Search Documents

By Sidney Katell

This study presents the economics of the hot-carbonate purification process for removing C02. It considers three variations of the process in order to meet the design specifications, which call for a feed-gas flow of 10 million standard cubic feet per hour (std.c.f.h.) with C02 inlet concentrations of 10, 20, and 30 percent and exit C02 values of 5, 2, 1, 0.5, and 0.1 percent. Inlet pressure and temperature are 350 pounds per square inch [e] (p.s.i.g.) and 300° F., respectively. Estimated capital and operating costs are shown in the following to tabulations: [ ]

Jan 1, 1960

By Mayer G. Hansen

A series of papers dealing with diamond drilling practices, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines, is to be published as information circulars by the bureau. This paper, the first of the series, describes the general practice at the United Verde mine during the last ten years; specific instances cited in the paper refer to 1930, the last year of full operation. The United Verde copper mine is located at the town of Jerome, Yavapai County, north central Arizona.

Jan 1, 1933

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By Robert J. Anderson

"Introductory Statement:In melting the nonferrous metals and alloys for foundry and rolling-mill work, even with the best practice, there is always a loss, due principally to oxidation. Melting losses are a serious source of financial loss in brass and bronze practice, but they are especially serious in the case of aluminum and its light alloys because of the relatively high price of aluminum. The indications are that the melting losses in many aluminum foundries of the United States are at times high, and in some plants (especially where certain furnaces are used) they are entirely too high when compared with the average practice. The fact that the oxidation losses in melting aluminum and its light alloys are high is well known, but it is doubtful whether the factors governing the most suitable methods of melting for a minimum of dross are equally well known. The metal losses involved in melting are worthy of especial attention now because of the rapidly growing importance of the aluminum industry.Factors in the operation of furnaces which affect metal and fuel losses:The essential requirements in the commercial melting of any metal or alloy are that the melting losses should be low, the melting should be rapid, and the melting cost should be low. Certainly it may not be possible to obtain these requirements in any furnace selected at random, and it follows that the design and the operation of furnaces for melting different metals are subjects that warrant the most extensive study and tests. As a general rule, in the industrial operation of furnaces, run on aluminum and aluminum alloys, an effort is made to keep the dross and oxidation losses as low as possible. In attempting to hold dross losses low, numerous factors involved in metal melting may be overlooked, or at least disregarded, and the net practical result may be that the furnace is exceedingly wasteful of fuel. In the case of aluminum and its light alloys, the effect of increasing the temperature of melting, at least in an atmosphere containing free oxygen and nitrogen, is to increase the net melting loss."

Apr 1, 1921

By V. A. Nieberlein

An extractive process was developed applicable to submarginal titanium deposits containing valuable minor constituents; such as columbium (niobium) and iron. The process consisted of reducing the mineral concentrate with coke at high temperature to form a carbide-suboxide sinter, chlorination in the 400° -500° C. range, and fractional condensation of the chlorides. The chlorination procedure recovered 97, 83, and 87 percent of the titanium from brookite, rutile, and ilmenite sinters, respectively, while simultaneous columbium recoveries on the same materials were 85, 50, and 87 percent.

Jan 1, 1957

By N. N. Moelbs

The U.S. Bureau of Mines is conducting research on many topics relating to the hazards of coal mining, increased production, and protection of the environment. One area of research that has received scant attention in recent years is that of water inflows, probably because few fatalities in the United States have been attributed to them. As mining goes deeper, the problem of water in 1ow could increase dramatically because of adjacent or overlying mines in which huge water pools are impounded. Inaccurate mine maps and ineffective barriers can constitute a serious problem for operators both from gradual inflows and sudden inrushes of water. This report describes a wide but ineffective barrier that permitted an average 240-gpm inflow to a developing mine from an adjacent mine. The anomalous geologic structure that facilitated this leakage is described, demonstrating that size, alone, is no assurance against serious leakage. Some recommendations for managing serious water inflow are included.

