Search Documents

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By N. L. Hayward, V. H. Ness

In the past decade Australia has seen the development, construction and commissioning of three complex processing plants for the treatment of lateritic nickel ores. These have all been based on high pressure acid leaching (HPAL) for extraction of nickel and cobalt into solution, followed by solid liquid separation in a CCD circuit. However, flowsheets for separation and purification of the nickel and cobalt diverge markedly. The existing plants have been commissioned with varying degrees of success, with a variety of problems ranging from materials of construction to inadequate design. While the process problems are not insurmountable, there is much room for improvement. Currently there are several new HPAL plants at the feasibility or financing stage. All of these have adopted one of the existing flowsheets. Most of the enhancements have focused on increasing autoclave size. It is now time to assess the success and failures of the three existing plants and incorporate this experience in a design for productivity, efficiency and reliability. Towards this end, this paper discusses aspects of flowsheet optimization, materials of construction and engineering design.

Jan 1, 2001

By F. F. von Glehn

There is no doubt that simulated ventilation networks must be adequately verified before they can be extrapolated and used for predictive purposes. There are two general approaches as to how the verification can be established and these are summarised as follows; The first approach is to measure all individual branches with trailing hoses or barometers to get individual pressure drop and flow per branch and then calculate individual resistance factors for input into the software. The simulator is run, checking that the output makes general sense (check some sensitivities if possible). The network is now considered as verified. The pressure drop to be measured is relatively small and thus it is inherent that the measured set of individual K factors will be imprecise no matter how much care is taken in the measurements and the resultant simulations will inherit the same problem. In the second approach, the network is assembled using estimated (Atkinson) K factors (based on physical features of airway, past experience and catalogued typical K factors). Only the main primary flow rates are measured and hence the relative distribution of the primary ventilation in the main airways is determined (probably about 10 off primary air flow measurements). Main critical pressure differentials at main and booster fans and across critical doors are measured (probably about 6 off primary pressure differential measurements need to be made). The simulator is run and the computer model is used to iterate and select an updated suite of K factors so that the flow balances and pressure differentials are correctly simulated (typically only 2 or 3 iterations are all that is needed). The network is now considered as verified. The pressure differences to be measured will be substantial in absolute terms and can be measured with high precision. Also, because only primary flows are measured, these will generally be measured at higher air speed points and hence improved relative accuracy. This leads to more accurate simulation results. This paper examines the advantages and disadvantages of the two approaches. 1 Background

Jan 1, 2009

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By M. Javier

Mining is an industry of experimentation throughout human history. Recently, societies are giving a clear message about mining because many projects are being rejected around the world. These refusals are a generational reaction to the activity of mining. In practice, it generates the perception that mining is using the same methodology without attending to the gradual initiation of conflicts. This is in spite of the best engineering and technology of the time that are put in place at the presentation of those mining projects. Some of these rejected projects are geographically distant from each other, but the communities? rejection occurred during many cases under similar characteristics. This concern shows that the current model of mining projects needs to be replaced with a new one: A new Design, one within which the socio-environmental values of this millennium are inherent. This paper describes Mining Project 101 to help the industry to set the highest and cleanest standards for mining. It also presents its aspects to sustainability and nature, which provides the principles and procedures for designing, planning, and operating mining projects with sensitivity to nature. It offers methods of diagnostic, remediation, and extraction while at the same time preventing and preserving a physical, chemical, and biological equilibrium of nature. This emerging process will be a step up from having a mining industry unaccountable to the socio-environmental conflicts it perpetrates and will abandon the ?cosmetic? repair on the caducity of traditional models in today?s practice. In conclusion, we have the opportunity to change this model. KEYWORDS: Equilibrium in Nature, Geomímic, Deproduction, mine design.

Feb 27, 2013

By Thomas Marcher

Stanford Linear Accelerator Center (SLAC) is located in Menlo Park, CA. In order to allow for enhanced experiments, the current facilities required expansion. Tunnels were excavated through very weak sedimentary rock interspersed with uncemented zones (Ladera Sandstone) employing the principles of the NATM. The overburden var-ied from 10 to 80 feet. The paper addresses the characterization of Ladera Sandstone that can exhibit the properties of dense sand and weak rock. The paper focuses on the challenges that were encountered during the NATM initial support design and the construction phase including the geotechnical instrumentation, monitoring and design verification process in particular the excavation of the junction between access tunnel and the FEH cavern (49 ft wide by 32 ft high).

