Search Documents

By Roger E. Scholl

Data on off-site low-rise building damage from underground nuclear testing at the Nevada Test Site (NTS) of the United States Atomic Energy Commission (AEC) [The AEC has been called the United States Energy Research ant Development Administration (ERDA) since 1975, but because the data presented here were gathered between 1966 and 1970, the AEC rather than ERDA is referred to in this paper.] are available for seven large tests in the period from 1966 to 1970. The data, while sparse, provide an adequate sample for the investigation of motion-damage relationships. Damage in the study is statistically described in terms of the incidence of damage complaints, the incidence of buildings damaged, and damage cost. Using 5%damped response spectrum acceleration amplitude to characterize ground motion, the plotted data fit reasonably well with previous motion-damage relationships established from extensive data available from the 1969 RULISON underground nuclear explosion (UNE) experiment conducted in western Colorado.

Jan 1, 1976

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By Ruilin Yang

This paper presents a fragmentation model for large production blasts. The model uses peak particle velocity (PPV) induced from the blast as a controlling parameter to predict the fragmentation size distribution. The PPV can be related to shock pressure or strain under a given rock condition. The fragmentation size is calculated at three-dimensional grid points within the blast volume. The grid size defines the calculation resolution of the model. The fragment size distribution is assumed to be in the same form as the crack distribution within a cube (of the size equals to the grid size) surrounding a grid point. The crack distribution in rock from impact is based on the finding from previous researchers (Seaman et al., 1976). The fines and oversized blocks are calculated explicitly. The summation of the size distribution at all calculation grid points over a specified volume of the blast yields an overall size distribution for the volume.

Jan 1, 2015

By Michael Laing

"Geology plays a critical role in many aspects of blasting, from fragmentation to wall control. One often overlooked component of blasting concerns blast results due to the effect of geologic features. The direction of blasting, with respect to strike and dip, can produce varied results, depending on thescenario. Working with geological features, as opposed to against them or without regard to them, can therefore dramatically improve blasting results. This paper focuses on the role of “geologic features”, which include joint-sets, natural fractures, and bedding planes (all of which are commonly referred to as “seams”) for the purposes of this paper. The goal of this paper is to promote understanding and mitigation techniques for various scenarios in which there are identifiable geologic features. Depending on the nature of these features (strike and dip specifically), blast design and pit advancement/development can be carefully considered to use make the best use of these features and optimize blast results."

Jan 1, 2016

A case history is presented where a variance was permitted by the court to change a 500 foot limit to 250 feet for blasting overburden at a surface coal mine in the proximity of a historic structure.

Jan 1, 1991

By N K. Jain, Rajesh Jain

This article has been written indicating the present trend in Blasting all over the World, so as to help in planning production and development of Industrial Explosives for the development of industries in all the countries in general

Jan 1, 1992

By Wiliam Reisz

As we approach the peak season for thunderstorm activity it’s important to keep in mind that lightning still poses a serious threat to drilling and blasting operations. Lightning remains the number one cause of accidental detonation of explosives.

Jan 1, 2008

By Larry R. Fletcher

Excessive flyrock, which is blasted rock that travels beyond the secured blast area, is responsible for 25 pct of the blasting injuries that occur in surface mining. Excessive flyrock is also a frequent cause of damage to mine equipment and facilities.

Jan 1, 1986

By Jay P. Tobin

This paper will address the legal standards applicable to construction blasting lawsuits and offer best practices suggestions for pre-blast inspections, documenting the construction blasting work, recordkeeping, and effectively participating and partnering in the defense of a construction blasting lawsuit.

Jan 1, 2015

Many North American coal strip operations are practicing trajectory control blasting with good results, often based on trial and error methods. This study summarizes the basic technical requirements for the design of bench-type casting with explosives to achieve further improvements.

Jan 1, 1987

By Robert Hopler

Complying with our request in the February issue of the AGRICULTURAL BLASTER for items that would be of interest to other blasters, Mr. Thomas H. Benton of Tennessee sends us an article in which his methods of securing contracts are explained:

Jan 1, 2013

By R Heater, G Glynn

Various small diameter commercial grades of slurry and emulsion explosives were tested and compared. Velocity diameter curves for confined and unconfined charges were established and the effects of temperature and hydrostatic pressure on critical diameters and minimum primer weights were determined.

Jan 1, 1984

By B. K. Rath

The Industrialization of a country depends on its mining activities to a great extent. In mineral production, India has a top rank not only in South Asia, at the global level too. Quantum of mineral production is almost directly proportional to the quantum of explosive production. Mining sector consume more than 80% of country’s explosive production. Due to rapid growth of mining activities in the country, the explosives industry has been developing very fast in terms of quantity, quality and types. , In this paper, India’s post independent chronological date regarding use of explosives, their types, their constraints and a profile of well-known manufacturers has been meticulously presented. A production figure for three years with system analysis has been presented. The paper also deals with present consumption pattern while making a futuristic forecast. In view of the anticipated changes that are to take place in mining industries in near future, the manufacturers of explosives have to pay a vital role. The paper highlights some concrete and valuable suggestions and recommendations. Small scale Companies have to limit their production to Slurry and Emulsion types of Cartridged explosives whereas the large manufacturing units have to concentrate on Bulk explosives, specialized explosives and better initiating systems. The large manufacturing units have also to make all concerted efforts to compete with global market for significant export. The Country for its rapid growth needs basic raw materials like Coal, Iron Ore and Limestone. So, the extraction of these minerals is of prime importance. The more we produce and consume, the more will be Industrialization. The Industrial growth rate has been around 6% during the last few years. As the Industrial growth rate is moderate, there is moderate increase in mineral extraction in the Country. Additional mineral extraction demands additional explosive production (Annexure-1).

