Search Documents

By J. Sammarco

Proper illumination is critical to a miner?s ability to detect hazards in underground mines. Moving hazards are often located in the miner?s peripheral field-of-view, while slip/trip/ fall hazards are often located in the forward field-of-view. The objective of the research described in this paper was to determine if light-emitting diodes (LEDs) improve visual performance as compared to traditional incandescent (INC) cap lamps. The research presented focuses on comparative studies of a National Institute for Occupational Safety and Health (NIOSH) prototype LED, a commercial LED and an INC camp lamp. Thirty subjects participated in these studies, with ten subjects in each of the following age groups: 18 to 25 years, 40 to 50 years and 51+ years old. Visual per­formance was quantified by the subjects? speed and accuracy in detecting hazards, while visual performance for disability glare was quantified by the use of contrast sensitivity tests. Results suggest that LEDs with a visible spectrum containing a higher concentration of the shorter wavelengths can enable visual performance improvements with respect to disability glare, the detection of moving hazards in the peripheral field-of-view and the detection of floor hazards in the forward field-of-view. The NIOSH prototype LED cap lamp provided the best visual performance improvements for the older age groups in every test.

Jan 1, 2009

By G. S. Rice, R. V. Wheeler

"In September 1923, a proposal was made through official diplomatic channels by the British Safety in Mines Research Board to the United States Bureau of Mines for ""closer cooperation between the two countries in investigations into the causes and means of prevention of mining dangers."" This proposal was cordially accepted by the Bureau of Mines and was officially approved.In the spring of 1924 cooperation was .formally begun. It contemplated, as stated officially, ""full exchanges of information, a joint program of research, and periodic exchange of personnel so as to assure concordant results. By making the resources of both organizations available it will hasten the attainment of results, will secure better: checks for, accuracy, and in the end will save money for both by avoiding duplication and repetition.""This joint work has been carried-on successfully since that time and has developed valuable results, reports on which have been issued from time to time. The progress report which follows gives the results of the studies and work carried on in 1929.During 1929 all the phases of our cooperative research, begun in previous years, have developed normally. The exchange of formal monthly reports on all programs of mutual interest has been continued and has proved an invaluable, means of maintaining contact between the investigators of both organizations. There has been no diminution in the exchange of routine progress reports on specific subjects or in direct correspondence. The interchange of personnel has been maintained, and we can say that the mutual benefits to be derived from this form of cooperation are so great as to be difficult to overestimate. It leads to an appreciation of methods of research and modes of thought in the interpretation of results obtainable in no other way, and engenders a frankness and intimacy which must continuously enhance the value of future cooperation.Dr. S. R. Katz, who was assigned for service with the Safety in Mines Research Board in April, 1928, returned to America in May, 1929. During his stay in England he completed, in cooperation with members of the board's staff, the equipment of a gas-mask laboratory and designed and tested a new form of gas-mask canister. A publication of the Safety in Mines Research Board dealing with this investigation has been prepared and approved and will .be .issued in the near future. In additions Dr. Katz imparted to those with whom he was associated much of his knowledge and technique regarding his particular subjects. He delivered two lectures to the board's staff, the subjects be ""Gas Masks"" and ""The Intensity of Odors"", and gave papers before the Midland Institute of 'lining Engineers and the Birmingham University Mining Society on the subject of ""Industrial Gas Masks""."

Jun 1, 1930

By H. -F. Krausse

Roof failures in underground coal mines are related to the lithology and geologic structure of the roof. There are two distinct suites of roof rock above the Herrin (No. 6) Coal in Illinois, and each has distinctive patterns of structure and roof failure. In black shale-limestone roof areas, roof instability is correlated with thinning of limestone beds and presence of faults and clay dikes. In gray shale roof regions, the prime roof hazards are posed by rolls, shear bodies, and presence of coal or carbonaceous partings in the roof. Most structural features examined are believed to have formed during early stages of sediment diagenesis and compaction. Structural trends and lithologic patterns are strongly interdependent for this reason. In many cases geologic patterns are so complex and locally variable that prediction of roof stability far in advance of mining is difficult. The need for greater flexibility in roof control planning is apparent.

