Search Documents

By B. D. Paphane

Since the commissioning of the Tati Hydrometallurgical Demonstration Plant (HDP), which produces Ni and Cu cathodes as well as Co salt from sulphide concentrate employing Activox® technology for leaching, no kinetic data has been generated from the plant under normal operating conditions, from start-up to steady state. Therefore, this study seeks to determine the rate of reactions in the leaching circuit with a view to obtaining kinetic data for the system under the current operating conditions. Within the five-compartment autoclave operating at temperatures of 105°C to 110°C and 1100 kPa pressure, the extraction of Ni, Cu, and Co ions into solution is achieved through the oxidation of the sulphide concentrate using approximately 50 kg H2SO4 per ton, 10 kg NaCl per ton, and 1.21 kg O2 per kilogram of S2-. The autoclave reactions showed complex kinetics, with the reactions proceeding via some intermediate(s) before the formation of products. The results suggest that the reactions were dependent on the size of the metal ion of interest and the concentrations of the metal ions in the Tati concentrate as well as in chloride leaching. The order of the leaching rate constants was Fe2+ > Cu2+ > Ni2+ > Co2+ in all the compartments studied. The rates of leaching were also found to decrease as the concentrate moves from compartment 1 to compartment 4. For compartments 1 to 3, leaching was observed to be preceded by dilution of the repulp liquor (copper raffinate). The leaching rate for compartment 5 was slightly lower than that of compartment 1 but higher than the rates of compartments 2, 3, and 4 for all the metals studied. Keywords kinetics, hydrometallurgical plant, Activox

Jun 1, 2013

By M. Berger

The ‘Metallurgical Operations’ Department of Grinaker-LTA Process Engineering (GLTA) currently undertakes then primary mining as well as the re-deposition of tailings forTicor South Africa (Ticor) at their Hillendale mine near Empangeni, KwaZulu-Natal, South Africa. The mining plant, which was designed by GLTA on a Build, Own, Operate and Transfer (BOOT) basis, is capable of mining 780 000 tons per month of ROM material which is then pumped to the Primary Wet Plant for treatment by Ticor. Hydraulic mining via high pressure water cannons and subsequent transfer of the heavy mineral slurry at an RD of between 1.35 and 1.48, has never before been undertaken successfully at this level of production on an in situ reserve. The presentation will take the form of a case study in which the unique site operating conditions will be detailed and discussed, as will the innovative process and engineering solutions employed by GLTA to overcome the engineering and production challenges encountered. In order to protect the intellectual property involved in this operation, this paper is fairly general in nature, and attempts merely to provide the reader with a broad perspective understanding of the operation, and some of the difficulties encountered during the early stages of production.

Jan 1, 2003

By A. F. van der Merwe, R-D. Taylor, M. Jacobs, F. H. Conradie

Total bound moisture (TBM) is a typical quality indicator of industrial-grade gypsum. This gypsum is comprised of three distinct phases, namely anhydrite, dihydrate, and hemihydrate, of which only the latter is of much industrial use. TBM analysis is a lengthy laboratory procedure, and an artificial neural network (ANN) TBM inference measurement is proposed as a fast and online alternative. An ANN inference model for gypsum TBM based on plant data was developed. The inputs to the network were primarily focused on the plant's calciner, and different network topologies, data divisions, and transfer functions were investigated. Furthermore, the applicability of the TBM value as a quality indicator was investigated based on a gypsum phase analysis. A strong correlation between TBM and the gypsum hemihydrate and anhydrite content was found, validating the plant target TBM of 5.8% as a quality indicator. A network topology consisting of one hidden layer with logarithmic-sigmoid (logsig) and pure linear (purelin) transfer functions showed the best performance (R > 90%).

