Search Documents

By A. B. Hazar-Yoruç

Ferrochromium produced by smelting chromite ores is an important alloying component in the steel industry. Ore, coke and fluxes are mixed and reacted in an arc furnace for a smelting process of ferrochromium. In ad-dition to this process, pre-reduction of chromite ore with carbon is an important industrial process. In all these processes, the mechanism and kinetics of reduction of chromite with carbon play an important role. In this study, the reduction of Turkish chromite ore with carbon was investigated. Chromite and carbon were ground to three different particle size groups. Chromite was mixed with carbon in stoichiometric and excess ratios. The samples were reduced under argon atmosphere at temperatures between 1,200° and 1,350°C. The formed phases and alloy compositions of reduced chromite samples were analyzed by optical microscopy, scanning electron microscope (SEM) with EDAX and X-ray diffraction analysis (XRD). Experimental results showed that the degree of reduction and the reduction rate increased with increasing temperature and decreasing particle size. The highest degree of reduction, 61.4%, was obtained at 1,350°C. The reduction took place in three stages: Stage 1: transformation of Fe3+ to Fe2+ and formation of metallic nuclei, Stage 2: formation of metallic crust around the particles and Stage 3: growth of the metallic crust and coalescence of the metallic phase.

Jan 1, 2007

By W. Hustrulid

"In recognition of his inspiring dedication to the mining industry through education, research contributions and dissemination of practical knowledge, exceptional leadership and excellence in mining engineering practice and for his lecture, “You can't make a silk purse out of a sow's ear.” Recipient of the 2002 D.C. Jackling Award Introduction It is always difficult to decide on the most appropriate title to give to a paper or talk. It is a particularly difficult decision in the case of the Jackling Lecture, because the title becomes part of the award citation. I hope that the significance of this unusual title will become crystal clear as you read the pages that follow. However, to assist you in this journey, I will provide the following few words of guidance. In making a cake, you need the proper ingredients. If one or more of them are missing, it will not be a cake. In addition, the quality of the cake depends on the quality of the ingredients. In my lecture, the "cake" is the U.S. mining industry of the future. A national perspective President George W. Bush in his State of the Union Address (Bush, 2002) delivered on January 29, 2002, defined three national objectives: •win the war on terrorism, •protect the homeland and •revitalize the economy. Under the heading "revitalize the economy," he indicated the importance of "good jobs" and "energy production" by saying: "Good jobs begin with good schools. Good jobs also depend on reliable and affordable energy. This Congress must act to encourage conservation, promote technology, build infrastructure and it must act to increase energy production at home so America is less dependent on foreign oil." I wish that he would have broadened his focus and stated instead that: "This Congress must act to encourage conservation, promote technology, build infrastructure, and it must act to increase materials production at home so America is less dependent on foreign sources." With regard to jobs, all jobs are not equal. To paraphrase John Reeves of MidContinent Resources (Reeves, 2002): "If our nation is to prosper, we all cannot make a living by doing each other's wash. Some of us, at least, must be actively engaged in the primary production of raw materials from the riches of the earth and other Americans must turn those materials into consumer products." The unfortunate trend in our country has been to neglect the primary production of basic materials, even those coming next in line. We have left those responsibilities to others while we concentrate instead on performing various services, i.e., doing each other's wash and flipping burgers. This cannot continue. It must be remembered, especially by those in leadership positions, that all "jobs" are not created equal. Some jobs are much more essential to the security and wellbeing of our country than others. We must be sure that the important ones are in place. We cannot produce the basic materials that our nation requires without access to those materials. This leads to my Proposition 1: You cannot have a viable mining industry without a clearly enunciated, positive U.S. materials policy. Background regarding U.S. materials policy Resources for freedom. In January 1951, President Truman created the President's Materials Policy Commission, with William S. Paley as chairman. As expressed in the invitation letter from the president to Paley: This commission, within the executive office of the president, is to study the broader and longer-range aspects of the nation's materials problems as distinct from the immediate defense needs. The task of the commission is to make an objective inquiry into all major aspects of the problem of assuring an adequate supply of production materials for our long-range needs and to make recommendations that will assist me in formulating a comprehensive policy on such materials. The commission should study, together with any other aspects deemed by it to be pertinent, such questions relating to production materials as: - the long-range requirements outlook; - the long-range supply outlook; - the prospect and estimated extent of shortages; - the consistency and adequacy of existing government policies, plans and programs; and - the consistency and adequacy of private industry practices.

