Search Documents

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By V. Brabie, S. Jansson, L. Bohlin

The rate of dissolution of solid MgO-C and doloma into liquid in CaO-Al2O3-SiO2-MgO slag at different temperatures was studied under conditions of forced convection by rotating cylindrical refractory specimens in a stationary crucible containing the molten slag. The corrosion rate was calculated from the change in diameter of the cylindrical specimens. Refractory specimens were 13 mm in diameter and 70 mm long. The specimens were rotated for15 to 120 minutes at speeds of 100 to 400 rpm in the molten slag. The rate of corrosion increased with temperature and with the rotating speed of the rod, and decreased when the slag was nearly saturated with MgO. The experimental results confirm the assumption that the diffusion of magnesium oxide through the slag phase boundary layer controls the corrosion process. The corrosion mechanism seems to be the dissolution of the refractory materials into the slag, followed by penetration of pores and grain boundaries and dispersion of the grains in the slag. Keywords: MgO-C refractory, doloma refractory, molten slag, corrosion rate, corrosion mechanism

Jan 1, 2004

By M. R. Samis

The great variability of mineral and energy prices has motivated some governments to incorporate a windfall profits tax into their mineral taxation regimes. Windfall profits taxes are a means for governments to capture additional mineral revenue when mineral prices are considered higher than some historic level. Governments need to be aware of the effects of such contingent taxes on the exploration, development and operating decisions of mining companies. Mining companies need to be able to calculate the full impact of windfall profits taxes on the economics of their projects. This paper examines the valuation of a multi-phase copper-gold project in the presence of a windfall profits tax. Real options Monte Carlo simulation is used to characterise the different exposures of the mine owner and of the government to the risky cash flow streams that they receive from the project. The results highlight that Monte Carlo simulation paired with the real option valuation method is able to account appropriately for the differing risk exposures, while the traditional discounted cash flow valuation model is not. Our key conclusion for governments and mining companies is that the impact of contingent tax and royalty terms can and should be assessed using advanced valuation techniques, and the results used to improve contract designs under the constraint of actual and perceived fiscal system stability.

Jan 1, 2007

By L. Rademeyer, P. Mazzoni, C. Kubank, F. Brown

The Corridor Sands deposits of heavy mineral sands represent the largest known economic resource of titanium dioxide minerals. The West Block of Deposit 1 alone contains Measured and Indicated Mineral Resources of 1.7 billion tonnes containing 4.14 per cent ilmenite, estimated in accordance with the JORC standard, sufficient for at least the first 20 years of mining. Total mineral resources are estimated to be approximately 17 billion tonnes at 5 per cent Total Heavy Minerals (THM). Test work was undertaken on the West Block of Deposit 1 over a period of two years in order to develop the process flow sheet to bankable standards. Geological, mineralogical and metallurgical test work was integrated from a pre-feasibility stage to the full bankable stage. The process flowsheet was developed with the central objective of the production of saleable products, of consistent quality and acceptable to the respective end-markets. The aim of this paper is to describe the way in which the various challenges for the project have been addressed by using integrated geological and mineralogical information, which has resulted in the development of a complete flow sheet. The process confirmed that material within customer specifications could be produced, once various metallurgical parameters were understood. This flow sheet development progressed from laboratory test work through to full field trials at pilot plant scale on large consignments of mineralized material. The flow sheet was developed to such a standard as to be used with confidence for both engineering design and cost estimates, and to determine the recovery factors to be used in financial evaluations. Keywords: Corridor sands, Flow sheet, Pilot plant Titanium dioxide

