Search Documents

By Louis P. Gignac

The Lac Shortt gold deposit is located in Northwestern Quebec, at some 115 km west of the Opemiska Division and 380 km northeast of the Lac Dufault Division, as shown on Figure 1. Falconbridge's exploration crews drilled the first six holes in the gold-bearing ore zone in 1979. After further diamond drilling from surface in 1980, the decision was taken to carry out an underground exploration program. A three-compartment shaft was sunk to a depth of 340 metres in 1981 and 1982; it was followed by an extensive exploration program, which included 1073 metres of cross-cutting and footwall drifting, 645 metres of ore drifting and 11 200 metres of diamond drilling. The underground work was completed by mid-winter 1983. It was followed by a complete feasibility study of the Lac Shortt Project. After some $Can 14.2 millions in exploration expenditures, the Board of Directors of Corp. Falconbridge Copper approved in July 1983 additional expenditures of $Can 45 millions to bring the Lac Shortt Mine in production at the capacity of 261 000 tonnes per year. Gold price was $US 425 per ounce at the time.

Jan 1, 1985

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dozer operators are frequently exposed to whole-body vibration (WBV) during the execution of their work. Occupational exposure to WBV in Indian surface coal mines was evaluated by measuring vibration intensity and duration of exposure. A triaxial accelerometer was placed on the operator seat surface for taking the readings. Based on frequency-weighted root mean square acceleration equivalent to 8-hr shift duration, i.e., (A(8)) all dozer operators have exceeded an Exposure Action Value (EAV) of 0.5 m/s2 , and 90% of dozers did not exceed Exposure Limit Value (ELV) of 1.15 m/s2 . Based on Vibration Dose Value (VDV (8)), all dozer operators have exceeded Exposure Limit Value (EAV) of 9.1 m/s1.75, but no dozer operators have exceeded Exposure Limit Value (ELV) of 21 m/s1.75. Further, an epidemiological study was performed for identifying the extent of musculoskeletal disorders (MSDs) among dozer operators. For the detailed study, 42 dozer operators and 22 controls were selected from 2 surface coal mines. The control group was not exposed to WBV. It was seen from the cross-sectional study that pain in the lower back was predominantly higher (83.33%) in the exposed group when compared with the control group (31.81%). Likewise, pain in the neck (47.61%), shoulder (42.85%), knees (42.85%), and ankle (11.90%) was higher in the exposed group than that of the control group (22.71%, 0%, 45.45%, and 4.54%). A significant observation among the exposed group was that there was degradation in the quality of life. The outcome of the study would assist in monitoring and mitigation of machinery-induced vibration diseases (MIVD) in India and generally applicable to most of the mechanized mines as well. However, comprehensive studies are still needed to enunciate the magnitude extent.

By R. J. Hickson

The giant El Abra copper mine project under development in Northern Chile will come on stream in early 1997 at a production rate of 500 million pounds of cathode copper annually. Ownership is 51 % Cyprus Amax and 49% Codelco. Cyprus Amax has construction responsibility. Total project cost is $1050 million. El Abra will incorporate latest operational technology with labor efficient practices to achieve world class productivity levels and low initial cash costs of about US $0.35/lb copper. Development procedures for the almost 800 million ton oxide deposit, as well as the hydrometallurgical processes selected for recovery of the copper values are discussed. Construction costs and pertinent technical data are shown.

Jan 1, 1996

By L. A. Roe

Calcium carbonate and talc fillers both find use in a multitude of Industries. Each filler has many commendable properties, and often compete for the same market. Quality controls for various grades are exacting and complicated. A detailed comparison of the physical and chemical properties of these two fillers is tabulated and the mining and processing of the ores is described.

Jan 1, 1980

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By Jean-Marie Deschamps

In an approach to the complicated study of bauxite from Les Baux de Provence it is necessary to consider the paleogeographical context of all the bauxites in southern France. These bauxites are of Karstic type, belonging to a metallogenic area extending from the Pyrenees Mountains to the Alpine Massif. Within this area each deposit does not always correspond to the same geological period. There are differing opinions regarding the origin of Karstic-type bauxite and a discussion of these various theories is beyond the scope of this paper. Bauxite of Les Baux, in Provence, was discovered in 1821 by the chemist, Berthier, near this picturesque village located in the region of Arles. It is Les Baux from which the name of bauxite originates. For a long time this bauxite was of no interest because of high silica 'and mediocre alumina content. Besides, the calcium carbonate content is somewhat high and is one of the main characteristics of Les Baux bauxite. The problem of exploration of the Les Baux deposit has been to prospect minable zones according to traditional norms where silica and carbonate are low.

Jan 1, 1977

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By Robert McIvor, Sami Makni, Andreia Rosa, Claude Gagnon

In response to the Natural Resources Canada “Crush It Challenge,” Corem partnered with the University of British Columbia and led a project to develop and demonstrate the use of high-pressure grinding to replace the workhorse of the industry, wet ball milling. Two plant case studies, a small tonnage gold recovery operation and a large tonnage copper recovery operation, were carried out. Plant circuit performances were compared to pilot plants operated on the same circuit feed setup to represent the novel equipment and flowsheet that was developed to produce separation circuit feed. Numerous obstacles to industrial implementation of high-pressure grinding in this role which were recognized at the outset of the work were successfully addressed. In both cases, comminution equipment energy savings alone and final stage total circuit energy savings exceeded 60% and 50%, respectively. Downstream mineral separation performance was the same or better.

