Search Documents

By R. Barany

The heats of formation at 298.15° K of calcium tungstate, calcium molybdate, and magnesium molybdate were determined by solution calorimetry. For the heats of formation from the elements, the values obtained were calcium tungstate, -402.4 ± 0.5 kcal/mole, calcium molybdate, -369.5 ± 0.3 kcal/mole, -334.8 ± 0.2 kcal/mole. For the heats of formation from the oxides J the values obtained were calcium tungstate, -49.2 ± 0.4 kcal/mole, calcium molybdate, -39.6 ± 0.1 kcal/mole, and magnesium molybdate, -12.9 [ ] 0.1 kcal/mole.

Jan 1, 1962

By G. H. Cobb, J. L. Johnson, H. H. Heady

An infrared absorbance technique is described for analyzing anodic gases produced during the electrowinning of uranium , thorium , and rare - earth metals in molten fluorides . Typical components determined qualitatively in a gas sample are CO , CO₂ , CF4 , C₂ Fe , C3F8 , COS , CS₂ , and SiF4 . About 20 minutes are required to record and interpret the spectrogram , and report quantitative results for CO, CO₂ , CF4 , and SiF . The procedure is used for control during electrolysis .

Jan 1, 1964

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By H. D. Baylor

This is the first of a series of papers describing mining methods and costs at cement plant quarries throughout the United States and deals directly with those methods employed and costs obtained at the quarry of the Louisville Cement Co. located at Speed, Ind. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Mr. J. M. Buohheit, superintendent of quarries, and Mr. H. E. Schoonover, quarry engineer, in furnishing data and in compiling this report.

Jan 1, 1930

By J. W. Jensen

Alloys of manganese and copper containing from 65 to 80 percent manganese possess mechanical strength and vibration-damping capacity in an unusually high degree. The success of their use in reducing vibration in structures depends, to some extent, on their fatigue properties. This report describes the results of fatigue tests on alloys of four compositions. Three metallurgical conditions were investigated for each alloy. Or the basis of the data in this report, the general rule that vibration-damping manganese-copper alloys are comparable to mild steel in hardness and strength may be extended to include fatigue strength. Methods for casting and fabricating these alloys were described in a previous report,4 which contained data on the mechanical and damping properties of the solid-solution alloys, and on alloys aged for 2 hours at 450° C. The aging heat treatment of solution-treated alloys results in optimum mechanical and damping properties throughout the range of specified composition. However, in the present work, measurements also were made on alloys aged for 2 hours at 500° C., because it was theorized that the additional precipitation of a-manganese under these conditions might have a pronounced effect on the fatigue strength of the alloy.

Jan 1, 1961

By T. R. Rehak

Blasting operations are an essential element in the recovery of our Nation?s mineral resources. The mining industry uses billions of pounds of explosives annually. The majority of blasting occurs in surface mining operations. Blasting results in the fragmentation and often the projection of rocks. Frequently, the rocks are thrown beyond the expected limits. Flyrock and failure to secure the blasting area dominate blasting-related accidents in mining, especially in surface mining. Blasting accidents in the mining industry tend to result in critical injuries or fatalities. Accident reports and information collected from the Mine Safety and Health Administration (MSHA) and other government agencies provide supporting evidence. According to the data collected, blasting-related accidents (in mining) were 11 times more severe than all other types of mining accidents. Blasting accidents are not unique to mining operations - the same situation exists in the construction field. In this paper the authors have compiled a list of the primary causes of flyrock and the failure to secure the blast area. In the next phase of this project, typical blasting scenarios will be reviewed which will highlight the main reasons flyrock and/or lack of blast area security occur. This will alert miners and construction workers to the current problems/hazards associated with blasting and to identify other safety measures to protect personnel.

Jan 1, 2000

By H. D. Jacobs

The Bureau of Mines undertook a research program to insure an adequate supply of iron raw materials for future iron and steel making needs. A sample was obtained of oxidized taconite from the western Mesabi Range in Minnesota, and the metallurgical response of the taconite to beneficiation by a process that included selective flocculation-desliming-cationic flotation was evaluated. The sample contained 35.3 pct iron and represented approximately 2 billion tons of crude material. Selective flocculation and flotation were evaluated in a pilot plant with a feed rate of 900 Ib/hr. Concentrates averaging 61.7 pet iron and 5.1 pet silica were obtained, with an accompanying iron recovery of 67.2 pet. About 83 pct of the process water requirements were reclaimed from the slime and froth tailing and then recycled.

