Search Documents

By C. J. Walker, J. S. Miller

This work was done in an attempt to find a simple solution to the problem of simultaneously changing terminal rate and terminal pressure under conditions of unsteady - state flow in porous media . Although the original aim was not realized , a method for encasing a sandstone core that would permit high - pressure ( 200 to 980 psi ) flow tests and the use of electronic equipment to measure pressures at points along the core during unsteady - state gas depletion was found to be feasible . The sandstone core used in this study was from the Bandera formation of Pennsylvanian age , Redfield , Kans . The core , cylindrical in shape with a 3.5 - inch diameter and 6- foot length , had a porosity of 15 percent and a permeability of 9 millidarcys .

Jan 1, 1963

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result- ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coalbed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beck- ley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By F. E. Joyce

The Bureau of Mines studied copper-nickel minerals (mainly sulfides) of the Duluth Gabbro Complex in north-eastern Minnesota to determine their response to selective high-temperature sulfatization techniques. The gabbro, containing 0.44 percent copper and 0.13 percent nickel, was ground to minus 325 mesh and sulfatized in a heated, rotating, stainless steel bench-scale retort. Tests demonstrated that over 95 percent of the copper and 80 percent of the nickel can be converted to water-soluble sulfates, depending upon the roasting conditions employed. Yield equations were developed using regression analysis for predicting the extraction of copper and nickel between the temperature limits of 520° to 670° C, the roasting time limits of 3 to 7 hours, and S02 limits of 10 to 40 percent in S02-air mixtures.

Jan 1, 1971

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine vas evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, and a previously described/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming; and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive Physical and chemical apparatus. Following the termination of this study of chronic poisoning, possibilities ides for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals rich the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By Ernest W. Johnson

In most underground iron mines in the Lake Superior district the active workings are at considerable depth. When additional openings into such. nines are needed, operating officials are eager to discover more efficient methods of constructing them. In recent years, openings into two mines in the district were made by the borehole method,-which employs chilled-iron shot as the cutting medium. Others were made by the churn-drill method, in which pilot hole is churn-drilled and subsequently reamed to a desired but relatively small diameter. Both methods are comparatively new and unique, at least in some phases and in their application.

Jan 1, 1946

By K. C. Dean

During the investigations of the occurrence of manganese in the Western United States, a Bureau of Mines examining engineer collected samples frame two properties in Beaver County, Utah. As the ores were too low in grade to be acceptable by manufacturers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The Steelville property is about 37 miles southwest of Frisco, Utah. The deposit is an example of manganese occurring as a replacement of limestone in a bedded vein or as layers in limestone associated with shale and rock decomposition products. The Susie Q deposit, about 33 miles southwest of Milford, Utah, is also a tabular replacement deposit in limestone, apparently of limited extent. Test work was done on representative samples of 2-ton lots obtained by the examining 'engineer from each of the properties mentioned.

Jan 1, 1951

By Árpád B. Palotás, Adel F. Sarofim, John B. Vander Sande, Lenore Rainey Christian, J. Feldermann

