Search Documents

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller: Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer's deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone. Another example of the waste of large volumes of gas is in the Turner Valley field of Canada, 6 where 250,000,000 cubic feet of gas is being burned daily in flambeaus, as there is no present outlet except at prohibitive cost.

Jan 1, 1931

By E. C. Lane

"INTRODUCTION The first important discovery of petroleum in New Mexico was near Dayton, Eddy County, where the Brown well was drilled in 1909, and small quantities of oil were produced. In 1911 and 1912 wells were drilled in McKinley County, but commercial production did not begin until the discovery of the Hogback field, San Juan County, in 1922. The discovery well in the Artesia field, Eddy County, drilled in 1923, gave impetus to active drilling in many areas. Since 1924 New Mexico has produced petroleum in commercial quantities and since 1930 the State has joined the ranks of the big produc¬ing States, being sixth or seventh in total production in recent years.Production by years. 1924 to 1940, inclusive, taken from annual figures in Bureau of Mines Minerals Yearbook, are given in table 1. The total production shown is 274,331,000 barrels. Andreas 3/ has published production figures for the year 1940 and a resume of all production to the end of 1940. Data from his report are presented in table 2 for each field sampled. The cumulative production, as given by Andreas, is 270,618,575 barrels."

Aug 1, 1942

By Eric E. Cather

A mineral survey of a portion of the Lake Eleanor RARE II area (No. 5807), Trinity County, California, was done by the U.S. Bureau of Mines and U.S. Geological Survey (USGS). Approximately 8,650 acres (3,500 ha) of the Lake Eleanor RARE II area not examined for this report had been previously investigated by U.S. Bureau of Mines and U.S. Geological Survey personnel and published as part of USGS Bulletin 1371-B, (Hotz, 1972) Mineral Resources of the Salmon-Trinity Alps Primitive Area, California. The report showed that the section included in the rake Eleanor RARE II area contained no metallic mineral resources. Geochemical sampling indicated that the Lake Eleanor RARE II area contains no potentially important mineral resources. About 4,650 acres (1,880 ha) of the eastern part of Lake Eleanor RARE II area were examined for this report. The Bureau of Mines was responsible for detailed examination and sampling of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. This area is underlain mainly by granitic rock and serpentinite.

Jan 1, 1981

The XVIth International Conference on Coal Mine Safety Research was divided into eight half-day technical sessions. In accord with the established practice of these conferences, at each session, presentation of the papers was followed by a discussion period. Questions and comments submitted in writing to the session chairman were answered or discussed by the authors of the relevant papers or by their representatives. These discussions were tape-recorded in the original language of the speaker and subsequently translated into English when necessary. Questions to which no answer was available at the time and a few comments that exceeded the scope of the session have been omitted.

Jan 1, 1975

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

"For a good many years the Bureau of Mines and various state mining experi¬ment stations have endeavored to develop some method of utilizing the immense deposits of lignite in the United States. Work in relent year has indicated that the best method of this is to drive off the moisture and most of the volatile water from the lignite in some form of carbonizing apparatus leaving a residue high in fixed carbon and low in moisture and volatile matter, which by briquetting can be made into a high-grade fuel. The earlier forms of carbonizing equipment tried were complicated, costly to build and keep in repair, and could not be operated intermittently without being seriously damaged. During the year 1922, however the Bureau of Mines devised a very simple carbonizing oven which produces a uniformly well carbonized product. This oven is essentially a vertical shaft with means for supplying raw lignite at the top and discharging the carbonized limited at the lower end. Air in regulated amount is admitted to the shaft at two horizons, and a zone of combustion maintained through which the column of lignite passes. The lignite is thus carbonized by construction of its contained matter and a small proportion of its fixed carbon, leaving most of the fixed carbon in the carbonized product or ""char"". The degree of carbonization can be closely controlled by varying the volume of air supplied to the oven and the rate of travel of the charre down the shaft.The ""lignite char"" produced is a soft material resembling charcoal more than coal or coke, but somewhat harder than charcoal. A typical analysis is shown in the table headed ""Fuels,"" further on in this papers."

Feb 1, 1924

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

By Donald O. Capstick

A mineral resource evaluation of the Coyote-Southeast RARE II area (No. 5033) was performed jointly by the U.S. Bureau of Mines and the U.S. Geological Survey in 1981 for the U.S. Forest Service RARE II program. Bureau of Mines personnel conducted a mineral resource inventory of the study area's mines, prospects, claims, and mineralized outcrops. The study area's boundaries encompass 51,700 acres on the east flank of the Sierra Nevada and are within Inyo National Forest southeast of the city of Bishop in east-central California. Cretaceous granite underlies most of the area; the remainder of the rocks are metasedimentary. At the contact of the two, tactites formed at many places where carbonate rocks were present; replacement processes produced local scheelite (calcium tungstate) occurrences.

