Search Documents

By Reginald E. Reid

Mining on Bureau of Land Management (BLM) administered lands is affected by Federal laws and regulations requiring the mining industry to plan for the environmental consequences of surface disturbance. Regardless of the requirements for obtaining a claim, permit, lease or contract to mine, a notice or a mining and reclamation plan will be submitted and an acceptable environmental document must be prepared prior to mining. A bond may be required based on the results of the environmental evaluation, public interest and the operator's past history of compliance. In several areas, Federal requirements are different from California's requirements under their Surface Mine and Reclamation Act (SMARA). Therefore, the BLM is negotiating with the State in order to work out problem areas of responsibility and duplication of effort.

Jan 1, 1984

By P. B. Altringer

The Bureau of Mines conducted laboratory tests to develop a process for recovering a marketable grade of tungsten from the brine of Searles Lake, Calif. The brine contains only 56 parts per million of tungsten (70 ppm WO3). Using ion exchange resins synthesized by Bureau chemists, 98 percent of the tungsten was extracted from the brine and 92 percent of the tungsten vas recovered as a marketable iron-tungsten concentrate containing 44 percent tungsten as tungsten trioxide. Although major technical problems have largely been resolved, research is progressing to escalate testing in a process investigation unit to provide more reliable data for an economic appraisal.

Jan 1, 1978

By Brenton Cook, Nate Long, Larry Applegate, Aaron K. McCain

"The Northgate Link Extension project is the third phase of the Sound Transit master plan to extend light rail throughout the greater Seattle metropolitan area. When completed, the Northgate Link Extension will extend the existing light rail system north by about 7 km (4.3 miles) from the University of Washington to the Northgate neighborhood. A general overview of the project alignment is provided as Fig. 1. The project was funded by a combination of federal grants and allocations from local taxes. The general contractor on the project was JCM Northlink LLC (JCM), a joint venture between Jay Dee Contractors, Frank Coluccio Construction Company and Michels Corp. SoilFreeze, Inc. was retained as a subcontractor to provide ground freezing design and construction services.The project involved the construction of two parallel 5.5-m, 25-cm (18-ft, 10-in.) (inside) diameter tunnels using earth pressure balance (EPB) tunnel boring machines (TBM) and precast segmental concrete tunnel liners. The two tunnels maintained roughly the same elevation along the alignment and were spaced roughly 12 m (40 ft) apart (centerline to centerline). A total of 23 cross-passages connecting the two tunnels were included at approximate 244-m (800-ft) intervals. Cross passage excavations were elliptical in shape with dimensions of approximately 5.6 m (18.5 ft) in height and 5.3 m (17 ft) in width. The cross-passages were 5.8 to 6.1 m (19 to 20 ft) long as measured between the exterior of the tunnels at springline elevation. Cross passages were intentionally located directly beneath public right-of-ways thus avoiding buildings. Many of the cross passages were located beneath narrow roads in residential neighborhoods with mature vegetation, existing utility structures and piping and limited parking areas. Excavation and support for each cross passage was completed using the sequential excavation method (SEM).The subsurface soil and ground water conditions at the cross-passage locations were described in the Northgate Link Geotechnical Baseline Report (GBR) prepared by Jacobs Associates and the Northgate Link Geotechnical Data Report (GDR) prepared by Shannon and Wilson, Inc. Soils along the project alignment were glacially overridden and characterized as very dense or hard. Subsurface soils consisted of cohesionless sand and gravel (CSG), cohesionless silt and fine sand (CSF), cohesive clay and silt (CCS) and till and till-like deposits (TLD)."

Dec 1, 2018

By Zong‑yu Li, Shao‑jian Ma, Xiao‑jing Yang, Jin‑lin Yang, Xing‑nan Huo, Heng‑jun Li

Optimizing and adjusting the particle size composition of grinding products is of great significance for improving economic benefits and resource recovery and utilization. In this study, grinding contribution and quantitative separation of impact and grinding mechanism in cylindrical mill were creatively researched, and the grinding technical efficiency of impact and grinding was coupled to the grinding technical efficiency of grinding in drop-off mode. The results showed that the contribution rate of impact and grinding in grinding in drop-off mode varied with the grinding time. On the whole, the contribution rate of impact action increases with the grinding time and gradually becomes stable, and the contribution rate of grinding effect was just the opposite. Under the experimental conditions, the main contribution of the grinding process is impact action, and the contribution of grinding action is auxiliary. In addition, the contribution rate of impact and grinding effect in grinding in drop-off mode was also related to the feed particle size. The contribution rate of impact effect decreased with the decrease of feed particle size, while the contribution rate of grinding increased inversely.