By Carrie Pourvahidi

The California High Speed Rail Authority (Authority) was created by the State of California through legislation in 1996. The purpose of the Authority is to plan, construct, finance and operate a statewide intercity high speed passenger rail system. In 2004 the Authority prepared a programmatic level environmental document in compliance with the California Environmental Quality and National Environmental Protection Acts (CEQA and NEPA).The Authority and Federal Railroad Administration (FRA) were the lead agencies overseeing the development of the environmental documentation. The resulting document includes two volumes and 64 supplemental technical reports analyzing the transportation needs for California and the selection of an approach to meeting the project transportation needs. The Programmatic Environmental Impact Report and Environmental Impact Statement (EIR/EIS) identified High Speed Rail as the most environ-mentally protective, sustainable and economical approach to meeting the state?s projected transportation needs.

Jan 1, 2008

By Rameshwar Sah, Basavaraja Maribasappanavar, Sangamesh Desai, G. Balachandran, Ravi Kant Sagar

The present research work deals with the effective utilization of hematite ore containing goethite, kaolinite and gibbsite losson- ignition (LOI) phases in pellet making without deteriorating product pellet properties by optimizing the induration cycle especially drying and preheating of pellets. Adequate drying and preheating of pellets before sintering is of prime importance to sustain the desired properties of pellets. Green pellets of + 8 to − 16 mm size were prepared in a laboratory disc pelletizer and indurated by varying drying and preheating temperatures in a laboratory Raising Hearth Furnace (RHF). Produced pellets were assessed for physical and metallurgical properties. Improvement in drying and preheating temperature simultaneously helped in mitigating fired pellets’ property deterioration. Drying at 300 °C and preheating at 750 °C helped in the maximum removal of matrix LOI from the pellets before firing and enabled the production of pellets of desired properties. Laboratory scale findings successfully implemented at existing 4.2 MTPA capacity pellet plant of JSW Steel Ltd. Vijayanagar and high LOI iron ores (IOs) utilised which resulted in reduction of average monthly pellet fines generation by ~2 wt. %.

Jun 4, 2022

By Don F. Macfarlane

This paper describes the field application of the NTH fracture classification to rock encountered in the construction of the 9.6 km long, 10m diameter, Second Manapouri Tailrace Tunnel. Excavation of the tunnel was undertaken by TBM between 1997 and 2002, in gneisses, granitic and diorite rocks. The paper outlines an adaptation of the NTH fracture classification used during the geological logging of this tunnel. The NTH fracture classification was primarily applied to assess discontinuity spacing for tunnel support requirement decision-making. The paper includes some general comparison of NTH classes with overall penetration rate.

Jan 1, 2008

By M. Fornaro, E. Lovera, I. Sacerdote

"The analysis of the mining laws of the different European States reveals big diversities and, often, remarkable complications. This is due, firstly, to the history and culture of different States and, secondly, to the assets of natural resources. It is therefore difficult to find a common line between the text of the various mining laws, but it can be observed that nearly all the States distinguish the mining resources in two categories: the materials whose importance is considered strategic belong to the first category; in the second category the materials whose importance (above all economic) is mainly local are comprised. The paper, analysing in detail the planning procedures in some important Countries, investigates the possible perspectives of arranging some guide-lines for a correct approach to the sustainable exploitation planning/programming of mineral resources (with particular reference to "quarry" materials, such as aggregates), considering both the environment protection and the production needs."

Jan 1, 2005

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By E. M. Frizzell

It is unlikely that improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel cost/shortages, and increasing haul distances as in the past. Therefore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this Bureau of Mines contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic, and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data were gathered from extensive literature searches, European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configurations.

Jan 1, 1979

By Ö. Kaya

The removal of gangue minerals from three different graphite ores (Inebolu, Akdag?madeni and Çoraklidere) from Turkey by acid leaching was studied. Acid leaching experiments were applied to the flotation bulk concentrates, which were obtained in determined optimum conditions after preliminary flotation tests. The effects of acid type, acid concentration, leaching temperature and leaching time on the dissolution of gangue minerals were studied. The most suitable leaching conditions were determined to be 20% HCl + 4% HF for acid type and concentration, 85 ºC for leaching temperature and 4 hours for leaching time. After removing the gangue minerals at these optimum conditions, the total carbon contents of the samples from Inebolu, Akdag?madeni and Çoraklidere increased from 23.51% to 40.07%, from 37.93 to 60.47% and from 42.28 to 59.47%, respectively.

