Search Documents

By J. F. Barkley

"A knowledge of the carbon dioxide (002) content of the products of combustion, particularly from the boiler furnace, is very valuable. An instantaneous indication of the CO2 can be used as a useful guide to efficient burning. A permanent record over a. period of time gives a story to the management which tends to keep the operators more alert. Many instruments that indicate and record CO2 have appeared within the last fifteen years. More are about to appear. Although simple principles involving chemical, physical, or electrical qualities, are being used, there is at present a general feeling of uncertainty about such instruments in the boiler room any instruments are bought, run awhile, then lie idle indefinitely.Inquiries as to CO2 machines continually come to the Bureau of Mines from the general public, as well as from other branches of the Government. Some ten years ago a series of tests was made on certain instruments at that time on the market. The following test was made quite recently on four of the newer types, including one using an electrical principle. The four instruments were installed on one boiler each, according to the instructions of the makers, and the recommended routine attention was given them. The test was of a service nature duplicating the conditions under which the instruments ordinarily serve. The boiler that was available for this purpose was practically banked for some hours of the night. This caused the average CO2 for the entire twenty-four hours to be rather low, although it reached the higher ranges of the instruments during the day.Each day the charts were averaged and the results plotted to form the accompanying curve. The record of each instrument is shown by its particular mark, the dot, circle, cross and square being used in addition there is plotted for each day a rectangular area representing 1 % CO2 in height. The proper positions of this area was determined by means of the Crsat. Where the plotted point for an instrument falls within the rectangel its accuracy is within 1/2% CO2, which is considered satisfactory. Where it falls outside the rectangle, inaccuracy is indicated."

Mar 1, 1925

By C. Travis Anderson

"A recent critical study by Ralston3 of the iron system points out the importance of and necessity for work upon the preparation of ferrous oxide. Not only are ferrous oxide samples desired for determination of the important physical and chemical properties, such as specific heats and heats of formation, bat also information on the stability and behavior of this material is of considerable technical importance. Related. problems where the properties of Fe0 are important have to do with desulphurization of iron, the formation and occurrence of magnetite in copper smelter slags, and sulphur elimination in copperFerrous oxide also has valuable catalytic properties, as is demonstrated in nitrogen fixation.Pure ferrous oxide has never been prepared in quantities large enough to furnish adequate physical and chemical data on its properties. Only two or three experiments4 have produced a fraction of a gram in a state approximating purity and have collected evidence that has been sufficient proof of their having done so. Ferrous oxide is stable only above about 570°C., and below that splits into magnetite and iron according to the reactionUp to about 1920, those who had endeavored to prepare FeO made no provision for rapid chilling, so that although their product. may have had the proper iron oxygen ratio for FeO, in reality it-probably did not consist of pure FeO. The above reaction is reversible; above 570oC. magnetite and iron are supposed to recombine almost completely, and if so, should constitute a direct and easy method of preparation. The data, however, were somewhat conflicting, and the extent to which the reaction goes in either direction needed checking. Preliminary experiments on the interaction of molten Fe304 with solid Fe gave Fe0 of about 85 per cent purity, corresponding to. the approximate purity obtained by some previous investigators. The present work is concerned chiefly with the results cf repeated interaction between partly reduced magnetite and iron, and the calculations which may be made from such results. Repeated treatments are necessary, because molten impure ferrous oxide and iron can not be kept in contact for more than short periods of time."

