Search Documents

By Edward Donovan, Bryan Knott, R. E. Melley, O&apos

South Bulga Colliery, located near Singleton in the Hunter Valley region of Australia, began longwall production in late 1994. The mining conditions there are conducive to high productivity with good roof conditions and a shallow seam with production areas located close to the portal. When the longwall was commissioned, the low capacity and availability of the conveyor system greatly curtailed the mine's productivity. A number of changes were made to the conveyor system culminating in a drive change out to improve the system. Using South Bulga as a case study, this paper aims to demonstrate the absolute necessity of a reliable, high performance conveyor system for the viability of a mine, and some of the factors that are needed to ensure a conveyor system performs as intended. These factors include a thorough understanding of the individual components and how they influence and interact with each other; a system design that is tolerant of variations in component performance and the necessity of robust and reliable communications and PLC programming.

Jan 1, 1996

By M. G. Bakker, D. D. Murphy, D. R. Spears

The US Bureau of Mines studied the mechanism of shear flocculation of silica with stearic acid. At pH 6 and 12, shear flocculation of silica was not observed with the addition of up to 4.5 x 10-4 M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations = 10-4 M (22.5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labeled with a doxyl group. The presence of the spin-labeling group did not greatly affect the shear flocculation properties of stearic acid. Adsorption of labeled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicated that the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-5 M (22.5 lb/st). The results are discussed in terms of a possible mechanism for shear flocculation.

Jan 1, 1995

More than 5,300 mining professionals from around the world attended the SME Annual Meeting and Exhibit, March 1-3 in Denver, CO. Seventy three technical sessions highlighted innovative technologies and applications for the development of mineral resources. And the exhibit featured 421 companies worldwide and 632 exhibit booths. The 1999 SME Annual Meeting had 10% international attendance Professionals from outside the United States were guests at the first SME International Reception. Other meeting highlights included the Keynote Session. This pivotal session examined the international experience of North American-based companies. Speakers presented their perspectives on international explorations and operations. Keynote speakers included Robert Buchan, Chairman an( Chief Executive Officer, Kinross Gold; Dave Baker, Director Global Mining Project Management, Caterpillar; and Leendert Krol, Vice President International Operations Newmont Gold. Ihor Kunasz, 1998 SME President, made the introductory remarks.

Jan 1, 1999

By Takahide Wakamatsu

In Japan all the complex sulfide ore deposits of base metals have been developed as underground mining. The underground mining cost is extremely high as compared with open pit mining case. Therefore, in milling section of base metal mines, technical advance for maximum recoveries of valuable constitutents in ore has been required all the time to utilize as much ore mined as possible. At present, in mill plants treating "Kuroko", complex sulfide ore, concentrates of copper, lead, zinc, pyrite and barite are produced, with gold and silver contents in the copper, lead, and zinc concentrates being estimated as extra profit. As in the case of Kuroko milling plants, gold and silver contents in the lead and zinc concentrates of lead-zinc ore milling plants are also varuable from an economical viewpoint. Silver content is very high in Kuroko crude ore as well as lead-zinc ore.

Jan 1, 1982

By J. Pflieger

The International Iron and Steel Institute (IISI - http://www.worldsteel.org) has initiated the development of a comprehensive freely-available, internet-delivered package of highly interactive e-learning resources for undergraduate students and steel industry employees. The resulting e-learning environment (http://www.steeluniversity.org) creates a ?one-stop? shop covering all aspects of steelmaking, steel products and applications, the underlying scientific and engineering principles, industrial and academic collaboration, as well as environmental and sustainability issues relevant to the steel industry. The module entitled ?Sustainability, Steel and the Environment? of the steeluniversity.org provides interactive e-learning resources on the following topics - Sustainability. - Principles of Life Cycle Thinking. - Environmental Life Cycle Assessment. - Application of Life Cycle Assessment. The aim of this particular module is to enable the learner to identify relevant environmental parameters over the life cycle of steel products as well as to learn about the resulting environmental effects and impacts. Furthermore he/she will be enabled to explain the basic idea of Life Cycle Thinking and Life Cycle Assessment (LCA) in terms of Goal and Scope definition, System Modelling, Life Cycle Inventory (LCI), Life Cycle Impact Assessment (LCIA) and Interpretation. In addition, the learner can explore selected LCA scenarios facing the steel industry and its customers in the automotive and construction sectors.