Jan 1, 1980

By Martin J. Gavin

In an earlier paper (Karrick, Lewis, C. A convenient and reliable retort for assaying oil-shales for oil yield: Bureau of Mines, Reports of Investigations, Loral No. 2229, March, 1921. Reprinted in Eng. and Min. Jour, April 30, 1921, also in Mining & Met., May, 1921) which describes the apparatus and method used in the laboratories of the Bureau of times for assaying oil-shales, no mention is made of the quality of oil obtained when the apparatus is operated under conditions determined to be most suitable for producing highest yields of oils. So many inquiries regarding the nature of the oil have been received, that it seems advisable to present a short report on the subject. Experimental work indicates that it is possible to vary the quantity and quality of the oil obtainable with the assay retort from a given shale by varying the conditions of retorting. As an example, some figures that are averages for several closely agreeing tests are shown below.

Jan 1, 1921

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

By Jeffrey Shawn Peterson

In past years, the U.S. Bureau of Mines has been involved in safety research that could ultimately re-late the conditions of spark testing and actual use by estimating the simple ignition probability of a circuit in question. A major problem in estimating this probability is that results show a significant variability, even though gas mixtures and electrical parameters may be closely controlled. Some researchers have suggested that the ambient environmental conditions of the testing may influence the results. A series of tests were conducted using a spark test apparatus to simulate a failing electrical circuit. By independently adjusting the temperature, pressure, or relative humidity of the combustible gas mixture, multiple test environments were examined. At each ignition, a computer re-corded the temperature, pressure, and relative humidity of the gas immediately prior to the explosion. These data were then used to establish the effect of the test environment on the ignition probability and to create a mathematical model of the test environment's synergistic effects. The analysis indicated that these effects were not as significant as previously expected. No general algorithm was found that could be used to predict these effects across the range of circuits tested.

Jan 1, 2010

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso- and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, 02, N2, H2, and H2; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By A. Visnapuu

The U.S. Bureau of Mines investigated the oxidation of American Iron and Steel Institute (AISI) Type 304 stainless steel (SS) during annealing in simulated combustion products from several air-CH4 fuel ratios. Atmospheres representing air-CH4 ratios of 14:1 and 18:1 contained free 02, while atmospheres representing 10:1 air-CH, ratio did not. A Cr203 layer formed on SS samples annealed in atmospheres containing free 0, while a Cr-Fe spinel layer formed in atmospheres with no free 02. The Cr203 layer was adherent and presented a protective barrier to metal diffusion, effectively limiting oxidation of the metal substrate. The Cr-Fe spinel was not protective and allowed the diffusion of Fe through the spinel to the gas-oxide interface where it was oxidized to magnetite, which spalled from the surface. This resulted in thick scale layers on samples annealed in atmospheres containing no free 02, as compared to layers formed on samples annealed in atmospheres containing free 02. These results confirmed and explained industrial operators' observations that thick, smoky (fine spalled magnetite) scales form on SS annealed in low free-02 atmospheres, while thin protective oxide layers form on sheets in atmospheres containing free 02.

Jan 1, 2010

By E. C. Perkins

Preliminary experiments are reported utilizing bacteria to leach manganese from a variety of domestic low grade manganiferous materials. In two large leaches manganese extraction ranged from 71.7 to 92.5 percent, and the products analyzed over 48 percent manganese. Nutrient requirements and leaching time experiments were made. The mechanism of leaching is not understood, but is different than the mechanism encountered in the microorganism accelerated leaching of copper in the presence of sulfide minerals.

