Search Documents

By Ma Fangyuan, Li Min, Xu Bing, Xian Yushuai, Zhao Tonglin

The study explored a new combination amine collector (XK-28) that can obtain better flotation index and defoaming rate for magnetic iron ore. A pure quartz mineral test indicates that dodecylamine, XK-I, or XK-II has good collection effect on quartz and their best flotation pH is in the range of 6–7. The experimental results of a combination collector (XK-I:XK-II = 2:8.) show that the separation effect for quartz and magnetite is better than that of a single collector. The single factor for actual mineral test shows that when the combined reagent is used as the collector, the best conditions are pH = 7, 90 g/t dosage, and XK-I:XK-II = 2:8, which is consistant with the pure mineral test. The difference for dodecylamine as a collector is that the optimal dodecylamine dosage is 60 g/t. Under the best conditions of actual ore test, dodecylamine and XK-28 are respectively used as the collector to compare the flotation indexes. Study results indicate the magnetite grade using XK-28 as the collector is higher by 3.02% than that of using dodecylamine, recovery is increased by 1.92% over that of using dodecylamine. Based on the measurement results of zeta potential, uses of XK-28 can slightly increase the zeta potential difference of quartz and magnetite to enhance the flotation effect. The mechanism of action between the XK-28 collector and the actual ore from the Gongchangling plant is physical adsorption, and this adsorption also has hydrogen bond formation. Contact angle results shows that XK-28 improves the hydrophobicity of quartz better than dodecylamine. Compared with dodecylamine, XK-28 is more sparsely arranged on the surface of the foam. The foam produced by the XK-28 collector has better air permeability and it is more likely to merge and disappear with bubbles.

Jul 21, 2021

By J. Fisher, M. Barish

Over the past several years, Somerset International has successfully installed over 20 patented Sub325® Fine Coal Recovery Systems in the United States, Australia, Canada and Russia. These installations recover between 5 TPH and 40 TPH for the host sites. In addition to the increased revenue from the direct recovery of a recirculating load (Screen Bowl “Insurance”, Direct Recovery vs. Indirect Recovery via Recycle, CPSA 2020), host sites have seen benefits ranging from improved operation of refuse equipment to a reduction in the solids content of the refuse streams. As Somerset has improved ultra-fine coal recovery through the introduction of Sub325® Effluent Flotation and, most recently, the Sub325® Effluent Settler™, the amount of coal that has been recovered from these systems has increased by up to as much as 25%. Many host sites have taken a sense of ownership in the Somerset system and consider it to be a critical circuit in the overall optimal performance of the plant. In the past year, Somerset has taken the initiative to expand upon the capabilities of the Sub325® Fine Coal Recovery System, primarily the Sub325® Solid Bowl Centrifuge, to include Refuse Tailings Dewatering to allow for co-mingled refuse disposal. As slurry ponds and boreholes are becoming difficult to impossible to permit and operate, there is a need for a reliable, low-maintenance, continuous operation that can produce a handleable refuse cake. Refuse tailings disposal applications are by no means limited to coal plants and impoundments. Somerset has successfully tested at iron ore and phosphate locations throughout the world and have begun commercial installations. The ability to dewater -325 mesh material, whether it be coal, coal refuse, iron ore tailings, or something else, is a vital piece of processing capability for the continued production of mining operations across the globe. This paper highlights the success that Somerset has had in the coal industry worldwide as well as the initial successes with phosphate, iron ore, and copper tailings (patent pending).

Mar 2, 2022

By Brendan Demich, Linda L. Chasko, Brendan Macdonald, Timothy J. Orr, Jessie J. Mechling, Cassandra Hoebbel, Jason Navoyski, William Helfrich, Jessica Cohen, Paul E. Schmidt, Jennica L. Bellanca

The National Institute for Occupational Safety and Health (NIOSH) in partnership with the Mine Safety and Health Administration (MSHA) developed VR Mine Rescue Training (VR-MRT). It is a training platform that allows mine rescue team members to explore virtual emergency scenarios collaboratively. Team members use a head-mounted display to visualize and interact together with equipment, hazards, and dynamic ventilation. All player actions are recorded and displayed for debriefing. Researchers at NIOSH demonstrated the training platform at various mine rescue competitions, including the International Mine Rescue Competition, and collected feedback. Participants’ responses were overwhelmingly positive. This paper describes the development of the software platform and the results of the usability surveys and interviews.

