Search Documents

By S. Banisi, Seyyed Omid Mousavi, Alireza Ghasemi

Discrete Element Method (DEM) is extensively used to simulate the behaviour of particles in various processing units. This method is based on modelling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations needed have made the required computation time very long even using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be in error due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The simulation error was defined as the relative difference between the initial restitution coefficient and the restitution coefficient obtained after simulation. The required time steps to arrive at the simulation error of 5% were calculated for two common contact force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, elasticity modulus of 210 GPa, Poisson's ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and the linear spring-dashpot contact force models, respectively. Results showed that with a scaling-down the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and the linear spring-dashpot contact force models, with an equal simulation error, increased by 100 and 316 times, respectively.

Jan 1, 2014

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By X. L. Song

In this paper, ZrSiO4-Cd(S1-xSex) inclusion pigments were synthesized by hydrothermal method. Microstructure, morphology and properties of the powder were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR) and CIE chromaticity, respectively. It shows that, precursors obtained at pH is about 6.0 are sol and products with higher crystallinity, red hues (a*=38.23) and inclusion ratio when hydrothermal synthesis temperature is 180? and holding time is 12h. Hydrothermal reaction mechanism was further analyzed as well. In particular, an ideal model of pigment formation was proposed.

Jan 1, 2014

By Michael Young, Rodrigo Araya, Cesar Gomez, Le Huynh, James Finch

The performance of flotation machines is closely related to the gas dispersion characteristics achieved in their operation. It is known that frothers play a major role not only in the size distribution of the generated bubble population, but also on the swarm rise velocity. A program to characterize frother effects on two-phase hydrodynamics (air-water) of Jameson cells was undertaken in a fully instrumented pilot unit installed at McGill University. Gas dispersion parameters (gas velocity, gas holdup and bubble size distributions) of the gas-liquid mixture generated in the downcomer were measured after its release into the separation chamber. The unit was operated under different conditions including gas velocity, liquid jet velocity and frother concentration (MIBC). Bubble size distributions for concentrations above the critical coalescence concentration (CCC) were narrow with Sauter mean diameter between 0.6 to 1.3 mm. The bubble size followed the general trend as encountered in other types of flotation machines, i.e., rapid decrease with increasing frother concentrations below 10 µL/L, and almost no change in size for concentrations above 30 µL/L. The CCC was between 10 and 15 µL/L. Strong correlations were found between bubble size and air-to-liquid flow ratio (APR), and between the bulk density of the aerated solution in the separation tank and the vacuum inside the downcomer. An equation is proposed to estimate gas holdup in the separation tank from vacuum and bulk density readings.

Jan 1, 2014

By Q. R. Chen

Wet processes are commonly used in coal preparation field home and abroad. Dry coal cleaning technology is very necessary in China because more than 2/3 of coal resources deposited in arid areas, which are difficult to separate coal with wet processes. A particular interest of this article is the discussion of separation research development of dry coal cleaning in China, such as an air dense medium fluidized bed (ADMFB) beneficiation technology, a compound dry (pneumatic) separation technology and a triboelectrostatic separation technology. The fundament and importance of dry coal cleaning methods above were introduced. On the basis of analyzing parameters which influence the performance of separators, including that of structure, technologic and operating, the separation research status of dry coal cleaning methods, especially the ADMFB beneficiation technology, were discussed and reviewed. The recent developments, especially the fluidized bed beneficiation for <6mm fine coal with an external energy assisted, including a vibrated fluidized bed and a magnetically fluidized bed, and the triboelectrostatic separation for <1mm fine coal are also introduced. The study and application results in China show that dry coal cleaning technologies can efficiently beneficiate different coals with different sizes. The ADMFB can separate >6mm coarse coal with an E value of 0.05~0.08, the external energy assisted fluidized bed can separate <6mm fine coal with an E value of 0.07~0.09, the triboelectrostatic technology can efficiently separate <1mm fine coal, and the compound dry separation technology can efficiently separate >3mm coal with a easy washability. The dry coal cleaning provides an efficient and lower cost clean approach for coals distributed in arid areas.