Jan 1, 1979

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By L. C. IlsLey, Charles M. Means

The descriptive rather than the strictly technical meaning of many of the terms and expressions used in the electrical rules is given in order to assist in their interpге- tation . ALIVE . At a potential measurable with a voltmeter and different from that of the earth or another conductor . (Static charges should be determined with an electrostatic voltmeter . This condition may apply to current - carrying parts , to noncurrent - carrying parts and adjacent material where a failure of insulation has taken place , and to objects having stored or static electricity . ) ALTERNATING CURRENT . A current that changes in direction -- positive or negative-- a certain number of times per second , depending upon the number of poles and speed of the generator . AMMETER. An instrument for measuring current , indicating in amperes . AMPERE . A term applied to denote the rate of current flow . ( Analogous to " gallons per minute " in a hydraulic system . ) APPROVED . Accepted as suitable by a competent committee , board , or organization designated by those adopting the rules . ductors . ARMOR . A steel or equivalent metallic covering for one or more electric con- AUTHORIZED PERSON . Anyone commissioned by the official in charge of the mine or his deputies to carry out certain duties incident to the generation , transformation , and distribution or use of electric energy in the mine , such person being one who is competent within the purpose of the rule in which the term is used .

May 1, 1930

By W. D. Riley

The Bureau of Mines is conducting research on methods for the rapid identification and sorting of mixed scrap metals and alloys so that domestic scrap resources can be fully utilized. One method, spark testing, is the examination of the pattern of sparks that results when a metal or alloy is ground on an abrasive wheel. This technique requires experienced sorters. Bureau researchers have shown that spectrophotometric methods can be used in lieu of the highly skilled sorter. The spectra of a mild steel, an HSLA steel, several stainless steels, and four nickel-base alloys have been measured. Differences in the spectra that are sufficient for identification are apparent.

Jan 1, 1985

Although alternating-current (a.-c.) power systems and equipment have been used in coal mining for many years, most mines in the United States are powered mainly by direct current (d.-c.). There are several logical reasons for this, but the use of d.-c, equipment is, in most instances, a direct outgrowth of the original practice of using such power for haulage systems. For traction equipment such as the electric trolley locomotive the d.-c. motor has ideal operating characteristics, and thus it has been widely used for haulage locomotive service. The first efforts at electrification of coal mines started with the haulage system and from there branched out to include the many types of electrically powered mining machinery used in the industry today.

Jan 1, 1960

By J. A. Herdlick

At the request of the War Production Board a preliminary examination of the Big Ben molybdenum prospect near Neihart, Cascade County, Mont., was made by the Bureau of Mines under G. N. Bennett, mining engineer, Bureau of Mines Montana district office, in September 1942. Formal investigation, consisting of sampling, core drilling, and metallurgical testing, was later undertaken and completed in 1943. Field work was directed by Robert D. O'Brien, mining engineer, Montana district office, under the supervision of E. W. Newman, supervising engineer, Montana district office. This report describes the deposit, presents the factual data obtained from the sampling and core-drilling operations, and summarizes the results of the metallurgical studies. The deposit was first located and prospected in 1922 by the present owner, Frank Mansikka of Neihart, Mont. Periodic examinations made by responsible mining interests were culminated in 1938 when the Federal Mining & Smelting Co. optioned and investigated the property. No ores have been produced from the deposit to date.

Jan 1, 1949

By M. E. Tyrrell, J. Koster

This work was undertaken to determine the feasibility of making mixed diborides of two metals directly from the metal oxides , boron carbide and carbon . The diborides (Ti , V ) , B₂ , (Ti , Cb) B₂ , and ( Ti , Ta ) B₂ were prepared in a crucible resistance furnace at 2,100 ° C , and X- ray- diffraction analyses showed each was a homogeneous solid solution containing approximately equal molar contents of the given diborides . The diboride powders were cold - pressed ; sintered to 2,300 ° C , and evaluated for mechanical strength , rate of oxidation , and resistance to molten metals . The diboride ( Ti , Ta ) B₂ exhibited the best mechanical properties ; the diboride ( Ti , Cb ) B₂ , the lowest cumulative rate of oxidation . The mixtures were stable in the presence of molten aluminum and copper but were attacked by molten Ti , Zr , and Cr .

Jan 1, 1964

Prevention of coal-mine explosions depends largely upon thorough knowledge of the causes that initiate explosions. A review of coal-mine explosions in one geographical area when supplemented by nationwide data of similar nature, should serve as a guide for the adoption of measures for explosion prevention. Explosions in bituminous-coal mines of the United States during the 10 years ended December 31, 1932, ranked third in the causes of fatal accidents and constituted 16.1 percent of all fatal accidents in bituminous mines. Kentucky now ranks fourth in coal output in the coal-producing States of this country; a study of the coal-mine explosions in this state will be of definite interest locally among coal-mining people, as well as to those in the coal-mining industry who are concerned in preventing coal-mine explosions. This circular reviews gas and dust explosions in Kentucky coal mines to show their hazards, to point out the influence of certain factors in causing explosions, and to indicate the effectiveness of preventive measures.