Jun 25, 2023

By J. Marsden

Lift height, overall heap height and climate all play an important role in determining precious metals leaching rates, recoveries, operating costs and capital cost requirements for heap leaching operations. The effects of these factors are not easy to predict from testwork, and this can result in unexpected delays in metal production, lower recoveries than expected and higher capital and operating costs than necessary. This paper investigates the economic impact of lift height, overall heap height and climate on heap leaching and provides criteria to assist in the design and operation of leaching facilities. Descriptions of three heap leach operations in the western USA are provided to support the discussions and conclusions.

Jan 1, 1995

By David Mast, Amanda Foote, Mina Shinouda

The Michigan DOT’s I‑75 Modernization Project, Segment 3, is a 30-year, $1.2 Billion design-build-finance-maintain project in Southeast Michigan. The scope includes building a nearly 4-mile long, 14.5-foot ID stormwater storage tunnel. The tunnel and pump station are being built concurrent with new roads and bridges, requiring multiple levels of design and construction coordination. Underground risks include the poten‑ tial for encountering granular soils, groundwater, and explosive gases. The new tunnel will be mined by a new open-face TBM and lined with a one-pass steel-fiber-reinforced precast concrete segmental lining. Shaft construction began in early 2020 and tunnel mining in July 2020.

Jun 13, 2021

By A. D. MacPhail

The Highland Valley Copper partnership was formed in July 1986 and was the logical result of a mine with a large ore reserve but no adequate mill, and a mine with a large, modem mill but dwindling ore reserves. The original partners -Cominco and Lornex -were joined in January 1988 by Highmont Mining Co. which contributed a two-line concentrator. During 1988/1989, the Highmont mill was moved 7.5 km to adjoin the Lornex mill, forming what is now called the Highland mill, with a current nominal capacity of 130 000 tonnes per day. The mine is located 220 km northeast of Vancouver, British Columbia and is close to four communities in which personnel make their home: Logan Lake, Merritt, Ashcroft, and Kamloops. The map in Figure 1 2.2 shows the general area. Kamloops is a major service centre and is serviced by two railways, two major roads and a regional airport.

Jan 1, 1993

By R. P. Fischer

Traditionally, molybdenum and vanadium have been used chiefly as alloy metals in steel. They impart similar characteristics to most steels, and to some extent one can be substituted for the other. In the United States during the 1950's the production of steel increased about 5 percent, and the reported consumption of both of these alloy metals in steel increased some 40 percent. In Europe during the 1950's the production of steel in¬creased nearly 100 percent. Data on the actual consumption of these alloy metals in European steels are not available, but production and trade records show that the European supplies of molybdenum increased about 150 percent and those of vanadium about 350 percent during the 1950's. If most of the molybdenum supplies in Europe are being added to steel, as seems likely, then the European steel industry has nearly caught up with the United State in the rate of consumption of molybdenum in steel. The vanadium supplies, on the other hand, are puzzling--unless Europe is adding mach more vanadium to steel than is done in the United States, it seems reasonable to assume that other uses are consuming moderately large quantities of this metal or that appreciable amounts of it are being transshipped from Europe. To the extent that a changing volume of supply signifies a changing pattern of use, the increased demand for molybdenum and vanadium in Europe should be of interest to domestic producers and consumers of these metals.