"Interest in the fine structure of soots and carbon blacks is motivated by a variety of possible applications. The structure provides information on the origins of the particles and on their adsorptive and reactive properties. This paper describes a method for quantification of the structure of soots and carbon blacks based on direct electron microscopic observation followed by image analysis of these materials. High-resolution transmission electron microscopy (HRTEM) provides a very detailed observation of particle structure. The differences in soot structure, because of its complexity, may not be easily quantifiable with the human eye; therefore, high-level computer software has been used to manipulate HRTEM images. This technique involves the application of fast Fourier transforms (FFT) to single particles and the measurement of characteristic parameters such as interplanar spacings and crystallite sizes from these particles. The methodology and application of this characterization technique are presented here. Results are shown for dif¬ferent samples obtained from soot and carbon black particles selected to illustrate the capabilities of the methodology. Quantitative information can be obtained on structural characteristics, e.g., interplanar spacing, circularity, orientation, elongation, and length distribution of lattice fringes, as well as on the fractional coverage of the extracted pattern. c 1996 Wiley-Liss, Inc.This paper presents a combination of techniques for recognizing and classifying different carbonaceous materials, using their structural morphology. A new method to assess and quantify the parameters which define such structures is proposed and discussed. The technique is based on the use of HRTEM (high-resolution transmission electron microscopy) and computational image analysis.It is well-known that carbonaceous materials like graphite, soots, coals, cokes, chars, etc. possess characteristic structural appearances which can vary from mostly random or amorphous to a perfectly ordered graphitic crystalline structure (Buseck and Bo-Jun, 1985; Buseck et al., 1987). The carbon structure has been variously described as turbostratic (Oberlin, 1989) or as crumpled sheets (Rouzaud et al., 1991) to indicate that parallel layering, reminiscent of graphite, is observed over dimensions of nanometers, but that these planes or crystallites show disorder over larger scales. The degree of order of such structures is strongly dependent on the thermal treatment of the material as well as on the composition of the source of the carbonaceous material. The value of the electron microscope in studying the morphology of such materials has been well-established, and abundant information is available (Ishiguro et al., 1991; Lahaye and Prado, 1978; Buseck, 1992).The use of HRTEM has brought further insight into this matter. Qualitative assessment of the structural order of such materials has been attempted over a long period of time in order to differentiate between various sources or treatments. There is, to date, no successful method available for quantifying the structural characteristics of various carbonaceous materials. This paper presents a technique which is able to recognize dif-ferent materials and to quantify the structural parameters of those materials using HRTEM and computational image analysis, including pattern recognition techniques.In the case of perfectly ordered graphitic crystals, electron diffraction is widely used for obtaining details on structure. Analysis of diffraction patterns can reveal parameters such as interplanar spacing, d002, crystallite size along the c-axis, Lc, crystal size in the plane of the layers, L., mean number of crystallites, Nc, etc.Complicated electron microscopy methods such as defocusing, tilted illumination, axial illumination, etc., often have to be used in order to characterize complex materials such as randomly oriented crystals in soots and carbons. Obtaining the right fo"

Jan 1, 1998

By I. AITKENS

The precious stones rubies and sapphires are transparent varieties of the mineral corundum . Essentially they are aluminum oxide , but the aluminum is often replaced. by small amounts of chromium , titanium , or iron . The chromium is said to give a red color , titanium a blue , and iron a yellow . True rubies range from rose to a somewhat purplish red and are sometimes termed " oriental rubies " to distinguish them from spinel rubies , stones of inferior hardness , density , and value . " Oriental rubies " are very rare , and the so-called " pigeon's blood" variety is the most valuable . Sapphires normally range in color from palest blue to deepest indigo , but actually all precious varieties of corundum of any other color than red are called sapphires . The most esteemed tint is like that of the blue cornflower . Colorless corundum of gem quality is called white sapphire ; the yellow variety is described either as yellow or as golden sapphire ; and the pale pink is classed as pink sapphire . The word " oriental " is also used as a prefix in naming varieties of corumdum of less popular colors . For instance , oriental emerald is used for green corundum, oriental topaz for yellow , and oriental amethyst for violet to purple varieties . The chief physical characteristics of rubies and sapphires are hardness , adamantine luster , and moderately high specific gravity ( 3.9 to 4.1) . Next to the diamond, corundum is the hardest of all minerals ; in fact , the sapphire is number 9 on Moh's scale , ranking between the topaz and the diamond. Rubies crystallize in 6-sided prisms terminated by flat faces and other varieties of corundum with twelve inclined faces , six above and six below , meeting in a girdle . Corundum is doubly refractive , with a direction of single refraction running parallel to the edge of the prism . The refractive indexes are very constant, the ordinary index ranging from 1.766 to 1.774 and the extraordinary index from 1.757 to 1.765. The double refraction always remains the same.

Aug 1, 1931

By Benjamin W. Haynes

This research was conducted as part of the U.S. Department of the Interior, Bureau of Mines program to recover metals, glass, and a combustible fraction from municipal solid waste (MSW). The objective of this analytical study was to determine the concentration of antimony, arsenic, and mercury in samples taken from various sampling areas in the Bureau of Mines raw refuse recycling plant and to compare these values with those for coals used in the generation of electricity. To provide the necessary analytical data, sensitive reproducible ashing-chemical digestion-atomic absorption procedures were adapted from published procedures. It was determined that antimony and mercury concentrations in the combustible fraction of MSW are approximately an order of magnitude higher than those found in coals presently used for power generation;' the arsenic concentration is similar in both fuels.

