Search Documents

By John R. Schuring, Walter Konon

The 2.0 in./sec. peak particle velocity criterion traditionally used to protect structures from blast induced vibration damage is non-conservative for landmark structures. Various factors which must be considered in establishing vibration criteria for landmark structures are discussed. Existing criteria by past investigators for this class of structure are presented.

Jan 1, 1984

The most common method for identifying the potential for blast damage is the peak particle velocity. But this can depend on many factors such as the type of blast, explosive, confinement, timing and the rock mass. The value must then be used to estimate damage. But the amount of damage will depend on the rock mass quality and the excavation size and shape. The amount of damage that can be accepted will depend on the purpose of the excavation. This paper presents a logical, but very approximate, procedure that the mining engineer can follow in order to assess the potential for damage in the control of that blasting.

Jan 1, 1987

By Mike Cammack

Western South Dakota is predominately an agricultural area, with exception of the mining and timber industries in the Black Hills region. With precipitation rates averaging below fifteen inches per year, water is a precious commodity to the livestock industry. There is a constant demand for the construction of earthen water storage facilities (dugouts) to catch snow and rain runoff, or developing natural springs.

Jan 1, 1993

By J P. Tidman

The problem of blasting fragmentation has received a good deal of attention in recent years. Progress by the scientific method requires a good set of experimental data as a benchmark to test models. Recent models have become so complex that it is not possible to use the results of field data because the complete set of parameters needed to describe the rock and/or explosive are not available.

Jan 1, 1991

By A B. Andrews

The use of sequential blasting techniques that combine surface and in-thehole delays has provided blasters with increased flexibility in blast design to promote good rock fragmentation and displacement while minimizing offsite blast effects such as air blast, flyrock, and ground vibration.

Jan 1, 1981

By Lee Julian

Ground vibrations generated by mine blasting must be controlled to comply with legislation and to protect sensitive local or site infrastructure. The consequences of exceeding imposed limits can range from negative publicity to structural damage to infrastructure. It is imperative that vibrations are controlled without compromising fragmentation and delivery of blasted inventory. General practice is to reduce the charge weight and the blast size as blasting approaches the sensitive structures; however such an approach results in blasting smaller volumes more frequently which places greater pressure on production to meet their targets.

Jan 1, 2014

By Trevor Ames

Highwall instability, and sometimes referred to as ground failures, historically are a consistent contributor of mine injuries and fatalities within surface mines. To combat this several efforts, including those from NIOSH (CDC), to educate the mining community with insightful literature focused on hazard recognition and advances in ground monitoring systems have been performed. The question is can more be done or is this our last line of defense to manage potential dangers? Is there a more effective method to reduce hazards presented by ground failures including rockfalls?

Jan 1, 2015

By Larry D. Lawrence, Gerald W. Greenway

Corrugated boxes have been the dominant shipping container for packaged commercial explosives for the past 3 decades. Recent changes in shipping regulations have dictated to the industry the adoption of enhanced standards dealing with the construction of fiberboard shipping containers for explosives. Effective October 1944, all shipping containers used for explosives will require individual certification verifying that the containers conform to the United Nations performance oriented packaging standards. The U.S. Department of Transportation will continue to enforce compliance to the new UN standards. A renewed emphasis on the design of corrugated shipping containers to insure industry compliance to the UN standards has been a joint development program between the explosive manufacturers, fiberboard container suppliers and the academic community. Along with drop strength, leakproofness, and vibration resistance, the individual stacking strength of corrugated shipping containers has come under tight scrutiny based on the new UN standards.

Jan 1, 1994

By David E. Siskind

U.S. Bureau of Mines Report of Investigation 8507 was published in 1980. In a comprehensive analysis of all known blast damage studies plus new definitive data, the USBM authors adopted new safe level criteria of 0.5 & 0.75 in/sec for the frequency range corresponding to structure resonances. These were 3 to 4 times lower than the existing limit of 2 in/sec and are the most restrictive scientifically-based blasting criteria for the prevention of threshold hairline cracks in homes. The Bureau's own tests involved 76 homes in six states. In USBM RI 8507, those tests were combined with data from nine other studies from the US, Canada, Czechoslovakia and Sweden in an overall conservative summary analysis intended to preclude blasting damage.

Jan 1, 1998

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By Rafael Tadeu Pinto e Moura, Giorgio De Tomi, Jacopo Seccatore

This paper describes a research and development project in an open-cast mine with the goal to achieve an average P80 of 300 mm (11,8”) in the run-of-mine (ROM) product without altering the existing budget. The project included several variables in the blast design that were not previously taken into account, such as the orientation of natural joint sets in the rock mass, specific energy of the explosive and firing sequence. The new blast design method considered the directions of natural joint sets and determined the drilling pattern and the firing sequence accordingly to favor the movement of the blasted rock along its preferential direction, to reduce its confinement. At the end of the project, it was achieved an average P80 of 304 mm (12”) in the ROM, 50% lower than the one at the beginning of the project. The final blast of the project showed a reduction of 3% of the drill and blast cost, employing the same powder factor and the same drill pattern size used at the beginning of the project. The results achieved show how rock fragmentation is related to variables that are not contemplated in the most common fragmentation models: the firing sequence and the direction of movement in the blast.