Jan 1, 1989

By V. A. Marple, K. L. Rubow, S. M. Behm

"An eight-stage cascade impactor, with cut-sizes ranging from 0.056 to 18 um at a flow rate of 30 L/min, has been developed, calibrated, and tested in field programs. This impactor, called a microorifice uniform deposit impactor, has several features not normally found in cascade impactors. Ultrafine particles as small as 0.056 um are collected while keeping the pressure drop moderate by utilizing multiple nozzles (up to 2000) as small as 52 um in diameter. At each stage the collected particles are deposited uniformly over the entire impaction plate by rotating the impaction plate relative to the nozzles and by the correct radial placement of the nozzles. The particle cutoff characteristics (collection efficiency curves) of each stage and inter-stage losses were determined by means of monodisperse aerosols. The cutoff characteristics were found to be sharp and similar for all stages.Inertial impactors are widely used for the size-selective collection of aerosol particles. One reason for their wide usage is that the principle of operation is simple: a jet of particle-laden air is directed at a flat impaction plate. Large particles are collected on the plate while smaller particles follow the airflow out of the impaction region and are not collected. The division between the size of particles collected and those that are not is quite sharp. Secondly, the particles in an impactor are classified by their aerodynamic diameter (an important size parameter in many fields of study, including those related to respirable particle health effects). Thirdly, it is easy to collect particles in discrete size ranges by passing the aerosol through a number of stages (one stage consisting of a nozzle and impaction plae) in series, with each subsequent stage collecting particles smaller than the one before it. This is known as a cascade impactor. Finally, impactors can classify particles over a wide range of particle sizes: as low as 0.005 um (Fernandez de la Mora et al., 1990) and as large as approximately 50 um (Vanderpool et al., 1987).This paper describes a general purpose cascade impactor that has been developed in our laboratory and used in a variety of studies including visibility studies (McMurry et al., 1986; McMurry and Zhang, 1989), underground mine studies (Marple et al., 1986; Rubow and Marple, 1988; Rubow et al., 1988), and general atmospheric pollution studies (Macias et al., 1981; Dzubay et al., 1984). The impactor, called a microorifice uniform deposit impactor (MOUDI model 100, MSP Corp., Minneapolis, Minn.), is the integration of two earlier impactor de¬velopments: the microorifice impactor (M01) (Kuhlmey et al., 1981) and the uniform deposit impactor (UDI) (Marple et al., 1981).The MOUDI has several features normally not found in other cascade impactors. These include collection of particles as small as 0.056 um in aerodynamic diameter with a moderate pressure drop, uniform particle collection on the impaction plates, inter-changeable impaction plates to allow for the plates to be easily and quickly changed in the field, and covers for these substrates to provide a means for safe storage and/or transport of the collected particles to the laboratory for analysis."

Mar 1, 1992

By B. J. Scheiner

Oxidation procedures based on the chlorine-hypochlorite system were investigated for improving gold recovery from carbonaceous gold ores. The oxidation pretreatment prior to cyanidation was accomplished by (1) addition of sodium hypochlorite to ore pulp, (2) by addition of chlorine to ore pulp, and (3) by generation of hypochlorite in situ by electrolysis of a brine solution used to pulp the ore. Gold extraction of 90 pct was achieved by cyanidation of carbonaceous ore that had been pretreated with 20 Ib per ton sodium hypochlorite at 50° C for 4 hours. Similarly, pretreatment of the ore pulp with 35 1b chlorine per ton at 24° to 30° C and 15 hours reaction time resulted in 89-pct gold extraction by subsequent cyanidation. Concomitant studies showed that electrolyzing the pulp prepared with a brine solution was equally as effective as electrolyzing hypochlorite and chlorine for oxidizing carbonaceous ore constituents that are deleterious to cyanidation. Gold extraction of 90 pct was obtained by electrolysis when 275 lb of are was treated at 200 amp for 7 hours in an 8-to 10-pct salt solution. Power consumption was in the range of 60 kwhr per ton.

Jan 1, 1972

By S. P. Howell

"Technical statistical study has been made of accidents in the anthracite region of Pennsylvania in which explosives were involved. The data have been taken from the accident reports in the files of the department of mines of Pennsylvania, supplemented by inquiries in the field.This study has disclosed a wealth of information regarding the nature and the cause of accidents that occurred where different means of firing shots of explosives were employed. In the anthracite region shots are fired with fuse, with squibs, and with electricity,Many of the salient features of this accident experience are illustrated in this report of investigations, and a number of recommendations are made to reduce the hazards of each of these three methods of shot firing.Experience seems to demonstrate that, under conditions in the anthracite region, electric firing of shots is substantially the safest method; that accidents wherein fuse is employed are more frequent than accidents in which electric firing is employed; and that the number of accidents when squibs are employed far exceeds those in which either fuse or electric firing is used."

Mar 1, 1930

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

Any communication system requires at least three elements in order to function: a transmitting device, a receiving device, and a transmission line or propagation medium. Even the device children use, tin cans connected with string, consists or these three elements. One speaks into one can (transmitter), which vibrates at the same frequencies as the voice. The string (transmission path) picks up the vibrations of the can and carries them along its entire length. The other can (receiver) detects the vibration and reproduces the original sounds to a lesser extent depending on distance, tightness of string, type of string, etc. All communication systems depend on these three elements: transmitter, transmission path, and receiver. Communication systems can be divided into three fundamental categories: wired phone systems, radio systems, and carrier current systems. Sections 2.2, 2.3, and 2.4, respectively, describe these systems and explain the basic principles of how each works. Hybrid systems are those systems that use various combinations of the three basic communication methods. Hybrid systems are described in section 2.5. There are some other methods of signaling (stench warning, bell signaling, etc.) that can be used in underground mines to transmit or convey information. These systems, although they cannot be considered true communication systems since they do not provide voice or even two-way communication, are briefly described in section 2.6. 2.2 Wired Phone Systems Wired phone systems are all those that depend on a wire connection between phones with the wire carrying the voice signals. Figure 2-1 is a diagram of two typical wired phone systems.The top panel shows a simple single pair party line system. In this system each phone is connected to a common pair of wires, and a person speaking into one phone will be heard at all the other phones on the line. The bottom panel shows a multipair private line phone system. In this type of system, each phone is connected by its own individual pair of wires to a central switch or telephone exchange. To establish a call between two phones in this system, the lines between the two phones must be connected (switched together) within the telephone exchange. In early exchanges, the connections were made manually by an operator. These exchanges are called Private Branch Exchanges (PBX's). Today, equipment within the exchange can automatically connect each phone to any other phone in the system. These exchanges are called Private Automatic Branch Exchanges (PABX's). There are many different types of automatic exchanges. Some utilize switches to physically make each connection according to the number dialed. Other, more advanced exchanges are completely solid state and may even be computer controlled. [ ]

