Search Documents

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

Several economic factors have caused the surface mining industry to require large-capacity shovels and trucks for efficient, high-production, low-cost operations. Some of those factors include technological advancements in equipment, commodity market depressions, increased labor and maintenance costs, contractural obligations and harsh operating conditions. The difficult operating conditions in surface mines, however, pose challenges to the use of high-capacity equipment. They include space limitations, weak over-burden, and weathered soils and rocks. So mining companies face major challenges in selecting appropriate shovels to meet the technical, operating, safety, environmental and economic requirements of their mines.

Jan 1, 2003

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

By Raymond L. Lowrie

Deregulation, as authorized by the Energy Policy Act of 1992 (PL102-486) allows free-market competition in the electric-utility industry. As the act unfolds, though, uncertainties abound about the type, degree and direction of impacts throughout the affected economy — from fuel suppliers to electricity generators and from power distributors to energy consumers. Instead of having a familiar base of captive customers and electricity prices fixed by negotiation with state public utility commissions, utility companies are preparing for open, free-market competition. They are looking at all areas, including fuel supply, to cut costs to remain competitive. Humorous anecdotes are told about utility companies shunning insiders for senior executive positions. Instead, they are opting for people from the telephone or other industries with deregulation experience. And there are light-hearted stories about a trend away from traditional electric-company names, such as the name of a city or state followed by Edison or Power and Light, to space-age names, such as Ameren, Entergy, Illinova or Unicom. No one wants to be left behind or be perceived to be left behind.

Jan 1, 1996

By James Wm. White

Computer-based mine management systems are being used in many surface mines to assign haul trucks, track equipment and manage information. Advances in digital communications allow these systems to be used in underground operations. Underground mine management systems help maximize production by providing gains in equipment and manpower use, drawpoint equalization in block caving operations, preventive maintenance and safety. Current systems use allocated or "locked" train and load-haul-dump (LHD) dispatching. Allocated dispatching rarely optimizes open pit product' on. But it offers an efficient mode of operation underground and where options are more limited. The primary objectives of underground mine management systems are to maximize production and mini¬mize contention time through allocated train, truck or LHD dispatching, traffic control, equipment monitoring and comprehensive reporting. The main components of an underground mine management system include: ? A central computer (personal computer or worksta¬tion) in a central control center. It sends instructions to train, truck or LHD drivers and allows dispatcher interaction. ? A field computer system (FCS). This consists of a touch-screen graphics console (GC) and mobile hub - on each train, truck or LHD to receive and display instructions from the central computer and accept driver input. ? A data radio network based on leaky feeder (data, voice, video) or microcell radios (data only) and advanced token-ring technology. This passes information between the central computer and the FCSs. ? Radio frequency (RF) tags mounted at boxes, weigh bridges, tips and rim tunnel main haulage ways to locate trains or LHDs (Luke, 1993). Such a management system must be in place before implementing computer-based dispatching (Vagenas, 1991) for production optimization.

Jan 1, 1997

By Vladimir G. Kochnev

Crushing and grinding account for the major portion (60 to 80 percent) of the overall expenses for ore processing. Autogenous (AG) and semiautogenous grinding (SAG) have been considered a step forward in comparison to conventional grinding circuits with several stages of crushing and using ball (and/or rod) grinding mills (Bassarear, 1982, MacPherson, 1989, Pithois, Casalis, 1983, Maripuu et al., 1983). However, there remains room for improvement to existing AG and SAG technologies and both technologies have immense economic benefit potential. Experience gained by the Technics & Technologies of Disintegration Ltd. (TTD) in the research of grinding processes shows that grinding in AG and SAG mills can be performed in a more effective way. The company's approach comprises the following elements: ? Novel mill design. ? New liners and lifters. ? Novel discharge grid design. ? Technique of treating material of critical particle size. Comparative tests that demonstrated the usefulness of these innovations are described in this article. Currently, there are hundreds of AG and SAG mills in operation throughout the world. Application of new internal elements of the mills and reconsideration of the circuit design of the existing grinding equipment using present technological solutions would significantly increase the throughput rate and diminish power requirement.

Jan 1, 2008

By Lane White

Refractory gold ores are those from which a significant percentage of the gold cannot be recovered by conventional cyanidation. Historically, roasting has been the primary method for rendering such ores amenable to gold extraction; however, roasting creates environmental problems that are not acceptable in many locations. During the 1980s, consistently strong gold prices drew increasing attention to refractory gold ores, and new processing schemes were commercialized, most prominently aqueous pressure oxidation and more recently bacterial oxidation. Since 1985, pressure oxidation has been incorporated into four plants processing refractory gold ores. A fifth plant is scheduled for start-up in early 1990, and three additional plants are scheduled for production before late 1992. A technical session on treatment of refractory ores was included in the program of `World Gold '89, a Gold Forum on Technology and Practices' held by SME and the AusIMM in Reno, NV, Nov. 5-8, 1989. This article summarizes material from five of the papers presented during the refractory gold session and published in the proceedings of `World Gold '89,' edited by Roshan Bhappu and Rod Harden. The complete proceedings are available from SME Publications Sales, P.O. Box 625002, Littleton, CO 80162-5002 $53.50 for members, $38.50 for student members, and $73.50 list price.

Jan 1, 1990

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

By B. Caro Vargas

The Toulon Tunnel project is a key component of the highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960s. The tunnel project is comprised of two separate tunnels: south and north. The north tunnel was built between 1992 and 2002 after 10 years of difficult construction. On March 15, 1996, for example, a collapse of the tunnel in the Marchand area generated a sinkhole in the city center, causing a 20-month delay. The south tunnel alignment runs parallel to the north tunnel below Toulon?s historical downtown at a depth of 20 to 40 m (65 to 131 ft) with some areas with less than 10 m (32 ft) of cover. The risk management program was studied to be a state of the art program in urban tunneling construction.

