Search Documents

By George F. McIntyre

The subject of this paper is mineral processing chemicals - how they work and where they end up environmentally. First of all, it is necessary to recognize that water is the most universally and widely used chemical used by the mining industry to separate desirable minerals from unwanted wastes, sands, and slimes. Of the total world's water supply, over 97 percent is found in the oceans. Another two percent is tied up in the ice caps, leaving roughly only one percent for us to work with. This one percent is distributed either as ground or surface water and makes up the bulk of all water used industrially. Even with such a small proportion available for immediate use, there appears to be enough fresh water to meet our needs for at least another hundred years. This availability, however, depends heavily on how we handle our waste waters, how we process them, and how we plan for their reuse. Certain governmental agencies have been charged with the task of setting up standards of water quality which must be met prior to environmental discharge. There is even discussion of zero discharge from industrial operations. Due to limited supply and availability, the mining industry has always been forced to reuse its process water or to treat it prior to discharge. Consequently, we are in an enviable position and are presently able to live with the environmentalists demands. To stay on top of the situation, it is necessary to continually concern ourselves with the .effects of changing orebodies and reagents on the final mill effluent. From a process standpoint, it is also important to recognize the impurities of plant recycle water and how they might tend to influence overall operations

Jan 1, 1974

By P. Oghazi

It is possible to have traceability in the mining industry, by parameters and signatures like particle mineralogy, mineral association, texture and mineral liberation. The study is on an apatite-iron ore deposit at Malmberget, Sweden, and characterizes an ore body both mineralogically and texturally in a quantitative manner by using analytical methods like optical microscopy, microprobe (EMPA) and an automatic SEM based system, Particle Texture Analysis (PTA). The mineralogy was evaluated by PTA and characterized by modal mineralogy, mineral liberation and mineral associations. Magnetite has a simple outline and straight grain boundaries and the gangue minerals have a finer particle size with a more complicated texture. The PTA analysis also shows that apatite is associated to magnetite as mixed particles, while smaller grains of magnetite are inclusions in feldspar. Result from particle texture analysis shows that there is a connection which link to the mine-to-mill context, and it may be used to create traceability. This link is not the associations of the main ore mineral magnetite, nor the modal mineralogy. Instead, it is the mineral associations of contaminating minerals (apatite and feldspar) that appear to be most promising since they survive from mine to mill. The modal mineralogy may be used to understand how contaminated minerals break into or out of particles size fraction during grinding.

Jan 1, 2010

By E. Watkins, S. J. Schatzel, K. Ajayi, V. Gangrade

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research related to unconventional gas wells positioned in abutment pillars associated with active longwall mining in Southwestern PA. The Ventilation and Explosion Prevention Team at NIOSH is working toward predicting and characterizing a hypothetical casing breach and its effect on the safety and health of mine workers, gas well workers, and the general public. An important aspect of this research is to distinguish coalbed gas from shale gas in the mine environment as an indicator of a casing breach. Another noncoal gas source exists in the region in the form of underground gas storage fields which also have the potential to migrate towards mine workings. During a potential gas breach, the addition of excess natural gas to coal mine environments will exceed the anticipated ventilation loading and can create a mine explosion hazard. A methodology has been developed to distinguish these gas sources. Gas samples from the three sources were analyzed by gas chromatography, and interpretive methods were applied to distinguish the populations graphically and statistically. Bivariate plots using the hydrocarbon index and the normalized molecular ratios showed that the sources occupy different regions of the graphs. All samples of non-coal gas contained under 2% CO2, and all coal samples included greater than this amount. A multivariate T-squared (T2) test analysis relating comparing data in pairs showed a low p-value (dimensionality parameter) and a high T2 test statistic for all comparisons, indicating that these sources are different and distinct gas populations. Ultimately, stakeholders from the mining and gas production industries can utilize this method to identify gas sources and a potential casing breach.