Jan 1, 2009

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By Carlos Henrique Turolla Maia, Ulrich Maidl, Marc Comulada, Julio Claudio Di Dio Pierri

"Pure sands are typically the domain of slurry shields due to their high permeability and their granular characteristics. However, the Earth Pressure Balanced (EPB) shield machine technology has advanced in recent years with improved conditioning agents and shield machines that are equipped with slurry injection facilities and alternative mucking methods. These new so-called hybrid EPB machines have steadily increased the range of application of the EPB technology. The contribution discusses the capacities and operational features of hybrid EPB vs. slurry shield technology in pure sands. At the example of the Metro Line 4 in Rio de Janeiro (Brazil), the contribution shows that hybrid EPB tunneling in pure sands is possible and it is compared with a state-of-the-art slurry shield project as the KASIG project in Karlsruhe (Germany). Furthermore, the control of the support pressure by means of foam conditioning and slurry injection in conjunction with a close, real-time monitoring of machine parameters is discussed. INTRODUCTION Slurry shield and EPB technologies have both undergone significant developments in recent years, leading to the use of parts of one technology in the other and even to completely hybrid systems. Also the ranges of application (see recommendations by DAUB (DAUB 2010)) of both technologies have been shifted far beyond their original limits and are largely overlapping by now. Nevertheless, the basic principles of face support remain unchanged. Exploiting the possibilities of process data analysis (Maidl 2014), the interactions between the ground and the shield machine are a matter of research and have been intensely investigated. PRINCIPLES AND CALCULATION OF FACE SUPPORT PRESSURE Figure 1 shows the principles of two approaches for the determination of required support pressures: kinematic methods and numerical methods. Kinematic methods that are employed for the assessment of face stability only consider the situation in front of the TBM. The required face support force is determined by means of an assumed failure wedge that would form in ultimate limit state. Based on the ground properties, the vertical surcharge and the self-weight is transformed into a horizontal force along a virtual sliding surface. This horizontal force is to be balanced by the face support. The calculation results are amended by respective partial safety factors for water and earth pressure and the method-specific support pressure fluctuations are added."

Jan 1, 2016

By Rex E. Loesby

The dramatic increase in molybdenum prices from the low of less than $2.50/lb in 1999 to more than $40/lb in 2005 has caught the attention of molybdenum mine owners and exploration project developers. Between 2005 and early 2007, prices pulled back and stabilized within a trading range of $25/lb to $30/lb. This 1,000 percent price increase has motivated most existing producers to expand production and is motivating those with molybdenum prospects to accelerate the development process for earliest possible production. It is still unknown how much new production will come from existing mines, how much production will be needed from new mines if demand continues to grow and how many potential new mines might be available to meet future demand. And of course, the billion dollar question is whether molybdenum prices will remain high, or will they fall back to the low levels seen during the 1980s and 1990s? This article attempts to answer these questions in a way that will help molybdenum project developers and financiers plan for the future.

Jan 1, 2007

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By Enrique Hermana, Raymond F. Dalton, Raymond Price, Barry Hoffman

Introduction Chloride leaching of sulfidic ores has been known about for 100 years. It is recognized as a highly efficient process to produce concentrated leach solutions. Despite this, chloride leaching found little practical application until recently because of the highly corrosive nature of concentrated chloride solutions. This situation changed with the advent of modern construction materials such as GRP, polypropylene, butyl rubber, etc. And in the past 20 years, research has burgeoned in the area of chloride hydrometallurgy. The research impetus stemmed from the belief that chloride leaching can provide an alternative to smelters for treating conventional copper concentrates. In addition, chloride leaching was thought to be suitable for on-site refining of copper at small tonnage operations located in remote areas. And chloride leaching was seen as a logical choice for treating unusual or complex concentrates that smelters could not handle. Underpinning these beliefs is the attraction of chloride-based hydrometallurgical processes for sulfidic ores. Sulfur is liberated in the environmentally acceptable elemental form rather than as sulfur dioxide. Consequently, sulfidic copper ores have received much attention. A review of Edmiston in 1984 describes 12 chloride-based processes. All managed to progress past the "laboratory beaker" stage of evaluation. In nine of these processes, copper is recovered electrolytically. Key features of these processes are summarized in Table 1. Table 1 shows that the processes must include a copper solvent-extraction step. Only these processes produce a clean copper electrolyte capable, with no further refining, of directly producing high quality cathode copper. The ICI/Elkem process is the exception here. The rest of these processes use o-hydroxyaryloxime reagents for the solvent extraction of copper and are constrained by the performance of these reagents. This is governed by hydrogen ion concentration (Equation 1). The practical result is that only relatively dilute copper solutions can be treated (Canmet, Phelps Dodge), or careful pH control or adjustment is necessary (Minimet Recherche, B.H.A.S.). This negates one of the attractive features of chloride leaching - its ability to produce very concentrated copper solutions, up to 40-45 gl-1. [ ] In all four processes using o¬hydroxyaryloxime extractants, solvent extraction transfers the copper from the chloride to the sulfate medium. To minimize cross-contamination of the two anions, the loaded organic solvent has to be scrubbed to remove the chloride ion. This represents an additional complication in the solvent extraction circuit. And it

Jan 1, 1988

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009