Search Documents

By J. P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, including two red shale, two fireclay, a silica, a silicon carbide, a carbon, and a high-alumina brick, were evaluated. Samples were exposed to 40 wt pct HN03 at 70° and 90° C and 60 wt pct HN03 at 50°, 70°, and 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were generally small or not detected, except for a strength drop in the high-alumina brick, which decreased in strength when exposed to the chosen acid concentrations at 90° C. Vol-ume and weight changes were also measured. The leach rates of Al, Ca, Fe, K, Mg, Na, Si, and Ti were monitored. Increasing temperature or a decrease in the acid concentration resulted in an increased ion leach rate. Of the conditions tested, the most severe corrosion occurred at 90° C for a 40-wt-pct-HN03 solution. The silica brick had the best overall acid-resistant properties, followed by a red shale and a fire-clay brick. The carbon and silicon carbide bricks are not recommended for service.

Jan 1, 1984

By F. D. Everett

The exploration work on a seleniferous tuff deposit near Lysite, Wyo., was confined chiefly to an area of approximately 1 square mile selected on the basis of prior examination and sampling work by the Bureau of Mines. This area was superficially explored by digging and sampling over 2,000 feet of trenches and 15 test pits. The surface sampling indicated that the deposit might contain a multimillion-ton reserve of easy-to-mine volcanic tuff assaying more than 0.01 percent Se. Later, 11 holes, ranging in depth from 57 to 135 feet and totaling 929.4 feet, were drilled under contract using a dry rotary drill. Samples for assay were cut at 5-foot intervals or at noticeable physical changes in the formation being drilled. Of the 206 samples assayed from the drilling, only 8 contained more than 0.005 percent selenium, and 2 of these assayed as high as 0.012 percent Se. Chemical analyses of samples obtained from six holes drilled by the Nugget Coal & Timber Co. to the south of the area explored by the Bureau of Mines showed that no selenium-bearing formations were encountered in that work. Two of 72 samples taken from 42 validation pits dug by claim holders contained more than 0.005 percent selenium. The exploratory work established that the selenium mineralization is erratically distributed in small irregular bodies and is not confined to any one tuff bed. Because of the lack of correlation between the infrequent showing of low-grade tuff, neither the extent nor grade of the reserves could be calculated.

Jan 1, 1957

By Michael S. Miller

The U.S. Bureau of Mines (USBM) conducted mineral investigations in the 1,227,000-acre Emigrant Trail study area of Nevada during 1992. During the USBM investigation of 25 areas of development interest, 190 mineral localities were identified and 260 rock and 50 alluvial samples were taken. At least 0.5 million troy ounces of gold, 2.3 million troy ounces of silver, 3.3 million pounds of copper, 10.9 million pounds of lead, 2.4 million pounds of zinc, 500 tons of alunite, 40,000 tons of sulfur, 9,000 pounds of mercury, and 21,000 pounds of tin have been mined from the area and vicinity. Adjacent to the study area, gold is being mined at large, open-pit gold mines, the Hog Ranch and Hycroft Resources, Inc., Sulphur mines, and new production is planned at the Rosebud LAC/Equinox. Hog Ranch mine is nearing depletion, but resources of more than 0.5 million troy ounces of gold and about 5 million ounces of silver are estimated for the Rosebud LAC/Equinox project and more than 0.4 million ounces of gold for the Hycroft Resources, Inc., Sulphur mine. Significant investigations are occurring at SP Ridge and other sites near Scossa and at the Dan claims in the Southern Calico Mountains. Precious opal, placer gold, and geothermal energy resources occur in the study area and vicinity.

Jan 1, 1993

By Jack D. Ramsdell

Electrorefined, magnesium-reduced, and sodium-reduced titanium samples were evaluated for recrystallization behavior, effect of cold rolling on tensile properties, and bend ductility. Curves were determined for the softening of 2.5 to 80 percent reduced cold-rolled metal that was annealed over a temperature range of 300° to 800° C. Upon annealing, coarsening of the grains was found to occur for reductions in thickness of less than 20 percent in titanium made by all three processes. The presence of metallic impurities greatly inhibits coarsening for reductions in thickness below 20 percent, but for reductions in excess of 20 percent grain size is essentially constant at each annealing temperature. The three grades of titanium did not harden excessively from cold rolling; both tensile and bend ductility were good for reduction in thickness up to 80 percent. Upon annealing, softening occurs between 400° and 600° C., and, based on microstructure and property studies, full annealing is accomplished after 30 minutes at 700° C. for the magnesium-reduced and electrorefined titanium and at 800° C. for the sodium-reduced titanium.

Jan 1, 1960

Objective: To evaluate the quantity of ventilation air reaching the face of a 40-ft box cut during a 40-ft, two-pass, extended cut and to examine ways to increase this quantity of air.

May 1, 1998

Modify conventional mining practices to reduce significantly the amount of material brought to the surface from underground mines, or to ?re-mine? existing surface mine dumps by backfilling empty underground stopes.

