Search Documents

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By Ernest M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger mines have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1983

By R. J. McLaughlin

Acid mine drainage (AMD) can occur as a natural phenomenon through oxidation of sulfide minerals. Oxidation by air and water can be exacerbated by mining. Because AMD can exhibit low pH, it is capable of extracting heavy metals from mineral deposits. The result is highly acidic drainage with elevated heavy metal concentrations -the combination of which can cause extensive environmental damage. Because of the importance of these factors, this paper is focused on sulfate based AMD. Due to widespread mining, the occurrence of AMD is ubiquitous. As a result, several approaches to treatment have been developed. Chemical treatment using alkali is most commonly employed to treat AMD. There are alternative methods of treatment, as well as alternative ways of handling treatment sludges or concentrates. Dewatering of sludge or concentrates is beyond the scope of this paper.

Jan 1, 1996

By J. Patrick Powers

In tunneling through water-bearing formations, the expense of controlling the water can have a major impact on overall project cost. The author has seen the cost of an eight-foot, finished sewer tunnel rise from under $500 per foot to over $1,000 when a water problem, anticipated as modest, became severe. There is need for greater professionalism in the approach to groundwater control. The days of the forked stick should be behind us. The basic technology exists. Its application is not yet widespread. This paper discusses predrainage; that is, the lowering of water in advance of tunnel excavation. Both free air and compressed air tunnels are considered. Examples from recent tunnel projects are described. SPECIAL NATURE OF TUNNEL DEWATERING Tunneling is unlike other excavations below the water table in a number of significant ways. The tunnel excavation is always on the critical path; if production slows or stops, there is no other work for the heading crews, no other work to carry the cost of service crews and job overhead. The dewatering commitment must be made well in advance. Construction of wells, and pumping down take time. After the heading reaches a trouble area, time is not available

Jan 1, 1997

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By M. Hepokoski, M. Klein

"Mine refuge shelters are designed to protect mine workers from hazardous environmental conditions after a mine disaster, but high temperature and humidity levels inside these shelters may pose a significant safety risk. Due to the safety risks associated with human testing, detailed thermal models of shelters and human occupants have been developed using TAITherm simulation software. These models are used to predict the temperature and humidity within the shelter resulting from metabolic heating, evaporation due to sweat and respiration, moisture and heat from the shelter’s carbon dioxide scrubbing system, and heat transfer within the shelter. A detailed human thermoregulation model simulates the sensible and latent heat generated by the shelter occupants, and predicts the occupant’s body core temperature and moisture lost due to sweating and respiration. This information is used to assess the safety of the shelter. This paper presents the technical details of the human thermal model, validation comparing the human model to human subject test data, and results of a mine shelter analysis. IntroductionPortable mine refuge chambers are used in U.S. coal mines to provide protection to mine workers from hazardous conditions following a traumatic event. Although these shelters are designed to supply clean air and sustenance for up to 96 hours, prolonged exposure to the mine shelter environment itself can pose a substantial risk to human safety. Heat generated by the shelter occupants combined with heat from the carbon dioxide (CO2) scrubbing system can raise the shelter interior temperatures and relative humidity to dangerous levels that can lead to heat stress in humans. Unfortunately, the thermal burden associated with mine shelter exposure is not well characterized due to potential hazards associated with underground human subject testing. In order to assess the thermal burden on people within a mine shelter environment, a detailed thermal model was created to accurately predict the temperatures and humidity levels within the shelter, and the impact of these environmental conditions on human occupants. The model consists of a mobile inflatable tent-type mine shelter with 23 humans, and includes the surrounding mine environment. The thermal simulations were performed using a validated commercial heat transfer prediction computer software. Additionally, a module of the software provided the capability to simultaneously model the thermophysiology of 23 unique humans contained within the mine shelter. The human thermal models accounted for the thermal interaction with the environment and provided a core temperature response prediction that can be used to evaluate survivability in heat stress situations (U.S. Army, 2003). The models can also be used to determine maximum occupancy in order to maintain safe temperature and humidity levels inside the shelter in specific mine environments, to optimize shelter size for maximum heat dissipation, or to simulate active cooling systems."

Jan 5, 2017

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By S. Daniel Thompson

In underground coal mining, the specification and control of belt and bunker capacities are complicated by (1) stochastic and intermittent conveyor loading, (2) a limited ability to reduce surge at the mine face, and (3) occasional overlapping of loading from two or more mine faces on the conveyors. Recently, because of longwall mining and other factors, the capacity requirements of most mine conveying systems have risen substantially; as a result, efficient capacity design and control have become important mine planning issues. This paper reviews these design issues and their associated modeling procedures. Design considerations and modeling difficulties are also examined.

Jan 1, 1996

By Keros Cartwright

Sanitary landfilling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for any natural limitations at a particular site Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) Regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites. (2) Site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources. (3) Re- search on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills. (4) Formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers.

