Search Documents

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By D. R. Dollnar

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2002

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By Wm. F. Netzeband

"The mode of ore occurrence and the methods and costs of mining at one of the zinc-lead mines in the Tri-State zinc and lead district, Oklahoma, are presented in this paper for the information of mine operators in other districts.No. 2 mine property was acquired by lease in 1918 after some 30 holes had been drilled and a shaft had been sunk to the 305-foot level by the first lessees. After acquisition of the lease, the present operating company drilled a rich ore body on the 260-foot level and in 1920 started sinking two shafts. Production was begun late in 1921, and the mine has been operated more or less continuously to the present time.The mill has a capacity of 400 tons in 10 hours, the usual length of the mill shift in the district.The geology of Mine No. 2 is very similar to that of Mine No. 13 except that the Cherokee shale is thicker, ranging from 80 to 160 feet, and all the formations are correspondingly deeper, the Short Creek oolite horizon here being at a depth of about 300 feet. The oolite has not been found on this property, but the lime comes in at about the level at which the oolite should appear.The ore deposits of Mine No. 2 occur in the brecciated and bowlder ground above the Short Creek oolite. The main or 260-foot level is about 40 feet above the oolite horizon, and the lower or 300-foot level is immediately above it.The ore deposition is controlled by a zone of shearing and fracturing, and the mineable areas are divided into two distinct runs which have a northwest trend with a lean or practically barren area dividing them. This characteristic has controlled the mining to a large extent, for it enables the mine superintendent to locate the large pillars in lean ore and leave only small pillars in the richer ore. Figure 1 shows the outlines of the ore body and the pillars.The ore on the main level occurs disseminated throughout the jasperoid breccia as patches or lenses in the jasperoid, or cementing massive bowlders of jasperoid breccia and chert. The ore of the lower level is more of the bowlder type than that on the main level and occurs chiefly cementing the bowlders but also with some disseminated ore in the jasperoid breccia.The gangue minerals are jasperoid breccia, chert, and dolomite. Calcite is found in minor quantities. Sphalerite is the principal ore mineral; galena is found only in minor quantities around the edges of the ore body. When galena is encountered in this ore body, the limit of the ore can be expected.The exploration and estimation of ore reserves at Mine No. 2 are similar in many respects to the methods used at Mine No. 1.4After the mine was opened up and the general character of the ore deposit had been determined, drilling operations were concentrated along the trend of the shear zone. Later drilling has proved what appears to be a parallel shear zone or an offset of the zone now being mined."

May 1, 1929

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993

By Larry G. Stolarczyk

An underground medium frequency radio communications system has been developed and demonstrated in both coal and metal/non metal mines. The principal advantage of the system are its low cost, ease of installation and the ability to provide radio communications to any vehicle or roving miner in the underground mine. The system provides high quality radio coverage in work areas and along manways with existing "wireplant" conductors. The conductors include AC power cable, telephone cable, metal water and high pressure air pipes, etc. The measured communications range from the base station to mobile transceiver exceeded 12,500 ft without the use of repeaters. A cost/benefit analysis shows that the initial cost of the equipment can be returned 2-6 times in the first year. The mine productivity increases by approx. 13 percent.

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

By James R. Cosby

This report describes work performed for the Bureau of Mines to evaluate available portable instruments for their effectiveness in detecting and locating damaged metallic shields in Types SHD and SHC cables. A second phase of the program is also covered wherein several instruments of a type which show promise are purchased for modification and testing to verify their performance.

Jan 1, 1980

Develop a new technique of in situ rock stress measurement which can be used when and where the conventional methods, such as the overcoring stress relief methods and the hydrofracturing method, cannot be effectively applied. Approach The Bureau of Mines developed basic principles to determine existing biaxial stresses in rock mass by using an instrumentation package consisting of one 3.8-cm-diameter hydraulic cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated flat hydraulic borehole pressure cells (BPC) to he installed in a single drill hole.

