Search Documents

By Leonard G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups: that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mm) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh (< 0.60 mm); in fluidized bed uses, the coal is typically < 8, in. (< 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1 to 2% in. (25 to 63 mm). Coal preparation plants typically work with a coarse size fraction of 6X 1/14 in. (150X32 mm). The past decades has shown a steady increase in the tonnage of coal cleaned, 1 but it seems probable that the next decades will produce much wider applica- tion of deep coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is intimately connected with the size of coal, a systems design engineer will need as much information as possible concerning the size distributions produced by different types of machines and how these can be modified by different ways of operating the machines. In general, the following questions will be of concern: 1.What type of crusher or grinder is best, or most satisfactory, for reducing a given feed size and type of coal to a desired product size? Frequently, the desired product is smaller than some nominal size, but with as few fines as possible, or the fraction in some size range has to be as high as possible. 2. How big does the machine have to be for a given throughput rate? 3. How much electrical energy (or its equivalent) is required per ton of product? 4. How does the size distribution vary with change in throughput rate, and is a control scheme necessary or desirable? 5. Can the size distribution be readily varied if desired? 6. What is the optimum way to operate a machine in a given system? This section will emphasize certain general principles which guide us in answering these questions. PARTICLE SIZING Since particle size and size distribution are the raw information with which we work, it is worthwhile to review the terminology used. In this regard, see

Jan 1, 1991

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By R. E. Utting

INTRODUCTION Until recently, gamma doses had been largely ignored in Ontario uranium mines. This has been due to the assumption that these doses are small and have been more or less unchanged with time and hence their effects have been included automatically in the epidemiological studies that led to the establishment of radon daughter exposure limits. This assumption had to be challenged for two basic reasons. The first was that radon daughter exposures to miners have been progressively reduced over the years due to improved ventilation and ever more stringent regulations, while gamma exposures have presumably remained relatively unchanged. Therefore it must be assumed that the ratio of gamma to radon daughter exposure has gone up. The second reason is more philosophical. It is clearly inappropriate to make judgements on the significance of a potential industrial hazard when the magnitude of that hazard has not been fully assessed. Having decided that some sort of assessment of gamma exposures to uranium miners must be made, it was than necessary to determine how this should be done. Several options were available, for instance: (i) Wholesale personal gamma dosimetry for all mine and mill workers, (ii) Personal gamma dosimetry only for those workers suspected of receiving the higher doses, coupled with area monitoring to estimate the exposures of other workers, (iii) Area monitoring coupled with dose rate times time calculations for all. This would correspond to the generally prevalent method of assessing radon daughter exposures. It was argued that since radon daughter exposures are the major radiological hazard in uranium mines, to invest resources for assessing a lesser hazard to a greater degree of precision was not cost effective. (iv) Since gamma dose rate is related to ore grade, individual doses could be assigned from knowledge of work location and ore grade. Before deciding which of these options would be most appropriate, it was necessary to have some idea of the magnitude of the problem. Very few data were available in the literature and with the exception of a few spot dose rate measurements, and the results of a few gamma dosimeters issued to selected individuals by some of the mining companies, nothing was available. A rule of thumb of obscure origin is often quoted within the industry indicating that gamma dose rates underground will be about 0.25 mR/h per lb/ton or 5 mR/h per % U. This had been used by some to justify neglecting gamma radiation at least for ore grades of the order of 0.1% or 2 lb/ton, on the grounds that gamma dose rates would be of the order of 0.5 mR/h and therefore give rise to annual doses of only about 10 mSv (lrem). That is, it was assumed that gamma radiation was of limited concern compared to the hazard associated with the inhalation of radon daughters. We were thus faced with the situation of just assuming that no regulatory limits were being breached. This situation could not be allowed to continue. A program was initiated to investigate the gamma doses absorbed by uranium miners in three mines in Ontario, and extensive gamma surveys were conducted in the Quirke 2 mine of Rio Algom Ltd, Elliot Lake; Denison Mine, Elliot Lake; and Agnew Lake Mine, Espanola. Negative reaction was received from several mine company officials to the possibility of all miners being required to wear personal gamma dosimeters due to the logistical difficulties involved, and therefore part of the project was aimed at determining if a reliable correlation between gamma dose rate and ore grade in the work location could be deduced, in order that dose rate times time calculations might be used for gamma dose assessments. The results of these programs provided evidence that the gamma dose for some employees in the three mines investigated may be a significant fraction of the current maximum permissible annual dose of 50mSv (5 rem). When combined with radon daughter exposures in the manner recommended by the ICRP at their 1980 Brighton meeting (ICRP 80) the results indicated that some individuals will come close to the resulting limit and may even exceed it. The results also indicate that is probably not feasible to develop a reliable formula for