Jan 1, 2000

By Miie Shields, Ed Billington

Trail blasters for the National Park Service (NPS) live and work in remote mountain terrain throughout the western states, where any support or resupply may be sporadic and ditlicult and mountain weather affects every activity. Mechanical “aids” are the pick, shovel, rock-bar, wheelbarrow, and a Pionjar or Cobra dritl. The blaster is usually faced with an extraordinary range of work, t?om delay blasts in weathered rock using driiole depths of 18” (46cm) to as little as 4” (1 Ocm), through reducing boulders and talus fields to useable tread, blasting stumps, snags and log-jams, to the explosive disintegration and casting of animal czcasses. One day he/she might provide a 500cf (14 cu meter) anchor excavation for a suspension bridge, the next day directionally fall 60” (1.5m) diameter snags in a camp area, and the following day blast a 3-foot-wide (1 meter) tread bench across a steep bedrock slope. To be effective, the blaster must design each and every blast around desired end result, crew and public safety, maximizing effective use of limited quantities of explosive, and the minimnation of environmental effects. Since almost all drillhole blasting occurs in the weathered zone of the rock, blasting is more the art than the science of judging rock density, hardness, cohesion and prefracturing, and selecting explosives, drill and delay patterns, and loading techniques responsive to those conditions. For these reasons the NPS issues its own Blaster’s License, with a basic requirement of at least 40 hours of NPS blaster training and 3 years of supervised Blaster in-Training experience. The focus of this pre-license requirement is on safety and using explosives as a precision tool, versus just “blowing things up”.

Jan 1, 2002

By AJ Rorke

Blasting trials using Daveytronic Electronic Delay Detonator systems (EDD’s) were conducted at the Alpha Ferro Quany (Pretoria) and the Eikeboom Colliery near Witbank in November 1999. The objectives of the trials were to determine the influence of accurate hole firing on rock fragmentation, blast-induced vibration and blast throw. This paper provides an outline of the trials and an analysis of the results. The results were compared with a normal shock tube initiation system. Fragmentation was measured using video-imaging techniques at the hard rock Ferro Quarry for one conventional shock tube blast and two EDD blasts. No significant difference was measured in the fragmentation between the shock tube blast and the two electronic detonator blasts. Joint planes mostly defme the fragments at Ferro Quarry. The fragment sizing was therefore controlled mainly by the rock structure and the blast timing appeared to have no influence. Vibration measurements made at Ferro Quarry indicate that electronic detonators have a marked effect on vibration frequencies compared to shock tube systems. The more accurate detonators resulted in a narrower f+equency band at lower amplitude with similar timing. By modifying the blast timing, the dominant frequencies were changed. The electronic detonators had a significant positive influence, therefore on blast vibration and its control. The timing scatter measured from the shock tube blast was considerable, with measured inhole detonator scatter at 48 ms over a sample of 19 units. Surface delay periods less than 42 ms would therefore not be able to provide effective sequential firing. The scatter of the Daveytronic units was below the 2 ms resolution of the high-speed camera used to film the blasts. Reliable sequential firing, even at very short delay intervals was considered the main reason for notable improved throw in an overburden blast at Eikeboom Colliery. Blast throw was improved by 25% for the test blast.

Jan 1, 2000

By Eduardo Berger

This paper describes a mechanized loading system, the HYDRODOSE, which allows the use of pumpable emulsions in underground mining. It also describes a pumpable emulsion explosive for small diameter holes, HYDROMITE PDB. Included are test results carried out in two Chilean underground mines.

Jan 1, 1991

By Erik K. Lauritzen, Jorgen Schneider, Niels Madsen

From 1986 to 1988 Kalaallit Tunisassiorfiat (KTU)/Gronlands Hjemmestyres Produktionsvirksomhed (the part of Greenland's own governing body which is in charge of production activities) has been responsible for blasting projects in the following 4 towns: Ilulissat/Jakobshavn, Qasigiannguit/ Christianshab, Qeqertarsuaq/Godhavn, Sisimiut/Holsteinsborg

Jan 1, 1989

By Robert L. Brooks

This paper is intended for companies at all levels of the Explosive Industry and in particular, those that do not have a risk manager. It is strictly informational in nature and no reference is made, or intended towards any existing insurance company or agency.

Jan 1, 1993

By R. Wharton, M. Bagley

Following a series of papers relating to the certification of explosives for sale in member states of the European Union presented at previous ISEE conferences, this poster paper has been prepared to stimulate discussion and debate on the recently published European Directive on Pyrotechnic Articles.

Jan 1, 2008

By Robert A. Farnfield

This paper outlines the theory behind transfer functions and illustrates their application in the prediction of structural response to blast induced ground vibration. The ability to predict the response of a structure to a recorded ground vibration is desirable for a number of reasons.

Jan 1, 1994