Jan 1, 1934

By D. W. Mitchell

This Bureau of Mines report summarizes experience and past research on methods for sealing abandoned areas of a coal mine and areas from which the pillars have been wholly or partially extracted. The Federal Coal Mine Health and Safety Act of 1969 requires that such areas be ventilated or sealed with explosion-proof bulkheads, but the present study indicates that bulkheads alone cannot isolate areas in a coal mine in which methane and other dangerous gases have accumulated. Gas-air exchanges between sealed and open areas must be controlled.

Jan 1, 1971

By Albert L. Toenges, Henry E. Dekay, James N. Scudder

Support of the immediate roof in coal mines is essential for their safe operation, and timbers are the most common means of support. Their effectiveness depends upon their resistance to decay. The theory has been advanced by some mine operators that rock dust, which is applied to ccal-mine workings to prevent propagation of explosions, accelerates the decay of mine timbers. As the results of part 1 of this study were inconclusive, the study was continued. Its principal objectives are: 1. To determine the effect of rock dusting upon decay of mine timber. 2. To compare the extent of decay of timbers in two mines in which underground conditions are similar. 3. To determine the loss in strength of the timbers after exposure to mine atmosphere. The studies were carried on in the Crucible mine of the Crucible Fuel Co. where the first part of this study was made, and in the Isabella mine of the Weirton Coal Co. The mines are on the Monongehela River and are adjacent.

May 1, 1943

By M. J. Ferrante

Relative enthalpies of high-purity disodium hexatitanate (Na2Ti6013) were measured at the Bureau of Mines to provide new thermodynamic data needed to advance the technology of materials. Measurements from 298.15 to 1,478 K were made by drop calorimetry with a copper block. Tabulated values are listed for the standard relative enthalpy, heat capacity, en-tropy, and Gibbs energy function between 298.15 and 1,500 K. Enthalpy data are also given in equation form and are combined with thermodynamic data from the literature to derive values of standard enthalpies of formation, Gibbs energies of formation, and logarithms of the equilibrium constants of formation. Similar calculations were made for the reaction of Na20 with Ti02.

Jan 1, 1986

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By Richard F. Hewlett

Numerous populations of assays have been simulated for a range of assay values representative of low-grade mineral deposits to facilitate the study of problems encountered in evaluating these deposits. Analysis of these simulated populations of assays (obtained by using statistical probability models for the simulation) makes possible the quantification of the effects of (1) various composite assay intervals, (2) ore reserve computational methods, (3) uneven assay intervals, and (4) various cutoff grades on both the precision and the accuracy of the estimated average grade and tonnage of ore.

Jan 1, 1964

By M. G. Zabetakis

Benzene and toluene are the first two members of an important homologous series whose general formula is CnH2n-6. The members of this series differ in composition from benzene by some integral multiple of CH2; they can all be prepared in the laboratory by the Wurtz-Fittig, Friedel-Crafts and Grignard syntheses. Because &apos;of the industrial importance of these-hydrocarbons, the limits of flammability of eight members of the series have been determined at 100° C.-(A temperature of 1000 C. was chosen because the determination of the upper limit of flammability of p-cymene requires an apparatus temperature. of at least 90° C. As elevated temperature data are available for other combustibles at 100° C. but not at 90° C., all data were taken at 100° C. in order to obtain comparable results.) Minimum ignition temperatures of these combustibles have been determined at laboratory-pressures.

Jan 1, 1951

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

By E. A. Anundsen

The prevention of accidents is considered a necessity at all branches and divisions of the Phelps Dodge Corporation copper-producing operations, and since there is a continual exchange of data on safety accomplishments between the various units, their safety programs are fundamentally similar. Variations in accident-prevention methods result from a difference in emphasis rather than from a difference in the elements themselves. The main copper-producing operations of the corporation ore conducted in Arizona and distributed as follows: Copper Queen Branch, mines division, Fisbee, and smelter division, Douglas, Aria.; Morenci Branch, mines division, Morenci, and smelter division, Clifton, Ariz.; New Cornelia Branch, Ajo, Ariz.; and United Verde Branch, mines division, Jerome, and smelter division, Clarkdale Ariz. As it is not feasible to describe here the safety programs of all branches and divisions, the program at the Clarkdale smelter has been selected for discussion. The United Verde Brach includes the mine and smelter purchased by the Phelps Dodge Corporation in February 1935 from the United Verde Copper Co. The mine at Jerome and the reduction works at Clarkdale are designated, respectively, as the mine and smelter divisions.

Jan 1, 1939