Search Documents

By Mowat D. M., Louis H., Smith W. Mackey W. M., Dron R. W., Ellison C. C., Winmill T. F., Kerr G. L., Haldane J. S., Ashworth J., Garforth W., O'Shea L. T.

Discussion of Winmill's paper, including various anecdotal examples, is presented together with the author's response; topics included: the need to distinguish cubic pyrites from the rapidly decomposing rhombic form known as marcasite; the effects of moisture content in the coal and air; the possible effect of pressure; the heat insulation resulting from heap/stack size; and the means of determining pyrite and moisture contents

Dec 1, 1916

By S. Y. Ezz

Report of discussion at February, 1971, IMM general meeting (Chairman : M. J. Cahalan, President) of a paper published in Transactions/ Section C (Mineral Processing & Extractive Metallurgy), vol. 79, September, 1970, pp. C226-C233 with contributions by Wild R. and Astier J. on fluidised bed reduction of iron ore fines

Dec 1, 1971

By D. J. Wall, T. D. Johnson, M. T. Parry, G. R. Heath

In coal-fired power stations coal is ground to a fine powder and then transported pneumatically at 25-30 m/s velocity to remote burners. Wear of the conveying pipework is a well recognised problem and traditional lining materials are Nihard and basalt. In many cases these are being replaced by alumina tiles in order to improve life and reduce the frequency of replacement. A programme of laboratory testing of candidate aluminas with AIO, contents between 85% and 99-5% has been undertaken and the results compared with field experience. This gives confidence in the erosion tests, which were designed to replicate most of the field conditions. However, it has not proved possible to draw correlations between the laboratory erosion rates and any of the materials’ bulk properties. SEM, TEM and microanalysis studies have therefore been made in order to look for microstructural aspects that could be influencing erosion rates and it has been shown that intercrystalline cohesion, the matrix phase and porosity appear to have most influence on wear performance. It is necessary to quantify these microstructural parameters if reliable erosion performance is to be obtained. This paper was read at the Institute of Ceramics Annual Convention at the University of Durham, April 1988.

Jun 12, 1905

By P. K. Kaiser, R. K. Brummer

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994. A risk-based decision-making procedure has been developed for selecting rockburst-resistant tunnel support in burst-prone mines. The method is based on a risk-cost-benefit analysis and uses support cost data, costs associated with the risk of support failure or excavation loss, costs associated with accidents, injuries and deaths, and the benefits achieved by installing rockburst-resistant support. It takes into account the risk of damage to the support systems due to rockbursts, potential loss of production and the need to rehabilitate in the event of a damaging rockburst. A practical example is provided to illustrate the principles involved in the decision process

Jun 17, 1905

By B. H. Smith

"Most of the discoveries of nickel sulphide deposits in Western Australia have followed the search for gossans. The chances of further discoveries depend on improving our understanding of the cover of strongly leached and transported materials that obscure approximately 85% of the area of the Yilgarn Block that has nickel sulphide mineralization potential. The lateritic profiles that are observed on the Yilgarn Block today were formed over a period of more than 100 m.y. of warm and humid climates. This lateritized land surface has been preserved by induration during subsequent arid climates as well as by the structural stability of the Yilgarn Block.In geochemical surveys of lateritied terrain samples have to be taken from at least the saprolite zone usually by drilling so that confident predictions can be made of the significance of analytical data. Account must be taken of the mineralogy of samples, as well as the nature of the horizon of a laterite profile that is being sampled, owing to the concentrating effects on trace elements of Fe and Mn oxides.Multivariate techniques have been applied successfully to analytical data in gossan recognition when textural evidence is ambiguous. Pathfinder geochemistry has also been used in gossan recognition and the most significant recent advance has come from studies of platinum group metals in nickel sulphides and their dispersion during weathering."

Jan 1, 1984

By G. B. Hooper, G. A. Ferguson

The technical capabilities and user-friendliness of the major computer-aided mining design software systems are reviewed. Recent experiences with three systems are outlined to indicate the practical problems that arise. The examples were: Microlynx software from Lynx Geosystems at the Great Dyke platinum mine in Zimbabwe; Lynx software from Lynx Geosystems at a copper mine in central Africa; and PC-MINE software from Gemcom Services at an open-pit gold project in Western Australia. Difficulties in the use of mining design software has led to an alternative approach. Falconbridge, Canada, has developed an integrated mine-planning system on a CAD platform that encompasses ore reserve estimation, stope design, development layout and survey control. Future directions of computer-aided mining design using this basis are discussed. A major advantage of using mainstream software packages, such as spreadsheets, databases and CAD programs, is that most engineers and geologists are experienced in handling such systems in the normal course of their work.

