Search Documents

By R. B. Corbett

"INTRODUCTION Aluminum and manganese bronzes as a group, may be separated readily from other copper-base alloys by experienced sorters. However, separation of aluminum bronze from manganese bronze is generally a matter of guesswork, so that accurate separation presents a difficult salvage problem.Attempts at separation by the thermoelectric tester. 3/ which had proved successful in solving other sorting problems, showed in this instance that the desired separation was uncertain because of the wide range of composition allowable in each kind of bronze. If only one composition of each kind of bronze were used in industry, separation by the thermoelectric method probably would be simple. However; the variability in composition observed in commercial alloys is so great that the thermoelectric power of the one type frequently overlaps the range of values found for the other. As a result, specimens frequently are classified in the' wrong group.Separation of the two types of bronzes on the basis of measurements of magnetic properties on filings from the various samples also proved unsuccessful because the test results overlapped to such an extent that no clear-cut division could be obtained.Electrode potential measurements were made also on the aluminum and manganese bronzes in the hope of distinguishing between them. A drop of saturated potassium chloride solution was placed on the fresh surface of the metal and the tip of a calomel electrode introduced therein. The voltage generated was measured by connecting the electrode and the bronze part to a research-type potentiometer. Although the voltages generated by the manganese bronze parts were greater than those generated by the aluminum parts, the difference in the closest two sets of readings was not sufficient to warrant a good separation. When a concentrated potassium alum solution was used instead of the potassium chloride solution, a wider divergence of voltage was produced by the various bronzes, but unfortunately readings overlapped in several instances."

Nov 1, 1944

By Stuart R. Zimmerley, John Gross

"In the study of ball-mill grinding at the Intermountain Experiment Station of the United States Bureau of Mines at Salt Lake City, Utah, it was desirable to measure the work input to a ball mill at the mill itself so that consideration of motor efficiency and transmission losses would be eliminated.The device adopted is essentially that used by Prof. H. E. T. Haultain4 in measuring work input to rolls. The mechanism was changed only so as to adapt it to a ball mill.Figure 1 is a diagrammatic sketch of the apparatus.The pulley which rotates the mill is loose on the mill shaft and is equipped with ball bearings. This pulley is connected by means of three tangential springs to the driving plate, which is solid on the mill shaft. Power applied to the loose pulley is transmitted to the driving plate, and hence to the mill, by the three springs; the greater the resistance of the mill, the greater the spring extension. The extension of the springs is transmitted by the steel extension tape to the differential integrating meter.The integrating meter is operated by two friction wheels in contact with the integrator disk which revolves at a definite ratio of speed to that of the mill. The friction wheels are held in contact with the disk by the spring suspension of the integrator and are connected to a differential gear cage, the revolutions of which are recorded on a counter such as is used in gas meters. Due to the differential gears the c e is stationary when the two friction wheels revolve at the same speed in opposite directions; this condition exists when the integrator is centered on the disk and corresponds to no load or to a zero spring extension. As the lead is applied, the springs extend and move the integrator from the center or zero point, resulting in a difference of speed between the two friction wheels. Due to the revolution of the differential cage this change in. speed is transmitted to the counter. The integrator and extension tape system is kept taut by means of a light spring attached to the integrator, the spring having just enough tension to assure that the integrator returns to zero when the load becomes zero."

Feb 1, 1931

By Charles Vaught

This paper discusses the fact that US coal mining organisations are losing the knowledge they need in order to be able to respond to emergencies. The authors note that knowledge management provides a useful perspective from which to view the problem, but that the debate about what constitutes knowledge should be broadened to include a debate about what constitutes management. It is argued here that knowledge is actually shared knowing distributed across group members; that such knowledge can be managed by cultivating it; and that narrative is the medium through which this may be done. The paper then examines NIOSH research that has attempted to use such an alternative knowledge management approach to help potential mine emergency responders better deal with the predicaments they are likely to encounter on-site.

Jan 1, 2006

By M. D. Schlesinger

Mercury exists in coal in minute quantities, but the large tonnages of coal consumed could represent relatively large amounts of mercury entering the environment. Limits have now been placed on the emission of mercury, and it is important that reliable analytical methods be available to the chemist. The Bureau of Mines has evaluated analytical techniques used by a number of laboratories; most used vapor phase atomic absorption as the final detection method. Neutron activation was used by some of the laboratories. All of the methods described could be applied, but they require careful manipulation to prevent loss or mercury contamination. In the samples analyzed the mercury content ranged between 0.05±0.01 and 0.4l±0.06 part per million.