Jan 1, 2003

By D. J. Fourie

During the production of pure TiO2for the pigment industry, ilmenite, containing 35?60% TiO2, is reduced to high titania slag, containing 70?95% ?TiO2? and pig iron. The high titania slag produced, consists mainly of titanium in different oxidation states and FeO in equilibrium with liquid iron. To predict the phase and chemical reaction equilibria in a furnace, a suitable solution model is required with accurately determined binary interaction parameters, as slag melts tend to behave very non-ideally. This paper investigates two popular slag models, namely, modified quasi-Chemical (MQC) model and the cell model and provides the binary interaction parameters based on recently published data of the ternary system and critically assessed published unary and binary data. Very few modelling results have been published on the ternary Ti-Fe-O system pertaining to high titanium slags. The solution models, with their regressed interaction parameters, can subsequently be implemented in commercial software of the slag-metal phase equilibria to predict how much and which type of solids will precipitate for a given bulk slag chemistry and operating temperature or, alternatively, above which temperature should a furnace be operated to avoid excessive solids precipitation.

Jan 1, 2005

By N. McEwan

Keywords: refractories, chromite, Marico This paper examines the role of refractory-grade chromite in refractories. The chromite deposit at Verref?s Marico Chrome mine is described. The refractory properties of chromite and their role in basic refractories are described. The properties and metallurgical applications of chrome-containing refractories are described and finally environmental issues associated with chrome-containing refractories are discussed.

Jan 1, 2011

By W. Biermann

All industrial processes are economically driven, resulting in the ever increasing need for process optimization in order to stay competitive and profitable. Numerous models has been published depicting the optimization of the raw material usage in an arc furnace, as well as the thermal and electrical efficiency; however, to obtain a holistic view of the cost-effectiveness of the process one needs to expand the model to include the cost of all the operational variables. This project therefore aimed to not only include the raw material feeds and power consumption as input variables, but also the labour, maintenance, and environmental costs to generate an all-inclusive financial balance. In the end, the model was able to mathematically optimize the ferrochrome (FeCr) production process through evaluating the effect of a specified combination of input parameters. It could therefore be used as a tool to aid in managerial decision-making; to appraise and correspondingly adjust certain operational variables in order to achieve a maximum return on investment. This paper fully describes the reasoning behind the choice of the essential model components, the assumptions made during the models development, the calculation approach, as well as the advantages, limitations, possible applications, and areas for expansion of the final model. Through running simulations with plant data, it was found that the accuracy of final model remained fairly constant when applied to stable furnace conditions, but was met with a number of limitations when applied to more complex situations. These limitations could, however, be overcome through further development and expansion of the existing model to include a larger number of process variables.

Jan 1, 2012

By N. F. Mescheriakov

New mechanical and pneumatic-mechanical flotation machines with axial impellers have been developed. Industrial tests show that these machines ensure lower power expenditure (on flotation) by 1.5-2.0 times as compared with reference machines (with the same or improved technological indices). Application of the newly developed axial impeller, with these advantages, is possible in any volume chambers of type OK, Dorr-Oliver, Wemko etc.

Jan 1, 1998

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"The purpose of the study was to investigate the feasibility of SiC reduction of low-grade concentrates from Lonmin’s Rowland and Easterns operations with respect to metal fall and PGM recovery. These concentrates are rich in SiO2 and MgO with low concentrations of chalcopyrite and Cr2O3. Pd is the most abundant of the PGMs. SiC reduction of samples was conducted at 1600? with 2.5-3.5 kg SiC per 100 kg concentrate.PGM recoveries for Easterns concentrate were better than for Rowland. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered with 3.5 kg SiC per 100 kg concentrate. SEM of slag samples showed little entrainment of metallic prills compared to Rowland samples. This was attributed to the relatively higher melt viscosities of the Rowland concentrate. In order to decrease slag viscosity and to enhance PGM recovery, the FeO content of the Easterns concentrate was increased with the addition of 10 kg converter slag per 100 kg concentrate. Ir and Pd recoveries were increased to about 95%, while Pt recovery was around 70%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and converter slag is proposed. Carbothermic reduction of the optimum charge was also compared to SiC reduction. Carbothermic reduction yielded a marginally higher metal fall; however, the calculated gas emissions and energy requirements were higher than for SiC reduction."

