Search Documents

By G. S. Knoke

This report presents the results of a demonstration of the technical, economic, and environmental feasibility of hydraulic borehole mining of shallow oil sands. Borehole mining offers a method for extracting the oil sands with minimal disturbance to environmental quality because (1) no overburden is removed, (2) no waste rock piles are required, (3) the tailings can be backfilled into the borehole cavity, (4) the ground water quality should be undisturbed, (5) a closed-loop water system can be employed so that no surface streams are polluted, and (6) surface subsidence can be minimized by backfilling the mined cavities. This project consisted of two concurrent tasks: mining operations and environmental monitoring. To generate the environmental impact, nearly 1000 tons of oil sands were mined from two boreholes. Water quality and ground subsidence were monitored. No significant changes occurred in the chemical composition of the process water, indicating that the borehole mining process does not dissolve the mined material. The average subsidence in the immediate vicinity of the boreholes was about 1/2 inch, although some points were noted to be slightly elevated. In general, the amount of subsidence increased with time and decreased with distance from the bore-hole. A mining cost analysis was used to project an estimated cost for production mining of about $38 per barrel of oil.

Jan 1, 1980

By Foster Fraas

This report describes the application of pulsed magnetic fields derived from alternating and intermittent magnetizing currents. Application of such pulsed magnetic fields to the matrix-type separator permits (1) the complete discharge of the magnetic fraction with wet feeds and (2) the dry separation at particle sizes down to 325 mesh. At smaller particle s indications are that frequencies above 60 hertz will be required. Applications of intermittent magnetizing current to the cross-belt separator give the cross-belt-separator an advantage over the conventional constant-field cross-belt and induced roll separators; the intermittent current enables the cross-belt separator to separate matted fibrous and magnetically coagulating feeds, a type of feed that occasionally occurs with mineral, industrial, and secondary materials.

Jan 1, 1973

By S. M. Shelton, J. B. Zadea, M. M. Fine, T. L. Johnston

"INTRODUCTION The Mayfield manganese property is about 25 miles south of Van Horn, in Jeff Davis County, Tex. The ore deposit is developed by a large open-cut and a small stope.An 8-ton sample was received for testing; it was taker at random from material on the mine dumps and consisted of a mixture of manganese oxides, barite, and siliceous gangue minerals. The manganese occurred largely as hard, massive, crystalline psilomelane, with a small amount of pyrolusite. The gangue minerals consisted of intermixed iron-stained sand stone, quartzite, chalcedony, calcite, quartz, and barite. Chemical analysis showed 8.9 percent manganese, 3.3 percent iron, 38.4 percent silica, 6.6 percent calcium carbonate, 7.1 percent barium, 3.1 percent alumina, 0.09 percent phosphorus 0.01 tungstic oxide, and less than 0.05 percentAnalysis of selected clean pieces of manganese minerals, free of gangue, showed 48.1 percent manganese end 13.4 percent barium, of which only 0.2 percent was present as barium sulfate. This indicated a limit in concentration. Barium was also present in the gangue as a separate mineral, barite (BaSO4), which has approximately the same specific gravity as the manganese oxide."

Apr 1, 1942

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba fields were studied]

Jan 1, 1941

By E. Morrice

This report of the Federal Bureau of Mines presents a laboratory procedure, with the requisite equipment, for electrowinning ingot (liquid) cerium metal from a fused-fluoride bath, the metal purity being about 99.9 percent. Physicochemical studies, including bath properties and electrochemistry, are included, with a speculative model of the mechanisms involved. An historical review of the methods used for electrowinning misch metals and yttrim-group metals, as well as individual rare-earth metals, is presented. The electrolytic preparation of metal from fused salt and nonaqueous media is summarized, along with the unsuccessful attempts at depositing the metals from aqueous solutions.

