Search Documents

By Thomas P. Dowling

Since the 1950's, blasting practices have undergone many revolutionary changes. Some of the more radical departures have involved, in addition to high speed drilling equipment, a myriad of new explosives, blasting agents, boosters, initiators, initiating systems and delay devices. The introduction of ANFO in the mid 1950's as a blasting agent seems to have instigated a trend toward the development and use of less sensitive blasting agents. The evolution of slurries or water gels has produced dense, high strength, water resistant products which has further promoted this trend away from the more sensitive, conventional explosives.

Jan 1, 1975

By Eugene Baker

President George Bush signed the Safe Explosives Act (SEA), which amended the Organized Crime Control Act (OCCA) of 1970, into Law on November 24, 2002. As a result of this legislation, new restrictions on who could legally receive or possess explosives in the United States went into effect, resulting in a profound impact on the commercial explosives industry. The law went into effect in two key phases. The first phase, which went into effect on January 24, 2003, resulted in additions to the categories of persons who are prohibited from receiving or possessing explosive materials in the U.S.

Jan 1, 2004

By Braden Lusk, Kyle Perry

Recent events and MSHA actions have resulted in discussion and reevaluation of the practice of sealing abandoned coal mine workings. In the past, MSHA has approved alternative seals based on a pass/fail system that required minimal engineering. Disasters involving fatalities led MSHA to impose higher seal pressure requirements based on research and experiments. Impending new MSHA seal regulations will force manufacturers and industry to obtain a high level of engineering expertise. The expertise necessary is in the field of blast resistant design, which is not easily accessible due to the limited number of experienced individuals within the mining industry.

Jan 1, 2008

By Mark S. Stagg, Rolfe E. Otterness, Stephen A. Rholl

The Bureau of Mines has developed computer software to study the effects of initiator scatter on all aspects of the blasting process. The software is useful because it is difficult to obtain actual initiator data, particularly the standard deviation which is needed to express initiator scatter. The new software is structured to allow blasters to answer the question: how precise must initiators be to insure a successful blast? Successful is defined statistically in terms of a confidence level. The software can be used with any possible design since there are no restrictions due to size or complexity.

Jan 1, 1992

By Mike Wheat, Catherine Aimone-Martin, Brandon Pease

The Kneeling Nun rock pinnacle is a prominent landmark, 90 ft in height and 35 ft in width, that resides on a bluff overlooking the Santa Rita pit at the Chino Mines Co. operations near Silver City, New Mexico. The company plans to expand the current pit limits, resulting in a change in direction and distance of hard rock mine blasting operations in relation to the pinnacle. Concerns about the stability of the pinnacle adjacent to mining activity has prompted company personnel to enhance the seismic monitoring program both on the pinnacle and along the current open pit highwall that forms the base support below the pinnacle foundation. This paper presents the vibration response characteristics of the pinnacle, in terms of amplitude and natural frequencies of motions and damping characteristics, for measurements recorded at the top and base of the pinnacle. The influence that blasthole initiation timing and sequence of hole detonations have on vibration response is discussed. A simple analysis is made to estimate factors of safety against cracking of the landmark as well as blast-induced slope instabilities within the foundation rock.

Jan 1, 2000

By Robert Hopler

The 1800’s were a time of tremendous advancements in science and experimentation, and earthquakes were a subject of great interest. The meetings of the British Association for the Advancement of Science in 1853 and 1854 are good examples of this. The proceedings of the Association for the 1854 meeting includes a table entitled “Catalogue of Recorded Earthquakes from 1784 to 1850” which takes up 326 pages, and lists available information on approximately 3000 earthquakes. The 1853 proceedings have a similar table for earthquakes recorded from 1606 B.C. to 1783. In the 1854 volume there is a “Report of the Committee on Earthquakes,” which provides us with a view of the general state of the science. Excerpts from that report follow:

Jan 1, 2006

By Dennis G. Wright

The Minister of Fisheries and Oceans for Canada is responsible, under the Fisheries Act, for the protection of all marine organisms and their habitats. The detonation of explosives in or adjacent to fish habitat has been demonstrated to cause disturbance, injury and/or death to aquatic organisms, and/or disturbance, destruction or alteration of their habitats. The Department of Fisheries and Oceans recognizes that the use of explosives may be the most practical or cost effective method by which to complete a project and has undertaken the development of a set of guidelines that will prevent or minimize the destruction of or disturbance to aquatic organisms and their habitats while at the same time allowing scientific and industrial users of explosives to proceed with their projects.