Jan 1, 2015

By D. M. Mubita

Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programmes require interaction on a multi-disciplinary level. This paper outlines recent initiatives undertaken at Konkola Mine to reduce dilution and increase revenue. The increase in revenue arising from reduced dilution and high factors between in situ and delivered to mill grades were quantified and amount to close to U$ 1.0 million per one per cent improvement in grade factor at a 75c/lb copper price. Sources of dilution from open and in?stope mining methods practised at the mine were identified and a multi-disciplinary dilution control forum set up to control these. Among the major achievements were the introduction of low dilution in-stope mining methods; the introduction of Gemcom geological and mining planning software to replace traditional pencil and paper methods, leading to better in situ estimation and production planning; enhanced control in open stopes through dilution awareness among mining production personnel; location of critical secondary development ends in correct positions; enhanced blast hole control; tracking of development waste by metal tracers and monthly tally; implementation of a cavity monitoring system to check over-breaks in open stopes; and setting up of a stope history database. The results from the cavity monitoring system showed that stopes with over-breaks of 5 metres or less could be controlled to break along the hangingwall contact.

Jan 1, 2005

By Mauri Kauppi, Pekka Niemelä

World HCFeCr production is 6.0 million tonnes. Correspondingly 1.1-1.6 t slag / t FeCr is produced depending on the raw material basis. Essentially all FeCr is produced in submerged arc furnaces, while the role of competitive technologies like DC is limited. In all furnaces fluxes are used to optimize the slag composition. Vital characteristics are smelting point, electric conductivity and viscosity. The main components of FeCr slag are SiO2, Al2O3 and MgO. Additionally it consists of Cr-, Fe-oxides and CaO. Granulated slag and/or classified slag products are produced depending on the production process. The slag products are mainly marketed in road and civil construction purposes but also in producing refractories. Normally crushed and screened slags are produced simultaneously when recovering alloy. The leachate of slag products is low and performance results are excellent. Slag products successfully replace natural sand and macadam. Generation of waste is essentially reduced. Producing and using slag products are described as BAT-technology and it is an essential environmental aspect. Outokumpu Tornio Works produces 320 000 t FeCr-slag/a. This paper deals with formation of slag in smelting process, its chemical composition, physical and structural characteristics, utilization and product specifications as well as environmental aspects. The slag products are standardized and CE marked. Additionally the role of slag in smelting and alloy recovery is reviewed in this paper.

Jan 1, 2007

By W. S. Steinberg

In 1963, the full-scale engineering study for the development of an iron, steel, and vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steelworks that produced steel and vanadium-bearing slag from a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for prereduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to open slag bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of the higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

Analysis for pillar extraction potential (A-PEP) is an intelligent tool, which could be used as a preliminary output indicator when considering the secondary extraction of regional support pillars in the Witbank and Highveld coalfields of South Africa. The safe and economic extraction of underground coal pillars is of paramount significance and importance to the South African coalmining industry to ensure continuity of supply of this fossil fuel. Pillar extraction practices in South Africa have been responsible a significant proportion of safety and fatality statistics in relation to its relative output (less than 5 per cent of total South African coal production) and, as a result, research was undertaken in local pillar extraction operations and extended to similar operations in New South Wales, Australia to assess a way forward for pillar extraction in South Africa. It was found that, although little in the way of new technologies has emerged in this field in the recent past, significant contributions could be made in the field of risk analysis to obtain a generic design methodology for pillar extraction in South Africa. The resultant A-PEP tool to assess pillar extraction potential is based on certain physical, risk and economic factors, which combine to indicate operational success in terms of economic, health and safety attributes. At the time of A-PEP?s development there was alack of operating underground coal pillar extraction operations, which made it difficult to validate its applicability. Since then, however, A-PEP has been successfully tested and validated against two unique underground coal pillar operations, which is the discussion of this paper. One operation is situated in the Witbank coalfield and is extracting pillars, which are 20 years old and at a depth of 80 metres below surface, while the other operation is situated in the Highveld coalfield-which is extracting 6 month-old-pillars underneath a massive dolerite sill at a depth of 220 metres. A-PEP has shown that its predictive nature is consistent the workings at both operations, irrespective of their unique conditions, and as such it can be successfully used as a mine planning tool. The A-PEP mine planning tool thus represents a positive step toward an integrated approach to underground coal pillar extraction when considering legal and operational aspects, which could form the basis for legislative guidelines when considering the future of pillar extraction in South Africa.