Jan 1, 1970

By I. E. Odom

The rare magnesium-lithium clay mineral hectorite occurs at many places in the McDermitt caldera of Nevada-Oregon. Commercial development of several high purity deposits began in 1986. The hectorite was precipitated in a lake environment formed after collapse of the McDermitt caldera. Hectorite beds and lenses are associated with volcaniclastic sediments, limestones, dolomites, zeolites and locally sandy bentonites. The high purity deposits appear to be associated with hydrothermal areas. The hectorite consists of extremely small flake-shaped crystals, and Ca is the predominant exchangeable ion. Its color ranges from white to light green. Commercial uses developed to date include high brightness magnesium aluminum silicate products, organophilic clays, pulp retention, and ceramics. The MAS is used as a suspending agent, binder, stabilizer and thixotrope in aqueous solutions for cosmetics, household cleaners, pharmaceuticals and miscellaneous industrial applications. Organoclays are used in printing inks and paints.

Jan 1, 1992

By John M. Moore

Within the Pofadder district of Namaqualand, South Africa, economically exploited deposits of bedded barite and zinc-lead-silver-copper sulfides occur in close proximity within highly metamorphosed mid-Proterozoic pre-tectonic para¬gneisses of the Namaqualand Metamorphic Complex (NMC) (figure i). The paragneisses belong to the Bushmanland Group (SACS, 1980) that comprises a relatively straight-forward regional sequence of basal leucogneisses, intermediate mica-sillimanite schists and glassy quartzites, and a mixed upper zone of banded iron formations (BIF), minor marbles, quartz muscovite schists and localised uppermost quartz-pebble conglomerates and amygdaloidal mafic gneisses (Joubert, 1974) (figure ii). The base metal and barite mineralisation occurs in close association with BIFs, generally above the glassy quartzites, although in some cases possibly below them. In the regional context, the Bushmanland Group paragneisses are, to the north, intercalated with and ultimately replaced by meta-volcanic sequences of talc-alkaline affinity (Reid, 1977) belonging to the Orange River Group (SACS, 1980). The metavolcanics are generally of acidic to intermediate composition and show evidence of subaerial formation from 'high altitude shield volcanism' with many acidic ashflow and welded tuff bands, mesocratic and lesser melanocratic lavas and some fanglomerates (Ritter, 1980). To the south and east, the schist/quartzite associations are initially intercalated with and eventually replaced by cordierite gneiss/metacarbonate/biotite gneiss associations of shallow marine affinity (Moore, 1980a). The Bushmanland Group paragneisses appear to represent sedimentary material in the extreme distal portions of a talc-alkaline volcanic environment adjacent to a shallow platform sea.

Jan 1, 1983

By H. Russell, N. DePriest, J. D. Quaranta

Valley-fill structures built of blasted rock overburden from Appalachian mountaintop surface mines pose many reclamation challenges. The steep mountainous terrain, short valley lengths, and straight stream channel profiles create significant challenges to implementing fluvial geomorphic landform design in terms of both form and function, and from a safety and constructability perspective. The fluvial geomorphic landform design approach balances erosive and resistive forces by considering long-term climatic conditions, soil types, slope profiles and vegetation types. Commercial geomorphic landform design software tools do not specifically analyze the stability and factor of safety for the computer-designed landform slopes. This research investigated slope stability parameters and factors of safety between a traditional valley-fill design with a geomorphic landform alternative. Slope stability assessments were performed on two profile geometries. Finite-element modeling of a permitted valley-fill and a geomorphic design alternative indicated that slope angle and internal angles of friction associated with the gradation of the overburden greatly affected the designed factor of safety for both designs. The geomorphic designed slopes yielded the highest factors of safety out of 14 models analyzed with all cases having factors of safety over 2.0. The high factors of safety are attributed to shallow slopes and beneficial surface and internal drainage.

Jan 1, 2014

By William Gleason

There was a time, not too long ago, when the most daunting challenges facing those in the mining and mineral processing industries could be solved through better technologies and better practices. But now the challenges that come from the actual acts of mining and processing are just part of the bigger picture. SME?s Colorado Section of the Mineral Processing Division (MPD) hosted its 63rd annual meeting at the Broadmoor Hotel in Colorado Springs, April 25-27 and, while the conference had its fair share or mineralolgy and processing presentations that were heavy on the technical side of things, this year?s conference was also focused on the issues of permitting, regulation compliance and legislative issues. The so-called ?softer? issues, that, if not addressed, can lead to very real and very hard challenges. Under the theme ?Mine your own business - permits, startups, expansions and resources,? even the most dedicated metallurgists were drawn into the discussions of politics and legislation, and how those issues affect their business. Fittingly, Colorado Mining Association (CMA) president Stuart Sanderson was honored with the Arthur C. Daman Lifetime Achievement Award. Sanderson, an outspoken proponent for the mining industry in Colorado and beyond, also presented the keynote address to the lunch crowd where he spoke about framing public opinion toward mining and the efforts of the CMA to move the public opinion dial in a direction more favorable to mining. Sanderson explained that Colorado, once a Republican stronghold, turned after 2002 and now is controlled by Democrats who are traditionally less supportive of the mining industry. Sanderson said the deciding factor in the power shift was money, as supporters of Democrats outspent Republicans in the most recent election cycles. CMA has done its part to keep mining going in the state with a broad marketing campaign that was outlined by Sanderson.