Mar 2, 2022

By Herb Wilson

The Klondike symbolized one of mankind's driving forces - the desire to lay one's hands on a scarce resource, gold, in that case - and in doing so to make some money along the way. It can be argued that construction aggregates - a once lowly and ignored sector of the natural resource industries - have become the desired targets of their own "Klondike." This began in the 1970s and accelerated to a frantic pace in the 1980s. The scope of industrial minerals is very wide. It ranges from high value minerals such as talc, bentonite and kaolinite to the truly humble minerals of sands and gravels, limestones and granites. Their major end uses are in construction aggregates. A rich variety of different mineral types all make good construction aggregates. However, those successfully used have two fundamentals in common: • Their technical characteristics are appropriate for the requirements of their end use. • They are located within an economic distance from the market. The North American market This is the largest construction ag¬gregate market in the world. Consumption in 1990 reached 2.2 Gt/a(2.5 billion stpy). This rate of consumption has grown steadily over the past decades. In the United States, from 1963 to 1989, it averaged a 1.6% compound growth rate. Within this long-term trend, there are business cycles, because aggregate demand is closely linked to economic strength or weakness. The North American market also displays the greatest per capita demand for aggregates when compared to the major industrial economies (Table 1).

Jan 1, 1993

By Yoginder P. Chugh

The term "fatigue" in mechanics, is used to refer to reduction in the strength of a material subjected to fluctuating or alternating stresses. Stresses that vary with time are called fluctuating stresses and if during fluctuation the stresses also change sign, they are called alternating stresses. In the field of rock mechanics, the term fatigue (static fatigue) has often been misused to refer to failure of geologic materials in time domain under constant load. To avoid confusion, we use the ten cyclic fatigue here to refer to failure of rock under alternating or fluctuating stresses. Fatigue in metals has been studied for over 100 years. Fatigue properties of geologic materials have, however, received little attention in the past. This is probably because until recently very little was known in regard to the behavior of geologic materials even under static loading. Secondly, suitable equipment for conducting cyclic fatigue experiments was not available until quite recently. A few cyclic fatigue studies have been undertaken on geologic materials to relate it to percussive or rotary drilling mechanisms (e. g. Grover et a11*; Burdine2). The results of these studies were inconclusive due to limited effort. Cyclic fatigue in concrete has been studied more extensively than geologic materials (e.g. Nordby3, Gray et al 4 and Bennett et a15) and mechanisms of fatigue in concrete are better understood than in geologic materials.

Jan 1, 1975

By Phillip J. Maddex

Transportation is a major part of yours in the industrial minerals industry. Whereas federal income taxes merely take 50 per cent of your firms profits, transportation cost may take 50 per cent of the gross realization - selling price plus transportation - on your product, f. o. b. customers plant.

Jan 1, 1969

By S. C. Libby

The amount of fine material (minus 60 Tyler mesh) generated during calcination and/or handling of calcined abrasive grade bauxite from Alcoa's operations at Moengo, Suriname, has recently increased relative to past production experience. Bulk samples of raw abrasive grade bauxite from three deposits in the Moengo area have been studied in order to determine the factors controlling the generation of fine material samples from the Jones IC and Tapira deposits, which generate excessive amounts of fine material, have been compared with reference samples from the Begi Gado deposit, which does not generate excessive fine material. Additional type samples of abrasive grade and marginal abrasive grade bauxite from deposits in the Moengo area which represent different bauxite textures found in the Jones IC, Jones I, and Begi Gado deposits have also been studied. Field observations in the Moengo area have indicated that abrasive grade bauxites with a dull, earthy appearance generally do not generate excessive fines. On the other hand, excessive fines are generally associated with coarsely crystalline bauxite in which the gibbsite crystals appear to sparkle in sunlight.

