Search Documents

By C. B. Manula, R. L. Sanford, R. A. Rivell

A central requirement for using simulation models is the need for retrospect testing to validate experimental conclusions. Acceptance of a model by managers and safety practitioners is more likely to depend on its tested performance in-the field rather than on the underlying logic or the validity aspects of the model itself. It is here that simulation bridges the gap between theory and useful design procedures. The original version of the rail haulage sub-assembly was success¬fully tested in the field (Sanford, 1969). However, the case studies that were described here involved single-stage haulage and restricted jobtypes from UGMHS. Since this report together with Volume VI (Production Subsystem) describes extensive changes and modifications to the rail haulage sub-assembly and UGMHS, field tests were necessary to verify both the rail model and the linking concepts to the Produc¬tion Sub-system. Mine Description The candidate mine selected for model verification works the 6 1/2 foot Pittsburgh seam. Shaft openings are used for manways and ventilation and a dual compartment slope for materials handling. In the bottom half of the slope, a hoist with track handles supplies and equipment. In the upper half, a 42 inch belt conveyor travelling at 450 fpm moves coal from a rotary dump to the surface. The immediate roof is shale with the first 12 inches taken during development mining. About 4500 raw tons are produced daily from seven face units and one spare working three shifts. At seven of the sections,

Jan 1, 1974

By Hon-Chung Ko

This Bureau of Mines report provides the enthalpies of formation of cupric bromide and cuprous bromide as determined by hydrochloric and hydro-bromic acid solution calorimetry. At 298.15 K, the values are -33.10 ± 0.4 kcal/mole for CuBr2, and -25.24 ± 0.25 kcal/mole for CuBr.

Jan 1, 1975

By N. F. LeJeune

For a number of years the Bureau of mines has conducted semi-annual surveys to determine the changes in the characteristics of the motor gasoline being sold in the United States. The Bureau of Mines surveys, from April, 1917, to January, 1943, indicated a progressive decrease in the end point range. The survey for July, 1923 showed an interruption in this progressive decrease. This interruption, as shown in Table 1, in the line marked "Difference," was apparently a definite one, for the data obtained in the surveys of July, 19233, January, 19244, and the present one, apparently substantiate it. The figures in Table 1 were obtained by averaging the end points of the least volatile and most volatile samples of gasoline. For example, of 850 samples analyzed in 1919, the 10 per cent (85 samples) having the highest end points and the 10 per cent having the lowest end points were grouped, and the end points of each group averaged. These averages are represented in the table as the "Maximum 10 per cent" and the ?Maximum 10 per cent," respectively. The same scheme was used on the succeeding surveys.

Jan 1, 1924

By Jr. Herty

Ferromanganese continues to be an indispensable requirement in steel manufacture. Approximately 470,000 of the 80 per cent ferro-alloy was consumed in 1929 and increasing amounts will be required annually by the steel industry unless some satisfactory substitute is found. An average of 14 pounds of metallic manganese is used for each ton of steel produced, The principal use of manganese is for de-oxidation of the metal in the steel refining processes, although a considerable amount is also used for the production of special manganese steels. Unfortunately, domestic production of manganese ore is inadequate to meet normal peace-time requirements, not to mention increased abnormal war-time demands. The rather large quantities of low-grade manganiferous iron ores which occur in the Coruna Range in Minnesota have for a number of years greatly appealed to those interested in the development of a domestic source of the supply. The North Central Experiment station of the Bureau of Mines has made an elaborate study of the possibilities of the pyrometallurgical treatment of ores from these deposits and much of the valuable information secured by them has already been published.

Jan 1, 1930

By G. B. Shea

The accident experience of the California petroleum industry for 1927 was characterized by a decrease it .the number of fatalities. The year closed with a total of 41 fatal accidents, as compared with a total of 54 for the preceding year. 3 In percentage, the figure for 1927 represents a decrease of 24 per cent from that of 1926 and evidences the promising results of organized safety work, in which the industry in California has taken an absorbing interest. The percentage of decrease for 1927 is the largest recorded in any one year since the compilation of the fatality record in the California petroleum industry was begun. Although good progress has been made during the past few years, much remains to be done to reduce still further the human and economic waste caused by accidents. This review is intended to show the employee, as well as the employer, the proximate and contributing cause of accidents. To increase the value of the report, preventive measures in various instances are suggested, on the theory that accidents of a similar nature will occur unless remedial action in taken to remove the cause.