Jan 1, 1997

By Gregory Lorsbach, Wade Hutchison, Earnest Grigoryan

Comparing measurements from multiple seismographs, particularly when the instruments are deployed in a “side-by-side” situation, is often problematic. Measurements often differ by as much as a factor of two. These differences are attributed to issues related to calibration, geophone coupling, and differences in geology over very short distances. Unfortunately, these explanations are often purely qualitative, but are accepted as factual. Shake table testing often demonstrates that those seismographs that indicate large differences for a particular vibration event, may correlate within a few percent of each other and the known shake table input. Geophone coupling also does not fully explain the difference in measurements since geophones in side-by-side measurements are deployed identically. Differences in geology do not explain the difference in measurements since it would be unrealistic to expect significant differences in distances less than one meter in a normal monitoring situation. Utilizing a new technological approach to vibration measurement and analyzing numerous side-by-side measurements, it has become clear that a significant portion of the observed differences between seismograph measurements are instrumentation induced. This study examines and describes some of the most significant sources of the seismograph error budget.

Jan 1, 2005

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By Cristian Rodriquez, Fernando Fernandez, Rodrigo Fuentealba, Tom BoBo, Maria Rocha, John Kemeny

This paper describes a case study that was conducted at a new mine in South America. This mine has significant geologic variations that will result in different distributions of hard and soft ore being mined at different periods of time over the mine life. A study was conducted to determine the optimum blast design that will meet the mill throughput requirement of 95,000 tonnes (104,720 tons) per day for the first 10 years of the mine life. As part of this study, field rock mass characterization and laboratory tests were conducted. This includes standard rock mechanics tests as well as rock breakage tests used in mill simulations. The geology of the ore body was broken up into four Geologic Units, and statistical variations in the properties were determined for each unit. Using this data along with the data on the occurrence of the different geologic units over time, simulations were made of the run-of-mine (ROM) fragmentation due to different blast designs, and these results were used in simulating the resulting throughput after crushing and grinding. Four blast designs were considered with powder factors of 0.44, 0.54, 0.64 and 0.94 kg/t. The results of this study show that determining the proper blast design is important in ensuring that the mill throughput requirement will be met over the mine life.

Jan 1, 2015

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By Thomas A. Gelormino, Ulrich La Fosse

"Deep blasting was used to densify foundation soils for a large manufacturing facility inChicopee,Massachusetts. A 360,000 square foot building, whose construction began inthe summer of 1990, is founded on alluvial deposits up to 90 feet in depth. These deposits are comprised of saturated very loose to loose fine to medium grained sands with traces of silt and gravel. During the building foundation design it was found that to withstand earthquake forces without soil liquefaction, it would be necessary to improve portions of the alluvial deposits by densification. The zone in need of densification extended from approximate depths of 20 to 50 feet. Several conventional densification methods, including vibrocompaction and deep dynamic compaction, were evaluated along with deep blasting. Detonation of 1-3/4 inch diameter charges of 65 percent gelatin dynamite (Atlas Power Primer) installed inside 2-inch diameter PVC casings to a depth of up to 40 feet, was used to achieve the desired densification. This method was selected over others due to its lower cost and decreased construction time. Although used in New England once in1940 for a dam and once in 1960 for a transmission line tower to improve foundation soils, there is no precedent found in the literature for densification by blasting to improve liquefiable soils below a proposed building. Details of a test program and the production blasting, including vibration data are presented. Pre-and post-blasting data conclusely shows an increase in the density of the sand deposit after blasting."

Jan 1, 1991

By Marcus Neves, Eventomar Junior, Adilson Castro, Leandro Silveira, Sérgio Augusto

The collapse of the Vale S.A. mining tailings dam in 2019, a tragic event that shook Brazil and the world, had consequences that transcended the immediate pain and devastation. Among them, the suspension of rock blasting activities in several mines in the Quadrilátero Ferrífero region of Minas Gerais, Brazil. This measure, taken as a precaution and with the aim of ensuring the safety of nearby geotechnical structures and the population, had a significant impact on the mining production chain. To overcome these challenges and resume blasting activities in a safe and sustainable manner, the mining industry has been dedicated to developing and improving solutions. One of the promising alternatives is the signature hole technique, used in conjunction with attenuation laws. The complex geology of the Quadrilátero Ferrífero, with lenses of compact ores immersed in friable materials, the presence of discontinuity families, and the emergence of geological faults, requires detailed analyses and specific adaptations of the signature hole technique and constant monitoring of the vibrations to calibrate the attenuation laws to ensure compliance with permissible limits and safety of the operations. To demonstrate the methodology, a case study in Abóboras Mine was described. Additionally, the challenge of achieving the desired level of production while controlling vibration and slope damage has driven the development of new charging and timing techniques. To address this challenge, a comprehensive approach was undertaken. A substantial database containing more than 4,000 registers of blasting-induced vibration events from 520 blasts was meticulously compiled from 2020 to 2023, 6 different attenuation laws were established and continuously calibrated with 99.3% of compliance regarding permissible limits of vibrations. The successful implementation of these actions allowed for the resumption of blasting, increasing production from 10 million metric tons to 43 million metric tons per year assuring sustainable operation.