Jan 1, 1994

During 1999, there were six fatalities in surface mines involving haulage equipment colliding with a smaller vehicle or person, or backing over the edge of a dump point. All of these fatalities can be attributed to the extensive blind areas around large haulage equipment. Researchers at NIOSH are investigating various technologies that can be used to monitor these blind areas and provide information on nearby obstacles to an operator. So far, the technologies listed below have been tested on dump trucks used in surface mining. The selection of these systems was based on their ability to handle the tough environmental conditions found in mining operations and how well they detected obstacles out to 40 or 50 feet beyond the rear of large dump trucks. Some of the manufacturers of available collision warning and camera systems are also listed.

Jan 1, 2001

By John W. Buch

In 1947, a Korfmann universal shearing machine was installed in a mine in the Southern field of the Pennsylvania anthracite region. The machine was obtained from Germany by the Bureau of Mines after the close of World War II as a part of a program of experimental work to increase the output and lower the cost of anthracite, which the Bureau of Mines initiated in 1944 when an agreement was made with an anthracite-producing company for use of one of the company's mines as a testing ground for certain mechanical equipment procured or developed by the Bureau. A major objective is to develop a mechanical mining method that will increase the rate of advance and reduce the coat of development of coal gangways in steeply pitching seams. In addition to the time to be saved in driving these openings by machine, it is felt that further economies will be affected by making it possible to concentrate producing sections into smaller compass and that savings will ensue in supervision, maintenance, and time required for mining a section. A higher percentage extraction also is an objective. Test work covered by this report was concentrated on the power characteristics, maneuverability, effectiveness, and general qualities of the Korfmann machine in cutting coal, the cutting tests representing the first use of a machine of this kind in steep-pitch mining in the United States.

Jan 1, 1951

By F. D. DeVaney

The supply of manganese is a subject of much interest. The idea of obtaining it from rhodochrosite-MnC03 is attractive because the carbonate is supposed not to be so contaminated with impurities as the commonly utilized oxides. Large bodies of rhodochrosite-bearing rock have been known for a long while to exist at Butte, Mont. Hence samples were obtained from that place. In the two samples examined quartz was the chief diluting substance. The leaner sample was about one half quartz; some copper, lead, zinc, and iron sulphides were also present. The rhodochrosite amounted to about 40 per cent, so that the sample had a tenor of about 20 per cent manganese. This sample was the subject of the examination reported herein.

Jan 1, 1928

By J. J. Jakosky

"This report is the second of a series dealing with electrical methods of underground communication nd signalling, and is a discussion of some of the factors involved in -applying radio in mines.A previous report2 described the results obtained by the use of the ""T.P.S."" of ground-conduction method of signalling, and outlined in a general way the requirements for a practical mine communication apparatus.The popularity of radio, the development work on new apparatus, a desire to render humanitarian service to entombed miners, and an endeavor to find new uses and applications for radio stimulated many persons to attempt the application of radio to mine rescue purposes. A number of experiments on underground reception from surface broadcast stations have been conducted by different experimenters in various parts of the country and the widespread interest in the subject is shown by the fact that these tests have been con¬ducted in many States, The Bureau of Mines has received information regarding, underground tests in Illinois, Pennsylvania, Arizona, Utah, Idaho, Colorado, Michigan, Wyoming, Kentucky, New York, Connecticut, and in England, Germany, Italy, and Franc.From occasional press notices and illustrations in different papers it may appear that radio communication in mines and in tunnels being excavated is en established fact, and that the method is comparatively simple. As a matter of fact the reverse is the case."

Apr 1, 1924

By Eliot J. White

The Bureau of Mines tested cores from 35 wells from 14 oil-producing zones in southern Illinois, southern Indiana, and western Kentucky to determine why rates of water injection were apparently low in some zones. Since these zones contain only minor amounts of clay minerals, it is concluded that permeability reduction results from movement of dislodged silica particles and other material, including the clays, that lines the pores. Both single-phase and two-phase permeability measurements, however, indicated that most samples had only low to moderate water sensitivity, so that permeability reduction due to such particle movement should usually not be of practical significance. The effective permeability to water was considerably lower than the effective permeability to oil during two-phase flow measurements, as is typical of most reservoir rocks. It can be concluded, therefore, that relatively high injection pressures will be required in waterflooding thin zones or zones having low permeabilities.