Jan 1, 2015

By David Jones, Jeff Bregar, Damien Bell

We have analyzed overpressure and ground vibration measurements for construction blasting for a large pipeline project. These field-measured levels have been compared to existing prediction curves in the literature and new curves have been proposed for overpressure and ground vibration for pipeline construction blasting activities.

Feb 1, 2020

By J T. Patterson

The mining, quarrying and construction industries are often blamed for causing damage to residential-type structures when explosives are used. The claim experience for blasting vibration damage has been poor. This coverage is excluded from the Comprehensive General Liability (CGL) policy. To obtain this coverage, the policyholder must meet additional criteria and an additional premium must be paid. The risk management process offers the explosives user a technique for minimizing the risk of complaints and vibration damage claims on his insurance program and his cash flow. Case histories indicate that the vibration damage claims expense may be a lower risk than the risk of interference with production and cash flow. An annotated bibliography on risk management and defense of vibration damage claims is provided.

Jan 1, 1978

By Stanley L. Lippincott

A number of Federal and State agencies require formal training for blasters. Federal agencies often specify the need for initial training involving all job responsibilities as well as periodic refresher training to assure adherence to current operating procedures. failure to provide and document such training can result in substantial penalties.

Jan 1, 1995

By J L. Jethwa, A G. Gaithankar

The paper deals with a software method developed to design the optimum blast parameters for tunnels and mine roadways for a given set of geo-mining condition without any major discontinuity. The application of the software is presently limited to 8 D-ahaped excavation where inclined hole cut or four-section parallel cut is used with smooth blasting technique.

Jan 1, 1993

By Bob de Raadt

The main problem in blasting a fly-over spanning a main road is the brief time available for blasting and the removal of the debris, in order to minimize the ensuing traffic disruption in the public highway below. The blasting plan is consequently based on an extreme "time is money" concept, in which speed and public safety are predominant factors. This paper discusses reliable blasting parameters for this type of demolition.

Jan 1, 1984

By Michael Wieland

Three laboratory tests were developed for rating the wave-impact ruggedness of cap-sensitive explosives that are used for blasting in underground coal mines. Destructible pipe fixtures, called simulators, reproduce the shock wave or rift compression registered during the cross-hole wave interactions. The rift-compression fixture was modified to render quasi-static desensitization, when utilized with a remote air supply. Waves that were recorded near charge explosions show narrow pulses resembling underwater shock waves, followed by wide, weak humps, called rift compressions.

Jan 1, 1996

By Hike Humphreys, Geoff Baldwin

A project aimed at blast optimisation for large open pit coal mines is utilising blast monitoring and analysis techniques, advanced dragline monitoring equipment, and blast simulation software, to assess the major controlling factors affecting both blast performance and subsequent dragline productivity. This has involved collaborative work between the explosives supplier, mine operator, monitoring equipment manufacturer, and a mining research organisation.

Jan 1, 1994

By Jhon J. Silva Castro

Blast vibration records used in mining contain unwanted information in the form of noise due to long-period drifts, background noise, and noise due to the conversion of the analogue signal to a digital signal. When recorded signals from blasting are used to find other physical variables, such as going from particle velocity to acceleration or displacement, the additional information in the vibration signal can result in inaccuracies in the estimation of the peak values and more dramatically, the results in displacement or acceleration can be nonzero near the end of the record. There are different proposed methods to clean or filter the unwanted information from the signal. All of the methods are based on finding the best fit of the record average value (baseline) and then subtracting from the record under analysis to produce the desirable adjustment. Different criteria and functions are used to define the best fit. The function to use will depend on the shape of the record average values. The main characteristic of the baseline function is that it represents a low frequency wave. Such a low frequency wave can be a periodic function or a polynomial expression of nth order. According to the order of the polynomial expression, the baseline correction can be linear, parabolic or high order. In this document the detailed procedure and the results for the baseline correction of a blast vibration record using a periodic function and a polynomial expression of different order is presented. The results show that the drift problem when displacement is calculate using velocity records increases with the increase of the distance from the blast.

Jan 1, 2015

By A. W. (Sandy) Neilson

Whether you are a general contractor who hires subcontractors to perform blasting work or you have your own blasting crew, it is extremely important to understand how Business Liability Insurance works, regardless of who is ultimately providing the coverage. If close attention is not paid to the limitations and preblast survey requirements under most policies that provide blasting coverage, you could find yourself facing an uninsured loss.

Jan 1, 2002