Jan 1, 1962

By R. T. Johansen

The adverse effects on waterflooding and well-completion methods of clay minerals indigenous to petroleum-production formations recently have received considerable attention. Knowledge of the types and amounts of clay minerals present would allow estimates of the response of such formations to injected or infiltrated water; however, the random distribution of clays in sedimentary formations makes direct evaluation of ?water sensitivity? desirable. A method for the direct evaluation of water sensitivity has been developed, based on measurement of water-vapor adsorption. Correlation of such data with the results of nitrogen-adsorption measurements provides valuable information on the content and properties of clay minerals in sedimentary rocks. The method is relatively simple and has the advantage that it may be used with small, irregularly shaped chips or shale-streaked samples, as well as with typical core samples. Methods previously employed required separating the clay from the rest of the reservoir-sample material and then performing a clay analysis either by X-ray diffraction, differential thermal analysis, liquid permeability, or a combination of these methods (2,3) .3/ This water-vapor-adsorption method requires measuring only a few points on the isotherm to tell whether or not the sample is water sensitive. The goal of these measurements is not to determine the type or amount of clay present, but what will be its sensitivity to flood water. This method gives a direct means of solving this problem.

Jan 1, 1958

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

To minimize the equipment operator?s respirable dust exposure in enclosed cabs of mobile equipment by install-ing cab filtration and pressurization systems and by keep-ing doors and windows closed. Background Enclosed cabs are used on mobile equipment to protect operators from health and safety hazards. The primary health concern is overexposure to respirable dust. Examples of such equipment in mining include drills, dozers, haul trucks, and other equipment. When equipment is new, the operator?s dust exposure is normally at acceptable levels. As the equipment ages and gaskets and seals deteriorate, the air quality inside an enclosed cab can reach a point where it is no longer at acceptable levels for the equipment operators. In an effort to improve the air quality in enclosed cabs of older mining equipment, NIOSH has been performing research to retrofit cabs with new filtration and pressurization systems. Over the past few years, this research has shown that retrofit systems can substantially improve the cab?s air quality back to safe and acceptable levels. How-ever, this is only possible when a positive cab pressure is achieved and maintained. Thus, when a cab door or window is opened, the cab pressure drops to zero and the cab filtration and pressurization system is rendered ineffective. During a recent field study, the magnitude of this impact was noted when a drill operator repeatedly opened the cab door throughout the course of the drill cycle. Upon closer examination, it was determined that the cab door was being opened to manually guide the next drill steel into place each time an additional section of steel was needed to drill deeper holes.

Sep 1, 2008

By W. W. Adams, T. D. Lawrence, D. R. White

"This paper presents the results of the eleventh yearly accident-prevention contest, the National Safety Competition of 1935, conducted by the United States Bureau of Mines. Participating in the competition were 336 mines and Quarries in 37 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies 'Sentinels of Safety.Since these annual contests were begun 11 years ago the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the pre¬vention of accidents has been achieved, as is indicated by an almost constant downward course in the accident-frequency rates for the contest group as a whole during the past 11 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the period and a downward trend during the latter part, except in 1930 and 1934, when two disastrous explosions occurred with heavy loss of life, and in 1935, when there was an increase in the number of fatalities although no major disasters occurred. The accident rate for 1935, both as to frequency and severity, was higher than for 1934.The National Safety Competition is conducted by the Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the fasts contained in the accident reports which the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics that constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting from industrial accidents."

Jul 1, 1936

By E. A. Magill

The Bureau of Mines has begun a study of the copper resources of the Cascade Mountains of Washington. The program includes reconnaissance of mineralized areas and examination and occasionally limited exploration of deposits that are considered characteristic of an area. The Bureau of Mines believes that published information may assist industry in searching for new sources of copper. The Miners Queen is one of a few Cascade Mountain deposits selected for prelim¬inary exploration. The investigation was not planned to delineate the ore body. A diamond-drilling program was carried out at the Miners Queen mine in the summer of 1955. Five diamond-drill holes were completed, totaling 628 feet. Two 35-foot shafts were dewatered, and all accessible underground and surface workings were examined.

Jan 1, 1957

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

Researchers with the National Institute for Occupational Safety and Health (NIOSH) have developed a training module to educate both new, inexperienced miners as well as veterans on important issues related to self-rescue and escape procedures. These include: (1) physical and environmental conditions that can be encountered in a mine after a major explosion, (2) knowledge of emergency meeting locations and escape routes, (3) the importance of using self-rescuers, even in seemingly clear air, to keep the lungs isolated from contaminants, and (4) why miners should not go off to look for others who are missing. In addition, the module may stimulate miners to think about and discuss mine explosions and the devastating effects of such an event.

May 1, 2009