Jan 1, 1928

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

Because of the high number of accidental methane gas ignitions in metal and nonmetal mines, the Bureau of Mines searched for a simple guideline that would allow mine personnel to evaluate the methane hazard in a given mine. Air samples were collected by the Bureau in 53 metal and nonmetal mines and analyzed for trace evidence of methane gas. Samples were collected in the returns and at the working faces. Those mines classified as gassy by the Mine Safety and Health Administration had a significantly higher average methane concentration than those classified as nongassy. Of the 9 gassy mines sampled, 7 had methane concentrations above 100 ppm, whereas only 1 of the 44 nongassy mines had a concentration above 100 ppm. The 100-ppm concentration may be used as a simple and convenient guideline for forecasting the methane hazard in a mine, whether or not the mine is classified as gassy. There was no consistent correlation between commodity mined and methane concentration, nor was there a correlation between mine depth and methane concentration. Neither of these factors can be considered a guideline for predicting methane hazards.

Jan 1, 1979

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982

By Jürgen F. PH. D. Brune, Alex C. Smith, Michael A. Trevits

Underground coal mine fires in the United States continue to present a significant hazard to the safety and health of mine workers. The leading causes of mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion The National Institute for Occupational Safety and Health (NIOSH) is conducting an in-depth program of research to address mine fire prevention, early and reliable fire detection and mine fire suppression and control technologies. One segment of the research portfolio is focused on remote methods for addressing coal mine fires. This research is important because remote methods represent the primary means of fighting a mine fire when conditions are too dangerous to fight the fire directly underground. Technologies under investigation include remote methods for installing ventilation control devices (mine fire seals) and remote methods for suppressing the fire using, the injection of inert gas, gas-enhanced foam and jet engine exhaust gases into the fire zone. This paper presents a summary of remote mine firefighting technologies used in the U.S. and the results of completed NIOSH research.

By Charles D. Martens

Raw non fuel minerals produced in the United States during 1981 had an estimated value of $25 billion, about the same as that of 1980. In terms of 1980 dollars. the value of minerals produced during 1981 was $23 billion.2 This chapter includes tables for 1980 that were not available for publication in the 1980 Minerals Yearbook, but does not include the corresponding tables for 1981. The underlying causes of the overall decline in U.S. nonfuel mine production during 1981 were varied, but the common factor was the worldwide recession. In some cases the decline was traced to foreign competition. For example, iron ore production was lower in part because of increased imports of steel products such as coiled steel sheet. Another problem experienced by the domestic mining industry was the continuing difficulty in attracting capital. This was due in part to the attractiveness of investments outside the mining industry, such as short-term, high-interest securities. Another reason was the importation of commodities from countries where overall costs were lower because of such factors as high ore grade, lower taxes, lower wages, government subsidies, and less stringent safety and environmental regulations.

Jan 1, 1982

By Steven J. Schatzel, Joseph Cervik, Gerald L. Finfinger

Gas drainage through surface bore¬holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwal..ls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole inter¬cepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain¬age during longwall mining will be essen¬tial for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European tech¬niques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By K. R. Farley

A simplified method for the atomic absorption determination of antimony is described. Samples are dissolved in hydrobromic acid and diluted to volume with water. Solutions can be ready for analysis in about 10 minutes and are stable for at least 24 hours. The spectral line at 231 nanometers is used, and there is no effect on absorption resulting .from the presence of any concentration of HBr. Absorbance is linear with antimony concentrations up to 120 micrograms per milliliter. Sensitivity is 1.48 micrograms per milliliter per 0.0044 absorbance. Relative errors on National Bureau of Standards Standard Reference Materials were 3 percent or less, and relative standard deviations on 12 determinations of each of three flue dust samples were 4 percent or less (95-percent confidence limit).

Jan 1, 1980

By M. J. Ferrante

Relative enthalpies of V20S from 298.15 to 1,101.0 K were measured at the Bureau of Mines to provide data needed for the advancement of min-eral technology. Enthalpies were measured with a copper-block calorimeter. A sharp melting point was found at 951 K, with [~~ = 15.690 kcal/ mol ] for the standard enthalpy of melting. Tabulated values are given at selected temperature increments between 298.15 and 1,500 K for the standard relative enthalpy [(HO -H~98),] heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)/T]. Standard relative enthal-pies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1986

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

Appendix B - Mine Evacuation Simulation Program - User's Manual B 1 Introduction Appendix B documents information necessary to use the emergency escape simulation program and to make modifications if necessary. For a user interested in using the program as it exists, Sections B 2, B 5 and B 6 are particularly useful. The program listing (B.6) can be used to prepare a card deck and the data cards can be punched from the directions given in Section B. 2. Typical input data and output printout summarized in B 5 provides guidelines for the program use. Sections B 3 (Program Nomenclature) and B 4 (Subroutine Description) describe, in detail, the inner workings of the program and are particularly useful for a user interested in modifying the program.