Jan 1, 1980

By J. K. Ross, K. O. Hoal, S. K. Appleby

Understanding ore variability is a key factor in the geometallurgical analysis of a deposit and is beneficial to process development and mine planning. Ore variability is a function of the mineralogy of a deposit, in terms of both ore and gangue minerals and their textural relationships. This study integrates optical microscopy and quantitative mineral analysis to characterize the mineralogy and texture from 13 samples from different lithologic units at the Bingham Canyon Mine. The analysis identified several parameters, such as modal mineralogy, alteration assemblages, distribution of mineral phases and alteration assemblages and microfracture and void space distribution. These parameters can have an impact on the materials’ behavior during processing. This study demonstrates that quantitative mineralogical analysis can provide detailed information for improved understanding of ore variability.

Jan 1, 2010

By D. A. Fenton

The reliability of large diameter, high horsepower ball mill is paramount when large production and minimum downtime is required. The 17 ft. x 56 ft. double compartment ball mill at St. Lawrence Cement Company has the first gearless drive built in North America and has the world's largest hydrodynamic bearings currently built and running. The machine has seen three years operation and has met its specifications. The mill was designed by Aerofall Mills Limited and the gearless drive built and designed by the Canadian General Electric Company. This paper discusses the operation of the first North American installation of a gearless drive ball mill from the mechanical, electrical and process aspects.

Jan 1, 1977

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By R. L. Shaw, D. W. Alexander

Consolidation Coal Company's Loveridge Mine operates the only coarse coal hoisting and overland slurry transport system in North America. The system has been in operation since April 1980 and according to current haulage levels will have handled over two million tons by this conference date. Original performance goals have been exceeded. The systems will be described and their application to rapid excavation and tunneling haulage needs will be discussed. Manuscript not received in time for publication.

Jan 1, 1983

Strainburst phenomena, generally characterized by a sudden release of energy in a volume of highly stressed rock, are often encountered in such situations like crown pillar bursts in cut-and-fill mining, face bursts at development headings and floor bursts in deep shaft sinking. This paper describes a simple FE modeling approach which leads to the calculation of the energy release rate (ERR) and the total energy storage rate (TESR) in the rock mass around the openings. The merits of using such energy parameters in the analysis of strainburst problems to identify areas of high energy release/storage are discussed. However, much site-specific back analyses are needed to better understand how strainbursts and energy parameters are inter-related.

Jan 1, 1998

By Adam Bezuijen, Tiago Gerheim Souza Dias

"The construction of mechanized tunnels in soft ground has evolved significantly over the last 20 years, especially in the control of the face pressure and the closure of the soil-lining void to reduce the induced settlements. On the other hand, several mechanisms of the TBM excavation cycle are still not taken into account for routine design calculations, such as the increment of water pressures in front of the tunnel face, the flow of excavation fluids around the shield, the dynamic equilibrium between the grout pressures and the excavation convergence, among others. This paper discusses specifically the issue of face pressures and how several mechanisms, which are routinely not considered, can be easily verified and incorporated into the state-of-practice of design. INTRODUCTION The stability of underground excavations is traditionally assessed through analytical solutions based on the lower bound theorem of plasticity (Atkinson and Potts 1977; Mühlhaus 1985) or the limit equilibrium method (Anagnostou and Kovári 1994; Messerli et al. 2010). These methodologies depend on the tunnel geometry, certain ground parameters and the support pressure. When conventional construction methods are used, the internal support pressure is an abstract representation of the combined effects of partial excavation, ground reinforcement, and the different support elements. The use of closed-face tunnel boring machines (TBM) changed this perspective, as the magnitude of pressures acting on the excavation boundary could be controlled in a more direct way. In front of the TBM the ground is excavated as the cutterhead rotates and the cutting tools scrape the ground from the tunnel face while additives are injected to condition the material. Water, polymers, bentonite, and foam can be used as additives under different conditions (Thewes et al. 2012). The loosened ground with additives, herein referred to as the mixture, flows through the openings at the cutterhead and into the excavation chamber. This mixture is kept pressurized to support the face."