Jan 1, 2005

By David Colloby, Darelle T. Janse van Rensburg

Premature coating failures of new and refurbished structural steelwork of clarifiers have been a common occurrence at power generation plant in recent years. Several of these failures have ended in disputes regarding which party was actually to blame for the early degradation of the coating system, i.e. quality of the power station?s water, poor application, substandard materials, outdated corrosion protection specifications, etc. Having investigated several of these premature failures, it is clear that the corrosion protection of clarifier steelwork is a highly complicated process and that the painting work needs to be closely monitored in order to ensure long-term protection by whichever product that is applied. The need for quality control inspections during the painting of the plant is often underrated during the project planning stage, also the importance of detailed corrosion protection specifications that consider not only the practical application of the materials, but also the quality control responsibilities of the Contractor, End User and Third Party Inspectorates that may be involved. This paper considers the application constraints of coatings to clarifier structural steelwork and importance of stringent quality control procedures in order to ensure the long-term performance of the corrosion protection systems.

Jan 1, 2006

By F. R. Camisani-Calzolari

Surface defects on continuously cast slabs require treatment by grinding. This extra phase in the process causes lower throughput of final product and extra energy costs. The elimination of slab treatment after casting implies that slabs can be direct rolled or hot charged, resulting in higher throughput and lower energy costs. To increase the number of slabs that can be direct rolled or hot charged, defects have to be predicted before a slab has completed the casting process. Transversal and longitudinal cracking, casting powder entrapment and other inclusions, bleeders, deep and uneven oscillation marks, stop marks and depressions are the defects thatare considered for prediction. A structure with two models is proposed. The first model describes the effect of mould level, water inlet temperature and casting speed (MV?manipulated variables) on 38 thermocouple temperatures (IV?intermediate variable). Casting speed is a manipulated variable while mould level and water inlet temperature are treated as measured disturbances. This model is known as the MV to IV model, and is used to control the occurrence of defects. The second model describes the effect of the thermocouple temperatures on the defects at different positions and locations on the slabs (OV?output variables). This model is known as the IV to OV model and is the predictor of defects. The models are determined using time-series methods in the form of auto regression with exogenous input using data of approximately 500 slabs cast over a period of 6 months. The models are validated using plant data from 44 slabs gathered three years later, with good results. As an example, published results give a sensitivity and specificity of 61.5 per cent and 75 per cent respectively for longitudinal cracks on validation data, while the presented method gives 63.6 per cent and 93.5 percent, respectively. The IV to OV model is used in an inversion to determine the optimal thermocouple temperatures for each slab width. Keywords: Continuous casting, model, defect, prediction, direct rolling, hot charging, goodness-of-fit, correlation, time-series, soft sensor, ARX.

Jan 1, 2003

By G. de B. van Niekerk

This paper briefly outlines some mining technology that is used with success in Australia but is not yet fully utilized in South Africa. The following aspects are discussed: improved rotary-drill bit performance, use of trucks and load haul- dump units underground, long-hole raising, blasting techniques, and the use of butterfly roofbolt plates for support.