Jan 1, 1976

By W. E. Caspar, W. L. Eaton, W. M. Rohmiser, James Westfield, E. J. Podobrski, L. H. Johnson, S. H. Ash

A flood in mine workings is a crisis even if no lives are lost, and when the crisis is past and the excitement wanes there is usually a rapid return to unwarranted complacency in those regions where floods occur, even though the danger of imminent recurrence is known. Experience in flood control, regardless of its nature, has taught that in a flood the work does not cease when the emergency passes; rather, it increases as the water recedes. To do nothing, when it is known that a hazard exists, is inexcusable for those that should do something. To prevent floods in mines, data should be collected and something constructive done with those data, not alone for present conditions but for the future.

Aug 1, 1947

By Rimas Pakalnis, Catherine A. Dreesbach, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash's trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 micro strain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

Jan 10, 2000

By Garrett R. Hyde

Sintered yttria and sintered dysprosia can be used to make single-component thermistors having typical thermistor geometries and operable in the temperature range 500° to 1,200° C. However, at these temperatures, instability of platinum electrodes can contribute a slight aging effect if the thermistor is kept near 1,200° C for long periods. Typical characteristics at 500° C for an yttria disk thermistor 12 mm in diameter and 2 mm thick are a resistance of 12.4 megohms and a temperature coefficient of resistance of -3.8 percent per degree C. Typical characteristics at 500° C for a dysprosia thermistor of the same dimensions are a resistance of 1.84 kohms and a temperature coefficient of resistance of -1.6 percent per degree C.

Jan 1, 1970

By R. Pakalnis, C. A. Dreesbach, L. A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash’s trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 microstrain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

By John R. Benham

The Long Swamp RARE II area contains no prospects, claims, or mines. It has a low potential for ore deposits. There are no geothermal, oil, or gas leases in the area. APPRAISAL There are no mining districts in the study area. The nearest is Chewack Mining District, which is 6 mi (9.6 km) north of the area. This district had numerous claims located for tungsten; the principal tungsten ore mineral was wolframite. Wolframite was found here in 1898 by surveyors of the International Boundary Commission. The area was staked in 1908 and developed during 1915 and 1916. Only in 1936 was ore shipped; the 30 ton (27.2 t) shipment proved to be unprofitable for the claimants (Culver, 1945, p. 41).

Jan 1, 1982

By E. Morrice

Techniques developed by the Bureau of Mines for the preparation of high-purity rare-earth metals and their alloys by electrolysis of the oxides in fluoride media are summarized. Cerium, lanthanum, neodymium, praseodymium, dysprosium, gadolinium, and yttrium metals, the mixture didymium, and specific alloys of these metals and samarium with iron, nickel, chromium, and cobalt were prepared. Individual metals were electrodeposited in the liquid state on tungsten or molybdenum cathodes. Alloys were prepared by electrodepositing the rare-earth metal on a consumable cathode, at a temperature above the melting point of the eutectic formed between the rare-earth element and the cathode material. Cells were designed for electrowinning metal products in gram and pound quantities, and methods for continuous electrowinning of cerium and lanthanum were developed.

Jan 1, 1968

By J. Roger Loebenstein

Demand for arsenic exceeded supply, and major domestic and foreign producers allocated available supplies to customers for the fourth consecutive year. Major demand for arsenic was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-Effective April 1, 1981, taxes were collected from companies producing and importing 42 chemicals and petroleum products designated as hazardous, The revenue was used to begin funding of the 5-year, $1.6 billion "superfund" being established under Public Law 96-510, the Comprehensive Environmental Response, Compensation, and Liability Act, designed to help clean up spills of hazardous substances throughout the United States. As hazardous chemicals, arsenic metal and arsenic trioxide were taxed at the rate of $4.45 and $3.41 per short ton, respectively.

Jan 1, 1982