Jan 12, 1992

By International geochemical

During the production of the Geochemical Atlas of Finland till samples were collected throughout Finland at a density of one sample per 300 km2. The material studied was the fine fraction of till (less than 0.06 mm). The geochemical mapping has shown that elements that are locally enriched in bedrock in the form of ore mineralisation are also enriched in a wide area of the surrounding till. These anomalous enrichments of ore elements take the form of rectangular or curvilinear zones that are some tens of kilometres wide and hundreds of kilometres long. The mineralised zones host ore deposits of different genetic types and can be termed "ore provinces". They stand out prominently on the geochemical maps and can be divided into sub-units of different chemical composition.

Jan 12, 1992

By D. L. Buchanan, ed. sci.

The issue comprises 10 contributions on PGE mineralisation, of which 9 were presented at the symposium organised by the IAGOD Commission on Ore Deposits in Mafic and Ultramafic Rocks and the BRGM-CNRS University of Orleans research group. The editor's introduction and summary of the papers is presented together with the title page, contents list and cover photograph of a harzburgite ridge, dunite boundary and chromite quarry in the Shetland ophiolite on Unst

Apr 1, 1994

By Fearnside W. G.

Further discussion at the Midland Institute of Mining, Civil, and Mechanical Engineers' general meeting held in Leeds, March 21st, 1916, with T. Beach, vice-president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p. 573 and discussion vol. L., p. 109 and 608, comprised a brief written contribution by Faulds A.

Dec 1, 1916

By S. V. Shiraishi, H. B. Bell

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J. Cahalan, President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C120-C127, with a contribution by Wright P.A. on the miscibility gap

Dec 1, 1971

By W. Doherty, P. C. Lightfoot, V. A. Fedorenko, N. S. Gorbachev, V. I. Kunilov, A. J. Naldrett, Z. Johan

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. A model is presented which regards the Lower Talnakh- and Talnakh-type intrusions as part of the plumbing system for the overlying lavas. As magma ascended along the Noril'sk-Kharayelakh fault it was forced to spread out within sedimentary strata immediately beneath the obstruction of the accumulated volcanic sequence. Here it was severely depleted in chalcophile elements by sulphides, which were then trapped by their high density and remained behind in the main arteries to form the central, elongated zone of maximum thickness. Subsequent magma also lost Ni, Cu and PGE to the sulphides as it flowed through. The Lower Talnakh-type intrusions represent part of the plumbing system that became blocked at an early stage, before the influx of much mokulaevsky-type magma rich in chalcophile elements. The model accounts for the high metal content of the ores in comparison with the size of their associated intrusions, the extensive metamorphic aureoles, the chalcophile depletion of some overlying volcanic suites, the presence of the ore in near-surface intrusions rather than deep magma chambers, and the sulphur isotopic composition of the ore

Apr 1, 1995

Discussion of the paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair, included questions asked and points for discussion raised by Bramall V., Paton J.D., Fletcher L.R., Siddall F.N., Stoker A. and Stone T., in particular on how to eliminate dust

Dec 1, 1916

By C. P. Summerhayes, J. W. G. Gilbey, S. Henley, G. P. Glasby, J. J. T. Harvey, J. Larsson, O. Akiman, A. G. Brown

Abstracts are presented from six University of London, one University of Nottingham and one University of Durham PhD theses

Dec 1, 1971

By P. Seppanen

Cemented fill was first introduced at the Keretti mine in 1952, but entailed high cement costs, the need for stope preparation, slimes handling, clean-up and maintenance, increased mine dewatering, segregation of fill and long setting times. In the 1970s research began into the use of iron blast-furnace slag as a binding agent and by 1989 Pyhasalmi, Vihanti, Keretti, Vammala and Enonkoski had saved US $11 000 000 by using slag binders instead of cement. Viscaria in Sweden and Tara in Ireland also use slag as 90-100% of total binder, although their backfilling methods vary. The main area of interest in slag research is determining the activation methods for initiating the binding reactions; it is also important to achieve other characteristics such as resistance to corrosion by sulphuric ion. New backfilling techniques developed during the 1980s included the use of high-density cemented tailings fill at Vammala and porous cemented rockfill at Enonkoski and Viscaria. Future developments focus on concepts such as integration of mining and milling with backfilling and the achievement of total underground disposal of wastes

Dec 1, 1995

By Briggs H.