Jan 1, 2012

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit, in Yemen, contains at least 9.4 Mt at a grade of 10.7% zinc, 2.2% lead and 77g/t silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to conventional smelter/refineries, and it has been necessary to formulate a less conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material, at Yanbu, in Saudi Arabia. In order to give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulphide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, the flowsheet for Yanbu and presents preliminary costs for both operations

Jan 1, 2002

By Greg Sheppard, Eduardo Nebot

Australian researchers have developed new technologies aimed at improving safety and productivity at openpit mines. A data acquisition and feedback system for electric rope shovels has been shown to substantially reduce cycle times and decrease excessive machine duty caused by stalls. This data acquisition system was developed by the Cooperative Research Center for Mining Technology and Equipment (CMTE). It has been tested on a P&H 4100A shovel at Coal & Allied’s Hunter Valley operations and a P&H 4100XPB at BHP Billiton Mitsubishi Alliance’s Goonyella Riverside Mine in Central Queensland. In addition, CMTE member P&H Mine Pro Services has used the technology to acquire field data from a P&H 4100XPBrope shovel at RAG’s Belle Ayr Mine in Wyoming’s Powder River Basin.

Jan 1, 2002

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

While the United States and the rest of the world struggles with record-setting oil prices Canadian oil sands producers are ramping up production to meet demand for oil while also fighting against a host of negative images. In recent months, the price of oil has skyrocketed. Most of that oil comes from Saudi Arabia. In Alberta, Canada there are unconventional oil reserves that rival those in Saudi Arabia in the vast Canadian oil sands, sometimes called the tar sands. Proponents of the oil sands say that Alberta?s oil sands can be a secure source of oil and energy for the United States for many years to come. With new mining and drilling projects, the industry has said that it could quadruple its production to nearly 4 million bbl/day by 2020. Time magazine once called the oil sands, ?Canada?s greatest buried treasure that could satisfy the world?s demand for petroleum for the next century.? So why hasn?t the United States embraced this close, politically secure source of energy? Because, getting usable fuel from the oil sands can be a dirty business, say opponents. The oil sands are a combination of clay, sand, water and bitumen. It is a heavy, black, thick oil. Oil sands can be mined and processed to extract the oil-rich bitumen, which is then refined into oil. The bitumen cannot be pumped from the ground in its natural state. Instead, tar sand deposits are mined, usually using strip mining or openpit techniques, or the oil is extracted by underground heating with additional upgrading. These methods require a huge amount of energy and water and produce a large amount of carbon emissions. Environmental groups that have long spoken out against the oil sands projects got some political backing in the United States in June when a group of mayors from large U.S. cities spoke out against the oil sands, as did presumptive Democratic candidate for U.S. president Barack Obama?s senior energy advisor. During a convention of large-city mayors in Miami, FL, Alberta?s oil sands were singled out in a nonbinding resolution calling for national guidelines to track the lifecycle impact of different types of fossil fuels. The resolution urges cities not to use unconventional sources of energy with a large carbon footprint, such as liquid coal and oil shale and oil sands.

Jan 1, 2008

By Jose A. Gomez, Javad Sattarvand

Failures of tailings dams have been happening lately. Due to the lack of laws on particular design criteria and stability requirements related monitoring during construction and maintenance, they are thought to be more fragile than hydraulic dams. Monitoring the dam is therefore necessary to understand its current condition and guarantee its safety. The physical condition of the dam could be evaluated with the early identification of seepage. Additionally, due to their adaptability and capacity for high-resolution data collecting, UAVs are an excellent choice for efficiently covering the tailings dam site. UAVs may capture high-quality photos when equipped with a high-resolution RGB camera, thermal sensors, or multispectral sensors. When these sensors are paired with image processing and machine learning algorithms, the result is a reliable estimate of the dam condition.

Jun 25, 2023

By V. K. Paruchuri, J. D. Miller, J. Nalaskowski

The phenomenon of surfactant adsorption at mineral surfaces is of significant importance in many particulate processes ranging from mineral flotation and enhanced oil recovery to pharmaceutics, paint technology and the casting of high quality ceramics. Stability of the dispersions is related not only to the amount of adsorbed surfactant but also to the structure of the adsorbed surfactant molecules at the interface. This structure greatly depends on the type of surfactant and the hydrophobicity or hydrophilicity of the surface. On hydrophobic surfaces surfactants adsorb regardless of surface charge by van der Waals/hydrophobic inter-actions with hydrocarbon chains accommodated at the surface. On the other hand, on hydrophilic surfaces the surfactants adsorb through electrostatic interactions with their polar moiety fixed at the surface. In the latter case, the electric charge of the surface and surfactant plays a crucial role in the surfactant adsorption process. The recently developed soft-contact Atomic Force Microscopy technique has revealed images of adsorbed surfactant structures at various interfaces. The adsorbed structures of a cationic surfactant (CTAB) and an anionic surfactant (SDS) are presented in this work for different concentrations at hydrophobic graphite and hydrophilic mica surfaces. Different types of micellar arrangements have been observed at these surfaces for surfactant concentrations around the critical micelle concentration. The structures are more ordered and well defined at the graphite surface than at the mica surface. These results have been correlated with the hydrophobicity of the surfaces as revealed by contact angle measurements.

Jan 1, 2001

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985