Search Documents

By Lowell Stroud

A windowed-cell phase equilibrium apparatus was used to obtain equilibrium vapor- liquid data for a helium-bearing natural gas (Hogback) at temperatures from -100 to -250° F and pressures to 500 psia. Anomalous phase behavior resulting in the formation of two stable liquid phases occurred at tmperatures below -200° F and pressures above 200 psia. A review of the published literature on the occurrence of multiple-liquid phases included in the report indicates that the experimental results with Hogback gas are the first substantiated evidence of a vapor-liquid-liquid equilibria in a helium-containing natural gas.

Jan 1, 1963

By R. C. Buehl

A pyrometallurgical process for recovering manganese from open-hearth furnace slags or low-grade manganiferous iron ores is described. The slag or ore is smelted in a blast furnace to produce spiegeleisen; the speigeleisen is then blown with air in a basic converter to give an oxide slag. This slag product contains 60 to 75 percent manganous oxide and may be considered a synthetic manganese ore. In the smelting operations coke rates for five test periods ranged from 3,255 to 4,130 lb per ton of spiegeleisen. The recovery of manganese in the spiegeleisen varied from 60 to 76 percent. Recovery increased to 83 percent when the open-hearth slag feed to the blast furnace was diluted with a high-? grade iron ore sinter to facilitate smelting. In blowing the spiegeleisen a cyclic procedure was developed that gave nearly 90 percent recovery of manganese in the slag product (synthetic ore) yet prevented excessive contamination of the slag by phosphorus and iron. The overall recovery of manganese was about 75 percent when iron ore sinter was used with the open-hearth slag in the smelting step. The metal remaining after oxidizing the manganese from the spiegeleisen contained approximately 3.5 percent phosphorus. It was refined in a basic converter by blowing with air in the presence of lime" A high--grade iron and a basic phosphate slag were produced.

Jan 1, 1965

By Richard P. Walters

This Bureau of Mines report reviews and assesses the technology for preparing electrodeposited coatings of the platinum-group metals from molten alkali metal cyanide baths. Methods are described for the preparation and purification of the cyanide electrolyte. Vacuum drying, fusion, and purity of the cyanide salts are discussed. Use of a sodium borosilicate test tube as a sodium-ion-conducting membrane for the addition of the desired platinum-group metal is described. The optimum plating parameters of potential and current density for Pt, Pd, Rh, Ru, and Ir coatings that result in the best deposits are given. A method for producing platinum-rhodium alloy coatings of predetermined composition is also described. The importance of careful substrate surface preparation is illustrated. While problems still remain with respect to coating porosity, careful application of the methods described permits the preparation of adherent, coherent electrodeposited coatings of the platinum-group metals.

Jan 1, 1984

By G. W. Weems

The Bureau of Mines used the Burnett method and apparatus to determine the compressibility factors for helium and carbon dioxide mixtures at 0°, 10°, 20°, 23°, and 35° C and to pressures of 900 psia. Tables of compressibility factors and approximations of the virial coefficients are presented for seven binary mixtures as well as for helium and carbon dioxide. The results compare favorably with existing data.

Jan 1, 1969

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

By Frank C. Morris

This report presents the results of a Bureau of Mines study to identify clays found in several petroleum-reservoir rocks in the Tejon-Grapevine area, Kern County, Calif., and to determine the effect of water sensitivity of the clays on the permeability of the reservoir rocks. The clays in the porous rocks were examined in detail, and the clay-mineral types were identified by differential thermal analysis, X-ray diffraction, and optical and dye-staining methods. Fresh-water damage to the permeability of the oil-reservoir rocks was indicated by a study of 125 core samples from productive formations. The study indicated that, although clays were generally less than 5 percent of the reservoir rocks, they swelled in water, particularly fresh water, and nearly blocked the flow channels through which oil flows to the well, effectively reducing the permeability of the formations. The average permeability of rock decreased from 1,600 millidarcys in air to 620 millidarcys in salt water and 120 millidarcys in fresh water. The dominant clays in the oil-bearing sandstones were members of the montmorillonite group. They were associated with smaller quantities of clays found to be in the mica or illite group. None of the cores appeared to contain clays of the kaolinite group. In the lower section of the J.V. sandstone indications of what appeared to be the mineral sepiolite were noted.