Oct 1, 1928

By F. W. Wood

Ingots of zirconium and other highly reactive metals such as titanium and hafnium produced by the consumable-electrode arc-melting process require conditioning before forging or rolling. A nondestructive, arc-conditioning technique has been developed as a substitute for lathe conditioning. The technique employs en electric arc under an inert atmosphere to fuse surface metal on the sidewalls of ingots without seriously affecting the general quality of the ingots. Advantages of the practice are Increased yields, lower accumulation of inferior scrap, and actual cost savings. The work cited in this report was done on zirconium. INTRODUCTION The consumable-electrode arc-melting process as practiced at the Bureau of Mines3 4/ has proved to be a technique for producing sound, homogeneous, commercial-size ingots of zirconium and its alloys. Ingots produced by this process, however, have as a characteristic a layer of partly fused metal on the sidewall to a depth of 3/16 to 3/8 inch. To prevent extension of surface imperfections during forging, the ingots are ordinarily conditioned by removing defective material in a lathe. If the metal were less reactive or the requirements less severe, the machine chips could be recycled and remelted. However, zirconium, being so oxygen sensitive, is contaminated by merely being machined despite extensive cooling of the tool bit. Further, being contaminated with oxygen, the chip metal upon remelting is 10 to 25 Brinell-hardnese numbers harder than the ingot from which it was machined. For this reason, the ingot specifications for naval reactor use have prohibited remelting machine chips, except as required for starting pads. Again, were zirconium less costly or less in demand this ever-increasing pile could be burned to oxide and recycled through the Kroll sponge process. Economics do not favor this, as melting feed stock has an estimated increase In value over oxide of about $8.80 per pound of contained zirconium. The efforts of the Bureau to solve the problem have been directed along two lines: To reduce the contamination of the machine chips produced and to reduce the quantity of the chips produced. This paper presents the technique developed to reduce the quantity of chips produced by arc-conditioning the remelted ingot.

Jan 1, 1955

By John J. Sammarco, Janet S. Flynt

This report (Independent Functional Safety Assessment Guidance 7.0) is the last in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and after-market suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 4, 2006

By John P. Harmon

A group of organic chemicals, known as wetting agents, has been developed, primarily for use in the textile industry. These chemicals have the property of reducing the surface tension of water when mixed with it in very dilute solutions. The advantage of lowered surface tension is recognized in dust-control work, and several wetting agents, have been tried by dust-control engineers with varying degrees of success. It is well-known that certain solids, coal for instance, are extremely hard to wet with plain water because of the high surface tension of water and the water-repellent action of coal. If the surface tension of the water is reduced, it can be demonstrated that the coal can be wetted easily. This is accomplished practical and at law cost by dissolving a very small percentage of wetting agent in the water that is to be used for wetting purposes. (Care should be exercised in using a wetting agent to be sure that it will not interfere with a subsequent process.) For some time, the comparative efficiency of various wetting agents has been the subject of considerable work by dust-control men at coal mines, as well as by members of the Bureau of Mines 3/, 4/, 5/, 6/. In this connection, a number of samples of air-borne dust have been collected in the mines. With the exception of dust-control measures conditions of dust generation and dissemination were maintained as, nearly uniform as possible. Samples were collected when water alone was sprayed on the cutter bar of a mining machine; various wetting agents were then successively added to the water and more samples of air-borne dust were-collected.

Jan 1, 1946

By Uwe Kaulbars

Vibration measurements at the workplace are often complicated and expensive. The assessment of the risk in conformity with EC Directive 2002/44/EC “Vibration” (which lays down the minimum requirements of laws in Europe for occupational safety and health) can therefore be carried out on the basis of an estimate based on information from manufacturers as well as by measurement conforming to ISO 5349. The characteristic values (emission values) determined by manufacturers in laboratory conditions may deviate from the exposure values measured at source at the workplace. Equally, deviations may arise as a result of the delay in the changeover of test methods from the single axis of measurement to the total vibration value for the three axes of measurement conforming to ISO 20643. To prevent faulty estimates, the manufacturer’s information has to be corrected by a tool-related factor in accordance with CEN/TR 15350. By taking the example of masonry and stone working machines, the empirically determined tool-related correction factor is checked and confirmed. Methods Vibration measurements were carried out in accordance with ISO 5349 in practical application conditions on 10 selected typical eccentric and orbital sanders, concrete and disc grinders as well as on wall chasers and stone saws. Results The total vibration value obtained for the investigated tools rangedfrom ahv = 3.6 m/s² to ahv = 11.6 m/s². When the values from the practical measurements are compared with the manufacturer’s vibration values, the underestimation of the risk occurring in some cases can be largely compensated for by the tool-related factors conforming to CEN/TR 15350 (see Figure 1).