Jan 1, 2007

By Mark G. Aylmore, Eric J. Grimsey

Anenopyrite, both pure and in some cases associated with pyrite, was laboratory roasted either isothermally or at a constant heating rate, at temperatures mainly between 723 and 923 K and under environments of air, sulfur dioxide, oxygen and argon, as well as S02/02/H20/N2 mixtures. The mineralogy, arsenic contents and in some cases surface areas of the calcines were evaluated so as to provide an enhanced understanding particularly of the conditions under which the important transformations to pyrrhotite and magnetite occur. A thermodynamic analysis is also undertaken to rationalize the observations and provide some guidance for the operation of commercial roasters.

Jan 1, 1990

By Bernie W. Martin

The East Side Access (ESA) project is the largest commuter railroad project ever undertaken in the United States. The purpose of the ESA project is to bring commuters from Long Island into Grand Central Terminal. The program is estimated to cost $4.3billion. The purpose of this paper is to describe the key design elements for the Queens segment, ?re life safety, ventilation and changes to the proposed contract delivery method.

Jan 1, 2003

By Jerry Motz, Gary Beerkircher

Through a joint development program between Bougainville Copper Ltd. and Nordberg, the MP1000 cone crusher was developed and tested during the period between 1982 and 1987. Following the successful prototype work, Bougainville Copper purchased an additional three units. A second prototype was installed at Codelco's El Teniente three-stage crushing installation in 1987. This unit has also completed its test period successfully. Three additional units have been sold, making a total of eight, to date. Two will be installed as secondary crushers in two separate large aggregate plants. The first unit installed in the United States was placed in operation at Vulcan Materials Company's plant in Manassas, Virginia in early May 1990. Another unit is being installed in Asarco's Ray Mines expansion. The Asarco installation will be a SAG MILL pebble crusher producing approximately 600 STPH of nominal 1/2" product. Application Objective The objective was to design a crusher that would fit on an existing 7' foundation with minimum modification and yet be capable of twice the production of a 7' cone crusher. In meeting this objective, the power rating was increased to 1000 HP, the maximum design crushing force was increased and the crusher was designed to operate at higher speeds than an equivalent size Symons cone crusher. The MP1000 was also designed to operate with a head throw that can be greater than the equivalent Symons design. Design The crusher design criteria involved the recognition of the crushing force increase required for the finer crushed products than

Jan 1, 1992

By Randhir Sehgal

Heavy media processes have been used for cleaning +28 mesh coals for a number of years, Two applications, i.e., the vessels and the cyclones are widely used in the U. S. for this purpose. The basic reason for the popularity of these systems is their extremely high efficiencies for particle sizes above 28 mesh, However, application of heavy media technology to fine coals below 28 mesh, has been limited due to the following reasons: o Inability to make size separations effectively at sizes below 28 mesh o Necessity of feeding large quantitites of magnetite to the separators o Difficulty of recovering magnetite in the presence of large quantities of coal o High levels of coal contamination in the recovered media, leading to high circulating loads and ineffective control of media gravity

Jan 1, 1981

By P. T. Luckie

The selectivity curve -- a continuous function which predicts the expected proportion of feed material of a particular size that will appear as coarse material -- is the preferred model for describing classification. In a previous paper (I), the authors presented a technique for determining the selectivity curve of a classifier from experimental data. The separation process is defined by a binomial distribution of the form [ ] where s(x), the probability of particles of size x reporting to the coarse stream, is obviously the selectivity value for material of size x.

Jan 1, 1975

By Douglas M. Deason

Swelling clays, such as montmorillonite, contribute significantly to the poor dewatering and consolidation behavior of the Florida phosphate clay wastes. Understanding and to a degree, control of the forces which cause the swelling behavior may aid in supplying a solution to this problem. The technical feasibility of utilizing control- led dispersion for aiding dewatering of phosphatic slimes was investigated. This technique is based upon inhibition of swelling and self-dispersing tendencies of the montmorillonite clays by dispersing the solids in electrolyte solutions. Through this process, significant improvements in settling rates and sediment solids content were achieved in both pure clay systems and on simulated phosphate slimes.

Jan 1, 1983

By Tsutomu Yanagase

Non-ferrous smelting industry in Japan often had the severe problems about the over production of sulfuric acid. There has been such a closed relation between amount of sulfuric acid from non-ferrous smelting industry and the products of copper, zinc and lead metals that the production of one ton of copper accompanies three tons of H2S04. When the proper balance exists in both markets this situation certainly brings bigger profits. In Xining and Metallurgical Institute of Japan the research commitee concerned with the fixation process of sulfur in non-ferrous smelting industry was established in 1977 and continued the activity for four years untill 1981. This paper will introduce some of the activities involved in the report published by the committee.