Jan 1, 1959

By A. E. Ketler

The Bureau of Mines Research Program has defined per coal miner's illumination needs. Due to similarity in the environment in which coal and Hardrock miners work, coal mine illumination technology has been applied to Hardtack room and pillar mines.

Jan 1, 1977

By Maria I. De Rosa

Analysis of mining equipment fires from 1990 through 1999 reveals that there were 340 large mining equipment fires, resulting in 72 injuries and five fatalities. Many of the fires resulted in the loss of equipment and all posed potential or real risks to the operator. In 97 cases, the fires raged out of control due to engine shut­off failure, even upon activation of the machine fire suppression system, due to the spraying of pressurized hydraulic flu­id and fuel onto hot engine surfaces. In other cases, even after engine shutoff, the fires re-ignited, fueled by the contin­ued flow of flammable fluids remaining in the lines onto the hot engine surfaces. In many of the fires, flammable vapors evolved and penetrated the cab, violently igniting, forcing the operator to exit under very hazardous conditions. The use of emergency evacuation lines in the fuel and hydraulic fluid systems, and methods to reduce or prevent the spraying of pressurized fluids onto hot engine surfaces would greatly improve the chances of successfully suppressing large mining equipment fires. In addition, the use of systems for preventing the ignition of flammable vapors inside the cab, and detecting and suppressing fires originat­ing in the cab, would greatly enhance operator safety. The National Institute for Occupation Safety and Health (NIOSH) recently conducted experiments on meth­ods to reduce the fire hazards associated with large mining equipment. These experiments evaluated the use of cab inerting systems to prevent the ignition of flammable vapors inside the cab and sup­press fires originating in the cab, while maintaining a breathable atmosphere for the operator to bring the equipment to a stop and safely exit the cab.

Jan 1, 2008

By William M. Thornton

[Owing to the comparatively high freezing point of nitroglycerin (14, 15, 16, 17, 18, 23, 37, 38)3/ - 1.9° C. and 13.0° C. for the labile and stabile modifications, respectively, as determined by Hibbert (16) - manufacturers of dynamites have incorporated into the liquid portion of these composite explosives various substances capable of participating in an explosion, to depress the above-mentioned freezing point. Aromatic nitro-compounds, chiefly nitrobenzenes, nitrotoluenes, and nitronaphthalenes, have been used to a considerable extent (11), but such nitrosubstitution products have not proved altogether satisfactory, as has been shown clearly by Naoúm. (14). Consequently there has been a strong tendency in recent years to replace them with one or more of several nitric esters, among which the following (29, 35) have been prominent: Dinitrochlorhydrin (monochlorhydrin dinitrate); nitrosugars, for example, sucrose octanitrate (19); tetranitrodiglycerin (diglycerin tetranitrate); nitroglycol (ethyleneglycol dinitrate); and diethyleneglycol dinitrate (13, 46, 47). Of these, nitroglycol (33, 4l, 45, 48, 49, 65) is outstanding in importance. As the Bureau of fines is naturally interested in the analytical chemistry of the "explosive oils," it seemed desirable to bring together in this report the widely scattered experimental work covering the problem of differentiation that has appeared in various chemical and physicochemical publications.]

Jan 1, 1941

By Gregory Molinda

NIOSH has recently completed a study of the interaction between polyurethane (PUR) and coal mine roof in order to determine the mechanism of reinforcement, in both highly fractured rock and unfractured rock. Four case studies of PUR rein­forcement are presented. At a West Virginia site, a borehole camera revealed the location of roof voids and guided the PUR injection. By injecting polyure­thane into a zone from 0.6 to 1.8 m (2?6 ft.) high in the roof, a roof beam was created and ongoing intersection falls were halted. In another highly fractured roof in a western Pennsylvania mine, a total of 5.8 cm (2.3 in.) of rubbleized rock was found in a zone up to 3 m (10 ft.) into the roof. Untargeted PUR injection filled approximately 1/2 of the fractures. These two case studies showed that it is not necessary to fill up 100% of the void space to create stability. In the other two field sites, polyurethane was injected into weak, but unfractured roof. Post-injec­tion video monitoring showed that weak bedding planes were hydraulically wedged open and polyure­thane injected along bedding. The reinforcement value of this injection method is limited because of the wafer-thin layer of PUR introduced along bedding, and the lack of a PUR ??webbing?? which would serve as a structural framework to provide strength. It was determined that video inspection prior to PUR injection can aid in identifying the fracture zones to target, and minimize ??blind?? pumping and loss of PUR.