Jan 1, 2014

By A. N. Zagorodnyaya, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva, A. S. Sharipova

"In Kazakhstan, there is a unique sulphide copper deposit, in the ores containing the natural isotope of osmium-187 (more than 90 %). In the pyrometallurgical processing of concentrates for the target metal, osmium is mainly sublimated, with wet cleaning of metallurgical gases (dust and gas mixture) 40 % of it together with rhenium passes into washing solutions (wash acid). On the basis of this acid, the production of ammonium perrhenate was organized at the enterprise of the RSE ""Zhezkazganredmet"" and for the first time in the world practice - the isotope of osmium-187. However, the degree of its recovery from solutions does not exceed 8 % of the amount supplied with the charge or 25 % of the amount that was received for extraction. But the bulk of it (~ 75 %) remains in the raffinate, discharged to sewage treatment plants (wastewater). The studies presented in this work are aimed at solving the problem of osmium isotope-187 extracting from wastewater, which are a potential source of increasing metal production in Kazakhstan. The aim of this work is the development and scientific justification of osmium deposition regimes from wastewater using such reagents as thiosulfate and sodium sulphide. The influence of various physicochemical factors on the precipitation of the osmium was studied and optimal conditions for its maximum transition to sediment were chosen. An original method for obtaining osmium concentrate in the presence of sodium thiosulfate with the addition of potassium iodide from a new type of wastewater - man-made ammonia solutions has been developed. These solutions were combined mother liquors of solid-phase stripping operations and dissolution of pulp of crude ammonium perrhenate. On the basis of the obtained results, a settling technology for extraction of the osmium from man-made ammonia rhenium-containing solutions was introduced at RSE ""Zhezkazganredmet"". It should be noted that the degree of extraction of osmium, depending on its concentration in solutions entering on the settlement, and taking into account the addition of sulfuric acid, will vary from 60 to 90 %. The recovery of osmium during the test period was 58 %."

Jan 1, 2018

By Cesar Gomez, Jaime Álvarez, Lisette Wen

Laboratory mechanical flotation cells are extensively used in mineral processing for running batch flotation tests with a variety of purposes, for example assessing feed characteristics, determining flotation kinetics, or testing of new reagents and procedures. It is known that the results obtained depend on the operation mode, self-aerated or forced-air, and on the operating conditions selected for the test, in particular impeller speed and gas flow rate. These different results are a consequence of changes in size distribution of the generated bubble population and its remarkable evolution when frother is added; variations in bubble size affect the bubble surface area flux (BSAF), a variable which correlates with particle collection. Results of a two-phase (air-water) test program designed to measure bubble size for a variety of combinations of impeller type and speed, gas flow rate, frother type and concentration, and cell volume, demonstrated the wide range of BSAF with which the cell can be operated. The results obtained in this work demonstrated that gas dispersion in a forced-air lab flotation machine is significantly affected by the characteristics of the impeller/cell geometry combination in use, and the operating conditions selected. Operating conditions must be carefully selected and maintained during the test to ensure consistent results, in particular when frother concentrations below 20 ppm are used, because frother concentration in the cell will decrease as flotation progresses as a consequence of frother partitioning to the concentrate.

Jan 1, 2014

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 - 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duvalm

Polyethylene glycol monoalkyl ethers (CnEm) render quartz hydrophobic while feldspar remains hydrophilic. As a result quartz can be separated from feldspar in small frothless flotation devices such as the Hallimond tube. The separation can be accomplished at room temperature at pH < 7 and C16E33 concentrations between 10-5 and 10-4 M for quartz particles smaller than 0.4 mm. No separation is observed when feldspar ore containing about 60 % of feldspar and 40% of quartz is subjected to flotation in a laboratory flotation machine. The reason for the lack of separation is a low hydrophobicity of quartz in the presence of polyethylene glycol monoalkyl ethers and high intensity of mixing in the flotation machine. The flotometric tests showed that the contact angle of quartz in monoalkyl ethers of polyethylene glycol solutions is less than about 18 degrees and depends on the structure and concentration of the ether and the pH of the system.