Jan 1, 1978

By Lance R. Barron

The U.S. Bureau of Mines (USBM) conducted ground pressure analysis of a wide abutment-type chain pillar in a two-entry gate road of a Western U.S. coal mine with an extremely weak immediate roof. About 15 m of fragile, low-strength mudstone lies between the seam and the lowest competent roof member. Three-and two-entry gate road designs with several pillar sizes and various secondary support systems have been employed to improve tailgate-entry stability, with varying results. This report discusses gate road layout and performance and secondary support effectiveness. The results of the pillar pressure study are compared to pillar loading predicted by a widely used pillar design method and to similar studies in other mines. A stability evaluation of the most recent longwall headgate, using the USBM Analysis of Longwall Pillar Stability (ALPS) method, indicates marginal stability in first-panel mining and instability in second-panel mining. The ALPS method and the USBM Coal Mine Roof Rating system are used to evaluate tailgate-mining stability of the previous gate roads and to determine pillar and entry width and top coal thickness criteria for tailgate stability in future panels.

Jan 1, 2010

By J. H. Tylczak

The Bureau of Mines studied the effect of alloy additions on abrasive wear of low-alloy steels. A dry-sand, rubber-wheel abrasion test appa-ratus using ASTM G65-Sl procedure B was used for the abrasive wear tests. Eighty-six material heat-treatment combinations were abrasion tested. Results of these tests were analyzed statistically using regression analysis to see if additions of Cr, Mn, Mo, Ni, Si, AI, Cu, and S were significant in affecting the abrasive wear rate of low-alloy steels. Regression analysis was also used to confirm hardness and C affect on the abrasive wear rate of these steels. It was found that for all the steels taken as a group, increased amounts of Mn significantly reduced the wear rate, while increased amounts of Mo and S1 increased the wear rate. Analysis also confirmed previous research done by others, that increasing hardness and amounts of C reduced the wear rate. For the hardened steels taken as a class, only increasing amounts of C and Mn reduced the wear rate, while increases in Si increased the wear rate. In the class of unhardened steels, increases in C, Mn, and S re-duced the wear rate, whereas increases in Mo increased the wear rate. The steels with the best resistance to wear were two hardened experimen-tal steels similar to AISI 1055 and AISI 107S.

Jan 1, 1986

By W. T. Millar

Field reconnaissance and laboratory tests an clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By R. C. Hickman

"INTRODUCTION Marl, consisting of a bed of coarse shell conglomerate from 1 to 5 feet thick, occurs on the Chesapeake Corporation tract and Philbates properties in New Kent County, Va.Nine holes were drilled on these properties in February 1946. ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch.LOCATIONThe Chesapeake Corp. deposit is reached from West Point, Va., by driving west on State Route 33 to the junction of State Route 634, approximately 5 miles. Proceed southeast along State Route 634 about three-quarters of a mile, at which point an old longing road turns north along a ridge and leads to the marl outcrops about one-half mile distant. The Philbates property lies three-quarters of a mile farther west along State Route 33 from the junction with State Route 634. The property lies north of State Route 33 and east of State Route 623 (fig. 1). The marl deposits are on the north end of the farm. The Chesapeake Corp. tract comprises 174 acres and the Philbato property 58 acres."

Aug 1, 1947

By W. E. Anable

The Bureau of Mines researched methods for recovering copper from cyclone and electrostatic-precipitator dusts of primary copper smelters as part of its program to maximize minerals and metals recovery from primary and secondary domestic resources. Small-scale studies showed that use of 110 pct stoichiometric sulfur and 123 pct stoichiometric carbon, based on producing a 40-pct copper-iron matte, resulted in the recovery of 95 pct of the copper contained in the dust. Typical mattes contained less than 10 pct of the arsenic, 30 pct of the bismuth, and 45 pct of the antimony and tin contained in the dust. Matte was converted to blister copper by injecting up to 200 pct of the stoichiometric oxygen requirement over a period of 2 to 3 hours. Up to 76 pct of the copper contained in the dust was recovered as a crude blister copper containing about 2 pct arsenic, 0.5 pct antimony, and less than 0.1 pet bismuth and tin. A matte-white metal product resulted from carbothermically reducing dust with coal, lime, and silica. Up to 95 pct of the copper was recovered in the combined product.