Jan 1, 2008

By V. F. Parry

The major industrial uses of char or semicoke produced by low-temperature carbonization of coal4/ are as fuel for generating electric power, for blending with metallurgical coking coal as a substitute for low-volatile coals, and for gasification to produce synthesis gas for chemical purposes. This paper discusses various methods for carbonizing coal, emphasizing processing of the noncoking coals to produce char for thermal power-plant fuel and for blending with metallurgical coking coals and tar for chemical use. Low-temperature carbonization is a relatively simple processing step involving heating coal to about 900° to 1,200° F. to decompose the coal into 4 main products: (1) Semicoke or char; (2) complex, partly oxygenated liquid hydrocarbons or tar; (3) fixed gases; and (4) water. If the coal is heated rapidly under conditions that prevent decomposition of the primary products, 68 to 87 percent of the net heat in the raw coal is left in the char and 10 to 23 percent of the potential heat appears in the primary tar. Fixed gases represent approximately 7 percent of the heat and approximately 2 percent is lost or dissipated in the reactions of decomposition. Considering the different ranks of coal in the United States, the yield of tar will vary from about 9 to 44 gallons per ton, therefore it is important that each coal be carefully considered if it is to be carbonized for industrial use.

Jan 1, 1955

These inspection standard have been prepared for use in the Federal inspection of strip mines producing, bituminous coal, anthracite, and lignite. This circular is a revision of the Safety Code for Strip Mining, which was prepared by the Bureau of Mines and employed as a guide for Federal inspectors. Numerous changes have been made in the original code to keep the in step with improvements in the industry. With continuing changes in mining methods and facilities some of these standards may become inapplicable and further revision may be advisable. Therefore, questions regarding these standards, and suggestions regarding new standards should be brought to the attention of the Bureau of Mines. Few States haves laws pertaining to strip mines, but where such laws do exist it is possible that some of the standards may conflict with them. In cases of conflict, the intent is not to advocate noncompliance with State laws, but to suggest reconsideration of such laws or safety orders.

Jan 1, 1946

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By Raghoottma S. Pandurangi, Mohindar S. Seehra, Pedro Bolsait, Bronwyn L. Razzaboni

"Surface IR (infrared) modes of crystalline and fumed (amorphous) silica particles, calcined at temperatures up to 1095°C, have been studied by Fourier transform infrared spectroscopy. The ability of these same particles to lyse cells has been measured by a hemolysis protocol. The untreated crystalline and amorphous materials differ by a factor of 40 in specific surface area, and the intensity per unit mass of the sharp surface silanol band near 3745 cm-1 in the amorphous material is an order of magnitude larger than in the crystalline material. A similar difference is observed in the lysing potential of the two materials. The intensity of the silanol band increases after calcination for both materials, reaching peak values near 500°C, followed by a dramatic drop at higher calcination temperatures, and reaching negligible values for materials calcined near 1100°C. The lysing potential data follow essentially the same pattern for both crystalline and fumed silica. These results are consistent with the hypothesis that the surface silanol groups are involved in cell lysis. Further experiments are suggested to evaluate the relationship between the surface structure of ailica particles and their potential cytotoxicity. IntroductionThe characterization of the surface structure of various allotropic forms of silica is of interest because the cytotoxicity of silica particles of respirable size has been commonly related to the chemical interaction of functional groups on the surface of such particles with the lipoproteins contained in cell membranes (1-3). It has been found that the cytotoxic potential of silica particles varies greatly with their crystalline structure (4,5), particle size (6-8), surface composition (9), and molecular surface configuration (1,10). Studies of the infrared (IR) modes of various forms of silica have been reported by a number of researchers (3 ,11-19). Several books and reviews (20-24) have dealt with the identification of functional groups on silica surfaces and the effect of heat treatment on the surface structure. The nature of the surface is said to be critical in determining the biological activity of silica dusts (3).Fourier transform infrared (FTIR) spectroscopy is a highly sensitive ·technique for identifying IR surface modes of tine particulates, and it was deemed of interest to examine the surface structure and its relation to lysing potential of two widely different types of respirable silica dust. The lysing potential of respirable dust particles has been considered a first-level test for potential cytotoxicity."