Jan 1, 1961

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Illinois using bucket wheel excavator (BWE) and a stripping shovel in tandem for overburden removal is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and scheduling problems and to generate and analyze alternatives for increased production. On the basis of the simulations it was concluded that the maximum productive capacity of the system in raw coal was around 3000 tons per shift. At this production level, the equipment combination and availability also satisfy the match requirements for the stripping shovel and the BWE, and the overburden and coal removal systems. Several alternatives requiring new equipment are proposed and analyzed for increasing production. However, no economic analyses of these proposals were done.

Jan 1, 1977

By Stella Sigler

This publication contains analyses and related source data for 153 natural gas samples from 16 States. Of the total samples, 149 were collected during calendar year 1993. The remainder were collected earlier, but releases granting permission to publish were not received until 1993. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of U.S. Department of the Interior, U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1994

By B. I. Ferber

Toxic and explosive atmospheres are discussed, along with some of the instruments commercially available for their detection. No attempt has been made to evaluate the accuracy of anyone device. This circular has been prepared primarily to aid mine inspectors in selecting suitable instruments for underground gas detection.

Jan 1, 1972

By H. Kenworthy

The purpose of the study described in this publication is to develop methods for recovering simple master alloys or single metal components from discarded and scrapped S-816 alloy, The Bureau of Mines started this investigation late in 1955 after the need became apparent for a method of reclaiming high-temperature alloys from an ever-increasing accumulation of rejected and wornout jet engine turbine buckets. Laboratory studies showed the following: (1) Pyrometallurgical separations are not selective enough, (2) several methods can be used for effective chemical dissolution of the major constituents of the alloy, (3) a master alloy or complex salts of cobalt and nickel can be separated, (4) chromium, contaminated by several other metals, may be segregated, and (5) more time and effort need to be expended in separating the minor constituents and improving the purity of the major metals removed. Difficult and incomplete chemical separations were attributed to the complexity of alloy composition, as were the long tedious chemical analyses o' products. For determination of several of the metallic components, standard methods of separation and routine analytical procedures had to be considerably modified to achieve satisfactory results. The overall technical problems involved in separating S-816 components do not appear to be insurmountable; however, refinement of several of the methods used in this investigation is desirable.

Jan 1, 1961

By C. R. Kuzell

This paper, describing the concentrator practice of the United Verde Copper Co., is one of a series being prepared by the Bureau of HISTORY The United Verde concentrator was constructed in accordance with recommendations based on certain novel reasons which were quite different from those usually justifying the expenditure of such an amount. Concentrator operations started in March, 1927, although the metallurgical staff had considered for several years the eventual addition of a concentrator department.

Jan 1, 1930

By Nabil A. Bibawy

An improved method for preparing gravimetric standard gas mixtures of helium-4 in nitrogen has been developed by the U.S. Bureau of Mines. A single-pan 12-kg analytical balance that has a sensitivity of 3 mg is used to prepare the mixture. The balance will accommodate a cylinder having a volume of approximately 4 L that weighs approximately 5 kg. The method has been improved to a precision of ±O.04 pct by performing four successive dilutions, by improved handling of gases in the manifold, and by using an improved analytical method to select high-purity gases.

Jan 1, 1990

By G. A. Smyres

The Bureau of Mines conducted laboratory studies to determine the feasibility of chlorine-oxygen leaching for treating low-grade zinc sul-fide flotation concentrates. Recovery of zinc sulfides by flotation from complex fine-grained sulfide ores is substantially higher in low-grade bulk sulfide concentrates than in the high-grade cleaned concen-trates required for smelter feed. However, there is no commercial process in the United States for the treatment of low-grade bulk zinc sul-fide concentrates. Leaching experiments using reactors of 500-mL and I-gal capacity were conducted on a bulk concentrate containing 19.3 pct Zn, 35.6 pct Fe, and 39.4 pct S. The effects of pressure, temperature, and percent solids on extraction were investigated. The chlorine-oxygen leaching procedure showed promise for treating the concentrates. Zinc extractions of 95 pct or more were obtained by leaching at 50 pct solids in the temperature range of 1000 to 1200 C. Zinc extractions by leaching with chlorine followed by oxygen at reactor pressures of 50 to 100 psig were independent of pressure.