Jan 1, 2003

By C. -G. Zhang

This paper presents the results of a study on cellular acclimation of Acidithiobacillus ferrooxidans to sulfur biooxidation in terms of cells growth and changes in surface properties and morphologies of both cells and sulfur particles. The results showed that A. ferrooxidans cells were grown faster and demonstrated higher concentration in the soluble thiosulfate substrate than in nonsoluble hydrophobic S0 substrate. The results showed that A. ferrooxidans cells acclimated to the sulfur biooxidation by actively expressing some extracellular polymers substance and maybe some outer membrane proteins that modified the surface properties of both sulfur particles and the cells themselves. In addition, the results showed that the A. ferrooxidans cells were able to dynamically adsorb to or desorb from the surface of sulfur particles. The cells aggregating onto the S0 surface enhanced the use of S0 substrate by the bacteria cells. This mode may be one of the most important characteristics for the better growth and propagation of the cells in solid sulfur-containing media.

Jan 1, 2009

By K. R. Griffin

Explosions in underground coal mines have been a serious safety concern since the advent of mining; despite significant technological advances, they are still occurring. Parameters such as barometric pressure, geological changes, and changes in ventilation can contribute to an explosion. These factors can be monitored with available and developing technologies to create algorithms that predict when explosions are more likely to occur. This paper reviews current underground atmospheric monitoring systems and related regulations around the world. In addition, suggestions for improvement and implications for explosion prevention are discussed.

Jan 1, 2011

By Christopher J. Bise

INTRODUCTION Traditionally, the purpose of mine ventilation has been defined as diluting, rendering harmless, and sweeping away hazardous gases which may accumulate in the mine workings. In addition, the ventilation sys- tem must keep the mine air as close as possible to the composition of the outside air in order to provide a healthy environment for mineworkers and to prolong the useful life of mine equipment. When plans are being developed for opening a new mine, sound engineering dictates that a calculated estimate be made of both the maximum air quantity requirement and the accept- able mine pressure (head) loss related to the under- ground layout and projections. For efficient mine ventilation, the two problem areas that demand constant attention are (1) the control of fugitive air (through short circuiting or leakage) and (2) the provision of ample airway capacity. Fugitive air is that quantity of air which enters the mine but short-circuits the mine ventilation system through improperly constructed stoppings, doors, overcasts, etc.; it represents an investment in power consumption (to move the air by the fan) while providing little, if any, return on the investment. Typically, efficient mines are those that can deliver 50% of the air handled by their fans to the working faces. Paying close attention to a new mine's ventilation system at the outset can provide numerous benefits during the later stages of mine development. It has often been noted that the main cause of trouble in many mine ventilation systems can be found within a radius of 2500 ft from the fan installation. Ample airway capacity is essential to maintain the mine's head loss within manageable limits. Similar to an industrial ventilation setting, the mine's headings are the ductwork for the handling of air. The difference between normal industrial ventilation and mine ventilation is apparent when more capacity is needed; a plant can install new or larger ductwork, but it is difficult for a mine to install new entries or enlarge existing entries. Air velocities are usually maintained under 800 fpm to limit the stirring up of dust in the intakes. With this in mind, it is usually simple to estimate the number of entries required in the ventilation system. The problem that often arises, though, is when the system's capacity is overestimated and the required head loss to achieve the desired quantity is excessive. Experience has shown that problems are often encountered when the mine's condition requires much more than three inches of water gage to ventilate the mine on a day-to-day basis. Thus, if proper attention is not paid to these parameters in the preplanning and initial development of a new mine, it may take an extremely high water gage to achieve the ultimate quantity. This chapter will not delve deeply into the theory of mine ventilation; many other books have been writ- ten on that subject. Instead, the following sections will point out the important considerations that should take place before the development of a mine ventilation system, as they relate to normal industry practice. FUNDAMENTALS OF AIRFLOW Volume Versus Water Gage The common method of measuring ventilation pressure is in terms of inches of water gage (wg); one inch of water corresponds to a pressure of 5.2 psf (pounds per square foot). Further, airflow follows a square-law relationship between volumes and pressures where, as shown in the previous section, a doubling of quantity requires a quadrupling of pressure. Table 1 shows how heads and quantities are related. Using Table 1, it is readily apparent that, for the same mining conditions, an increase in pressure from one inch wg to three inches wg results in only 34,640 cfm when the initial quantity is 20,000 cfm. Pressure Losses Pressure losses in mine ventilation systems are caused by friction between the heading walls and the air stream and by shock losses due to abrupt changes of the air stream caused by obstructions. The common pressure-loss formula for mine ventilation is: [ ] where H is the pressure loss in inches of water gage, K is the coefficient of friction, L is the length of the airway in feet, 0 is the airway perimeter in feet, V is the air velocity in feet per minute, and A is the cross-sectional area of the airway in square feet. Table 2 lists the US Bureau of Mines schedule of friction factors (K) for mine airways. Recent research indicates that the values of K are slightly less for coal mines than those presented in the USBM Schedule, and Table 3 should be consulted in this instance. It should be