Aug 3, 2023

By W. K. Connor, O&apos

The Bureau of Mines is investigating the Co and Mn resource of the West-Central Arkansas District, including field investigations, mineralogical characterization, beneficiation, and hydrometallurgical tests. The deposits occur within the Ouachita Mountains and are con-trolled structurally, occurring along the axes of anticlines making up the mountain ridges. Brecciated novaculite is cemented with a mixture of Mn oxides, primarily cryptomelane and psilome-lane. Cobalt is concentrated within a particular Mn oxide phase, lithiophorite. Chemical analyses on head samples reported up to 25 pct Mn and 0.17 pct Co. Magnetic separation yielded products with up to 41 pct Mn and 0.22 pct Co at recoveries of 95 pct Mn and 93 pct Co.

Jan 1, 1991

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By Cyrus W. Field

The Pacific Northwest as defined in this review comprises an exceedingly large and geologically complex terrain that occupies the 'Western Cordillera mobile tectonic belt. This metallogenic province is approximately 2100 miles long and 350 to 500 miles wide. It extends north-northwest from northern California and Nevada, through western Idaho and Montana, Oregon, Washington, British Columbia, and southwestern Yukon Territory, to southern Alaska, and west from the western flank of the Northern Rocky Mountains to the continental margin (Fig. 1). Many detailed and thorough exploration programs that have been conducted by mining and petroleum companies for over a decade have demonstrated that porphyry-type deposits are both numerous and wide-spread throughout this province. Although the Granby Mining Company extracted about 34 million tons of copper sulfide ore from Copper Mountain during the period 1900-1957, intentional large-scale production of porphyry-type ores was first initiated in 1962. It began at Bethlehem Copper Corporation's East Jersey orebody in the Highland Valley District of south-central British Columbia, approximately eight years after Mr. H. H. Huestis rediscovered that broad zone of copper-molybdenum metallization and recognized its potential significance.

Jan 1, 1973

By Mark A. White

Arch Mineral has developed several computer programs that aid the surface mine planning function. These programs are utilized to perform long term projections for various area or semi-area stripping operations. The program generated reports include yardage, tonnage, quality and ratio information for the user-specified time periods. The projections are used to anticipate the annual budget, to compare alternative mine plans and to analyze acquisition candidates. The programs are user friendly, fast and accurate. Geological Grid File Two data files must be set-up and used in conjunction with the mine planning programs. These are a geological data file and a general input file.

Jan 1, 1984

By B. W. Cavender

The operating lifetime, or production rate, selected for a mining project is among the most important factors influencing the design and ultimate economic success of the project. An incorrectly-determined lifetime can lead to the erroneous rejection of projects as uneconomic as well as the suboptimal exploitation of producing properties. This paper examines the calculation of the optimal lifetime using both traditional discounted cash flow and recently-proposed option pricing techniques. Using each method, the production rate is determined as that rate at which the net present value of the project is maximized.

Jan 1, 1992

By Alvaro Lucio

The continuous increase of the fuel oil price compelled CV3D to look for an alternative fuel. Charcoal was selected as the alternative energy source. This paper justifies its selection, describes charcoal properties, the methods for using charcoal in the pelletizing and shows the results of the in-plant tests.

Jan 1, 1982

By Duah Philip, Awuah-Offei Kwame

Regulatory pressure to mitigate the cement industry’s environmental impact has intensified recently, spurring innovation in low-carbon cement technologies. In the United States, cement production, consumption, and carbon emissions are accelerating. Despite this trend, the adoption of environmentally friendly dry clinker production technology with combined preheater-precalciner systems has surged from 53.3% in 2002 to 88.5% in 2019. Concurrently, reliance on wet technologies, known for their higher environmental impact, has dropped from 16.5% to 0.6% within the same period. This paper presents the results of our comprehensive study, utilizing over 100 years of industry data, to analyze these technological shifts and their environmental implications.

Feb 1, 2025

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

Smart defense: that?s what the industry needs to play for the next four years, according to panelists at the 118th Annual Meeting of the Northwest Mining Association (NWMA), which met December 2-7 in Spokane, WA. The conference was well attended, with approximately 2,200 attendees, 244 booths in the two packed exhibition halls, and a rich offering of short courses, field trips, social events and technical sessions. Speakers at the packed legislative session articulated many of the frustrations felt by members of the mining community after the U.S. elections in November, and offered words of advice. Matthew Ellsworth, the new Government Affairs hire at NWMA, stated it best: ?Elections are like Christmas: you find out who?s naughty and nice ? and it?s always going to come again.?