Jan 1, 1972

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

By Jerry W. Stengel

The Bureau of Mines subjected two manufacturers' chemical oxygen (K02) self-rescue breathing apparatus to a series of laboratory environmental treatments designed to simulate various conditions in underground coal mines. The environmental treatments consisted of extremes of temperature, shock, and vibration. The tests were designed to be used as predictors of the ability of the self-rescuers to survive those environmental insults with no degradation in their protection to the wearer. Based on the severity of the treatments, simulating conditions more severe than offered by the mining environment, the two apparatus tested should be able to withstand the abuse offered by the mining environment and still function as intended in an emergency. Correlation of these tests with results of long-term field evaluations is needed to provide confidence in the laboratory tests as predictors.

Jan 1, 1982

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

By Joan T. May

Anhydrous methods were tested for the extraction of beryllium from low-grade source materials. The purpose of the investigations was to find new extraction processes that are applicable to domestic ores. Beryl, helvite, and phenacite materials containing from 0.1 to 2.8 percent BeO were used as starting materials for direct halogenation tests and pretreatment followed by halogenation. The results of the investigations showed that direct fluorination and carbide-chlorination are two practicable methods that can be applied to low-grade concentrates. Treatment of concentrate-carbon mixtures with anhydrous hydrogen fluoride extracted 99 percent of the beryllium in the concentrate; the soluble fluoride product, converted to an oxide, contained 70 percent BeO. Chlorination of beryllium-silicon carbide, prepared from low-grade concentrates, extracted beryllium into the volatile chloride product.

Jan 1, 1962

By Allen D. Look, J. Howard Bird

"INTRODUCTION The Phelps-Dodge Corp. New Cornelia Branch open-pit copper mine operated without a fatality in the drilling and blasting department from December 13, 1937, to April 1, 1947, and continuing.Between the dates named the explosives crews had a total of 746,520 man-hours of exposure and handled 12,000 tons of explosives, over 770,000 detonators, 2,300,000 feet of fuse, and 7,700,000 feet of Primacord in loading holes to break 116,780,000 tons of material.It is the purpose of this paper to record the procautions taken to insure safe handling of explosives at this operation where safety is definitely a matter of forethought rather than chance.GENERAL INFORMATIONThe New Cornelia Branch open-pit mine operates on a large, low-grade, disseminated-copper deposit about one-half mile south of Ajo, Ariz. The pit is approximately oval; the ore body being some 4,800 feet long and 2,750 feet wide. Ore is mined with electric shovels loading into railroad cars. All benches in- the pit are 40 feet in height except two, which are 60 feet high.The New Cornelia ore body differs from most porphyry-copper deposits in being hard and siliceous. In common with the other low-grade porphyry-copper deposits, continued operation is possible only with economical handling of large tonnages. This has necessitated a great deal of study in the evolution of a safe and efficient method of handling the large quantities of explosives needed in breaking this hard-rock material."

Feb 1, 1948

1. Mining to prevent and control underground acid formation should begin with education imparted through: (A) Course work at mining schools to teach prospective engineers. (B) Training of engineers presently employed in the mining industry through appropriate mining extension courses. 2. Considerable need exists to devote more attention to: (A) Hydrogeologic studies of mining areas to enhance the planning of new mines and the abatement program of existing mines. (B) Additional research to explore methods of dewatering the strata associated with mining areas. (C) Further effort to develop sealants for preventing contact between water or oxygen and the acid producing material associated with the coal seam.

Jan 1, 1970

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974

By Edward A. Barrett, Lynn L. Rethi

Recent studies have shown that miners performing construction, maintenance, and repair (CMR) work activities in the conduct of their jobs incur from 39 to 65 percent of all reported injuries in the mining industry, The number is particularly high at surface aggregate operations; however, the problem exists at all mining locations and commodities. To address this issue, an interactive, (3-D) slides training exercise, Hazard Recognition Training Program for Construction. Maintenance and Repair Activities, was developed. The purpose of the exercise is to teach work& to recognize CMR hazards in the workplace and to deal with them using accepted safe work procedures. It was field tested using a total of 340 persons from surface mining operations in six states. The subjects were tested before and after the training intervention to determine if objectives of the instruction were achieved. Results indicated that 7 1 percent of the participants showed improvement in ink test scores. Following the posttest, subjects responded to a seven question Likert scale. These questions related to the validity of the exercise and the utility of the training program. More than 93 percent of the miners reported that they "learned something new from the training" and over 94% said they "would use these practices to work more safely".