Initial discussion of the paper presented at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, included comments by Masterton J. (HM Inspector of Mines) and Sim J., and the author's reply

Dec 1, 1916

By A. L. W. Lips, T. J. R. Barclay, E. Rothery, S. H. White

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994 (originally entitled: The Broken Hill base metal deposit - a tectonically transported and modified basinal deposit within the Proterozoic Willyama fold and thrust belt). A regional structural study was undertaken which incorporated the role of shears. Their positions were identified from earlier mapping, from regional aeromagnetic data and by additional field work. Kinematic studies determined movement histories and petrological studies of the fault rocks formed within the shears identified the relationship between the movements and regional metamorphism. It was found that the shears formed a part of an earlier, major thrust event with transport from NW to SE and a later, minor one in the reverse direction. Neither had any significant effect on the mineralisation apart from local displacement, but the shuffling of the basin stratigraphy adds to the difficulty of recognising the original volcanic and sedimentary protoliths of the metamorphosed sequence. The mineralisation at Broken Hill mine is confined to a single recognisable thrust slice within a shear corridor. It is stratabound with locally transgressive remobilisation due to the high-temperature thrusting and some metasomatic alteration as a result of the retrograde shearing. This variation accounts for the different genetic models applied to the deposits in the past

Jun 17, 1905

By Ruddle R. W.

Although copper has been smelted for many years, relatively small attempt has been made in the past to examine the fundamental physical chemistry of the processes involved. Therefore, technological developments apart, slow progress has been made with the development of improved or new principles of smelting. The methods at present in use in the majority of the world’s smelters are essentially those employed at the beginning of the present century; it is significant that many of the textbooks on copper smelting, written some 50 years ago, are still regarded as standard works. The book is divided into seven chapters. In the first the fundamentals of modern smelting processes are briefly outlined for easy understanding of the subsequent sections, while the next two chapters are confined to the more theoretical aspects of the constitution of mattes and slags. Some problems of considerable practical importance are discussed in the remaining four chapters; these are (1) magnetite formation, (2) copper losses during smelting, (3) the recovery of sulphur from the smokes produced during smelting, and (4) the elimination of impurities. A collection of thermodynamic data relevant to copper pyrometallurgy is presented in an appendix, and, for the convenience of readers not well acquainted with thermodynamics, a brief explanation of the thermodynamic terms and methods employed is given in a second appendix

Jan 1, 1953

By J. J. Mackay

The Parliamentary Under-Secretary of State at the UK's Department of Transport introduced the symposium, approved its emphasis on environmental planning and the mitigation of environmental impact, discussed the publicity resulting from the recent opening of the Channel Tunnel as well as the role of private financing, and pointed out the leading role played by the Department of Transport in the introduction of the New Austrian Tunnelling Method to projects such as the Jubilee Line extension and the Heathrow Express (an editor's footnote, however, mentions with regret the Heathrow subsidence that occurred just before the journal went to print)

Jun 16, 1905

Further discussion at the Mniing Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916, of the paper published in Trans. I.Min.E. vol li, 1916, p.169-186 with discussion p.187-188, included oral and written contributions by McLaren R. and Waddell H.

Dec 1, 1916

By G. Richards

Application of the Internet of Things (IoT) technologies - the interconnection of uniquely identifiable embedded computing devices within the existing internet infrastructure - to the mining industry is discussed. IoT technologies are aimed at making projects safer, better optimised and more economic and are applicable to current or new underground or open-pit mines, regardless of size. Two examples are presented of successful implementation of IoT technologies, the Chelopech gold, copper and silver mine in Bulgaria, where production has increased from 500 000 to 2 000 000 tonnes/y and communication costs have been reduced by US $2 500 000 over 2 y, and the Pilbara project in Western Australia, where remotely controlled wirelessly connected autonomous trucks have covered ca. 3 000 000 miles and hauled almost 250 000 000 t of ore since 2008

Apr 1, 2015