Jan 1, 1982

By H. Walqui, A. Buendía

The Toquepala concentrator expansion project incremented the capacity of the existing concentrator by 15,000 Metric tons per day (t/d), from 45,000 to 60,000 t/d. The plant is located in southern Peru,1,200 km southeast of Lima. The implementation plan for the expansion project was based upon an engineering and procurement contract, and a construction contract. The overall Project Management was by Southern Peru Copper Corporation (SPCC). The expansion followed a very aggressive schedule that considered a construction period of only ten months, with minimum interference to the existing facilities. Major equipment was purchased during basic engineering. This paper details the design, construction, and commissioning of the 6.4 m diameter by 10.2 m long ball mill, and the performance of the milling circuit during the first two months of operation.

Jan 1, 2003

By Cong Zhang, Huaying Wang, Yixin Wei

"Water inrush is a serious geological accident in underground coal mines. This paper focuses on the method of the bow tie analysis based on fuzzy reliability to assess the risk of water inrush in coal mines. First, post failure probability and repair probability of initiating events are divided into 5 levels. Then triangular fuzzy numbers are adopted to quantify experts’ language and to acquire the reliability rate which close to the actual values by defuzzification and calculation. According to dynamic bow-tie analysis model, using the method of moments to fit the reliability time of events by Weibull distribution and offering the random sampling rule of failure and repair time for illustrating the feasibility of fuzzy reliability evaluation. To demonstrate the effectiveness of the proposed assessment approach, bow tie analysis model of water inrush in coal mines is taken as an example.Introduction Dynamic bow tie (DBT) analysis is composed of dynamic fault tree and dynamic event tree analysis, and considers the impact of the time factor upon risk assessment of a system. There are many algorithms applied to calculation of the probabilities of node accident and accident consequence of dynamic bow tie analysis: Hidden Markov Model, Bayesian Network (Khakzad et al 2013), Integral Algorithm (Amari et al 2003) and Monte Carlo Simulation (Kim et al 2016). In terms of simulated time and practicability, the Monte Carlo Simulation has an advantage over other methods. DBT requires mass data in quantitative analysis, including the failure rates and the repair rates of the basic events of the Fault Tree (FT) and the subsequent events of the Event Tree (ET) at different time points, i.e., the distribution of failure time and repair time. In practical analysis, it is hard to obtain a large amount of exact historical statistical data, which is a major problem of risk assessment. Due to the difficulty of obtaining the exact data and historical failure data of the basic events and the subsequent events, the FT and ET analysis is stuck with the study of minimal cut sets, minimal diameter sets, structural importance and qualitative analysis (Liu and Zhang 2010, Yan et al 2012, Wang et al 2009, Li and Wang 2011). This paper will use fuzzy numbers and the defuzzification method to transform the experts’ language into the failure rates and repair rates of basic events and subsequent events, solving the problem that it is difficult to obtain a large amount of historical statistical data, and will use the method of moment to conduct Weibull fitting of the reliability time to provide the random sampling criteria of event failure and repair time in Monte Carlo simulation."

Jan 1, 2017

By Robert W. Cope

"Mining began, in the Colstrip area in the 1920's by the Northern Pacific Railroad. The coal was used for steam locomotives until 1957, when the advent of diesel power made them obsolete. In 1959, Montana Power Company purchased the Northern Pacific properties including the mining equipment, coal leases and the town of Colstrip. Western Energy Company, a wholly owned subsidiary of Montana Power Company was formed in 1966 to manage the mining operations in Colstrip. The Rosebud Mine officially re-opened in 1968 to supply coal for Montana Power Company's J. E. Corette Plant In Billings. Since 1970, Long Construction has operated the mine equipment for Western Energy Company". The Rosebud Mine is located in Southeast Montana and supplies coal to two 350 megawatt power plants located in Colstrip and one 180 megawatt plant located in Billings. Approximately 30 percent of Western's annual production is consumed by these plants. The remaining production is shipped to the mid-west and burned by utility companies and municipalities.

