Search Documents

By T. A. Muhlare

The use of electrolyte additives to smoothen cathode deposits during copper deposition is practised worldwide. These additives absorb on the cathode surface and take part in the electrochemical crystallization process. However, these additives also affect the quality of the cathodes when they are inadequately controlled. Electrolyte additives used by Palabora are glue, thiourea, Avitone and chloride. Their effects were determined on cathode quality, the size of the current density region that gives the desired compact morphology, and current efficiency. This was done in a small-scale cell. Small cells have different hydrodynamics from industrial-scale cells, which makes it difficult to simulate the operation of industrial cells in a laboratory. The approach used here was to use a rotating cylinder cathode to attain controlled hydrodynamics. The rotation speed was chosen to give a diffusion layer thickness that is similar to that of an industrial-scale cell. It was shown that even fairly small changes in the additive levels can significantly affect the cathode morphology, and the current density range over which this morphology can be obtained. Keywords Copper, electrorefining, glue, thiourea, avitone and chloride.

Jan 1, 2011

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By G. L. Smith

This paper introduces and defines the concept of a linkage between long-term planning parameters (?global assumptions?) and possible future world views as conceived in scenario planning. Scenario planning, the tool that is used to arrive at plausible future worldviews, is described in the context of the platinum industry. The interpretation of the scenarios into long-term planning parameters is made, followed by an illustration of how the long-term planning process has been adapted at Anglo Platinum to include the notion of uncertainty.

Jan 1, 2008

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By P. S. G. Leon

One of the most difficult areas in concession contracts in resource-rich developing countries is achieving an equitable balance between the interests of investors, host states and, increasingly, mine and near mine communities. While some countries in the Andean region have resorted to outright or creeping expropriation of natural resource contracts under the guise of resource nationalism, others such as the Democratic Republic of the Congo (DRC), have claimed international best practice in the review (and setting aside) of important concession contracts.

Jan 1, 2011

By S. H. Yi, J. R. Kim, Y. S. Lee

The viscosities of CaO-SiO2-Al2O3-MgO-FeO slags were measured under conditions ofCaO/SiO2=1.15–1.6, 10–13 percent Al2O3, 5–10 percent MgO and 5–20 percent FeO. Slag viscosity decreased with increasing FeO content at a fixed basicity (CaO/SiO2) of slag. Slag viscosity at low FeO (<7.5 percent FeO) exhibited a minimum value by increasing MgO content in slag. Viscosity decreased with increasing slag basicity up to 1.3 while it increased as slag basicity increased from 1.3 to 1.5. Thus, it was proposed that the driving force for the decreases of slag viscosity would be an increase in depolymerization of silicate network at C/S=1.3, while the viscous behaviour at C/S>1.3 would be increased with increasing the chemical potential of primary solid phase e.g. dicalcium silicate. A thermodynamic approach for the activity of primary solid phase in molten slags resulted in a reasonable relationship between viscosity and slag components. Therefore, it was confirmed that slag viscosity in basic slags system (C/S>1.3) could be determined by the chemical potential of dicalcium silicate. Keywords: viscosity, basicity, bosh slag, blast furnace, slag structure, FT-IR

Jan 1, 2004

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004

By C. Dixon

This paper is based on the assumption of some knowledge of the National Water Act. It will consider the question of how that Act fits in with: a) existing laws which overlap on the subject matter b) new laws either in draft or in the process of being compiled c) policies which will eventually find their provisions included in new legislation (e.g. minerals policy) d) international practices. The focus will be specifically on the interaction of legislation relating to water use and water pollution in the mining sector as well as the role of the Department of Water Affairs in mining matters. Hence the title of the presentation.

Jan 1, 1999

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By Sergio Burelli, Darren C. Megaw

"Operational challenges associated with solvent extraction (SX) plants include the effective on-line management of solids introduced from a variety of process streams. Solids are carried over from leaching circuits due to incomplete solid–liquid separation, may be formed as a result of chemical precipitation within the SX circuits, or introduced from downstream electrowinning operations. Solids in SX settlers result in operational challenges that impact plant availability and reduce optimized name-plate design capacity operation. Most available SX crud and bottom solids removal systems are limited in their effectiveness to handle high total suspended solids in SX circuits. Operations are often forced to take settlers off-line for complete removal of contained solids. These cleaning operations are hazardous, high risk, labour-intensive and costly in terms of production down-time and organic extractant and diluent reagent losses. Production pressure results in operations being reluctant to take SX settler units off-line for solids clean-out, resulting in continued operation of the SX, at reduced levels of mass transfer performance. Crud ForxTM is an SX solids removal system, for the on-line removal of interfacial and bottom solids associated with hydrometallurgical SX processes. A case study conducted at Glencore’s Mutanda Mining copper and cobalt operation in the Democratic Republic of Congo demonstrated the effectiveness of the Crud Forx. Benefits identified were an overall improvement in SX fire risk reduction, SX occupational health and safety and an improvement in copper mass transfer. INTRODUCTION Hydrometallurgical copper extraction and purification processes are often associated with ultra-fine solids distribution profiles throughout the process flowsheet (Virnig et al., 1999). The level and impact of the undesired deportment of solids to process streams varies from operation to operation, but the common denominator for all operations that employ solvent extraction (SX) as a copper upgrading and purification step is that, at some stage, they will have to manage solids (crud) within the SX circuit. Available crud removal systems in the industry have had limited success in continuous, effective interfacial crud and bottom solids removal from SX settlers. Most operations use basic removal methodologies which, at best, only result in delaying the requirement for taking the affected SX settler stages off-line for complete clean-out. This operational methodology results in production loss, increased SX organic extractant consumption and adds occupational health and safety risk to SX operations. The integrated Crud ForxTM/Crud FrogzTM SX solids management system assists operations in on-line SX solids management. The system has been proven to significantly reduce the requirement for off-line cleaning of settlers."

