant quantities of additional gold from flotation plant residues; in particular, very fine particles of free gold not recovered by conventional flotation. Experimental gold- specific collectors enhanced gold recovery significantly. The paper also reports the results of other plant trials, carried out on a variety of ores.

Jan 1, 1991

By M. A. Qianjie

The problems of coalmine safety in china remain unsolved for decades. Starting with the description on safety status quo of coalmine in china, different existing analysis and measures discussed for the safety problem solution of coalmine china. With the consideration of system thought in mind, the author present with a unique systematic reason analysis method on such actuality--individual analysis and general analysis--each for its particular purpose. Upon such cause analysis, construction of the safety system is made clear and, solutions for such problems provided.

Jan 1, 2006

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By G. Schriever, H. Thiel, E. J. Foell

A long-term, large-scale, disturbance-recolonization experiment with relevance to the environmental effects of deep seabed mining is described. The study is funded by the German government and was launched in the abyssal eastern tropical South Pacific Ocean in February-March, 1989. After obtaining pre-impact baseline environmental data, a 10.8 km2 (4.2 sq miles) circular area of seafloor was disturbed using a specially designed "plow-harrow" device. An initial post-impact sampling series was carried out immediately after disturbance followed by a second post-impact sampling series six months after the disturbance. Plans call for repeated visits to the site at two year intervals to monitor the anticipated slow recolonization process until the area is inhabited by a new, stabilized community.

Jan 1, 1993

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to-float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in the processing of porphyry ores and treatment methods to overcome the specific problems. Though some of the problems are interrelated the problems have been classified into three broad catagories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1984

By A. Bruynesteyn

The results of a 2 phase evaluation program designed to determine the amenability of an oxide ore from the Butte, Montana mine of the Anaconda Company to a sulfuric acid leach is presented. In the phase 1 preliminary evaluation, using roll tests and percolation leaching in small columns, it is shown that the ore is highly extractable at low acid consumption ratios. In the phase 2 confirmatory tests in large columns on l-l.5 tons of material, the amenability of the ore to the leaching process is proven and pregnant solution grade profiles from planned commercial heaps established.

Jan 1, 1978

By Wen Lan Chen

In the plant where the 800m diameter cyclone was tested, 500 STPH of 50m x 0 raw coal was pulped in a heavy medium tank and pumped originally to four 700mm heavy medium cyclones. For the test one of these units was replaced by an 800mm diameter cyclone with the subsequent feed pressure for both units sets at approximately 15.0 psi. Since this was a feed to zero plant, an appropriate bleed of heavy medium to the dilute medium circuit was established to en- sure that the cleaning of the 500m x 0.5mm raw coal would not be adversely affected by high levels of 0.5mm x 0 fine coal present in the heavy medium. The medium gravity measured varied between 1.41 and 1.43. During a three-hour test on June 10, 1983, the raw coal sample was collected from the feed belt while the clean coal and refuse samples were collected separately at proper locations along the product streams of the two different diameter cyclones. All of these samples were shipped to the laboratory for screen and sink- float analyses. The raw coal screen and ash analyses are shown in Table 1.

Jan 1, 1984

By J. Hanna, R. Kalathur

Over the years, Alabama's coal industry has generated, during mining and cleaning operations, about 150 million st of fine waste coal, with this total increasing at a rate of 2 million stpy. Reclamation of the fine-size wastes (containing 20% - 60% clean coal by weight) provides, free of charge, mined and crushed feed stocks for coal recovery. Also, the removal or recovery of pyrite from the tailings should eliminate a major source of acid-water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the +100-mesh material produced commercial-grade coal averaging 7.6% ash, 0.8% sulfur and 13,471 Btu/lb. However, the coal yield, at about 31 % - 56%, was relatively low. Froth flotation, using mechanical and froth column methods, gave similar coal products at much higher coal recovery rates of 87% - 93%. This coal analyzed 10% ash and 1.1% sulfur.

Jan 1, 1993

Maximizing margins in competitive markets demands superior productivity. Unfortunately, management systems developed early this century for other industries often drive counterproductive behaviors choking mining productivity. Many executives and managers waste valuable time and effort relying on simply training and communicating to improve managerial practices and attitudes. In covering practical human behaviour, the paper explains why this fails -and explains how to use systems to successfully drive improved managerial practices and attitudes. It highlights use of modern performance Measurement, Analysis and Reporting systems to drive behaviors and improve margins -without capital investment -and make executive and managerial work easier and more effective.

Jan 1, 1999

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23 percent of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with L/D ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests a radial prestress of 3,000 psi or 5,000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3,000 psi prestress, was 54.3 percent for limestone, 40.3 percent for marble, 44.7 percent for sandstone, and 23.4 percent for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5,000 psi prestress, was 74.2 percent for limestone, 51.2 percent for marble, 61.6 percent for sandstone, and 29.7 percent for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room and pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent.

Jan 1, 1969

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016

By Chee S. Theng

As the 2015 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2015 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 338. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of AIME. Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2015 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-focus articles on gold processing, iron ore processing and coal processing. The 2015 Transactions consists of a total of 67 technical papers, encompassing all 22 papers published in 2015 in the Technical Papers Section of Mining Engineering (Vol. 67) and all 29 papers published in 2015 in Minerals & Metallurgical Processing (Vol. 32). Additionally, this volume contains 15 papers and one discussion that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2015 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2015

By Chee S. Theng

As the 2016 president of the Society for Mining, Metallurgy & Exploration Inc., I am pleased to present the 2016 issue of the Transactions of the Society for Mining, Metallurgy & Exploration Inc., Vol. 340. A significant portion of the contribution that we make as a professional society is the publication of professional and technical papers that accelerate the advancement of scientific knowledge and enable the transfer of technology. Communication within the mining community is the key to a successful society. This technology exchange continues a tradition that dates back to the 1871 meeting of 22 mining engineers in Wilkes-Barre, PA, that resulted in the founding of the American Institute of Mining, Metallurgical and Petroleum Engineers (AIME). Those individuals envisioned that these transaction volumes “would form a most valuable and greatly needed addition to our professional literature.” This volume fulfills that pledge. The 2016 Transactions contains some of the most interesting research and insights from the past year and features an international slate of authors spanning industry, academia and government. Papers include the latest findings from the U.S. National Institute for Occupational Safety and Health (NIOSH) and special-issue articles on process development testing. The 2016 Transactions consists of a total of 65 technical papers, encompassing all 21 papers published in 2016 in the Technical Papers Section of Mining Engineering (Vol. 68) and all 27 papers published in 2016 in Minerals & Metallurgical Processing (Vol. 33). Additionally, this volume contains 17 papers that are being published for the first time in this issue. The papers presented in this volume were written by some of the most distinguished professionals in the industry worldwide. All of the technical papers were peer-reviewed. The process of review and publication requires much hard work by authors, reviewers and our publications staff. As the 2016 president of SME and on behalf of all our members, I would like to extend our gratitude to all whose volunteer efforts contributed to the publication of this volume.

Jan 1, 2016

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016