Jan 1, 1984

By H. D. Bemis

This paper describing the milling practice of the American Metal Co. at its Pecos con¬centrator is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. ACKNOWLEDGMENT The author acknowledges the assistance rendered by Guy Martin, metallurgist, H. E. Brown and J. H. Hastings, chemists, and Thomas J. Fahey, accountant, in gathering and pre¬paring the data presented in this paper.

Jan 1, 1932

By Aldo L. Furno

Sufficient quantities of combustible vapors are released by some sulfurs to produce flammable atmospheres under prolonged storage. Hydrogen sulfide and carbon disulfide appear to be the principal flammable constituents in the vapor space above molten sulfur. If sufficient carbon disulfide is present, ignition of the vapor-air mixtures can occur spontaneously on contact with the heated surfaces found within storage tanks.

Jan 1, 1963

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By V. A. Marple, K. L. Rubow, B. A. Olson

"INTRODUCTION Inertial classification, gravitational sedimentation centrifugation, and thermal precipitation arc techniques that can be used to collect particles for subsequent analysis or for particle classification. The inertial classifiers, which include impactors, virtual impactors, and cyclones, are widely used in the sampling or particles. Settling chambers, which include centrifuges as well as gravitational settling devices, are less widely used. Thermal precipitators arc seldom used.Impactors, in particular, have been used extensively, studied both theoretically and experimentally, and arc the instrument or choice for the determination or aerosol mass size distributions. Many versions or impactors arc available commercially and many more have been designed, built, and used in special studies.Virtual impactors are a more recently developed inertial classifier and possess a feature not round in conventional inertial impactors; namely, that the particles remain airborne after classification compared to the conventional impactor, where the particles arc collected on a solid surface. The feature or keeping particles airborne is important for transporting the particles to other particle-analyzing instruments, or to filters, and in concentrating particles larger than the cutsize in a small fraction of the total now."

Nov 1, 1995

By A. E. Schwaneke

Plans and specifications are given for constructing a quartz composite oscillator designed to measure internal friction in metals and alloys . The characteristics of the system are listed , and detailed procedures for its operation are explained . Typical measurements on manganese - copper alloy , on single - crystal magnesium , and on polycrystalline magnesium are shown to illustrate applications of the system .

Jan 1, 1964

From 1886, the first year shipments were recorded, until 1939, the Leadville district produced over 3,500,000 long tons of manganiferous ore. Of this total, metallurgical-type ores comprised 27 percent and manganiferous iron ores suitable for fluxing in lead smelters made up 73 percent. In 1939, the Bureau of Mines, as part of the strategic minerals investigative program being conducted at the time, requested the Mineral Industries Survey Section of the Mining Division to make a comprehensive study of the manganese resources of the Leadville area. This investigation, owing to the caved and flooded condition of the underground mine workings, was necessarily confined to a study of old maps, production records, and geological reports, and the results were published as an Information Circular in July 1940.

Jan 1, 1949

By J. C. Duchon

The use of extended workdays or compressed workweeks (regular shift lengths exceeding 8 h) is attracting growing interest in many industries using continuous operations. While extended workdays promise increased worker satisfaction due to more days off, including weekends and holidays, there are legitimate concerns about the potential effects on the health and safety of such a schedule. The U.S. Bureau of Mines (USBM) conducted a study at a Canadian underground copper, lead, and zinc mining operation that was designed to study the safety and performance implications of extended workdays. Measures were taken before and after a change from the old 8-h continuous schedule to the new 12-h continuous schedule, including behavioral performance measures to analyze perceptual-motor changes, continuous heart-rate monitoring and aerobic capacity to measure physical fatigue, a variety of self-report questionnaires to measure perceived adaption and satisfaction with the new schedule, and pulmonary-respiratory measures to examine air contaminant exposure. Based upon the overall acceptance of the new schedule by the workers and lack of change in fatigue-sensitive behavioral and physiological performance measures, this study recommends that the mine retain the 12-h schedule. However, certain precautionary measures are suggested to insure the safety of the workers.

Jan 1, 2010

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928