Oct 3, 2023

By N. Theron, R. F. Meeser

The global emphasis on conserving energy resources has led to the adoption of hybrid power systems in vehicles. Optimally applied, hybrid systems can save up to 40% on fuel costs. To optimally manage a hybrid vehicle's energy flow it is necessary to know, in real time, all the energy requirements to complete a given route. The energy consumption depends mainly on the vehicle mass, speed profile, and route topography. Of these, the topographic profile is the one factor that is only route-dependent and not influenced by the vehicle or driving styles. The heading vs. distance profile is also an example of a route characteristic not influenced by the vehicle or driving style. In this study the topographic and heading profiles are used to identify routes, and are easily measured by means of digital barometric pressure and compass sensors. Correlations between the current route and previously travelled/stored routes are performed based on their topographic and heading profiles in a point-by-point manner. Above-ground tests were first performed using a road vehicle and six routes to evaluate the system. The system consistently and correctly identified a 20 km route within the first 4 km. It also proved to function correctly in underground tests through the implementation of an instrumented hand-held surveyor's wheel. This system finds direct practical application in optimizing the energy management of an underground hybrid locomotive used by the mining industry in South Africa, but can also be of benefit in applications where route identification is required and using GPS is not feasible.

Jan 26, 2023

By C. T. O’Connor

Since the first IMPC took place in London in 1952 there have been many developments in our understanding of flotation, both in terms of chemical and physical factors influencing the process. Many of these developments have been captured in the proceedings of thirty congresses that have taken place since that first event, as well as in numerous journal papers and special volumes dedicated to flotation. This paper attempts to highlight the individual contributions which many eminent researchers and engineers have made over the past 70 years towards extending our understanding of, especially, the effects of chemical factors on flotation. Although the focus is mainly on more fundamental aspects, it seems that the ‘pull’ of practice has often preceded the ‘push’ from laboratory-based research. As the fundamental understanding of the role of chemical factors on flotation continues to be developed, the major challenge remains to transfer this knowledge effectively into the domain of operations of this profoundly complex process.

Jan 1, 2020

By B. Ndlovu

The world mineral industry has over the years experienced growth in the production of nickel (Ni) due to its use not only in the catalytic industry but mainly also to its demand in the stainless steel production industry. Hence there is a need to produce more pure and marketable grades of Ni through the use of efficient purification routes such as solvent extraction. The V10-LIX®84-IC system resulted in nickel (Ni) extraction isotherm shifting to lower pH levels. The pH window of opportunity for the extraction of Ni subsequently increased in solution containing magnesium (Mg) and calcium (Ca) even though the system also resulted in slight shifts to less positive pH values for Mg and Ca curves. Results showed a synergistic effect of LIX®84-IC when added to V10 for all elements, Ni, Mg and Ca. The pH50 values for elements Ni, Mg and Ca in the V10-LIX®84-IC system were 2.95, 8.10 and 7.70 respectively. Comparing results obtained when using V10 alone produced ?pH50 for Ni, Mg and Ca being 3.35, 0.15 and 0.70 respectively, which was a confirmation of the synergistic shifts for all the elements. The ?pH50 (Mg-Ni)value was 1.95 with no synergism and 5.15 with synergism and that for ?pH50 (Ca-Ni)was 2.10 with no synergism and 4.75 with synergism. This showed that the Ni-Mg separation factor was relatively larger than the Ni-Ca. Improved loading and stripping kinetics were also observed. Keywords: Nickel solvent extraction separation, magnesium, calcium, versatic 10 acid and LIX®84-IC.

Jan 1, 2008

On 8th August, 1973, 57 members of the Institute visited Prieska Copper Mine at Copperton in the North Western Cape. After tea, the group was welcomed by the Management of the Mine, and Mr Grobler, the General Manager, gave an introductory talk. After they had been taken on a bus tour of the property, the members split up into groups and proceeded underground or to the concentrator. Of special interest to the mining members were the rock-handling methods in use at the mine. The stoping method that has been adopted is the continuous, long-hole sub-level open stoping system. The broken ore is moved with rubbertyred front-end loaders from the stope drawpoints to the ore passes. On the main tramming levels, the ore is collected by electric locomotives and discharged into the main shaft system at the bottom. At the shaft ore-pass system, a gyratory crusher that can accept rocks up to 1 m in diameter has been installed. The crushed product (minus 150 mm in diameter) will then be hoisted by a Koepe winder, which has a rated capacity of 900 tons per hour. The mine is also served by a declined roadway from surface, which facilitates the movement of heavy equipment. The most striking aspect is the productivity that can be achieved by the use of a trackless-mining system. For the production of 230 000 tons per month, it is estimated that 6 stopers and 7 developers will be required. The total labour force will be approximately 2500-2000 Bantu, 200 Coloured, and 300 Europeans. Training of maintenance and operating personnel is of the utmost importance, and it was interesting to note the extent to which non-White labour is being used in these occupations. Lunch was served at the single quarters, after which the group proceeded to the airfield for the return trip to Johannesburg. On behalf of the visitors, Professor de V. Lambrechts thanked Mr Grobler and his staff for the most interesting morning and for their hospitality,