Jan 6, 2006

By J. J. Bourquin, S. H. Katz

"Three types of respiratory apparatus namely, gas masks, hose masks, and self-contained oxygen-breathing apparatus - are now commonly used for protection from noxious gases, vapors, and smokes or ristes, but no particular type can be selected as best for all conditions. Many factors must be considered in connection with each situation, so that each must be considered as a problem in itself. Following are concise statements for comparing the types:Gas masks are the simplest and easiest to wear, also the least cumber-sore; but they protect only in comparatively low concentrations of noxious gases and should never be used where the air contains less than 16 per cent of oxygen. Special masks give protection from one gas or class of gases, but may give no protection against another gas or class of gases.Hose masks protect in any irrespirable atmosphere, but are somewhat cumbersome, the length of hose limiting the distance a wearer may go from fresh air. They are serviceable also where a supply of pure air moves with the wearer, as where a locomotive engineer in a smoky tunnel is using a hose mask supplied with air from the compressed air line of the locomotive. Hose masks consume no chemicals or materials and so are not limited in the time they may be used.Self-contained oxygen-breathing apparatus protect in any irrespirable atmosphere, but their weight is cumbersome, they can be used only by trained men, and frequent attention must be given them to maintain good working condition. On the other band they are the only safe means for exploring mines and other places filled with irrespirable gases in high concentrations."

Jun 1, 1923

By E. K. Kleespies

The Bureau of Mines determined the kinetics of the reaction of titanium-iron alloys with titanium trichloride dissolved in sodium chloride to provide a basis for understanding the reactions occurring in metallurgical processes involving reduction of the metal halides or alloy refining in fused salts. The rate of the heterogeneous reaction was determined between titanium-iron alloys and titanium trichloride to elucidate the effects of alloy composition on the rate. Measurements were made in an inert atmosphere with a high-temperature thermobalance using high-purity reactants. The rates of the reactions were about 1 x 10-5 g Ti/cm2-sec, and the reaction was phase-boundary controlled. Titanium alloys of the body-centered cubic beta structure reacted faster than those with the hexagonal close-packed alpha structure. The inter-metallic compound, TiFe, reacted very slowly, whereas TiFe2 was inert. Alloys containing above 89 atomic percent iron gained weight by reacting with titanium species in the salt solution and depositing titanium in the alloy. The effect of TiCl3 concentration on the reaction rate was determined from 2 to 12 weight-percent TiC13 and at various alloy compositions. At high iron contents, above 50 atomic percent, the TiC13 concentration effect was small. At lower iron contents, the TiC13 concentration effect was greater for beta-crystalline alloys than for alpha-crystalline alloys. The temperature dependence of the reaction between titanium alloy containing 8.7 atomic percent iron and titanium trichloride was measured over the temperature range 1,062° to 1,220° K, and the energy of activation was 7.7 kilocalories for the reaction.

Jan 1, 1967

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

A computer model of an existing mine ventilation system can be executed using data developed from ventilation survey results. This model can then be used to analyze and evaluate proposed modifications to the system. The acquisition of field measurements during a ventilation survey and the corresponding development of this information into computer input data have been discussed in detail in the preceding chapters. In this chapter, the data are used in computer-oriented analysis of the mine ventilation system. The PSU/MVS was selected for use because of its advanced capabilities. MINE DESCRIPTION The mine chosen for this application is located in Western Pennsylvania. The Pittsburgh coal seam, having an average height of 5-1/4 to 6-1/2 ft, is mined under approximately 300 to 500 ft of cover. The mine preparation plant and shipping facilities are located at the seam outcrop along a river; mining has progressed from the outcrop to an area about 10 miles from the pit mouth so that there are extensive worked-out areas through which access is maintained to the current mining area. Coal haulage is by conveyor to an underground transfer point, located four miles from the pit mouth, and then by high speed rail haulage to the preparation plant. The rail haulage link is scheduled for replacement by a conveyor in the near future. Mining at the present time is limited to the room and pillar method using continuous miners. Longwall mining had been attempted in the past with only limited success; as a result, several panels originally laid out for longwall mining are currently being extracted by room and pillar work. The

Jan 1, 1977

By A. L. Murray

"Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years, and in most mining towns of the state, both the operators and their employees deserve much credit for the efforts put forth to better the living, working, educational and recreational conditions. Progress has been and is being made, but there are still a few important towns where purer water and better sewage disposal are pressing needs.In the older metal-mining towns that are incorporated and are independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking toward improved welfare conditions than in company towns controlled by the mine operators.However, even in such towns the companies can do much to better welfare conditions, as shown by the progress in Bingham Canyon during the past several years. The Utah Copper Company has spent $800,000 since 1920, in the erection of modern brick cottages, apartment houses and the Germnell Memorial Club. The cottages and apartment houses have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club erected and equipped at a cost of $175,000 was provided by the company for the benefit of the Utah Copper employees living in the canyon and has been made the recreational center for the camp. Another improvement is the $100,000 fireproof hotel built by the United States Mine of the United States Mining, Smelting and Refining; Co. in the Copperfield section of Bingham Canyon. This hotel will accommodate 105 men exclusive of hotel help and has all the conveniences of a city hotel."