Aug 1, 2013

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966

By I. R. M. Chaston

Abstract. This paper puts forward the concept of 'radial' plant layout where all crushing, milling and treatment operations are preferably concentrated in one central area and these separate stages are connected by radiating conveyors to and from outside storage areas. This system is contrasted to the more customary system of 'linear' plant layout where the crushing, milling and often the treatment operations follow one after the other in separate buildings. The radial system simplifies and improves contral and supervision to a very considerable extent and can lead to a form of continuous plant operation with the separate sectors shutting down in succession for necessary maintenance while maintaining the overall plant operation. The paper is illustrated with example: from past and recent diamond treatment plant practice in South Africa which demonstrate the reduction in plant labour achieved by this system. Previous objection to this type of layout on the grounds that it inhibited plant expansion are shown to be unwarranted. Radial Layout for Increased Treatment Plant Productivity A great deal of time and trouble is spent by highly qualified and experience( metallurgists in developing the right treatment process for a given ore. This process is then often expressed in a treatment flowsheet of the type shown in Fig. 1 which shows a typical diamond plant. This flowsheet, when completed, is commonly handed over to the mechanical engineers who then design the layout of the equipment indicated on the flowsheet and produce the working drawings upon which the detailed construction of the treatment plant will be based. It is an unfortunate fact that the tedious and time-consuming juggling of equipment and inter-plant transportation is often left to hard-working draughtsmen who, however capable' in their field, lack practical experience in the day-to-day operation and maintenance of the treatment plants they design. As a result many plants have been produced which, while they satisfy the requirements of the flowsheet with minimum capital requirements, cost far more than should be necessary to op¬erate and maintain. It is often possible to change individual items of equipment which do not achieve the performance required of them, but it is usually extremely expensive to change the basic layout of the plant if this should be found to be unsatisfactory. It should therefore be recognised that great care and attention should be spent on consideration of the basic layout of any treatment plant and that the views of both designers and operators should be fully regarded before settling upon the inevitable compromise dictated by the varying requirements of process-engineering and economics. It is unfortunate that this important subject receives such scant regard in the standard ore dressing text books and hand-books, being usually dismissed in a few paragraphs.

Jan 1, 1977

By Roberto Pimentel de Souza

Since 1976 CVRD is carrying out tests to develop a type of pellet made with organic binder. One binder that showed good possibility to be used in industrial plants is Peridur. An extensive framework of tests was run in CVRD's pilot plant. The results are presented in this paper. Finally, the decision was taken to carry out an industrial production of 50.000 t of pellets. It was scheduled for March '81. The results are shown in this pager. It was not observed any detrimental effect of the peridur neither in the process nor in the product quality.

Jan 1, 1981

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979

By Drupad B. Desai, Alexander Rosenbaum

In recent years, there has been an increasing use of two-pass tunnel lining system consisting of segmental unbolted expandable precast concrete initial lining and cast-in¬place concrete final lining in the United States. Used so far in soft ground tunneling performed under free air, it often includes a waterproofing or gasproofing membrane placed between the initial and final linings. This paper describes the utilization of this two-pass system for an extension of the Baltimore Metro, constructed in part under compressed air. It offers a description of the extension project, known as Section C; addresses the tunnel lining selection process and the design of the lining elements; examines the effect of the adopted lining system and tunneling technique on the design of the project's major structural components; and describes design modification instructions in order to accommodate constantly changing field conditions.

Jan 1, 1993

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By Charles A. Rhoades

The Bureau of Mines is conducting research on a dual leaching method that offers the potential for the economic recovery of the silver as well as the manganese contained in some of the domestic manganiferous silver deposits. The method is an initial leach of the manganese with aqueous SO2 followed by a neutralization rinse, and then by a second leach for the extraction of silver with cyanide solution. Refractory silver in these ores is either bound by the high-valence manganese, chemically resistent to cyanide leaching, or is rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization. Less than 10 pct of the silver was extracted when -1 in +1/2 in (-2.5 cm + 1.3 cm) ore pieces were leached directly with cyanide. However, extractions of 25 to 82 pct for silver and 65 to 96 pct for manganese were attained in laboratory column leach tests using the dual method on the same size ore pieces from six domestic deposits.

Jan 1, 1984