Jan 1, 1964

By MAHESH SHRIWAS, CHRISTOPHER PRITCHARD

Ventilation monitoring and control in mines are becoming an integral part of day-to-day activity for maintaining health and safety of miners. The authors evaluate potential real-time monitoring solutions for detecting and reducing diesel particulatematter, mine fires, and dust in situ, and examined the state-of-the-art use of ventilation monitoring and control in underground mines for detecting and reducing air contaminants to acceptable regulatory limit. Authors review relevant documents, including research papers, trade publications, and manufacturers’ website-based information, to identify research gaps. The authors also evaluate contemporary sensors (airflow, gas, dust, silica), control system and software technologies, data transport systems, Industrial Internet of Things, ventilation network simulators, and control devices to identify potential health and safety research gaps. In this study, examples of some mines from Canada, Australia, and the USA are included where ventilation monitoring and controls have been applied. Overall, this review identifies multiple challenges and research gaps in applying mine monitoring and control systems that could be the focus of future research, offering potential improvements to miner safety and health and financial benefits.

May 12, 2020

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

By A. Fuerst

This paper delivers insights into how high availability combines with high efficiency at the Yanacocha Plant, Newmont Mining Corporation, Peru. Advances in motor design and maintenance with integration of smart control support the approach plant maintenance staff is applying to deliver such excellent results for availability and efficiency in Yanacocha and elsewhere. Detailed efficiency and availability data for 2011 and 2012 in Yanacocha are provided. ABB and Yanacocha teams collaborate closely by combining their experience and continuous development of gearless mill drive procedures and maintenance knowledge to deliver the impressive performance being achieved. The secrets for high performance shared by the Yanacocha maintenance operations point to their systematic, practical adherence to modern asset management and maintenance concepts.

Feb 27, 2013

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By J. L. Whitlock

A mutant strain of Pseudomonas paucimobilis is utilized to effectively degrade and or remove 90-98% of cyanide, thiocyanate, toxic heavy metals and ammonia from a cyanidation mill process and mine discharge maximum of 21,000 m3/d (5.5 MGD). Homestake Mining Company?s biological wastewater treatment plant has been in full scale operation for over 2 years at the Homestake Mine in Lead, South Dakota.

Jan 1, 1987

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By Del Brock, Dan Wooton

The design/build of two adjacent vertical mine shafts in difficult ground conditions at a mining complex in the midwestern United States required innovative construction techniques. Construction of the 267-m-deep Service Shaft required full depth dewatering wells and ground freezing. Blind drilling was utilized to excavate the 257-m-deep Production Shaft and it was finished with a steel/concrete composite liner that was floated into place. An equally unique component of the installation included supplying a high capacity vertical conveyor system, featuring a 273-m-lift. Other components of the project include the mine level development, as well as the design and installation of three hoisting systems, including a 45-ton capacity men/materials hoisting system.

Jan 1, 2003

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By P. R. Taylor

This investigation (Bowles, 1990) involves consideration of technology utilized by three separate fields of metallurgy and materials science: 1) The recovery of metals employing the use of solvent extraction, 2) The fabrication of materials using powder metallurgy, and 3) The use of composite materials in fabrication of engineering materials. The research considers each of the processes in order to realize the benefits of each. In light of the fact that materials have an intended use -it does seem plausible to simplify the process required between "mother earth" and final use. For instance, a primary copper producer that already employs a solvent extraction and electrowinning process could produce value added products directly. Part of the existing extractant flow could be diverted into a pressurized hydrogen stripping process in order to produce specialty composite powders. Innumerable methods have been employed for the recovery of metals; solvent extraction, the one considered in this study, was used due to the possibility of it providing a pure powdered metal. The use of solvent extraction in the recovery of metals has gained wide acceptance and its use proves beneficial in many applications (Ritchey and Ashbrook, 1984). Pressure hydrogen stripping of solvent extractants may provide the benefit of flowsheet simplification compared to conventional solvent extraction followed by electrowinning. It may also provide the benefit of direct production of high purity metal powder (Demopoulos and Distin, 1985).

Jan 1, 1992

By P. E. Lenz

In Nevada, large deposits of diatomite were formed during the Miocene / Pliocene in deep, alkaline lakes. Associated sediments are predominately fine-grained lacustrine with varying fluvial-clastic layers. Tephra layers are common, and probably served as a source of soluble silica for the extensive diatom colonies. Four companies are currently producing diatomite from Nevada deposits. Nevada ranks second to California in annual domestic production. Nevada diatomite is used in filter aids, fillers, absorbents, catalyst supports, and many other products. Economics and mineral reserves indicate that diatomite production in Nevada will be significant well into the next century.