Jan 10, 1973

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

By M. Lu, E. Broch

Abstract: The formation and mechanism of rock cavern roof arches are studied and effects of rockbolts reinforcement are evaluated. It is concluded that a self-supported roof arch may be formed by the excavation. To stabilize such a roof arch, fully grouted rockbolts are effective. Tensioned cable anchors may have a negative influence on the arch stability. Zusammenfassung: Die Formation und der Mechanismus von Deckenbögen in Bergkavernen wird studiert und der Effekt von Verstärkung mit Bergbolzen wird bewertet. Es wird festgestellt, dass die Exkavation einen selbst-stützenden / freitragenden Deckenbogen formen kann. Eingegossene Bergbolzen sind effektiv um einen solchen Deckenbogen zu stabilisieren. Spannkabel können unter Umständen eine negative Einwirkung auf die Stabilität des Bogens haben. Résumé: Le mécanisme et la formation de voûtes dans les cavernes rocheures sont étudiés et l'effet du renforcement par boulonnage est évalué. Nous arrivons à la conclusion qu'une voûte autosupportêe peut être formée par excavation. Des boulons entièrement scellés par coulis de bêton s'avèrent efficaces pour stabiliser de telles voûtes. Les tirants d'ancrage peuvent quant à eux nuire à la stabilité de la voûte.

Jan 1, 2003

By X. H. Zhang, J. G. Cai

This paper discusses the behaviour of large-span tunnels and caverns in hard rock in a major underground storage project. In-situ stresses were measured using hydraulic fracturing during site investigation and 3-D overcoring during construction, with both showing a horizontal stress ratio of 2-3 times the vertical stress. Rock reinforcement design was based on the Q-system combined with numerical modelling for special design cases. Tunnel design and performance were checked and monitored by in-situ instrumentation during rock excavation, including measurements of deformation, convergence, and load on rock bolts. Deformation measurements using borehole extensometers included one borehole drilled into the virgin rock before rock excavation, which provided a direct and very insightful comparison with the various deformation measurements made during rock excavation. These measurements coupled with numerical calculations have proven that the high horizontal stresses to be very favourable to the stability of the large openings.

Jan 1, 2003

By G. E. Rencken, J. H. Potgieter, A. Narain, J. Smith

To conserve fresh water resources and comply with environmental regulations, DRDGOLD, a South African gold producer re-treating surface tailings, has transitioned to a fully closed water circulation system. Consequently, the accumulation of contaminants, as well as addition of reagents, has led to changes in water composition that have compromised leach performance and overall gold recovery. A two-sample t-test confirmed a significant difference in gold recoveries between the use of Rand Water, which was used as a benchmark, and untreated process water. Atomic absorption analysis of ERGO’s process water, confirmed the presence of iron, nickel, zinc, and manganese. A study of the effect of the identified contaminants on gold recovery showed that iron, nickel, and zinc have the largest negative effect on gold recovery, with iron and nickel being more detrimental than zinc. Sulphates were shown to have a possible passivation effect, which also influenced gold recoveries, although to a lesser extent than the heavy metals. Calcium, when present in excess, had a positive influence on gold recovery indicating the possible formation of a calcium aurocyanide complex. Lime softening successfully reduced the heavy metal and sulphate concentrations, and the gold recoveries obtained with the treated process water were similar to those as achieved with Rand Water.

Jul 1, 2021

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By D. deV. van der Spuy

A procedure for optimizing the secondary cooling zone of continuous casters is proposed and illustrated by a billet caster example. The procedure consists of quantifying deviations from the required conditions of the secondary cooling zone?as far as temperatures, metallurgical length and reheating are concerned?by means of a ?cost function?. The optimal spray settings are then found by minimizing the total ?cost?. The billet caster examples serve to emphasize the importance of specifying the required conditions in a consistent manner. Some envisaged practical limitations of this approach are discussed.