Jan 1, 1981

By Y. C. Kim

For the past quarter of century, much more effort and research have been expended in developing the "optimum" ultimate pit limit design algorithms and much less to solving the "optimum" open pit production sequencing. However, the potential economic benefit to an operating mine is far greater for the latter than the former. Unfortunately, the problem of "optimum" open-pit production sequencing has not been fully solved to date. This paper first reviews the past and currently used methodologies for developing this sequence. The staggered pit phase geometry problem of advanced stripping and operational constraints such as ore and waste tonnage requirements by period and necessary contiguity of mining faces are the main reasons why the "optimum" production sequencing problem has not been solved as yet. This paper also explains why any method which attempts to simplify the problem using ultimate pit limit design algorithm will fail to reach an "optimum" solution.

Jan 1, 1994

By A. Pincomb

After determining minable acreage, tons are calculated by multiplying minable acreage by average thickness and by a volume-tonnage conversion factor. Converting from tons in the ground to tons sold across the scale takes fines and internally used and wasted stone into consideration, resulting in minimum losses of about 10% for limestone and 15% for sand and gravel. A high degree of certainty about thickness, lateral continuity and geologic character defines proven reserves. Assuming continuity of these characteristics defines probable reserves. By using tpa estimations and annual tonnage requirements, the life of a deposit can be quantified. The decision can then be made regarding the necessity of securing more acreage. Some landowners choose to multiply aggregate price, operating income, or a royalty rate by tons to arrive at a value for their reserves. In doing so they probably overstate the value of their land.

Jan 1, 2003

By Donald P. Richards, David W. Campo, Michel Coudry

This paper presents a review of the grouting works of Line 2 of the Greater Cairo MetroSystem. The Nile River alluvial deposits underlying this ancient city provided for a challenging and sometimes difficult grouting project. Permeation grouting using state-of-the-art computerized grouting techniques, as well as extensive ground treatment by jet grout, was per-formed for soil consolidation and/or groundwater control. During the project, over 425,000m3 of ground was treated, requiring 1.4 million linear meters of drilling and PVC injection pipe, 54,000 m3 of bentonite cement and 230,000 m3 of chemical and mineral grout. In addition, over 70,000 m3 of ground was treated using the jet grout method. Relative to major international transportation projects, the grouting works for Line 2 of the Cairo Metro represent one of the largest worldwide grouting endeavors to date.

Jan 1, 1997

By G. Récoché

For the African continent promoting a sustainable utilization of its mineral resources could be considered as a key determinant to fight against poverty. Sustainable development performance indicators for measuring the economic, environmental and social impacts of mining activity are necessary for drawing up policies and sectoral actions, identifying and controlling risks, identifying and implementing sustainable development actions, negotiating between stake-holders, improving mine production, etc. To respond to this need, the SIGAfrique Network proposed to develop a joint decision support tool entitled the African Mining Observatory (AMO) and, to this end, develops a system of indicators to be integrated within the SIGAfrique database. The development of both the OMA and the indicators is based on a participatory method within the working groups, which comprise experts/participants from the 13 SIGAfrique partner and observer countries (Guinea, Burkina Faso, Mali, Tanzania, Niger, Mozambique, Kenya, Uganda, Senegal, Angola, Madagascar, Ethiopia, and Mauritania).

Jan 1, 2007

By Robert C. White, Kurt W. Keskimaki

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Diesel equipment is employed for all development work, as well as production ore handling. Due to fluctuating demand for molybdenum, production rates have varied from 16,000 to 32,000 metric tons per day (18,000 to 36,000 short tons per day) over the last four years. In order to obtain the maximum air flow for minimum power cost the Henderson mine has completed the following modifications to the ventilation system: removal of large intake fans, elimination of underground booster fans, shutdown of tunnel exhaust fans, completion of the number 5 exhaust ventilation shaft, and use of partially debladed main exhaust fans. These changes have reduced the annual cost of mine ventilation at the Henderson Mine by over 80 per cent, a very critical cost savings in today&apos;s competitive molybdenum marketplace.