Jan 1, 1988

By A. U. Miller

"Ventilation is one of the meet important factors in mining, although until recent years less thought has probably been given to effective ventilation than to any other one phase of mining. In the past, very little, if any, attention was given air courses until they became so constricted by falls that the volume of air was greatly reduced; and, in addition, the stoppings and doors were so poorly constructed that only a very small percentage of air reached the face workings.As a matter of fact, mines have been visited where the volume of air being circulated in certain sections was much larger than in others, and where the management was striving to increase the flow of air in those sections with the least air current, believing the ventilation to be deficient. After sampling and analyzing the return air from the various sections in such mines it has been found that the quality of the air in certain places with the largest flow was more impure than in some of those with the least flow.In past years, practically all mine fans were operated by steam-driven engines supplied with steam from the mire boiler plant. No check was made on the steam consumption or the power cost of operating the fan, therefore the management had very little if any definite information as to cost of ventilating the mine.With the increased use of electrically-driven equipment in mines electricity is being used more and more to drive mine ventilating fans, and since in many instances the current is purchased from central power plants operators have come to realize that in many cases the cost of operating the fans is very high. Some engineers estimate that it ranges from 20 to 50 per cent of the total power cost of the mine. This information, together with the fact that mines are now being developed on a larger scale, requiring larger quantities of air for the men to dilute the gases liberated, has caused the large progressive companies to make, a more comprehensive study of mine ventilation, resulting in a decided improvement in the quality and quantity of air at the face workings, as well as reducing materially the ventilating costs."

Oct 1, 1930

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Ren G. Dong, Kristine M. Krajnak, Dan Welcome

Continual occupational exposure to vibrating hand tools can damage the neural, vascular and other soft tissues of the fingers. Rat tail models have been developed to investigate the biological responses of the tissues to vibration.1-2 However, the biodynamic response of the tail relative to that of the human fingers has not been characterized. The objective of this pilot study was to compare the transmissibilities of rat tails measured via a scanning laser vibrometer to those of human fingers gripping a handle. Methods In Part I of this experiment, four male Sprague Dawley rats (6 weeks old) were exposed to discrete 5g-rms sinusoids of 32, 63, 125, 160, 250, and 500 Hz. The rats were restrained in Broome-style restrainers with their tails constrained without compression to an exposure platform via elastic straps as shown in Figure 1. The platform was attached to a vertically vibrating shaker. The vibration was measured for the array of points shown in Figure 1 using a scanning laser vibrometer (Polytec) and the transmissibility calculated for each point on the tail relative to the reference points on the platform. In Part II, three male human subjects were exposed at the frequencies specified in Part I - with the addition of 1000 Hz - at a magnitude at the ANSI <0.5-hr limit up to 63 Hz, after which the acceleration was held constant at 5g-rms. The subjects gripped an instrumented handle at 20 N as shown in Figure 2. The transmissibility was calculated relative to the reference points on the handle. [ ]

Jan 6, 2006

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By C. H. Riggs, Kenneth H. Johnston

The application of modern secondary-recovery methods has made possible the the extraction of more than 13 million barrels of crude petroleum from the eastern part of the Delaware-Childers field Nowata County, Okla., over and above the production that might have :been expected by continuing primary production methods, including the use of vacuum. Foremost among the secondary-recovery methods used in this foil was the repressuring of the Bartlesville sand with air and gas through injection wells spaced on sym-metrical patterns. Between 1925 and 1945, about 51 billion cubic feet of air and gas were injected into the producing formation, and the total recovery was increased from, 25 million to about 40 million barrels of oil. To produce as much as possible of the 28 million barrels of recoverable oil remaining in the sand will require the initiation of systematic water-flooding projects on many properties and the continuation of air and gas injection on others.

Dec 1, 1946

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By W. C. Blanchard

Time Domain Reflectometry (TDR) is a remote sensing technique using active backscatter. This technique is applicable to the testing for faults and multiple partial faults on cable. The battery operated hardware developed on this con¬tract has tailored this technique for testing of mining equipment trailing electrical cables. The processing of-t-he back-scatter is accomplished using a microprocessor. The visual output from the hardware to the operator is; the type, magnitude and distance to the cable fault in a numerical format. This greatly simplifys the use of this techniques for the operator.

Jan 1, 1980

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930