Jan 1, 1981

By Songlin Ye, Frank Su

"Recycling valuable metals from waste streams has become increasingly important to the mining and smelting industry in China due to resource depletion and environmental concerns. Predicated on multiple large scale metal recovery operations designed by BQE Water at active mines in the Jiangxi Province of China, this paper presents a case study demonstrating recovery of zinc and copper from the waste stream at a major gold smelter in the Shandong Province of China. One of the issues facing the smelter is the lack of a cost-effective and robust process to recover zinc from the acidic process waste stream. As such, significant amounts of zinc-containing wastewater are neutralized with lime, resulting in not only the loss of zinc metal but also the generation of large volumes of sludge. In the case study, a sulphide precipitation process is chosen to selectively recover zinc and copper from the wastewater, in the form of commercial grade metal concentrates that can be sold as regular concentrates at the going market price. In the current project phase, over 2,500 tonnes of zinc metal and 40 tonnes of copper metal can be recovered on an annual basis. This not only generates revenue to offset waste treatment costs, but also eliminates significant amounts of sludge that would otherwise require storing and further disposal if the metals are not recovered.Introduction / Background With resource depletion becoming a global concern and environmental regulations becoming increasingly strict, companies in the mining and smelting industry are actively seeking technologies to maximize resource recovery and provide concurrent minimization of waste residue production from operational activities. Mining and smelting companies have typically used lime neutralization as the primary method to reduce metal concentrations from mine waters prior to reuse or discharge to the environment. However, this process creates large volumes of metal laden sludge with long-term liabilities in the form of ongoing storage and management (Zinck et al 1997). Recovering metals of value from mine water not only reduces sludge volumes and the costs of associated liabilities, it produces a commercial grade metal concentrate that can be sold to generate revenues to offset treatment costs. ChemSulphide® is a sulphide precipitation process developed by BQE Water that has been successfully applied at mine sites in the Jiangxi Province of China to remove and recover copper from acid mine drainage. The success of these copper recovery water treatment plants demonstrates both the economic and environmental benefits of recovering residual metals from mine water and provides reference for the copper and zinc recovery project at a gold smelter in the Shandong Province that is the subject of this case study."

Jan 1, 2017

By Jürgen Brune, Purushotham Tukkaraja

This editorial introduces a special focus issue on mine ventilation innovations. It highlights key areas such as ventilation on demand, automation, thermal management, atmospheric monitoring systems, and prevention of mine fires and explosions. The issue aims to address the critical role of mine ventilation in maintaining the health and safety of miners.

