Search Documents

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

Basic parameters affecting the stability of foams have been studied. We used the thin film pressure balance (TFPB) technique of Scheludko and Exerowa (1959) to measure the surface forces in foam films stabilized with various frothers such as pentanol, octanol, MIBC, and PPG. The results were compared with the froth stabilities measured using the shake tests and the film elasticity calculated using the model developed by Wang and Yoon (2006). It was found that the froth stability is controlled by both film elasticity and surface forces (or disjoining pressure), the relative contributions from each changing with frother concentration and type.

Jan 1, 2006

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

The status and outlook for mining, in your view. Minerals remain a major part of the world’s economic foundation. The fortunes of the mining industry rise and fall with general economic trends, but mining is no less important today on a global basis than it has been historically. Certainly, portions of the industry are critically depressed — domestic copper to name one area —but other sectors are prospering. Mineral consumption, both worldwide and in the United States, has increased steadily since the Great Depression, hitting all-time highs in 2000, the last year for which I have seen data. The highly developed economy in the United States tends to obscure the continuing importance of minerals here. But in less developed nations the critical nature of minerals is obvious and well accepted. In short, although there is no shortage of problems or challenges facing mining — there never has been — mining remains an essential business with great global opportunity.

Jan 1, 2003

By Kazuo Magata, Hirohiko Fujita, Masazumi Tashiro, Yoshiaki Sato, Yoshio Shinoda

The Shinkansen of the Japanese National Railways (JNR) presently in operation between Tokyo and Hakata, approximately 1,000 km, was constructed at three stages: between Tokyo and Shin-Osaka opening in 1964, Shin-Osaka and Okayama in 1972 and Okayama and Hakata in 1975. Works on the extension of 400 km from Okayama to Hakata were launched in March 1970. As construction of the undersea Shin-Kanmon Tunnel on the extension was the toughest task, requiring many, many months, the work was undertaken earlier than any other works on the extension. It was brought to its completion in June 1974 at the cost of about 22, 000 million yen. The Shin-Kanmon Tunnel is the third undersea tunnel constructed to connect the main island of Honshu and Kyushu across the Kanmon Straits. (Table 1)

Jan 1, 1976

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By Anthony D. Hammond

The use of geographic information systems (GIS) as a tool to analyze and display data is gathering momentum in the mining industry. Of particular interest is the capability of GIS to link spatial features and tabular data. The application of GIS in underground mining discussed here concentrates on four technical areas. They are land ownership and mineral claims, exploration management, production and mine safety.

Jan 1, 2002

By Morris T. Worley

Editor’s note: Mining companies doing business in Central Asia, and parts of the developing world, should look for ways to promote community development through the introduction of appropriate technology. This article should be of interest to SME members. It shows sustainable development type projects need not be massive or expensive. Smaller, utilitarian projects are equally valuable to developing communities as they seek to develop their own economic and social infrastructures. Joint Development Associates International (JDA) began humanitarian relief and community development in Central Asia in 1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in the company’s efforts to assist those segments of society that are most vulnerable to poverty and disease.

Jan 1, 2005

By Charles W. Axten

Since the mid-1970s, samples of airborne and waterborne fibrous particulates have been collected in the area of the Northshore Taconite Ore Processing Facility by the Minnesota Department of Health (MDH), the Minnesota Pollution Control Agency (PCA), and the University of Minnesota. Indirect sample preparation has consistently been used although other aspects of the sampling methods and sites have varied and analytical procedures were altered over time as more accurate and precise microscopy methods were developed (i.e., phase contrast optical microscopy, transmission electron microscopy, transmission electron microscopy with energy dispersive spectroscopy). In the mid-1970s, levels of airborne fibrous particulate in the Silver Bay area averaged from 0.00030 to 0.03 f/ml. This level was significantly greater than levels of similar particulates in the St. Paul, MN area, although two of the Silver Bay sampling sites, considered individually, did not indicate levels of fibrous particulate markedly different than that seen in St. Paul. More recent sampling data (i.e., 1990?2001) indicate mean concentration of airborne fibrous particulates (amphibole-like fibrous particulates) of 0.0020 f/ml with a range of values from 0.0001 to 0.0140 f/ml. Such levels are not significantly different from those seen in other non-urban environments in the US and Europe. Concentrations of fibrous particulates in water samples were higher in the mid-1970 when iron ore tailings were being deposited in Lake Superior, but since the tailings have been deposited on land waterborne levels of fibrous particulate in the Beaver River have remained relatively constant averaging in the range of 7.5 MFL. This level is only slightly in excess of the current EPA drinking water standard for fibrous particulates. Review and consideration of this data is important in determining the potential health risks associated with airborne and waterborne fibrous particulates in the areas of the Northshore Taconite Ore Processing Facility. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Asbestiform fibers; Fibrous particulates; Cleavage fragments; Phase contrast optical microscopy; Transmission electron microscopy