Jan 1, 1986

By Tom Szaraz

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer?Part II (BWOAS) consists of 13,200 feet of tunnel of 12-foot tunnel passing mainly through glacial deposits with a water head of up to 2 bar. A Lovat RME167SE was used to drive this tunnel with steel fiber reinforced precast segmental liner used for support. This paper will discuss the concepts for tunnel sup-port and TBM selection, the problems encountered with the TBM sealing systems and the solutions used to repair the machine.

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By D. W. Partridge, W. Lamb, A. E. Lamb, S. Bird

Due to the constant need to improve SAG mill performance and efficiency, extensive research into all aspects of SAG mill optimization has been performed. This paper will review the current evolution of SAG mill shell liner design and their performance at the Copperton Concentrator. The effect of these liner design changes will be discussed with respect to: • Liner configurations • Mill operating performance, i.e., throughput, power draw, mill control • Mill mechanical performance, i.e., liner wear profiles, liner life, liner breakage, liner hardness • Foundry manufacturing considerations • Economic evaluation of throughput versus liner life This paper will discuss the results of Kennecott Utah Copper’s (KUC) and ME International’s (MEI) test work, providing an insight into the past, present and potential future opportunities of SAG mill liner design.

Jan 1, 2002

The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure to roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations, and trial-and-error testing. Both prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001

By Franziska Wolf, Rainer Ellmies, Helmut Mischo

"Mining is an important part of the economy of Namibia. In 2016, 11.1 percent of the GDP was the result of mining activities with 22 active mines (The Chamber of Mines of Namibia, 2016). Only one of them consists of an underground mining operation.The global annual production of fluorspar is approximately 5.4 to 6.3 Mt (6 to 7 million st) (U.S. Geological Survey National Minerals Information Center, 2017). Okorusu has produced on average about 45 kt/a (50,000 stpy) in recent years (U.S. Geological Survey National Minerals Information Center, 2015).The Okorusu Mine is Namibia’s only fluorspar mine. Fluorspar was mined in an openpit mine with four individual pits (A-D) since 1980. In 2014, the mine closed due to the increased stripping ratio and beneficiation problems. The mine assets were bought by Gecko Namibia. Currently, Gecko uses parts of the processing plant for beneficiation of graphite from a neighboring mine. Figure 1 shows a panoramic view with the four pits and the mine village.The intent is to develop a concept for the further underground development of the mine. There are still about 6.3 Mt (7 million st) of measured resources left in the deposit, with an average grade of 27.5 percent CaF2. This study focuses on the underground mine design. The above-ground plant and facilities are considered as remaining unchanged.For solving the task to design the mine, a site visit for data collecting was conducted. Resource estimations were calculated based on existing drill data, and consequently, block models were created. The development of the mine design included the selection of the most suitable mining method, mining technology and mine organization. Moreover, some economic considerations are pointed out, followed by a profitability assessment."