Jan 1, 1985

By Michael Sokaski, M. R. Geer, H. F. Yancey

This report is one of a series describing investigations by the Federal Bureau of Mines of the performance of various types of coal - cleaning equipment ; other reports in the series are listed in the bibliography . The information in these reports is useful to the coal industry and the manufacturers of coal - cleaning equipment in several ways : First , it assists the coalpreparation engineer who is planning a new plant to select the type of process best suited to the requirements by enabling him to forecast the yield and quality of clean coal obtainable with each type of equipment . Second , the information serves as a yardstick by which the performance of a plant can be judged and thus helps determine whether it is operating at satisfactory efficiency . Both these functions promote better coal - preparation practice ; that is , they help provide coal of more suitable quality for the market and likewise minimize the waste of good coal . This serves the interest of conservation with which the Bureau is vitally concerned . The present report deals with three plants using the Tromp dense - medium process , named after its inventor , K. F. Tromp , who developed the process in the Netherlands in 1936.5/ Selection of this particular dense -medium process for investigation was entirely a matter of convenience , and reports dealing with other dense -medium systems are planned for the future . Two baths are employed in one of the plants investigated . The first of these , handling 6- to 3 - inch coal , exhibited an exceptionally sharp separation between coal and impurity . This was characterized by an error area of 12 and a probable error of 0.023 . In the second bath , treating refuse from the

Jul 1, 1960

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By R. V. Ramani, P. M. T. White, D. Sutton

Appendix I. Part 1: Description Of Geology & Reserves System Introduction The Ore Evaluation and Reserve programs have been developed to aid in the evaluation of coal deposits, both qualitatively and quantitatively. The "Weighted Moving Average" technique used provides considerable flexibility in dealing with diverse parameters with differing distribution characteristics. Determination of Model Constants "a" and "k" - Unit 1 The flexibility of the method in dealing with diverse value parameter distributions lies in its ability to cater to the individual characteristics of each. These characteristics are embodied in the values determined for constants "a" and "k", namely, local and regional variations in value distributions, respectively. The empirical method used attempts to optimize the "a" - "k" combination. Realistic values for "a" and "k" are entered into the program together with sample values for the required parameters and their respective coordinate location values. All the values within a specified radius from the point being evaluated are used to interpolate a value at that point. (Note, the interpolated point is the location of one of the boreholes, values of which are not used in the calcula¬tion.) 3n a similar manner, interpolated values are calculated for each borehole location and for each parameter. This is done for each possible combination of "a" and "k".

Jan 1, 1974

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-l Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By Irving Kabik

Chlorates and perchlorates, when mixed with certain reducing materials, may give a detonating explosive of considerable power. Concerning explosive chlorate mixtures, Guttman3/ states that they "have at all times fascinated inventors on account of the large amount of oxygen stored up in potassium chlorate, which can be given off so readily. When Lavoiser and Berthollet tried to make a chlorate powder in a stamp mill in 1788, they made a great show of it, and even two ladies were present. Unfortunately, after a certain amount of pounding the powder exploded and killed an official and the daughter of the Government commissary, who assisted at the experiments.***. It is interesting to observe how the same old mixtures are proposed over and over again with slight alterations only, in order to qualify for a patent. Potassium chlorate with some carbonaceous matter like charcoal, sugar, starch, glycerin, flour, or sometimes a vegetable or mineral oil and the like occurs again and again." Sprengel explosives, in which some of the undesirable sensitivity of the chlorate was minimized by coating the crystals with a liquid reducing agent, received some attention after a patent was issued to Dr. Herman Sprengel in England in 1871.4/ A somewhat similar explosive, known as Rack-a-

Jan 1, 1945

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976