Mar 21, 2022

By S. McMurray

INTRODUCTION Towards the end of the 1890s the attention of a prospector by the name of Thomas Cullinan was drawn to the occurrence of alluvial diamonds east of Pretoria. Persistent prospecting work by Cullinan led to the loca¬tion of the source of these diamonds-a kimberlite pipe on the Elandsfontein farm. Cullinan eventually acquired the property in 1902, and during an extensive evaluation program outlined the largest diamondiferous pipe in South Africa on which the Premier mine was established. Worldwide attention was drawn to this mine in 1905 when the Cullinan diamond, which weighed 3106 carats and is by far the largest gem diamond ever discovered, was recovered. Premier mine operated with varying success until 1932 when the worldwide depression forced it to close. In 1945 the mine was reopened and since then has been a major producer of gem and industrial diamonds. During the early 1950s exploratory drilling revealed that below the 370-m level the pipe had been completely cut off by a younger gabbro sill. This sill has created major mining and metallurgical problems but the existence of vast reserves of high grade ore below it justi¬fied the establishment of virtually a new mine below the sill. Detailed planning of below-the-sill mining is nearing completion and the development of the first mining block (the L1 block) is well advanced. A full discus¬sion of this block follows. GEOLOGY OF PREMIER MINE Pipe Morphology and Country-Rock Geology As can be seen in Fig. 1, Premier mine is an elon¬gated oval shape with a long axis of 900 m on the surface and a short axis of 450 m. The pipe has a surface area of 32 hectares which decreases progres¬sively with increasing depth, so that 500 m below the surface the area is reduced to 22 hectares. The contact between the kimberlite and the surrounding country rock is sharp, with an average angle of dip of 1.48 rad (85°). From the surface down to approximately 350 m, the country rock is a felsite which grades downwards into a norite. In general both rock types are hard and massive, the felsite in particular being poorly jointed. This characteristic combined with other factors results in an extremely stable open pit, and near-vertical side¬walls are currently being maintained. The norite in general is competent but is heavily jointed in some areas resulting in very blocky ground which creates localized tunnel support problems. In the southeastern area below the sill a zone of highly altered and very unstable norite, which has also created localized sup¬port and development difficulties, lies adjacent to the pipe contact. Kimberlite Geology The Premier pipe is a complex multiple intrusion which contains in the region of 15 separate types of kimberlite, most of which are volumetrically insignifi¬cant. On a simplified basis three major types can be identified which correspond to three separate phases of intrusion. They are: Brown Kimberlite: This represents the first phase of intrusion and now occupies the eastern part of the pipe. In plan the brown kimberlite has a crescentric shape resulting from the intrusive relationship with the younger gray kimberlite which lies to the west. The brown kimberlite increases in relative area with increas¬ing depth which is a favorable factor for future mining operations since this kimberlite is the richest area of the mine, having an average grade of 70 carats/ 100 t. Below the sill this rock disintegrates extremely rapidly when exposed to air or water, to form a fine gravel-like material. This characteristic is due to a high montmorilonite clay content. As is common with clay minerals of this type, water can be absorbed into the crystal lattice with a resultant increase in volume which causes the physical decomposition of the rock. The presence of this decomposing kimberlite was a major factor governing the choice of a mining method, as well as development and tunnel support techniques. Gray Kimberlite: This is the most abundant type and represents the second major phase of intrusion. The diamond content is variable depending on the amount of waste rock dilution, and in general the rock is stable and non-decomposing. At the time of formation of Premier, the surface rock type was Waterberg quartzite, a rock formation which has subsequently been removed from this area by erosion. The explosive extrusion of the gray kimberlite caused extensive brecciation of this rock and while the kimberlite was in a mobile state huge masses of quartz¬ite, amounting to tens of millions of tons, slumped into the pipe. This quartzite became concentrated in the central area of the mine and has been a major mining problem throughout the history of Premier since, due to the irregular distribution of the quartzite, effective selective mining has never been possible. The quartzite is therefore extracted with the ore and has a significant dilution effect on the overall grade. Black Kimberlite: In the western part of the pipe a circular, pluglike body of kimberlite is intruded into the gray kimberlite. This plug consists mainly of a hard, dark-colored rock known as black kimberlite, but also contains a number of minor kimberlite variet.ies as well as nonkimberlite carbonate dikes. The Gabbro Sill The sill averages 75 m in thickness and within the confines of the pipe consists of 52 million t of rock. On average the major dip is 0.34 rad (20°) to the northeast which is across the short axis of the pipe, the range of dip being from near horizontal up to 0.52 rad (30°). Due to the pronounced dip, the sill is encount¬ered over a vertical distance of 175 m with the highest upper contacts on the 355-m horizon and the lowest bottom contact on the 530-m horizon.

Jan 1, 1982

By R. Froidevaux

Geostatistical estimation techniques were customized to enable forecast of production figures at the Silver Bell uranium mine (Uravan District). Surface drill hole data were used to provide a block model of kriged estimators of average uranium grades. The recoverable figures, such as ore-waste ratio and ore grade, are then deduced from regressive curves previously obtained from underground information and production data. Cross-validations of the entire model were performed and were found positive.

Jan 1, 1981

By G. W. Cutting

It is well known in both the research field and in commercial flotation processes that the grades and recoveries obtained from flotation plants are heavily influenced by the structure and height of the froths produced in the flotation cells. The development of steady-state mathematical models of flotation processes based upon practical and readily obtained parameters have demanded detailed information about the structure of flotation froths. The important parameters are the distribution of floating values, gangue and water in the froth with respect to froth height, cell pulp density, cell air flow rates and flotation inducing additives. Little work has been conducted in this field although considerable attention has been paid to bubble loading and other factors close to the cell froth/pulp interface. Laboratory batch tests are prefaced for the derivation of the above mentioned parameters for both practical and economic reasons. The standard laboratory flotation tests using a batch cell produces a froth of low height (1 to 3 cms generally) together with a varying cell pulp density as the test progresses due to the addition of top up water and the removal of froth from the cell. This form of test can be considered only as giving information about froth conditions close to the cell froth/pulp interface under conditions of widely varying cell pulp densities. In commercial processes the froth heights are much larger (frequently greater than 10 cms); therefore the laboratory batch test, although useful in many ways, does not directly yield parameters relating the state of the froth flowing over the cell lip to process operating conditions. To investigate flotation conditions, where more realistic froth heights are developed, an equilibrium type of batch cell has been developed at Warren Spring 1 Laboratory . In this a tank with high walls is used to contain the pulp and whole froth and, after a short period of operation, an equilibrium between froth

Jan 1, 1975