Jan 1, 1993

By Robin J. Hickson

The Grasberg copper-gold deposit was discovered in the spring of 1988, one year before the planned closure of Freeport Indonesia's original Ertsberg openpit copper mine. In spite of Grasberg's remote location, 600 m (1968 ft) above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought its latest open-pit mine into production in the last week of 1989, less than two years after discovery. Freeport Indonesia's (FI) copper-gold mining operations are located in Irian Jaya, the easternmost province of Indonesia on the western side of the island of New Guinea. Fl's six ore deposits are all located within a 10- x 10-km' (3.9- x 3.9-sq mile) Contract of Work area. They are all between the elevations of 2900 and 4300 m (9515 and 14,100 ft) above sea level, some 96 km (60 miles) from the island's southern coast. A 118-km (74-mile) access route connects FT's port site of Amamapare on the Arafura Sea to the project area. The first section is an 18-km (11-mile) barge waterway. The final 100-km (63mile) is a two-lane gravel highway. The highway terminates 9 km (5.5 miles) beyond the FI townsite at the project's central mill, some 2850 m (9250 ft) above sea level. The mining areas are separated from the mill by a 780-m (2560-ft) sheer cliff face. The world's longest free span tramway system, with a total length of more than 1.6 km (1 mile), is the only means of access for men and materials between the mill and the surface mines. Weight restrictions for the tramway for equipment considered for the project are 15.4 t (17 st). The minimum clear width dimension of two tunnels along the portsite access road is 5.6 m (18.4 ft).

Jan 1, 1991

By P. A. Cornejo

Blastings always generates induced vibrations through seismic wave, these are lost energy from the blasting and therefore causing the disturbance of slopes and structures near the blast source. Most of the components of an open pit mine have to reach a physical stability, especially during its closure process. Aiming to develop a vibration prediction model using the historical records from an open pit mine located on Peru, this research has two main focuses depending on the distance from the blast source to the structure: to protect the final slopes and to protect the villagers houses. Both are based on the Devine model of the Square Root Scaled Distance (SRSD) to predict the Peak Particle Velocity (PPV). The Mid field model, where is found mainly final slopes from the pit, limited by the failure criteria of McKenzie based on the geo mechanical properties of the rock mass. The Far field model ranges distances where are located the most community households, limited by the German rule DIN 4150 for highly sensitive structures. Both scenarios resulted on a distribution abacus to limit the weight of used explosives to get the best operational advantage and structure safety.

Mar 2, 2022

By D. S. Yantek, R. J. Matetic, A. K. Smith, E. D. Thimons, J. Srednicki

In a 2007 report to the U.S. Congress, the Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) stated that built-in-place refuge alternatives (BIP RAs) provide significant advantages over mobile refuge alternatives. At present, the requirement to locate refuge alternatives within 305 m (1,000 ft) of working faces makes BIP RAs impractical in most coal mines. BIP RAs would be practical if three issues are addressed: (1) allowing BIP RAs to be located at greater distances from the working face, (2) developing a reliable process for the design and approval of BIP RA stoppings that meet the 0.1-MPa (15-psi) design criteria, and (3) developing systems that reliably deliver breathable air to the refuge alternative. In 2015, NIOSH OMSHR conducted a study of these three issues and issued a report. In the report, justification was provided for allowing the placement of BIP RAs at greater distances from the working face than the currently mandated 305 m (1,000 ft), guidelines were developed that could be used by industry when submitting BIP RA stopping design applications for approval which are patterned after the Mine Safety and Health Administration guidelines for coal mine seal design applications, and insights were provided into options for providing a reliable supply of clean, breathable air to BIP RAs. This paper presents a summary of the study’s findings and also addresses issues discovered during the building and designing of a BIP RA that OMSHR researchers constructed in NIOSH’s Experimental Coal Mine in Pittsburgh to research the testing and improving of BIP RAs. These issues include several issues related to the delivery, distribution and exhaust of ventilation air to the BIP RA and some general construction issues that require further investigation.

Jan 1, 2016