Jan 1, 1989

By H. Zhu

Coal desulphurization by flotation is often difficult due to the surface oxidation of coal pyrite. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were adopted to obtain detailed information about the surface oxidation of pyrite. Fresh pyrite surfaces were found to be hydrophilic, and to turn hydrophobic after initial oxidation, with oxidized products such as polysulphide FeSx and free sulphur. The oxidized products on the pyrite surface were reduced by an electrochemical method, returning the surfaces to a hydrophilic state and thus increasing the separating efficiency of coal from pyrite by flotation. Key words: surface oxidation, pyrite, SEM, XRD pattern, electrochemical modification.

Jan 1, 2002

By M. Kumral

The efficiency of an ore-processing unit depends on the consistency of the characteristics of raw material entering the plant. When the mined ore is highly variable in quality, the only way to ensure consistency is to homogenize the ore prior to feeding to the processing plant. The homogenization can generally be achieved by the bed blending operation. Given that the stockpiling and reclamation processes are very expensive, it is necessary to design the process in such a way as to minimize variabilities of specified properties of raw material. In this paper, for alternative stacking types, optimal stockpile geometry is found in three stages: First, stockpile input is simulated by sequential Gaussian simulation, and then the variance reduction ratios (VRR) as a criterion of stockpile efficiency are calculated for various stockpile geometry scenarios by a stockpile simulator written in FORTRAN. Second, multiple regression analysis is performed to model the VRR by the use of stockpile length, the number of layers and stacker speed as the independent variables. Finally, the model is an optimization problem. Decision variables are the stockpile length, the number of layers, stacker speed and stacking type. The genetic algorithms (GA) are used to minimize the VRR. The approach was demonstrated on data from an iron orebody. The problem was to reduce fluctuations of iron, silica, alumina and lime contents in the stockpile output. The results showed that the approach could be used for the bed blending design efficiently. Keywords: bed blending design, multiple regression analysis, genetic algorithms, iron ore, content fluctuation

Jan 1, 2006

By R. Hansson

Zincite and spinel phases are present in the complex slag systems encountered in zinc/lead sintering and zinc smelting processes. These phases form extensive solid solutions and are stable over a wide range of compositions, temperatures and oxygen partial pressures. Accurate information on the stability of these phases is required in order to develop thermodynamic models of these slag systems. Phase equilibria in the Fe-Zn-O system have been experimentally studied for a range of conditions, between 900 and 1580°C and oxygen partial pressures (pO2) between air and metallic iron saturation, using equilibration and quenching techniques. The compositions of the phases were measured using Electron Probe X-ray Microanalysis (EPMA). The ferrous and ferric bulk iron concentrations were determined using a specially developed wet-chemical analysis procedure based on the use of ammonium metavanadate. XRD was used to confirm phase identification. A procedure was developed to overcome the problems associated with evaporation of zinc at lowpO2s and to ensure the achievement of equilibria. An isothermal section of the system FeO-Fe2O3-ZnO at high ZnO concentrations at 1200°C was constructed. The maximum solubilities of iron and zinc in zincite and spinel phases in equilibrium were determined at pO2=1*10-6atm at 1200and 1300°C. The morphology of the zincite crystals sharply changes in air between 1200 and 1300°C from rounded to plate-like. This is shown to be associated with significant increase in total iron concentration, the additional iron being principally in the form of ferric iron. Calculations performed by Fact Sage with a thermodynamically optimized database have been compared with the experimental results. Keywords: Phase Equilibria, Fe-Zn-O, Quenching, Wet-Chemistry, EPMA, XRD, ISP.

Jan 1, 2004

By N. Hanief

This research involves the investigation of phase transformations in the platinum-chromium coated system. Single-layer 0.1 µm platinum coatings were deposited via electron beam deposition on 99.98 percent pure chromium substrates. Specimens were subjected to systematic heat treatment in a vacuum furnace at 900°C for up to 20 hours. Phase formation and the changes in surface morphology were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM).Both CrPt and Cr3Pt phases are formed during heat treatment for different times at 900°C. Significant changes in the morphology of this coated system were detected after heat treatment at 900°C for 20 hours.

Jan 1, 2012