Jan 1, 1990

By William Y. Mo

This report presents preliminary results of a study undertaken to investigate quantitative characteristics of the demand for steel mill products and its major end-use components. The major end uses included in the study are the steel mill products used in construction, in automobiles, in producer durables, and in consumer durables. The main objectives of the research underlying this study are as follows: (1) To formulate and estimate the empirical demand relations for steel and the four major end uses in the United States; (2) to measure and calculate the responsiveness of the U.S. per capita steel consumption with respect to the changes of the steel and other nonferrous metals prices; (3) to determine and quantify the relative importance of the underlying demand explanatory factors in contributing to the average year-to-year increases (or decreases) of the U.S. per capita steel consumption; and (4) to adapt and use the estimated demand relations in making projections of the U.S. future demand for steel and the major end-use components. After extensive preliminary investigation, three versions of simple linear demand relations are selected and estimated by means of ordinary least squares (OLS) method. The annual data for the period 1947-65 are used in the estimation. Direct and cross price elasticities of demand are computed for each of major end uses. The relative importance of demand explanatory factors in contributing to the average year-to-year changes of U.S. per capita steel consumption are also calculated. For making projections, a simple autoregressive time trend model is used in estimating the future values of independent variables. Since the estimated demand relations are valid for projections only if the estimated parameters can be assumed to be unchanged in the future, and consequently, the projections derived in the study should be interpreted accordingly.

Jan 1, 1970

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part 1 of the report contains the results of the field tests. The studies were made on an oil lease in a so-called "sour district," near Borger, Tex., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field test proved that aluminum lease tanks will withstand corrosion by hydrosulphide, but it as found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By J. F. McIlwain

Cobalt-base hardfacing alloys used for wear resistance consist almost entirely of metals largely imported into the United States. As part of an overall research program to help alleviate this foreign dependency, the Bureau of Mines has been investigating an iron-base alloy system as a potential replacement for cobalt-base alloys for some uses. To ascertain the melting ranges, thermal analyses were made of cast heats of alloys containing, in weight percent, 59-61 Fe, 16-19 Cr, 8-9 Ni, 1 Mn, 1 W, 1 Mo, 0.5 Cb, 0.6 Si, 0.3 C, and 0-12 stoichiometric TiB2. Powder alloys within this range of composition, prepared by mechanical alloying, were sized and applied to mild steel test coupons by nontrans-ferred-arc plasma spraying. The resulting thin coatings were >95 pet dense, with bond strengths of 35 MPa and hardness of 400 to 840 DPH. Abrasive and adhesive wear test data were compared to those of a plasma-sprayed cobalt-base alloy. A range of boride contents resulting in most promising properties was determined for further research.

Jan 1, 1985

By William E. Eckard

Production of oil from a narrow shoestring sand presents problems unique in the oil industry. Especially important, from both an engineering end an economic standpoint, are the limitations imposed upon well patterns and spacings by the shape of the field. This report concerns a study of the Paola shoestring, Miami and Franklin Counties, Kane., where well density of 0.85 acre per well was not uncommon to insure profitable primary recovery in a reasonable time. However, such a great number of wells increased the operator's investment and reduced his profit considerably. It was the purpose of this study to investigate various well patterns and spacings applicable to water-flooding a shoestring reservoir and the effect of these factors upon recovery of oil and the most profitable operation of the pool. The designer of well patterns for a shoestring sand should evaluate carefully the edges of the shoestring, even though they may be considered too thin to drill. These comparatively thin edges contain large quantities of recoverable oil; moreover they are resaturated with oil as the pool is water-flooded.

Jan 1, 1951