Jan 1, 1983

By D. R. Babich, E. R. Bauer

Noise-induced hearing loss (NIHL) in mine workers, especially underground coal miners, continues to be a problem in the mining industry. The recently enacted MSHA noise standard, Part 62 – Occupational Noise Exposure (Federal Register, 1999), is aimed at reducing NIHL in the mining industry. The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures to address NIHL in various aspects of coal mining including surface mining, coal preparation plants and underground mining. In underground bituminous coal mining, noise surveys, consisting of full-shift worker noise exposure, time-motion studies and equipment noise profiling, have been completed on longwall and continuous miner sections in six underground coal mines. The studies revealed widely varying shift-to-shift worker exposures, with workers in certain occupations routinely exposed to potentially hazardous levels of noise. A summary of these studies is reported, including worker dose, source/dose relationships and equipment noise profiles.

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By D. W. Bridges, L. Crocker, R. O. Dannenberg

About 95 pct of the beryllium was dissolved from most ore samples by agitation leaching with 600 lb of H2SO4 per ton of ore for 24 hours at 65 ° C and 35 pct solids . Leach slurries generally were viscous , and the limiting pulp density for thorough mixing was about 35 pct solids . Settling of the leached pulp required 0.6 to 0.8 lb of a polyacrylic flocculant per ton of ore leached with 600 lb of H2SO4 per ton , whereas ore leached with 800 lb of H2SO4 per ton required only 0.2 to 0.3 lb of flocculant per ton . Terminal densities of the settled pulps were about 28 and 35 pct solids , respectively , from leaches using 600 and 800 lb of H2SO4 per ton . Vacuum filtration of settled pulps at 15 in . Hg resulted in a filter cake containing 50 to 59 pct solids . Roasting the ore at 500 ° C before leaching increased the limiting pulp density for effective mixing to 50 pct solids . Acid requirements , however , were not diminished , although leaching roasted ore with 600 lb of H2SO4 per ton resulted in densification of settled pulps to about 40 pct solids . Filter cake from leaching preroasted ore contained about 20 pct less water than that from unroasted ore .

Jan 1, 1963

By Robert C. Johnson

Water-swelling fluormicas and fluormontmorillonoids were synthesized and described. They were found predominantly in the system Mg0 - MgF2 - Si02, with varying amounts of Li+ or Na+, Some water-swelling synthetic minerals were prepared with only strontium or lead in the twelvefold position, Water- swelling compounds containing either K+ or Ba+ were not found. The synthesized water-swelling products were shown by electron microscopy, X-ray diffraction, and chemical analysis to be typically two-silica-layer, platy compounds, Except for the complete substitution of fluoride for hydroxyl, the compounds were similar to the natural micas or montmorillonites. The stability and properties of the compounds were further established by electrodialysis, by differential thermal analysis, and by anion and cation exchange methods. Fluoride in the interlayer positions was nonexchangeable except through decomposition of the product. Exchanging the sodium or the lithium of the synthetic fluormicas or fluormontmorillonoids with potassium ion, particularly those derived from KOH provided a product from which a completely inorganic paper of extraordinary flexibility was fabricated. This paper had excellent mechanical and electrical properties except for water adsorption and a high power factor. Neither of these problems was solved during this investigation. However, papers with dielectric strength from 1,500 to 5,000 volts per mil were readily fabricated, particularly from the lithium containing fluormicas or fluormontmorill onoids.

Jan 1, 1963

By Jack Wright

The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines5-8 and Federal Geological Survey,9-11/ as well as articles in engineer and geological journals12-14/ placed special emphasis on the importance, interpretation, and application of water analyses. One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for Analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, "In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .," and, "The waters of each oil field are chemically different from those of another field." The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the a geological formation in different localities or oil pools.

Jan 1, 1957

By Rustu S. Kalyoncu

A major goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. In support of this mission, a survey of the state of the art of chemically bonded refractories has been made, covering the scientific literature, government reports, and patents. This review includes research and development results for phosphate, silicate, oxychloride, oxysulfate, and other bonding agents used in refractories manufacture. A significant finding of the review was that references on bonding mechanisms, bond formation kinetics, and other important process parameters and conditions were few and universally vague. As a result, recommendations are made to expand research efforts to investigate the kinetics and mechanisms of reactions in chemically bonded refractories.

Jan 1, 1982

By W. J. Kroll

This report on the bibliography of zirconium has been confined to those publications and patents that appear to be useful in the commercial development of the metal, both the malleable and the nonmalleable. The methods of production have been stressed and special attention has been given to the alloys. Compounds of importance, like the oxide and chloride, for the manufacture of the metal or of the alloys have been considered. The use of the oxide in refractories anal in the glass and porcelain industries has been omitted. The present survey is critical; that is to say, an attempt has been made to evaluate the effectiveness of suggestions made in the literature. The exhaustive work of Marden and Richy, Bureau of Mines Bulletin 186, published in 1921, has been taken as a base to start from with the intention of bringing the subject up to date with material published in the last 24 years. During this time there was considerable 'advance in the preparation of the metal and Its alloys, and in the development of new uses. On the other hand, there was little progress in the methods of decomposing the ores, so that the chapter on this latter phase is necessarily short.