Jan 1, 2015

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004

By E. Kapilashrami, S. Seetharaman

Refractory/metal interactions and associated reactions are significant during casting as they can lead to inclusion formation. High-temperature interactions between aluminosilicate refractories and molten steel were studied in the present investigation using the sessile drop method. The changes in the contact angles between molten iron with well-defined oxygen levels and substrates of silica, mullite (3Al2O3?2SiO2) as well as commercial refractories were measured in the dynamic mode. In all cases, the reaction led to slag formation. The experiments were performed under isothermal conditions at 1823 and 1873 K. A known and constant oxygen partial pressure was imposed above the iron drop, through appropriate CO-CO2-Ar mixtures. For all substrates, the contact angles started decreasing due to the lowering of the surface tension of iron, as oxygen was imposed on to the system. When a critical level of oxygen was reached, slag started forming at the drop/substrate interface and at this stage, the contact angle dropped suddenly. Subsequent behaviour of silica and mullite was observed to be different, with SiO2showing a non-wetting behaviour. In the case of SiO2substrate, there were also deep erosions along the periphery of the drops and there was slag accumulation at the sides of the metal drop, probably due to Marangoni flow and/or SiO(g) formation. SEM and EDS analysis of the substrates revealed that the formed slag was fayalite. The thermodynamic criteria for slag formation and possible mechanisms of the reaction are discussed in the light of the experiments. Key words: silica, mullite, fayalite, corundum, slag formation, sessile drop.

Jan 1, 2004

Council for 2004/2005 President F.M.G. Egerton President-elect W.H. van Niekerk Vice-presidents Senior R.P.H. Willis Junior R.G.B. Pickering Immediate Past-president T.R. Stacey Honorary Treasurer J.A. Cruise

Jan 1, 2005

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By R. Peroni, J. Kopp

Mine planning and scheduling is based on using a geological model for the deposit. Blocks are used to discretize the deposit into mineable volumes where grade values are assigned. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for this task where an interpolated value is calculated within a discrete volume. This group of block grades is the input for sequence optimizers, which base their decision on the economical value of a given block. Ultimately, the economical value of a block depends on its grade, making mine sequencing sensitive to all estimated values. If one looks to a block not as a single grade but as a set of equally possible grades, its economical value will change as different grades can be assigned to it. Stochastic simulation is known to provide the tools to assess grade variability, which makes it possible to generate equally probable values in a block. Different grade block models can thus be built and multiple sequencing alternatives are observed by running the optimizer for these distinct inputs. The results demonstrate that the methodology is adequate for risk assessment and proves to be useful for mining project sensitivity analyses. Differences in the project net present value showed that there is little difference between the two simulation methodologies (sequential Gaussian simulation and sequential indicator simulation) applied. The process is demonstrated using a Brazilian kaolin deposit. Keywords: geostatistical simulation, mine planning, sequencing, risk assessment, open pit optimization.

Jan 1, 2003

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

By S. J. Frank

The development of feedforward semi-empirical control models for furnaces and the evaluation of mass balances are based on plant data. The models can only be as good as the data and it is therefore required to know the inherent uncertainty associated with the plant data. This uncertainty stems mainly from the fact that the slag, alloy or dust, have a distributed nature that depends on the degree of mixedness. It is commonly accepted that melts from open bath furnaces are well-mixed, and submerged arc furnaces less so. The impact of this assumption is significant, as a reasonably homogeneous melt could be represented by one sample only. As so much of metallurgical control depends on the assay information of the alloy and slag melts from furnaces, it was decided to characterise the possible variation in melt chemistry and temperature. Sampling campaigns and continuous temperature measurement of the melts were performed for different alloy and slag taps at a major ferrochrome producer. Both a submerged arc furnace and open arc furnace are evaluated in this way, by way of comparison. The slags of both open arc and submerged arc furnaces were found to be of similar degrees of homogeneity, with much spatial variance in the reducible iron and chromium oxides. However, it was found that the alloy melts deriving from open arc furnaces were significantly less homogeneous than the alloy derived from submerged arc furnace alloy production. The compositional variance could be related to the furnace operating conditions and it affects both metallurgical accounting and process control. In all cases it was found that the variance in melt solute components are larger than can be ascribed to analysis instrument error. It will be shown how this predetermined variance in melt composition could be included in process modelling and control.

Jan 1, 2004