Sep 1, 1925

By R. H. Storch

This report describes work done as part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. The work included both field reconnaissance and a spot churn-drilling program. Much general information was available, as a result of earlier work done under the Western Radioactive Minerals Exploration Program conducted between 1950 and 1954 by the Bureau of Mines for the United States Atomic Energy Commission. This particular exploration provided data as to the quantity of ilmenite (TiFe03) and accessory black-sand mineral concentrates in a number of placer deposits; however, at that time no tests were made to ascertain if the ilmenite was of marketable grade. The spot churn drilling was begun in the Gold Fork area of Long Valley, Valley County, Idaho (fig. 1), in August 1956 and was completed during October of the same year. Eleven holes (designated as the GF series on fig. 2) 35 to 45 feet in depth, aggregating 425 feet, were completed during this period. Data from other exploration drilling in 1951 was used in this report. The 13 holes in the G series shown in figure 2 were drilled by the Bureau of Mines for the United States Atomic Energy Commission; the 7 holes of the DH series were drilled by the Bureau of Reclamation. The 20 holes, ranging from 16 to 140 feet in depth, totaled 1,625 feet. The combined number of all samples recovered was 422. Those taken in 1956 were composited for each drill hole and sent to the Bureau of Mines laboratory in Albany, Oreg., for analyses.

Jan 1, 1958

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 19,200-hectare Garfield Mountain study area in east central Idaho. The area had been proposed for Wilderness. Cretaceous-age quartzite and limestone conglomerates underlie the area&apos;s east half; thick travertine beds, as well as limestones, dolomites, sandstones, and volcanic tuffs occupy the west half. All the rocks have been faulted and folded as part of the Western Overthrust Belt. Two, enormous travertine deposits occur in the west end of the study area. The lower deposit, controlled by Faxe Kalk Inc., has at least 200 million m3 (cubic meters) of travertine resources. Most of their deposit is very bright with a high CaC03 content and a low insoluble residual percentage: thus it is suitable for use as a paper and paint filler. The upper deposit, owned by Idaho Travertine Corp., contains 100 million m3 of travertine resources; it is used for facing or dimension stone. Weathered travertine outcrops are buff to tan and locally vuggy. Bureau of Mines samples of&apos; outcrops contained greater than 95% CaC03. Approximately 600 m3 of travertine have been quarried from the two deposits and used for facing stone. Four travertine quarries and two dozer cuts were examined. Faxe Kalk has 103 White Rock placer claims on the lower deposit; approximately one-half of the claims are within the study area. Idaho Travertine has the Limestone 1 and 2 placer claims on the upper deposit. A 4,647-m-deep oil and gas exploratory well was drilled on the east end of the study area without success.

Jan 1, 1993

By Joan C. Biordi

In this research by the Bureau of Mines, slightly lean CH4-O2-Ar flames at 0.042 atm with and without small amounts of the inhibitor CF3Br were probed using molecular beam and mass spectrometric techniques. Ratios of product concentrations to reactant concentrations were formed and compared with the equilibrium constant for seven reactions--(l) H+O2 = OH+O, (2) O+H2 = OH+H, (3) OH+H2 = H2O+H, (4) OH+OH = H2O+O, (5) CO+OH = CO2+H, (6) Br+HBr = Br2+H, and (7) H+HBr =H2+Br--to determine to what extent they may be considered balanced in various regions of the flame. With the possible exception of reaction 4, none of the reactions are completely balanced until maximum flame temperature is reached. Once the reactions become equilibrated, their balance is maintained as the temperature and radical concentrations falloff in the secondary reaction zone. Reaction 7, in inhibited flames, is balanced at relatively low temperatures, comparable to reaction 4. Reaction 6 was found not to balance in either the secondary or primary reaction zones. Radical decay in the secondary reaction zone was analyzed using the pool-decay concept. The important recombination reactions were judged to be H+OH+M~H2O+M, and H+O2+M?HO2+M. A rate coefficient of 2x1016 cm6 mole-2 sec-1 is calculated for M = the burnt gas mixture of Ar, HaO, CO2, and 5x1015 cm6 mole-a sec-1 is calculated for M = Ar (both for T = 1,750±150 K).