Nov 28, 2023

By Arif Emre Dursun

The aim of this study is to present hazard classifications of location, type and causes of accidents in the Turkish coal-extracting industry using the analytic hierarchy process (AHP). In this study, fatal mine accidents were analyzed by pairwise comparison and weighting, and the most important hazards were identified by determining the effective main and sub-criteria among location, type and causes of accidents. For this purpose, first-, second- and third-level hazards consisting of location, type and causes of accident were determined by using the data of fatal mine accidents in underground and openpit coal mining in Turkey between 2010 and 2020.

May 1, 2024

By J. A. Reizes, C. A. J. Fletcher, T. Jancar

Spirals play an important role in fine coal and mineral processing. To date, almost all spiral designs have been empirically based. Although many operational units have evolved utilising this approach, it does not necessarily lead to optimal spiral designs. This paper presents the preliminary results of a collaborative computational and experimental research program to understand the detailed separation process which will ultimately lead to a parametric assessment of alternative spiral designs through computational simulation. Unlike the empirical approach, a computational simulation is only subject to the fundamental physics of the fluid flow. No prior knowledge of the generic spiral flow is necessary. The computer code implements a robust finite volume technique to predict the three dimensional fluid motion. A height function method is used to model free surfaces and the code is capable of handling arbitrary spiral geometries. Preliminary validation of the computational simulation is carried out through analysis of an existing spiral design -the Mineral Technologies LD9 unit. Computational flow predictions are compared with experimental measurements obtained using a number of techniques, including sampling and flow visualisation, for flow test cases where no solid particulate is present.

Jan 1, 1995

By L. A. Alcorn, H. E. Camargo, G. Gwaltney

"One of the most pervasive diseases in the mining industry is noise-induced hearing loss. The exposure of miners to noise levels above the permissible exposure level results in hearing loss in approximately 80% of coal miners by retirement age. In this context, the U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for longwall mining systems, which are used to extract half of the national underground coal production.From field measurements, previous research determined that the dominant sound-radiating components at the shearer of a longwall system are the two cutting drums used to remove coal. Due to the dimensions and complexity of longwall mining systems, the NIOSH project developed a validated finite element model of the cutting drum to use in predicting the sound radiated by the drum due to the excitation forces experienced in underground operations. This same model will be used to develop engineering noise controls for the drum. The excitation forces arise from the interaction of the cutting bits and the coal and are transmitted to the cutting drum through the bit holders. Due to the adverse conditions at the face, and a lack of instrumentation approved for underground use, the operational coal cutting forces have not been assessed before. To this end, NIOSH, in collaboration with Michigan Technological University, developed a self-contained, intrinsically safe instrumented bit to measure these forces.This paper describes the development of the instrumented bit and the measuring of operational coal cutting forces at three working coal mines. The measurements revealed that the forces have a flat spectrum, representative of the impact nature of these forces, up to around 100 Hz. Above this cutoff frequency, the force magnitude decreases at a rate proportional to the inverse of frequency squared."

Jan 1, 2014

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By Sadegh Elyasi

TBMand roadheader are two dominating excavation machines in underground tunnelling projects. The performance of these two tunnelling machines has been reviewed and analysed individually by many researchers from multiple points of view. However, there are almost no studies that have made an extensive comparison between these two machines, mostly from financial points of view. The current study is intended to characterize both financial and technical status of these two mechanical tunnelling machines in one of the biggest coal mines in Iran. The main objective of this study is to define the best method and equipment that meets a predefined economic goal, which is mainly to maximize the net present value. To this end, a technical and financial model based on the geomechanical and financial parameters involved in the project has been prepared and the financial part of the project has been carried out by applying COMFAR III financial analysis software. Subsequently, a sensitivity analysis of the model was conducted in order to evaluate the effect of involved parameters on the project. According to the results, a roadheader has better economic justification than a TBM, while the TBM has a better advance rate than the roadheader.

Feb 12, 2021

By Mustafa Kumral, Yuksel Asli Sari

Underground mining operations are sensitive to price fluctuations because they usually perform with a narrow profit margin compared to open-pit mining. Furthermore, the economic evaluations regarding operation are based on estimated or simulated grades rather than actual values. These bring a high degree of uncertainty to the viability of an operation. Hence, mine planning that accounts for uncertainty is crucial for underground mining operations. As an underground mining technique, sublevel stoping has geotechnical, curing time, seismicity, cost minimization, and production requirements. A new mixedinteger linear program is proposed that considers the uncertainty associated with net present value using chance-constrained programming. The net present value (NPV) maximization objective is transformed into a multi-objective maximization problem where one objective is to maximize the mean NPV, and the other objective is to maximize the negative standard deviation multiplied by a scalar called risk or reliability level. The balance between the two objectives was maintained by this scalar and was selected based on the reliability level of the project. A case study was conducted with varying reliability levels, and sequences were generated. It was shown that the expected net present value increased at higher reliability levels, and the overall value of the objective function decreased as the reliability level increased. In other words, the variance component penalized the value of the objective function. Moreover, it was observed from the case study that at lower reliability levels, stope grade order bears similarity to the extraction order.