Jan 1, 2007

By D. Craig Camp

conditions. The soils included 65 m of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2, 130 meters of soft clay, silt, and sand not exceeding 30standard penetration test SPT blows per 300 mm, and 220 m of rock ranging between an UCS of 400-600 kgf/cm2. The river crossing, utilizing 1778 mm OD x 19 mm wall x600 mm steel casing pipe without intermediate jacking stations, was part of a seven kilometer liquefied natural gas (LNG) transmission line in South Korea. This 440-m, 1,442-ft, river crossing was microtunneled through three different ground conditions and completed in just over three months. The crossing was achieved with an average of 25 m of ground cover and 15 m of water cover. The Kwang Yang River Crossing was part of a 7 km liquefied natural gas pipeline project for POSCO, a Korean steel producer. The microtunneling machine was custom built for this project. The microtunneling machine selected for this project was tooled with 7 button bits and 2 roller bits. None of the cutter bits were replaced during the drive. Inside the machine, before the spoils laden slurry was pump back to the surface, it would pass through an independent cone crusher. The crusher is placed in the slurry flow to make sure that none of the spoils are so large as to stop the return flow of the slurry. An additional requirement was for the inclusion of a compressed air lock. The air lock was required in the event that the cutter tools required replacement. The cutters were back loaded so that the workers would have access to change the cutters in the event of cutter failure or wear out. No intermediate jacking stations were installed for the drive. The soils included 65 meters of rock not exceeding an unconfined compressive strength (UCS) of 200 kgf/cm2 with production averaging between 7 and 20 mm/minute. The second zone contained 130 meters of soft clay, silt, and sand not exceeding 30 standard penetration test (SPT) blows per 300 mm with production averaging between 80 and 180 mm/minute. The third zone contained 220 m of rock ranging between an UCS of 400-600 kgf/cm2 with production averaging between 7 and20 mm/minute. The steel casing pipe was 1778 mm OD x 19 mm wall x 6000 mm long. The project profile, see Figure 1, shows the soil conditions. The hand written numbers locate just above the pipeline are the production dates. The circled numbers are the 10 pipe joint increments. The project required 74 pieces of pipe to span the440 m drive. Figure 2 and Figure 3 are the jacking information. Figure 3 is a continuation of the information from Figure 2. The top section of the graph is the jacking force. The jacking

Jan 1, 2001

By Charlie Yates, Max Ramey, Kurt Nielsen, Michael Hardy

The Yankee Gulch sodium minerals project (YGP) is a solution mining project operated by American Soda. The mine operates on a federal lease administered by the U.S. Bureau of Land Management (BLM). Commercial operations began in November2000. In 1964, Irv Nielsen discovered nahcolite mineralization where the YGP pilot plant is now located near the Piceance Creek in Rio Blanco County, Colorado (Nielsen, 1969).Development of the project accelerated after Williams Corp., of Tulsa, OK, joined with American Alkali in1996 to form American Soda. Pilot testing by American Soda led to commercial permitting, plant design, construction and startup. Figure 1 shows the location of the Yankee Gulch leases and the location of the upper and lower plant sites.