Jan 1, 1977

By Berenice B. Mitchell

THE STATISTICAL tables in this chapter present, country by country, the mineral production of the world in 1949-50. The figures are on a mine basis, unless otherwise indicated, except for cement, coke, and steel, which are measured at the processing plant. The tables are essentially a retabulation, by countries, of the 53 commodity world tables appearing in the various chapters of this volume. For lack of comprehensive information, data for the following minerals are excluded: Andalusite, aplite, asphalt, boron, bromine, calcite (optical), calcium chloride (natural), carbon dioxide, clay, columbium (niobium), diatomite (kieselguhr), dumortierite, emery, garnet (abrasive), gem stones (other than diamonds), germanium, greensand, grindstones, helium, indium, iodine, kyanite, lithium, magnesium compounds (other than magnesite), meerschaum, mineral pigments, monazite, natural gas, natural gasoline, oil shale, olivine, perlite, pumice, quartz crystal, radium, sand and gravel, selenium, sillimanite, sodium salts (other than common salt), stone, strontium, sulfur (byproduct), tantalum, tellurium, thallium, topaz (industrial), tripoli) uranium, vermiculite, wollastonite, and zirconium. In addition, a few minor geographic areas for which no statistics are available, are also omitted from the tabulation; it is believed that no significant quantities of minerals are mined in any of these areas. The statistics in these tables were derived principally from questionnaires sent, in cooperation with the United States Department of State, to the governments of each country. Supplementary sources were United States consular reports, the Imperial Institute&apos;s Statistical Summary of the Mineral Industry of the British Commonwealth and Foreign Countries, other official publications of various countries, the United Nations Statistical Yearbook, the Year Book of the American Bureau of Metal Statistics, Minerais et Metaux, business magazines, and company reports. Where official data were not available, esti-

Jan 1, 1953

By Manuel Gomez

Areal distributions for ash, total sulfur, and sulfur forms were developed for the top 12 inches, the middle section, the bottom 8 inches, and the total seam of Pittsburgh coal in southwestern Pennsylvania. The sulfur and ash exhibit an apparent high local variability. As a general rule, both the sulfur and ash show high concentrations in the top 12 inches and in the bottom 8 inches of the seam relative to the concentrations observed in the middle section of the seam. The high-low sulfur and ash concentrations in the top 12 inches of the seam are not coincident with the high-low sulfur and ash concentrations in either the middle section or the bottom 8 inches of the seam. With respect to sulfur and ash, it is suggested that the top and bottom sections of the Pittsburgh coal may reflect both a syngenetic and epigenetic origin. Present data support the belief that paleotopography controlled Pittsburgh seam deposition. Evidence is presented to show that channels were cut at various times into the semilithified sediments that buried the Pittsburgh seam. In this channeling process, portions of the Pittsburgh coal may have been eroded away. Following channel development, the lower part of the Pittsburgh sandstone filled the complex system of braided channels to produce the "want areas" encountered in present mining operations. In localized areas of the Pittsburgh seam, impingement of Pittsburgh sandstone may be responsible for the lateral displacement of the coal. Information of this type becomes important in the assessment of exploration data, in the development of a quality control system for mine output, and in mine life planning.