By Todd M. Ruff

A training software package for new mine employees, called Miner Training Simulator (MTS), has been developed by researchers at the National Institute for Occupational Safety and Health. MTS is a computer-based tool that allows a trainee to enter a simulated mine and interact with his/her surroundings in order to learn basic mining concepts, safety procedures, mine layouts, and escape routes. The training simulator software and instructions for its use are described in this report. Also, each mine using the software will have different requirements with regard to safety training. To customize the simulator for these differences, an interpreted scripting language is used to define interactions between the trainee and the virtual mine and objects in it. The scripting language, called Tool Command Language, uses simple commands to control various actions in the simulation, such as sounds, safety messages, hazards, and movement of objects. The basics of the scripting language are described here, along with many examples and instructions for building a script for MTS.

Jan 6, 2001

By A. Adams

The Bureau of Mines determined the composition of the vapors liberated during thermal decomposition of aluminium nitrate nonahydrate. Small samples were heated from room temperature to 5500 C with initial heating rates from 500 to 2000 C/min. Gases were rapidly swept away from the heated chamber with Ar and subjected to immediate analysis in order to minimize reaction between the components. In addition to H20, four N-containing compounds were identified: HN03, N02, NO, and N20. Nz could not be determined in the presence of the nitrogen oxides, and at-tempted separation from the oxides led to the formation of more nitrogen. Relative amounts of each component were found to vary over a period of time; however, total amounts measured with different heating rates were reasonably constant and were typically as follows: 84.2 pct HN03, 7.1 pct N02, 4.3 pct NO, and 4.2 pct N20. HN03 and NO were determined from chemical reactions with a permanganate solution, N20 was measured with a mass spectrometer, and NO2 was measured with a spectro-photometer. Details of the methods used are described. Since NO2 and NO can readily be converted to HN03, about 96 pct of the N from the decomposition can be recovered as HN03

Jan 1, 1987

By M. E. Kundick, W. E. Dieter, L. Cohen

The major details of design and maintenance of a seamless stainless steel fume hood system , developed by the Bureau of Mines , are described and illustrated . Operating and housekeeping routines are outlined .

Jan 1, 1964

By C. Melvin Lepper

A solid-state amplifier for the bridge circuit of an atomic-absorption mercury detector is presented and described. Operational advantages over previously used circuitry include improved time and temperature stability, increased measurement accuracy, and simplified setup, calibration, and operation.

Jan 1, 1972

By Joseph Grumer

In addition to nine powder and gaseous extinguishants of propagating Pittsburgh seam coal dust-air explosions earlier evaluated,6 10 other powders have similarly been evaluated under like conditions such that wall quenching of the coal dust-air flames was virtually absent and the dust concentration was temporally and spatially uniform to within about ±5 percent. None of the newly examined extinguishants was better than Purple-K (potassium bicarbonate); the 10 of this report are anhydrite (calcium sulfate), monobasic (4 types) and dibasic ammonium phosphate, natural and synthetic cryolite (sodium fluoalumi-nate), sodium sulfate, and tricalcium phosphate. Except for anhydrite, sodium sulfate, tricalcium phosphate, and the cryolites, these materials were about equally effective, when present in relatively low concentrations (weight-percent of the coal dust-extinguishant mixture). The maximum oxygen concentration for the extinguishment of otherwise uninhibited coal dust explosions and the influence of coal dust particle size and the volatile content of the coal were also explored. For the present, the choice of the inhibitor among the good ones evaluated is not as critical as the system to be used to deploy the extinguishant against a coal dust explosion.

Jan 1, 1973

By Richard J. Mainiero, Harry C. Verakis

The Bureau of Mines has conducted research to determine whether the total elapsed delay time for blasting bituminous coal in underground mines could be safely expanded beyond the present 500-ms limitation without igniting a methane or methane-coal dust atmosphere. The results indicated that the increase of total delay from 500 to 1,000 ms had no detectable effect on safety relative to incendivity as long as permissible practices were observed in all other aspects. Research was also conducted to evaluate the safety of 18-in hole spacing for delay blasting in coal relative to misfires. For a variety of permissible explosives, misfires were observed for about 50 pct of the holes at 18-in spacing. Based on this observation, the Bureau has recommended that the new regulations prohibit hole spacings of less than 24 inches in underground coal mines. Misfires were also observed for 24-in spacing, but the number of misfires and test shots was too small to sup- port any firm conclusions.

By E. J. Kloos

The Bureau of Mines developed a test for evaluating gas masks designed to protect against phosphine gas; phosphonium iodide is used as a source of phosphine. Gas masks approved by the Bureau for respiratory protection against phosphine include the GMC-SS-1, Mine Safety Appliances Co.; the LG-10 and LG-10G, Willson Products Division, The Electric Storage Battery Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966