Jan 1, 2016

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By A. J. S. Spearing, G. Bylapudi, K. Mondal

The mining industry is a major consumer of rock anchors in the United States. Due to the high humidity in the underground coal-mining environment, the rock anchors corrode and lose their load bearing capacity, which, in turn, reduces the life expectancy of the ground support. This creates operational difficulties and a number of safety concerns (Li and Linblad, 1999). Research on rock anchor corrosion has not been adequate in the past and the effects of several factors in the mine atmosphere and waters are not clearly understood. One of the probable reasons for this lack of research may be attributed to the time required for gathering meaningful data. Underground water samples from different mines in the Illinois coal basin were collected and the major chemical content was analyzed and used for laboratory testing. The corrosion performance of the different commercial rock anchors was investigated by techniques such as laboratory immersion tests in five different corrosion chambers and potentiodynamic polarization tests in simulated ground waters based on the Illinois coal basin. The tensile strengths were measured for the selected rock anchors taken every three months from the salt spray corrosion chambers maintained at different pH values and temperatures. The corrosion potential, corrosion current and the corresponding corrosion rates of the #5, #6, #6 epoxy-coated and #7 forged-head rebar steels, #6 and #7 threaded-head rebar steels were measured in the pHs of 5 and 8 at room temperature. The open circuit potential (OCP) readings of the different rock anchors were recorded in three selected underground coal mines (A, B & C) in the Illinois coal basin and the data compared with the laboratory electrochemical tests for analyzing the life of the rock anchors installed in the mines with respect to corrosion current measured.

Jan 1, 2010

By William Lyman

GENERAL DESCRIPTION Shrinkage or shrinkage stoping refers to any mining method in which broken ore is temporarily retained in the stope to provide a working platform and/or to offer temporary support to the stope walls during active mining. Since ore "swells" when broken, it is necessary to shrink the muck pile a corresponding amount by draw¬ing some of the broken ore out as the stope is advanced-hence the name. Broken ore retained during stoping is drawn out after the stope has reached its limits. The stope may be left empty or may be filled with waste contemporaneous with, or subsequent to, the final draw. Traditionally the method implies conventional overhand stoping methods with miners working between the muck pile and the stope back, in a space which advances updip with mining and is maintained by balanc¬ing "swell" with "shrink." The shrinkage classification is also applicable to so-called "semishrinkage" methods in open pillar-supported stopes where broken ore is temporarily retained as a working platform but offers no wall support; and to various blasthole shrinkage methods which utilize broken ore temporarily retained in the stope for wall support, but which do not require miners to work from muck pile in the stope. The method is generally applied to steeply dipping veins of strong ore between strong walls. APPLICATION Geometry The geometry of a shrinkable vein is described in terms of dip, width, and regularity along dip. Overall strike and dip dimensions and irregularities along the strike generally impose no restrictions on the method. Dip is ideally 1.2 to 1.5 rad (70 to 90°). As dip falls below 1.2 rad (70°), the shrinkage draw begins to strongly favor the hanging wall side, thus leaving a poor working platform for conventional overhand work. This is particularly true in relatively wide stopes. The sup¬port afforded to the hanging wall also diminishes with decreasing dip, reaching nil as the dip approaches the repose angle of broken ore. Dips below 0.78 to 0.87 rad (45 to 50°) are not generally shrinkable except by open stope "seinishrinkage" methods. Minimum mining width is fixed by working space requirements in the stope-generally about 1 m. Shrink¬age in narrower veins requires that waste rock from one or both walls be broken with the ore and the attendant dilution accepted to achieve the minimum width. Nar¬row stopes are less suitable, encouraging hang-ups and bridging of broken ore, with the attendant problems of erratic draw and incomplete recovery of broken ore. Maximum practical width may be 3 m or less to over 30 m, depending upon the competency of the ore and its ability to stand unsupported across the stope back. This is a vital safety consideration in conventional over¬hand stopes, but is much less of a factor in blasthole shrinkage methods. Very wide veins and massive ore bodies have been mined by transverse vertical shrinkage panels separated by transverse vertical pillars which are either abandoned or recovered later by other methods. Regularity along the dip is a prerequisite of shrink¬age as there must be no serious obstruction to the flow of broken ore downward through the stope to the sill level. Gentle rolls along the dip are acceptable if the local footwall dip everywhere exceeds 0.78 to 0.87 rad (45 to 50°). Off-dip hanging wall and/or footwall splits can generally be mined selectively from a conventional shrink stope as they are encountered without ad¬versely affecting subsequent continuation of shrinkage mining updip on the main vein. Vertical offsets or major rolls along the dip which cannot be "smoothed over" generally require that a sublevel be established with new draw control development. Blasthole shrinkage methods are much less flexible (and thus less selective) in their ability to accommodate any of these irregularities. Ground Conditions The wall rock must be strong enough to stand with the minimal support afforded by the dynamic mass of broken ore in the stope. During active mining, local sloughing from the walls is restrained, but the broken ore affords little, if any, useful resistance to closure of the stope walls. Such squeezing, if present, may bind up the stope and cause the loss of much ore. Pillars left between and/or within stopes are effective in preventing closure but reduce overall recovery. Walls may be re¬inforced by bolting after each stope cut in conventional shrinkage but not in blasthole shrinkage. Ore in place must be strong enough to stand with no natural support across the stope width, although tem¬porary artificial support or reinforcement may be used locally in conventional stopes. Some spalling or sloughing is permissible in blasthole shrinkage as men are never present in the stope. Physical and/or mineralogical characteristics of the broken ore may impose restrictions on stope design and/or operational plan¬ning, and may even preclude the use of shrinkage al¬together. Examples include: ores which, when broken, are cohesive or which tend to pack or cement together under the influence of ground water, wall pressure, and/ or chemical reaction. Such conditions precipitate er¬ratic draw during mining and often result in difficult and/or incomplete final draw; pyritic ores which oxidize very rapidly in the stopes and may generate heat, imposing a fire hazard by spontaneous combustion; sulfide ores which oxidize sufficiently in the stopes to adversely affect mill recovery by flotation; and ores (es¬pecially those containing uranium minerals) which ex¬ude radon gas and thereby impose ventilation constraints on stope design. In most cases these problems can be minimized by limiting the size of stopes, by minimizing the duration of mining activity in each stope, and by promptly drawing each stope empty following comple¬tion of mining.