Jan 1, 1981

By Perry G. Cotter

The objective of this investigation was to synthesize and investigate the properties of a high-temperature refractory material based on a combination of boron, silica, and magnesium. A magnesium-thermic reaction was used for the synthesis. X-ray examination of the product indicates that the crystalline portion of the composition is a combination of magnesium borides, magnesium silicate, and magnesium orthoborate. Chemical analysis of a representative sample shows, in weight-percent, boron 17.6, silicon 23.9, magnesium 17.8, and chromium 0.5. The balance is largely oxygen. The composition is resistant to high temperatures under oxidizing conditions and is stable in water, hydrochloric acid, and hydrogen. It has a low density (less than 3 grams per cubic centimeter) and a hardness value in the range of quartz. It has a melting point above 1,700° C. and can be hot-pressed to shape in the temperature range between 1,200° and 1,350° C. The properties described in this paper indicate that the material may have some uses as a high-temperature refractory, and because of its boron content it may have some value as a thermal-neutron-absorption material.

Jan 1, 1961

By R. Hogg, T. H. Dumm

"The mathematical treatments used in the evaluation of particle size distribution from pipet-withdrawal centrifuge data are reviewed. An error in the published procedure for multiple-sample withdrawal systems is pointed out and a corrected formulation is presented. An alternative treatment, based on a piece-wise linearization of the size distribution is described. Computer simulations of the analytical and data evaluation procedures indicate that the errors in the original formulation are not generally serious and that the corrected and alternative procedures lead to very similar estimates. Except for some cases involving very narrow size distributions, the alternative approach appears to give slightly closer estimates of the size distribution. Comparisons based on actual experimental data are also described.1 IntroductionSedimentation methods are widely used for the determination of particle size distributions. The procedures are relatively simple to use and the results are essentially absolute, requiring no external calibration. Gravity sedimentation is typically applicable to particles in the size range of about I to 50 pm and generally involves measurement of the relative concentration of particles as a function of depth and time in a dilute suspension. Particle size is calculated using Stokes, law:"

Mar 1, 1989

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

By Stephan Stecura

One of the principal objectives of the Bureau of Mines program for development of superrefractory ceramic materials is to obtain fundamental data on the physical properties of refractory oxides. Elements of particular interest to research workers in the Bureau include groups III and IV of the Periodic Table and the rare-earth group. This report contains thermal expansion and phase inversion measurements on oxides of scandium, yttrium, lanthanum and 12 lanthanide series elements (promethium and terbium omitted) up to 1,350°C, made by high-temperature X-ray diffractometer techniques. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures; with anisotropic oxides expansion was determined parallel to each major crystallographic axis. The combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C, and approximately 2 percent at 1,000° C, No difference in expansion coefficients was observed between heating and cooling cycles for oxides that did not undergo phase inversion. Tabular data of linear expansion, in percent, linear expansion coefficients, and graphical presentation of linear expansion as a function of temperature are presented.

Jan 1, 1961

By J. W. Town

The Bureau of Mines made continuous-circuit beneficiation studies to determine the optimum conditions for concentrating phosphate minerals from the intermediate-and marginal-grade ores of the Phosphoria Formation in southeast Idaho. Intermediate-grade ore was represented by a sample from Georgetown Canyon and marginal-grade ore from the Gay mine near Fort Hall. Two flow-sheets were developed: The first involved roasting, attrition scrubbing, sizing to remove a concentrate, grinding of the oversize, des liming, and flotation; in the other flowsheet roasting was eliminated. Controlled attrition scrubbing was used to remove clay and silt-size quartz particles imbedded in the phosphate pellets without breaking the pellets. The minus 35-plus 200-mesh fraction was removed by sizing as a finished acid-grade concentrate. The plus 35-mesh material was ground in a rodmill to minus 35 mesh and recycled to the attrition scrubber. The minus 200-mesh fraction was des limed at about 800 mesh to remove clay slimes and floated with 3 to 4 pounds of emulsion per ton of feed. The aqueous fatty-acid oil emulsion consisted by weight of 3 parts No.2 diesel oil, 3 parts crude tall oil, and 0.5 part water-soluble petroleum sulfonate.

Jan 1, 1967