Jan 1, 1999

By G. van Aswegen

Large structures in mines (faults, dykes, pillars, abutments) fail when the load exceeds the strength. If the loading system stiffness (LSS, also referred to as the ‘local mine stiffness’) is lower than the stiffness of the structure the failure will be unstable. The greater the difference between these stiffnesses, the greater the energy release during unstable failure. A method has been formulated by which the LSS is established through cost-effective numerical modelling while insight into the structure stiffness (source stiffness - SS) is provided by apparent stiffness, a parameter based on the empirical relation between seismic moment and radiated seismic energy of small seismic events from the area/volume of interest. By plotting LSS vs SS a ‘stiffness diagram’ is constructed that is useful for seismic hazard ranking of different structures. A comparative back-analysis of the Dagbreek fault in Welkom, South Africa, (source of the 1990 Matjhabeng earthquake) and two other nearby faults confirm the applicability of the method. An extension of the method, where ‘hazard magnitude’ is used as a measure of the LSS, allows a ‘stiffness diagram’ to be constructed using seismic data only. Les larges structures dans les exploitations minières (failles, dikes, piliers, culées) s’écroulent lorsque la charge dépasse la résistance. Si la raideur du système de chargement (LSS, aussi appelé la « raideur de la mine locale ») est plus basse que la raideur de la structure, l’éboulement sera instable. Plus la différence est grande entre ces deux raideurs, plus l’énergie dégagée pendant l’éboulement instable est grande. Une méthode a été formulée selon laquelle le LSS est établi par modélisation numérique rentable, tandis que la raideur de la structure (SS – raideur de la source) est établie par la raideur apparente, un paramètre basé sur la relation empirique entre le moment sismique et l’énergie sismique radiée de petits moments sismiques dans l’aire/volume en question. On trace le « diagramme de raideur » en relevant les deux mesures (LSS et SS), ce qui est utile pour classer les risques sismiques de structures différentes. On vérifie l’applicabilité de la méthode en comparant la faille de Welkom, Afrique du Sud (foyer du séisme de Matjhabeng en 1990) avec deux autres failles proches. Une extension de cette méthode, dans laquelle on utilise la « magnitude du risque » comme mesure du LSS, permet de construire le « diagramme de raideur » avec des données sismiques seulement. Große Strukturen in den Gruben (Verwerfungen, Dämme, Pfeiler, Auflager) scheitern, wenn die Last die Stärke übersteigt. Wenn die Steifheit des Ladesystems (LSS, auch bezeichnet als `lokale Grubensteifheit’) niedriger ist als die Steifheit der Struktur wird der Bruch instabil. Je grösser der Unterschied zwischen diesen Steifheiten, desto grösser die Energiefreigabe während des instabilen Bruches. Es wurde eine Methode formuliert, durch die das LSS durch eine kosteneffektive numerisches Modell erstellt wird, während ein Einblick von der offensichtlichen Steifheit in die Struktursteifheit (Quellensteifheit - SS) gegeben ist, ein Parameter der auf der emipirischen Relation zwischen seismischem Moment und ausgestrahlter seismischer Energie von kleinen seismischen Ereignissen vom Interessens-/Volumenbereich basiert. Durch das Kartograpahieren der LSS in Bezug auf die SS wird ein `Steifheitsdiagramm ' konstruiert, welches für seismische Gefahrklassifizierung der unterschiedlichen Strukturen nützlich ist. Eine vergleichende Postanalyse der Dagbreek Verwerfung in Welkom, Südafrika, (Zentrum des Matjhabeng Erdbebens 1990) und in zwei anderen nahe gelegenen Verwerfungen bestätigen die Anwendbarkeit der Methode. Eine Verlängerung der Methode, in der die `Gefahrengröße' als Maß für das LSS verwendet wird, gestattet, daß ein `Steifheitsdiagramm' konstruiert wird, welches nur seismische Daten verwendet.

Jan 1, 2003

By M. M. D. S. Vemba

Paper written on project work carried out in partial fulfilment of B.Sc. Eng (Mining Engineering) degree Engineering refers to the application of mathematics and other sciences to logically develop solutions to problems. However, in opencast mining, due to the randomness of operations, the use of mathematics is often neglected. Instead, practices that have proven successful elsewhere tend to apply. At the other end of the scale, mathematical models have been developed to identify and quantify all the operational parameters involved in the loading and haulage of ore. These are then used to optimize the operation. Optimization in this context, refers to the reduction of cost through effective utilization of the available time and resources. Considering these mathematical models, the loading and transport system at SMC (Catoca Mining Society) will be assessed with a view to its optimization. The discussion will be introduced by considering the mine background and other general information, which will highlight the main operational variables.