Jan 1, 1989

By E. Valdiviezo, J. F. Oliveira

Adsorption of residual flotation reagents onto equilibrium fluid cracking catalysts is a promising method of purification of flotation process water. In the present paper, adsorption of sodium dodecyl sulphate (SDS), dodecyl ammonium chloride (DAC) and sodium oleate onto a spent catalyst from petroleum industry was studied by analysing the residual concentration of the surfactant after contact with the zeolite catalyst. The adsorption of the DAC was rather low but SDS and sodium oleate presented a high affinity for the catalyst surface. The loading capacity was 4.2 kg/ton for SDS and 5.5 kg/ton for oleic acid. After the treatment of the loaded catalyst with a HCI 1 N solution these surfactants are desorbed and the catalyst may thus be regenerated. This would be an additional advantage to its low cost, not to mention its condition as a discarded product and its availability in large tonnages.

Jan 1, 1995

By Mario E. Rossi

The concept of entropy is classical in thermodynamics and information theory. Its potential use as a measure of the ordering of a spatial system is discussed. Although entropy has been discussed previously in the framework of spatial statistics and for univariate distributions, a bivariate data-based estimator has not until now been defined. Different statistical distributions maximize entropy, depending on the univariate, bivariate, or n-variate constraints applied. For bivariate distributions, with a known mean and known covariance, it can be shown that the distribution that maximizes the entropy of the system is the bivariate gaussian. A nonparametric bivariate entropy estimator is introduced, derived directly from the experimental cumulative frequency distribution. Assuming that this experimental bivariate distribution is representative of the population distribution, then a measure of departure from gaussianity can be introduced as a relative entropy estimator. Practical applications for the entropy estimator are discussed, and an example developed.

Jan 1, 1992

By George L. Baloo, Dave Kwiatkowski, Jose G. Cañlzales

Capital project funding for a medium to large materials handling project often includes a budget for procurement of supplier-recommended spare parts, and it is the Project Team&apos;s responsibility to select these parts. With today&apos;s economic climate, limited budget, and other factors, the spare parts selection process is a difficult and arduous effort. This decision carries with it a risk to plant operations and in some cases the commodities producers. Too often the decision-making process is not documented, and the reasons for eliminating and reducing quantities are based on "best guess " Recently on the Solids Handling Phase 2 Project in Jose, Venezuela, the Project Team took a unique approach to this problem. This paper discusses the analytical approach taken by the Project Team, the database system that was developed to manage this problem, lessons learned, and their applicability to pre- project planning and preliminary design.

Jan 1, 2004

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By Alan A. Campoli, Michael D. Zuber, Frank E. McCall, Gerald L. Finfinger

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1995

By G. L. Finfinger, F. E. McCall, A. A. Campoli, M. D. Zuber

Injecting pressurized water into a coalbed prior to mining reduces mining-generated respirable dust. Because of economic and geological barriers, water infusion for longwall dust control in the United States is now limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes that are drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob-gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob-gas boreholes. Computer coalbed-reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water-infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1997

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By E. Topuz, M. J. McPherson, J. Banik

This paper summarizes the analyses of ventilation layouts for mines that experience both spontaneous combustion. The major focus is placed on the longwall coal mine layouts used in several countries. Each of the different layouts is modeled in the form of a ventilation network. The gob of a longwall panel is the most critical location for the occurrence of spontaneous combustion. Airflow leakage paths inside the gob are simulated by using a simplified grid-like network. Computer simulations with this model indicates that the W-system of ventilation is most effective in minimizing air leakage into the gob. Homer, the U-system of ventilation, with pressure balancing behind the face support line, is also found promising for longwall panels. The magnitude of air leakage into the gob is observed to change with the advance or retreat of bee, thus requiring appropriate balancing of pressure to maintain the leakage at a minimum.

Jan 1, 1995

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By J. A. Herbst, Z. Rogovin, Lo. Y. C., K. Rajamani

Knowledge of the amount of time material spends in a continuous mill in a closed grinding circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of pulse tracers in residence time distribution (RTD) experiments. In typical grinding circuit experiments, RTD measurements are done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article, an easy mathematical method for calculating mean residence time and the degree of mixing of material in a mill present in a closed grinding circuit is developed. There are no restrictions on the location of the tracer injection or detection points with this method. Any convenient location in the circuit can be chosen without affecting the residence time distribution measured. The analysis of impulse response data obtained from several commercial grinding circuits using this method is presented.

Jan 1, 1988