Jan 1, 2013

By George J. Skoronski

The economics of pellet plant operation, in terms of fuel and power consumption, flexibility in the selection of the cheapest fuel source, system availability, maintenance costs, and the simplicity of process design, contribute to the determination of building and profitably operating a pellet plant. Design innovations, sup- ported by actual field data, have been initiated into the GRATE-KILN System design to positively address these factors. This paper presents the recent state of the art design concepts which have helped the GRATE- KILN System assume worldwide acceptance status.

Jan 1, 1983

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2018

By D. R. Willmer

An understanding of how health and safety management systems (HSMS) reduce worksite injuries, illnesses and fatalities may be gained in studying the behaviors of health and safety leaders. These leaders bear the accountability for identifying, understanding and managing the risks of a mining operation. More importantly, they have to transfer this knowledge of perception, recognition and response to risks in the mining environment to their workers. The leaders’ efforts to build and maintain a mining operation’s workforce that consistently executes safe work practices may be captured through more than just lagging indicators of health and safety performance. This exploratory study interviewed six leaders in occupations such as site-level safety supervisors, mine superintendents and/or general managers at surface and underground stone, sand and gravel and metal/nonmetal mine sites throughout the United States, with employee populations ranging from 40 to 175. In exploring leaders’ perspectives on how they systematically manage health and safety, examples such as approaches to task training, handling near-miss incidents, identifying future leaders and providing workers with feedback offer insights into how leaders translate their knowledge and management of site-level risks to others.

Jan 1, 2017

By Verya Nasri, Behrouz Esmaeilkhanian, Mohammad Motallebi

Réseau Express Métropolitain (REM) is the new Light Rail Transit (LRT) network of Montreal, Canada. This new LRT network uses a century-old Mont Royal Tunnel (MRT) to connect Downtown Montreal to the north side of the Island of Montreal by passing through Mount Royal Mountain. This railway double track horseshoe tunnel is approximately 5 km (3.1 mi.) long, 8.8 m (29 ft.) wide and 5.5 m (18 ft.) high, with a constant 0.6% grade. Due to different geological characteristics of the surrounding ground, varied from hard rock to soft soil, different cross sections and excavation methods were adopted for construction of this tunnel. In order to use MRT in the modern transit system, the tunnel needed to be inspected, rehabilitated and be compliant to the recent safety standards. This paper presents a summary of history and characteristics of the existing tunnel plus the implemented steps to upgrade the tunnel. It includes the details of the structural inspection and rehabilitation methods of the tunnel. Further, this paper summarizes the procedures for the space proong, construction of the separation center wall, and the tunnel enlargement. It also describes parts of complications encountered during the construction and solutions implemented to tackle these issues.

Jun 23, 2024

By G. Wheeler

Epithermal gold exploration in the last decade has developed useful models for exploring new ore districts in Oregon. In Eastern Oregon, disseminated gold occurs in epithermal deposits that have been pervasively silicified and brecciated. Many gold prospects staked since 1980 are in fluvial and lacustrine sandstone and conglomerate deposits. Clay alteration products and disseminated pyrite may be present. Vein filling calcite and thin to thick quartz veins are common. Late stage quartz forms pseudomorphs after calcite in many deposits. Arsenic, mercury and gold are geochemically anomolous but silver is usually not. The epithermal deposits are located in part of the Deer Butte Formation or equivalent units. Exploration criteria include the presence of Deer Butte Formation or correlative units and NW structures cut by N-S basin and range structures.

Jan 1, 1987

By David Harrison

Exxon Minerals Company uses geostatistical techniques for ore resource evaluation of its mineral projects. These techniques provide the most reliable estimates of recoverable tonnage and grade and uniform and realistic confidence limits. A schema has been developed which categorizes the company's successive evaluation phases. Clear separation is intended between geostatistical estimates and other factors in project evaluation such as mining, metallurgy, and economics. Company management seeks consistent and reliable estimates for investment decision-making and to meet growing demands for disclosure of mineral assets.

Jan 1, 1983

By Giorgio De Tomi, Rondinelli Sousa

Whilst all public mineral reporting codes require classification of mineral resource and reserves according to the level of geological knowledge and confidence of the estimates, companies are not required to disclose how mineral estimates and associated cashflow projections respond probabilistically to the incorporation of different types of risk events. As the level of expectations and scrutiny of investors and stakeholders continue to increase over the years, it will be essential for companies to adopt an integrated framework for sensitivity analysis to increase corporate value through better capital allocation and reduce potential losses associated with poor investment decisions. Failure in fully capturing the impact of unexpected incidents in mineral estimates and financial modeling could be extremely harmful to the business, affecting the company’s reputation, and negatively impacting the relationship with stakeholders.

Feb 22, 2026