Aug 4, 2023

By Glenn Melchert, Paul Eger, Jon Wagner, Dave Antonson, John Folman

Current approaches to reclaiming acid generating tailings include permanent water cover or encapsulation with various synthetic liners and/or clay. Although these methods can be effective, some ongoing maintenance will be required in perpetuity to ensure that water levels are adequately maintained or that the integrity of any capping system is protected. The successful creation of wetlands in tailings basins offers the possibility of creating a stable environment for the tailings with minimal maintenance. Acid-generating tailings from a massive zinc sulfide deposit in Winston Lake, Ontario, were placed in small cylindrical tanks to examine the feasibility and effectiveness of creating wetlands and mitigating acid and metal release. Two uncovered controls were established in addition to the five treatments, which were done in duplicate. Each wetland tank was 117 cm in diameter and contained 6 1 cm of tailings. Treatments included 61 cm cover of wetland soil, 61 cm of glacial till, 61 cm of tailings, and two tanks with 71 cm of water. One of the water covers included the aquatic macrophytes: Elodea canadensis, Potamegeton sp., and Ceratophyllum demersum. Cattails (Typha latifolia) were planted in the plots with substrate cover, and the initial water level was set at ten centimeters. The pH within the tailings in the treated tanks generally ranged between 6.0 and 6.5 and zinc concentration ranged from 0.02 to 0.1 mg/L. The drainage from the controls had an average pH of 3.3, and 7,700 mg/L of zinc.

Jan 1, 2000

By Shani Engelbrecht, Belinda McFadzean, Avuyile Wali, Natalie Shackleton, Vratislav Malysiak

Frothers play a crucial role in sulphide and PGM ore flotation recovery, and AECI Mining Chemicals studies on PGM ores have shown significant flotation kinetic increases with the optimal frother-collector combinations. Using Senfroth 200 as the industry baseline, remarkable kinetic increases were observed with AECI Mining Chemicals developed frothers in the first concentrate. Even in the worst-case scenarios, 4E PGM recovery increased by 5% at a slightly higher concentrate grade. It is important not to limit frother dosage to a fixed value. Instead, enough frother should be added to maintain a stable bench float, measuring the dosages by frother volume before and after tests. Frothers can be specialized blends and their importance should not be underestimated. The results produced by formulating and innovating frothers to address specific industry challenges have been encouraging. Testing a frother on a plant scale does not have to be as daunting as with collectors, enabling the identification of the best frother-collector combinations at an industrial scale. AECI Mining Chemicals bench scale testwork has motivated plant-scale trials that have successfully transitioned to commercialization. This paper compares the results from metallurgical and froth stability tests and shows that occasionally frothers that have a less stable froth can have improved valuable mineral recoveries, while still exhibiting better drainage for reduced entrainment and mass pull. It was shown that caution should be used when relying only on simplified froth stability tests in the evaluation of new frothers.

Feb 1, 2025

By C. A. Holley

The generation of coal fines is a growing problem which has serious environmental and resource recovery Impact. Several methods of agglomeration are studied including the production of briquettes for the consumer market. Simplified process flow diagrams, "order of magnitude" plant capital cost and operating costs are presented.

Jan 1, 1986

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

This paper combines theoretical and experimental analysis to conduct relevant research to improve the accuracy of predicting paste yield stress by slump flow. The analytical model of slump flow for yield stress is derived based on a mini-cylindrical mold with a height-to-diameter ratio of 1. It shows that the dimensionless slump flow is a monotonic decreasing function of the dimensionless yield stress and is independent of the material type (specific gravity), which provides a theoretical basis for quantifying the rheological properties of paste with slump flow. Three different tailing-prepared pastes were tested for their slump flow and implemented rheological tests simultaneously. The yield stress is obtained based on the Bingham model fit, as the measured value of the yield stress is substituted into the derived theoretical model. The studied pastes yield stresses range from 34.78 to 524.08 Pa, with corresponding dimensionless slump flow of 3.43 to 1.09. The results showed that the calculated slump flows were generally greater than the measured values. The analysis showed that this was mainly due to the thixotropy of the paste, with minor deviations ranging from − 1.5 to 5.8% for the less thixotropic pasted prepared from tailing C. An approximate analytical solution for yield stress as a function of slump flow is obtained using Taylor’s formula. However, it is unsuitable for predicting the yield stress because the yield stress calculated by this function is much higher than the measured value. The empirical yield stress model was constructed and experimentally verified. The results show that the empirical formula has high accuracy and good generality. The deviation of the studied pastes is between − 15 and 5%, which provides a practical method for rapid and accurate prediction of paste yield stress in mine sites.

Jun 1, 2023