Jan 2, 2018

By W. J. Spat

Political risk is an integral part of the mining business in northern Andean countries. Peru, Ecuador, Colombia and Venezuela all have a higher than average political risk compared with other South American countries. Successful operations require good political-risk information, a thorough political-risk-management plan and a strategy to deal with political-risk perception on the part of the investing public. Colombia is perceived as about the riskiest place in the world to do business. A selection of recent headlines reads: “Colombia on the brink” (Economist, 1998), “Colombia’s ship of state is sinking” (Insight on the News, 1998), or simply “Bad news” (US Catholic, 1998). The World’s Most Dangerous Places rates Colombia as “currently the most dangerous place in the Western Hemisphere, and perhaps the world” (Aral and Pelton,1998). And many prospective investors and analysts say to Greystar Resources: “Yes, we love your results, but Colombia?”

Jan 1, 2000

By Brain E. Gombos

The Allen Park Sanitary Sewer Overflow (SSO) Tunnel and relief sewer project, located in the city of Allen Park, MI, is a long-term corrective action designed to bring Sanitary District One?s sanitary system into compliance with its 2005 consent order and service contract with the Detroit Water and Sewerage Department (DWSD). The $20 million project is intended to reduce Allen Park?s wet weather discharges to DWSD, reduce bypass pumping to the Ecorse Creek and limit the future risk of basement flooding by providing storage during wet weather events and eliminating hydraulic bottlenecks in the sanitary sewer system.

Jan 1, 2013

By Helmut Hass, Michael S. Shultz

For many tunneling, deep shaft and deep excavation projects ground freezing is one of the best if not the only technique available to create a watertight and load bearing temporary support system in soft ground conditions. When appropriate attention is given to the details of the ground freezing system design, ground freezing is a very safe method and is economically viable with competing techniques and combinations of techniques. Recent innovative uses of the technique in Europe are highlighted in this paper and compared with current uses in North America.

Jan 1, 2005

By D. P. Richards

Tunneling in carbonate sedimentary rocks such as lime stones and dolomites can be difficult when solution channels or voids are anticipated. Addressing the risk aspects associated with these formations can be done effectively through the Geotechnical Baseline Report (GBR) by properly characterizing the ground and ensuring that the Owner?s and the Contractor?s interests are represented and protected. This paper presents a review of tunneling difficulties in these rocks and includes a review of site investigations, geologic characterization, and presentation in the GBR. Key construction issues are also discussed, including appropriate excavation technology, mechanisms of face support and groundwater control, and quantifying grout takes.

By Bradley V. Johnson, Robert J. Timko, Edward D. Thimons

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has researched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1987

By Shimi Tzobery, John E. Shamma, Samuel Swartz, Gary B. Hemphill

The trapezoidal tapered ring method has made significant progress in recent years for shielded-TBM projects, excavating tunnels with high overburden, strict water tightness criteria, and multiple curve alignments. The selection of compatible tapered rings is critical for successful advancement of the tunnel, assuring efficient installation of rings, as well as prevention of ring damage and excessive leakage. Using experience from the Arrowhead Tunnels Project, this paper describes guidelines for ring selection in tunnel curves, geometric analyses that comply with criteria principals, and provides techniques developed to determine the appropriate relative key position.

Jan 1, 2005

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992