Jan 1, 1946

By John Durkin

This report discusses the configuration and system deployment for the postdisaster surface seismic system for detecting and locating trapped miners. It analyzes the results of 15 field tests to define a signal model, background noise levels, and subarray performance. A waveform modeling procedure is described and compared with observed waveforms. The resulting similarity indicates that the major factors affecting the signal amplitude, waveform, and spectral character are understood. A model is presented which gives the sig-nal amplitude as a function of source type, source depth, and horizontal off-set between source and receiver. Using this model a curve is presented which gives the range at which a signal will be detected for different signal and noise levels. Finally, and most important relative to the mission of the system, the ability of the system to detect signals on one or more subarrays is put into a probabilistic framework. For a strong source it is almost certain that a subarray directly over the source will detect the signal. After signal processing, it is highly likely that signals will be detected on sufficient subarrays to locate the trapped miner. Location errors have been found to be less than 100 ft in the majority of cases. Techniques have been used that can reduce the location errors to this level even when soil layer variation between subarrays is severe.

Jan 1, 1981

By J. M. West

Expanded war in Viet-Nam overshadowed activities in the Far East in 1965, diverting capital and materials from potential regional development projects. Japan with-stood a period of business recession that was particularly felt by its coal mining and iron and steel industries. Toward yearend signs of improvement began to show. Despite the recession with attendant credit restrictions and forced cutbacks in areas of overproduction, Japan's overall industrial output rose nearly 5 percent during the year. Foreign trade, liberalized in 1964, was a strong point in the Japanese economy and took the place of lagging domestic demand. Japan maintained its third place in world production of iron and steel ahead of West Germany and in 1965 was the world's fore-most exporter of iron and steel in primary and semimanufactured forms. Economic setbacks in mainland China caused by its "Great Leap" failures and subsequent withdrawal of Soviet technical assistance were difficulties relegated to the past. However, a newly formed "Red Guard" political group, part of a so-called cultural revolution, was due to cause new disruptions in 1966. Nevertheless, significant gains were claimed in Chinese industry, and the country approached self-sufficiency in petroleum in 1965 by virtue of its Tach'ing oilfield. Restoration of friendly relations was achieved between South Korea and Japan accompanied by Japanese offers of industrial aid and increased trade. Indonesia's economy was deteriorating; the country withdrew from regional development organizations and continued its stubborn confrontation policy against Malaysia throughout 1965. Late in the year after a Communist uprising had been quelled, there was a period of political retrenchme t and it was hoped that economic improvements would follow. Petroleum remained a strong area in Indonesia's varied resources, and its production was increasing. Tin output declined, however, because of operating difficulties.

Jan 1, 1967

By J. F. Barkley

Under the procedure of the American Standards Association, with the American Society for Testing Materials as sponsor, the Sectional Committee on Classification of Coals has arrived at the classification of coals by rank as shown in Table 14/. The standard explains the term "agglomerating" used for classification under physical properties, as follows: Agglomerating Index. - Coals which in the volatile-matter determination produce either an agglomerate button that will support a 500-g weight without pulverizing, or a button showing swelling or cell structure, shall be considered agglomerating from the standpoint of classification.***. Pending the adoption of a method by the American Society for Testing Materials, the coke-button grading test5,/ afforded by the examination of the residue in the platinum crucible incident to the volatile matter determination, shall be used.

Jan 1, 1937

By Michael D. Balen

The U.S. Bureau of Mines (Bureau) is currently conducting a four-year study to assess the mineral resources and the mineral development potential of the 5.7 million acre Valdez Creek Mining District (VCMD) located in southcentral Alaska. The VCMD study is part of the Bureau's ongoing statewide mining district evaluation program. This report is a summary of the 1988 field work. The field work involved collection of reconnaissance placer and rock samples, and also involved sampling and examination of the mines, prospects, and mineral occurrences which were identified by literature research of the geology, exploration history, and mining history of the district. During the 1988 field season, Bureau personnel spent a total of 11 weeks in the field, collected 1,006 rock and placer samples, and located, mapped, and sampled 106 of the known mineral occurrences. The Bureau has visited 243 of the 250 known mineral occurrences during the course of the VCMD project. Reconnaissance sampling for placer occurrences resulted in the identification of 4 previously unreported gold placer occurrences, and identification of 5 occurrences that contain detectable levels of platinum or palladium. Reconnaissance sampling for lode sources of base and precious metals resulted in the identification of 5 new Lode gold-silver occurrences, identification of 2 occurrences that contain elevated quantities of chromium, cobalt, nickel, palladium, and platinum, and identification of one occurrence that contains elevated quantities of copper, molybdenum, anti zinc.

Jan 1, 2011

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959