Jan 1, 1974

By C. A. Herbert

"Haulage accidents usually are responsible for about 17 or 18 percent of all coal-mine fatalities and about 21 percent of all non-fatal coal-mine accidents. When the relatively small number of employees continuously exposed to haulage hazards is considered, it would appear that haulage is more hazardous than any other phase of coal-mine operation.Haulage accidents have increased from year to year, doubtless due to the increase in electrical haulage, and particularly to the use of larger cars, heavier locomotives, longer hauls, and greater speed. Unless very definite steps are taken to eliminate the causes of these accidents, they will continue to increase rather than be reduced, as they can and should be.Underground haulage in many of the large modern mines of today is similar in many respects to railroad practice. In recent years the railroads have made wonderful strides in reducing accidents, and instead. of being one of the most hazardous occupations, as it once was, railroading is now one of the safest. Doubtless, if thought and action, similar to that given to reducing accidents among railroad passengers and employees, were given to safety in mine haulage, under¬ground haulage accidents could be reduced in about the same ratio.Haulage accidents may be classified, according to responsibility, into two groups - those for which management is largely responsible and those for which the employee is largely to blame; there is, however, an overlapping of responsibility from one group to the other. If, therefore, haulage accidents are to be reduced, it is absolutely essential that both management and employees cooperate to this end.In the first group, for which management is largely responsible, may be included accidents due to faulty equipment, moor track, a poorly arranged system of haulage, lack of clearance or of overhead protection, and dirty roadways; even in these features, however, the employee is not without a measure of responsibility, as failure of haulage equipment possibly may be due to lack of care on his part, failure to report when equipment is out of order, or failure to do a good workmanlike job of installing or repairing or operating.To the second group of accidents for which the employee may be largely responsible, belong those caused by such careless practices as jumping on and off fast-moving trips, coupling on the ""fly"", running at excessive speeds, failure to properly block cars, and similar hazardous and unnecessary acts of omission or commission. If, however, management condones such practices, or, as in some instances, insists upon them, it must accept its share of responsibility for the accidents that inevitably result.Some of the most prolific sources of haulage accidents will be discussed briefly, together with the steps that may be taken to minimize their occurrence."

Oct 1, 1939

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of ventilation on the water spray patterns of automatic sprinkler heads. Experiments were performed in a rectangular tunnel with pendent, upright, pendent sidewall, and horizontal sidewall sprinkler heads at air velocities of 0, 150, 300, 500, and 800 ft/min. As the air velocities were increased, there were significant shifts in the total coverage areas, density distribution patterns, and the maximum coverage densities for all types of heads. The pendent and upright heads exhibited upstream shifts in total coverage in the direction of the air-flow ranging from 4 to 6 ft, while the downstream coverage distances were extended up to 14 ft at the 800 ft/min airflow. The shift in upstream coverage distance for the sidewall heads ranged from 6 to 12 ft, while the downstream coverage was extended up to 22 ft at 800 ft/min. The results showed that airflow can have a significant effect on the coverage characteristics of automatic sprinkler heads and needs to be considered in the design of effective sprinkler fire suppression systems for ventilated areas.

Jan 1, 2010

By Clyde M. Pearce

The Lake Superior iron-mining district includes parts of the States of Michigan, Minnesota, and Wisconsin. The laws of each State provide for an industrial commission and for inspection of mines. The following extract from the General Orders on Mines, effective October 25, 1937, issued by the Industrial Commission of Wisconsin, is the only reference to the use of safety catches on mine cages or skips found in the laws and regulations in the Lake Superior iron-mining district: Order 316 - Cages for Hoisting Men. (c) Sides, Gates, and Safety Catches. ***Every cage shall be provided with safety catches of sufficient strength to hold the cage with its maximum load at any point in the event the hoisting cable should break. (d) Testing Safety Catches. The safety catches of cages and skips used to hoist men shall be kept well oiled and in good working order. They shall be tested at least once each month by tying up the cage or skip with hemp rope, lowering a few feet of hoisting cable on top of cage, then cutting the hemp rope, provided that any other system of testing, which is equally effective, may be used.

Jan 1, 1945

By G. C. Reed, J. A. Herdlick

The Blackbird district, Lemhi County, Idaho, has long been recognized as a potential source of cobalt and copper. Exploration of the early discoveries in the area was largely discouraged by the comparatively low grade and small size of the known ore bodies, the slight demand for cobalt, and the lack of adequate roads throughout the region. Recent advances in the field of alloy metallurgy culminated in a steadily expanding demand for cobalt. This demand was finally accentuated to critical proportions in 1940 by worldwide rearmament programs and by the threatened disruption of foreign imports by submarine warfare.

Feb 1, 1947

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Center are developing ways to protect the health of miners. Part of that effort is improving the air quality in metal/nonmetal mines by developing proper ventilation techniques. The air quality of large opening nonmetal mines can be greatly improved by using engineering controls of contaminant prevention and proper ventilation techniques. Contaminant prevention includes methods to reduce contaminants from entering the mine air. Ventilation can be improved with appropriate fan selection and fan operation used in conjunction with air coursing using manmade and insitu rock stoppings.