Jan 1, 2003

By N. D. Policow, J. S. Orphanos

D.A. Dahlstrom In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in Fig. 4. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in Fig. 4. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensors, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89¢/t (81o; per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed. ? Reply by N.D. Policow From a technical standpoint, a number of extensive test programs have demonstrated that by raising the feed temperature, mechanical dewatering is enhanced whether it be centrifuges or filters performing the separation. Economic constraints usually become the over-riding issue. If an inexpensive source of thermal energy is available, i.e., waste steam, etc., the approach becomes commercially acceptable. For the specific case of coal slurry pipelines, since the dewatering plants will be located close to power generation stations, the preheating approach becomes especially attractive. The cost comparison shown in Fig. 7, which was prepared by a major West Coast engineering firm, contrasted screen bowl centrifuges and disc filters. In both alternatives, a thermal dryer was specified to produce a contract moisture of the final product. Sizing of the thermal dryer on the screen bowl alternative was substantially smaller than that of the filter, since the screen bowl was credited with a four to six percentage point decrease in product moisture compared to the disc. This comparison was made at ambient temperatures and reflected solely the mechanical dewatering capabilities of the two devices. No preheating of the feed was included in this particular comparison. Early generation screen bowl centrifuges operated under the principle of maximum bulk tonnage throughput. Second and third generation machines have followed the trends dictated by the coal industry calling for higher one-pass recoveries than previously demanded. The current generation of high-speed, long-bowl centrifuges permit recoveries of ultrafine solids directly comparable to commercial filter operation. On typical coal preparation plant feeds with nominal 600 E. an X 0 (28 mesh X 0) clean coal, recovery levels in excess of 99% are now obtained. The material that does escape the centrifuge and reports to the main effluent is typically -10 µm, high ash material. We have documented substantial beneficiation effects in screen bowl centrifuge performance with the cake product containing lower ash levels than the feed. On the referenced pipeline, coal tests performed on Western subbituminous coal, we found that the percentage of -10 µm material in the feed was six to eight times greater than normally encountered on eastern Appalachian seams. Our 45-t/h (50-stph) production centrifuge was never set up to maximize recovery. It was used as part of the two-stage dewatering circuit that had been chosen by designers of the proposed pipeline. Recoveries up to 95% were recorded. With field adjustments, that performance could most certainly have been improved. In contrast, manufacturers of the horizontal belt filter provided a small pilot-scale unit that operated on a side stream at the test facility. Numerous combinations of chemical additions were evaluated to determine those that had the best impact on filter performance. Whereas the screen bowl centrifuges operated without chemical addition, producing a dry, fluffy cake, the belt filter required two stages of chemical addition to attain satisfactory performance and high recovery levels. On the two-stage circuit that incorporated a belt press as the secondary

Jan 12, 1983

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By R. M. G. S. Berezowsky

An atmospheric ammoniacal thiosulphate leach system was developed to recover gold and silver from residues of the ammoniacal oxidation leaching of sulphidic copper concentrates. Extractions of 88 - 95% Au and 83 - 98% Ag were attained within 2 to 4 hours at 40 - 60°C in thiosulphate leaching of the oxidation leach residues of Manitoba chalcopyrite concentrates analyzing 24.6% Cu, 0.18 oz/ton Au and 4.26 oz/ton Ag and a complex British Columbia chalcopyrite/tetrahedrite concentrate analyzing 18.5% Cu, 0.27 oz/ton Au and 276 oz/ton Ag. Parameters affecting the Au and Ag solubilization included thiosulphate, ammonia, and cupric ion concentrations, temperature, retention time and the degree of Cu extraction and sulphide oxidation in the primary oxidation leach. The precious metals were recovered from the thiosulphate liquors by zinc dust cementation.

Jan 1, 1979

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two o f the pit lakes, 26- and 55-m (85 and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper, pit lakes, 110 and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1997

By F. Habashi

The phosphate fertilizer industry is at present based mainly on the use of sulfuric acid. This technology results in the generation of large amounts of radioactive gypsum that represents disposal and environmental problems. Also it involves the use of expensive reactors for acidification that necessitates the frequent replacing the damaged agitators. Applying hydrometallurgical techniques such as in-situ, heap, or vat leaching to phosphate processing could solve these problems. In this case, however, nitric acid must be used and dicalcium phosphate (40% P2O5) may be obtained as a final product. It is insoluble in water but soluble in citric acid and is an excellent fertilizer. This technology does not interfere with uranium recovery if desired. In addition it permits the recovery of rare earths which are otherwise lost in the gypsum.

Jan 1, 2011

By Michael Harris, David Mosch

The numerous small high grade gold and silver deposits of the Front Range Mineral Belt have been uneconomical because of the high costs of mill construction, transportation, and smeltering. Processing of these ores must be simple, cheap, with satisfactory recoveries, and be environmentally acceptable. Vat leach with direct electrolytic recovery satisfies these parameters. A battery of testing was conducted utilizing bottle and bucket tests. A five ton vat leach with direct electrolytic recovery gave excellent results while a five ton heap leach proved impractical due to channeling.

Jan 1, 1987