Jan 1, 1982

By Alejandro Prieto

Traditionally, Mexico has been a mining country. This industry has played a very important role in our country's development, creating jobs, integrating geographical regions - generally very remote from urban communities - and, an essential factor in our present day economy, generating an influx of foreign currency. The Fluorspar mining industry's development started in the 1920?s, but it was not until World War II that its exploitation became consistent and started growing. During the last few years, Mexico has become the world's leading producer, with an annual output of more than one million tons, which directly generates over 3,000 jobs. The actual proven reserves can guarantee fifty years of production at this same annual rate, and it is due to this fact that the producers have not increased their reserves. However, there is concrete information of the existence of several deposits, extending from the northern border to the gulf of Mexico, forming the "Fluorspar Belt? in Mexico.

Jan 1, 1986

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By Danforth R. Hale

The pressure of military use of quartz resonators led to efforts to Grow high, grade quartz crystals in Germany and in Great Britain during 19)3-25, and was responsible for a series of U.S.A. Signal Corps contracts beginning in 1946 with the Clevite Corporation (as the former Brush Development Company), Bell Telephone Laboratories, Antich College, and others. The technique of growing crystals from the melt, such as KI, NaBr, was already commercially inuse Quartz could not be so grown, since its utility depends on the form stable below 573°C, and, even if it could be grown from an extraordinarily viscous melt, the higher form passing through this transition becomes twinned. Again, several crystals were being grown commercially from water solutions; quartz, however, is listed in the common literature as being insoluble in water. Fused quartz, or vitreous silica, was chosen as raw mater¬ial by the European experimenters because of its thermodynamically lesser stability than quartz, and various alkaline solutions were tried for the purpose of enhancing the solubility.

Jan 1, 1964