Jan 1, 2004

By D. Janicijevic

This paper describes the process of scraper winch pull force measurement and shows the results of the actual winch pull force in extreme stall situations as well as during the face and gulley cleaning. It was found that by slowing down the motor and causing it to slip, torque up to 3.5 times higher than the nominal can be developed, resulting in the same increase of winch pull force. On the other hand, measurements of the actual force needed for cleaning of the face and the gully have shown that the currently used winches are too powerful. The extra torque that can be developed by the already too powerful winch motor poses a significant danger and necessitates the implementation of measures that will eliminate this risk.

Jan 1, 2008

By H. Hu, T. S. Golosinski

The paper reports on use of neural network algorithms to model performance and condition of mining trucks. The model inputs are selected digital data streams collected by truck Vital Information Management System, VIMS, during its operation in a mine. The models built as the result of this work allow for projection of truck condition and performance into future. As such they facilitate more efficient management of mine truck fleets. Keywords: Modelling, modeling, neural networks, mining equipment, Vital Information Management System, Intelligent Miner, mining truck

Jan 1, 2003

By G. Westcott

Impala Platinum, the second largest platinum producer in the world, is embarking on a major expansion strategy to increase its platinum output from 1.95 moz to 2.8 moz by the year 2008. The smelter complex, situated in Rustenburg, will undergo substantial modifications, and will require a solution to the capture and treatment of the smelter off-gases and dust produced during smelting and converting operations. One of the solutions explored was an integrated approach, where all the off-gases from both the primary smelting electric furnaces and the converter operations are routed to a large central gas cleaning and double catalysis, double absorption acid plant. In-line sulphur burning, utilizing a highly flexible LURO1spin cup burner with a turn down ratio of 50%, ensures that the acid plant operates independently of operating conditions at the smelter complex.

Jan 1, 2007

By C. J. Cutler

Metallurgical accounting for toll treatment smelters pose a number of challenges. Multiple feed stockpiles have to be accounted for as part of the monthly recovery estimation. Moreover, multiple metallurgical intermediates make up part of the in-process inventory, which also influence the monthly recovery calculation. Errors propagate from the measurements of volumes, assays, moisture fractions and bulk densities in the various material types through multiple steps up to the point where the final recovery is calculated. These errors contribute non-linearly to the variance in the final recovery estimate. This paper develops the mathematical formulation for variance propagation in toll smelting operations, including the effect of in-process inventory, assuming measurement biases have been eliminated beforehand. Operational data from a Southern African copper smelter is used for a case study. The method of propagation of variance showed that uncertainties in stockpile assays were the main contributors to variance in the recovery estimate. Variance in the volume and bulk density uncertainties contributed a secondary, yet significant, proportion to the overall recovery variance. It was determined, for the given case study, that the recovery variance depended on the calculation method used and that variance propagation via the two-product formula was smaller than recovery variances calculated via the standard recovery formula. However, the probability that the two product formula will give inaccurate (versus imprecise) results is significantly more due to the practical difficulty of equiprobable sampling of tailings streams from smelter plants (which includes materials such as slags and flue dust). Recommendations are made on how to achieve a reduction in overall uncertainty for toll treatment smelters. Keywords: metallurgical accounting, copper smelters, pyrometallurgy, variance propagation, errors, precision, sampling

Jan 1, 2006

By Y. He

The nature of the density distribution in a gas-solid phase fluidized bed for dry coal separation is an important factor in influencing the performance. However, during coal processing, fine slime would mix with dense medium of magnetite powder and accumulate in the bed, and its influence will affect the density of the bed. The mathematical model of the density distribution with fine slime behaviour was studied in an experimental laboratory system. The functional relationship between the density of the air dense medium fluidized bed and the coal slime content were fitted, applying the principle of least-squares method with damping factors. With the model, by analysing the trial testing data, the mechanism of the density distribution of the bed was studied and applied to a coal separation test with a pilot scale separator. Keywords: dry coal separation, gas-solid phase, model fitting.

Jan 1, 2002