Jan 21, 2025

By Sam Oaks, David A. Smith

The new Corridor "G" Federal Highway Project in Logan County, West Virginia is the largest mass excavation highway project currently being built in the United States. Seven sections covering 14 miles of four lane highway and two connector roads will require over 30 million cubic yards of excavation. Construction is on a fast track schedule requiring the contractors to complete excavation and pavement placement in a little over 19 months. The two different general contractors have implemented several innovative Blasting and Excavation Programs to complete this project within the tight completion schedule. The paper expands on some of these unique programs that made the project a reality.

Jan 1, 1994

By William A. Travnik

For more than 60 years, ESSO RESOURCES CANADA LIMITED has been producing and refining oil at a small refinery in Norman Wells, Northwest Territories, and supplying diesel fuel and other oil products to northern markets. In 1982,ESSOwas granted governmental approval to expend production from the oil field from 475 cubic metres a day to 4400 cubic metres a day. This $800,000,000projectproceeded ahead of schedule for a start up in 1985.

Jan 1, 1986

By Lon D. Santis

This paper describes a lightning warning system (LWS) in operation at the U.S. Bureau of Mines' (USBM) Pittsburgh Research Center (PRC) from December, 1989 to April, 1991. An electric field mill measured the DC atmospheric electrostatic field. Also, an economical on-line weather data service provided lightning location maps and other weather information. A system such as this can significantly improve the safety of explosive handling. The use of these two methods addresses the detection of thunderclouds building overhead and the prediction and tracking of developed storms. Warning reliability of the system was very good when data from both sources were considered. Experience showed, however, that use of either system alone would not provide adequate reliability in most situations. Some problems occurred with the field mill and there is some question whether the instrument is compatible with harsh mining environments or could be made portable. Another method ' of measuring electric field based on fiber optics is discussed. This technology may be able to overcome the problems with field mills.

Jan 1, 1993

By Dale S. Preece, Vanessa S. Berg

Shaped charges are being utilized in defense applications against a wider variety of targets including concrete, rock, and soil. This work was motivated by a heightened interest in characterizing the effect of shaped charge attack on brittle, non-homogenous materials, in particular, concrete damage and penetration predictions resulting from a TOW-2a conical shaped charge (CSC). This paper presents a multi-stage approach for accurately predicting the high explosive detonation and subsequent jet formation due to the collapse of shaped charge liner, the changes in jet length and diameter as a function of standoff distance, and the jet-target impact dynamics. The first part of the analysis approach employs the commercial 3-D Eulerian-Lagrangian hydro-code AUTODYN to predict the shaped charge jet formation. 2-D finite difference Eulerian subgrids represent the explosive and casings components, while thin components like the liner are modeled with Shell subgrids. The Pugh, Eichelberger & Rostoker (PER) jetting theory option is invoked to obtain the jet and slug masses and associated velocities. The jetting data is post processed where the jet velocity gradient and jet mass is used to solve for the new jet length and diameter gradient at a desired standoff. The final computation involves a 2-D fully Lagrangian model in which the jet and velocity gradient is represented by a string of Lagrangian segments and the concrete target is defined as Lagrangian with the newly developed RHT (Riedel, Hiermaier, Thoma) constitutive model. This model has a third invariant dependency that accounts for failure mechanisms in brittle materials.

Jan 1, 2004

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Kirk Yeager

All explosive formulations display some sensitivity to heat. A common technique utilized to measure an explosive’s response to thermal stimulation is differential scanning calorimetry (DSC). As DSC analysis is run on quantities of material easily handled in a laboratory setting, and is relatively inexpensive, it tends to be one of the more predominant tools utilized to determine potential thermal hazards of energetic materials. The analysis of energetic materials via DSC provides unique challenges, as both large energy outputs and significant production of gaseous products result from their decompositions. In addition, the unique thermal decomposition characteristics of ammonium nitrate (AN) based materials have also created difficulties in DSC analyses. A wide variety of techniques have been developed to study the decomposition of explosives. Traditionally, sealed glass capillaries were utilized to house samples. Recently, the introduction of specialty cells designed to withstand high pressures has enabled new sampling techniques to be developed. Analyses of explosives with both traditional and “high-pressure” cells will be compared and contrasted. Lessons learned about the application of both techniques towards analyzing thermal hazards such as incompatibilities will be presented. Inconsistencies in the results displayed during analyses of AN-based explosives will be highlighted. Recommendations on the best approach for analyzing the more problematic AN formulations will be given.

Jan 1, 2000

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980