Jan 1, 1966

By S. McGinn, G. Schnakenberg, D. Petrie, A. Bugarski, M. Grenier

As part of the Diesel Emissions Evaluation Program (DEEP) consortium, Noranda Inc. has undertaken a field project to evaluate the overall performance of the latest diesel particulate filter technology (DPF) at its Brunswick Mine in Bathurst, New Brunswick. Performance of the filtration systems is evaluated with respect to their ability to reduce tailpipe emissions and concentrations of diesel particulate matter (DPM) and noxious gases in mine air, efficiency of filter regeneration process, maintenance requirements, reliability, and acceptance. Four different particulate filter systems deployed on heavy production vehicles are subjected to an 18-month field evaluation. Over the evaluation period the vehicles will have accumulated approximately 4000 operating hours in production. This paper presents the results of testing conducted mid way through the 18-month field trials. The 400- meter section of the mine drift at 525-5 sub level, hereinafter referred to as the "isolated zone" was isolated between intake and exhaust fan systems and sealed with bulkheads against leakage. The isolated zone was ventilated at the rate required per CSA Standards and issued by CANMET for the engines tested. Four vehicles, two load-haul-dumps (LHDs) and two trucks, retrofitted with particulate filter systems were tested along with a new identical model LHD and truck equipped with exhaust systems consisting of a catalytic converter (DOC) and muffler. The test vehicles were operated individually inside the isolated zone for approximately 4 hours over simulated production duty cycles. Measurements of ambient concentrations of particulate matter, tailpipe emissions, and engine parameters were performed for each of the tested vehicles. The DPM samples for carbon were collected at the most up- stream end of the isolated zone, at the vehicle next to the operator, and at the most downstream or exhaust end of the isolated zone. The DPM samples were analyzed for total (organic and elemental) carbon using NIOSH Analytical Method 5040. Ambient concentrations of particulate matter at the exhaust end of the zone were also measured using Scanning Mobility Particle Sizer (SMPS), and real time PAH monitor (PAS 2000). Efficiency of the filters was also evaluated on a basis of tailpipe measurements performed using raw exhaust instruments the NanoMet and the UGAS. In addition, relevant engine parameters were obtained using Detroit Diesel Diagnostic Link (DDDL) and from exhaust backpressure and temperature measurements. Results from the tests proved conclusively that diesel particulate filters can significantly reduce the concentrations of air- borne DPM, but not without careful monitoring of both ambient and tailpipe emissions and not without careful attention with respect to maintaining the integrity of the DPF systems.

In 1991, the USBM (U. S. Bureau of Mines) evaluated the mineral resources of the 174,550-acre Bear Creek-Poker Peak area. Located 40 air miles east from Idaho Falls, ID, the study area is in the Caribou National Forest but is mostly administered by Targhee National Forest. USBM personnel mapped and sampled mines, prospects, and mineralized sites in and near the study area. Five types of mineral occurrences were identified in the study area: phosphate, limestone and travertine, placer gold, coal and uranium (the latter contained in the coal), and oil and gas. The study area has a high potential for oil and gas; evaluation of these commodities were beyond the scope of this study.

Jan 1, 1992

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents--ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By Robert C. Bates

This Bureau of Mines report converts published data on the cost of ventilating uranium mines to a common price base and analyzes these data to determine the cost per ton of uranium ore at various levels of radiation exposure control. There appears to be an exponential increase of cost as the radiation level is lowered. The 1967 base costs are extrapolated to present dollars, and some cost comparisons are given for other radiation control measures.

Jan 1, 1981

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines" in various foreign countries. In the preparation of this interpretation of the laws of Norway, use has been made of William R. Orrmins' translations of various acts of the Norwegian Government, which were forwarded from the American consulate at Oslo^ and transmitted to the Bureau of Mines through the courtesy of the State Department. This digest is released subject to amplification and correction, if necessary, by the proper American foreignservice officers.

Nov 1, 1932

By Floyd G. Anderson

Owing to the rapid growth of the perlite industry in recent years, the Bureau of Mines has received numerous requests for information relative to the possible harmful effects of breathing dust resulting from the processing and use of perlite. As published information on the composition of perlite is rather meager, consisting chiefly of conventional chemical analyses, samples of crude and expanded perlite from 9 deposits in 6 Western States were studied. Crude perlite ores were examined petrographically and analyzed by chemical, spectrographic, and X-ray-diffraction methods. Sized crude and expanded perlites were analyzed chemically for total free and combined silica content.

Jan 1, 1956

By Richard G. Sandberg

The Bureau of Mins, U.S. Department of the Interior, is investigating a hydrometallurgical procedure to conserve cobalt, nickel, and copper by recovering the metals from the matte byproducts of smelting Missouri lead ores. For want of adequate processing technology the mattes are now either unmarketable or marginally so. The procedure involves leaching with manganese dioxide and sulfuric acid to obtain copper, nickel, cobalt, lead, and manganese sulfates, and elemental sulfur as expressed by the following reaction: MS + MnO2 + 2H2SO4 ? MSO4 + MnS04 + S° + 2H2O, where M = Cu, Ni, Co, and Pb. The leach solutions, containing near theoretical amounts of sulfuric acid and manganese dioxide at 85° to 100° C, convert up to 98 pct of the cobalt, nickel, and copper in the mattes to sulfates in less than 2 hr. As they are formed, the cobalt, nickel, and copper sulfates are dissolved leaving a residue of lead sulfate, lead, sulfur, and gangue. The soluble metals are recovered from the leach solutions by caustic and sulfide precipitation, and the residue returned to the smelter for lead recovery. The manganese can be reclaimed from the spent leach liquor as manganese oxide and recycled to leaching.

Jan 1, 1979

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936