Jan 1, 2003

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By Ghislain Bournival, Seher Ata, Yesenia Saavedra Moreno

"In froth flotation, frothers are commonly added to the pulp to modify the interfacial properties of bubbles. These properties may be modelled using commercial software packages. The volume of fluid (VOF) method was used to track the interface motion during the post-rupture oscillation of the newly formed bubble. The aim of this research was to provide an insight into the modelling of viscoelastic phenomena through the coalescence dynamics of two bubbles in solutions of various surface tensions using a three-dimensional computational study. Different surface tensions were used to simulate changes in methyl isobutyl carbinol (MIBC) concentration. The computational results were evaluated by comparing the oscillatory motion of the newly formed bubble for the different MIBC concentrations. For known MIBC concentrations, the deviations of the computational damping constants from the experiments were quantified, revealing possible deviations in the VOF surface tension model. In addition, the analysis provided insight into the flow patterns of the fluids and the effect of frother concentration on the velocity magnitude in the liquid and air phases. This analysis provided a further understanding of coalescence dynamic and post-rupture oscillation in froth flotation. Such a process is believed to affect the stability of particles at the interface due to the release of surface energy when the bubble surface is reduced.INTRODUCTIONIn froth flotation, bubble coalescence is an important phenomenon that is highly dependent on the interfacial properties of the liquid film between bubbles. It is known that the frother adsorption at the liquid-air interface changes the interfacial properties, resulting in an increase of surface elasticity and reduction of surface energy (Pugh, 2016). However, in a two-phase system, it is the frother type, concentration, frother molecule conformation at the interface and viscoelasticity properties that dictate film stability (Pugh, 2016). The viscoelasticity phenomena can be explained in terms of surface viscosity, which quantifies the energy dissipation at the interface and surface elasticity that represents the energy absorbed at the interface as result of bubble oscillation (Pugh, 2016). In the case of systems stabilized by nonionic frothers, it has been shown that surface forces alone do not account for film stability, but the viscoelasticity represents the ability to damp external disturbances in the thin film separating the bubbles and prevent coalescence (Santini et al., 2007)."

Jan 1, 2018

By Xingshi Yang, Ghislain Bournival, Seher Ata

"Particle-laden interfaces are a fundamental research topic in froth flotation since the process involves particle-coated bubbles in both the pulp and the froth phase. In most experimental studies the characteristics of the particle layer in multi-bubble systems are poorly defined. An experimental setup has been developed based on a Langmuir-Blodgett (L-B) trough. The modified trough allowed introducing an air bubble beneath the particle monolayer formed at the air-water interface which made the study of the interaction between the bubble and the monolayer under various pH values possible. The monolayer characteristics of the particles were also studied and compared in terms of surface pressure (?-A) isotherms and packing factor. On compression, the particles formed branched structure at high pH whereas a uniform monolayer was formed at lower pH. Observations related to the behavior of particles during compression and expansion cycles, and the coalescence of a bare bubble with the flat particle laden interface were provided and the implication of the results for flotation process was discussed.INTRODUCTIONFroth flotation is known for its versatility and ability to concentrate low-grade, complex ores. It is considered a physico-chemical process in which particles attach to air bubbles, depending on their hydrophobicity as well as other factors, and are carried to the surface to form a froth layer. Reagents are used to stabilize bubbles and the froth layer (Pugh, 1996). However, particles, which are carried by the bubbles or entrained, significantly contribute to the stability of the froth phase (Ata et al., 2003; Zanin et al., 2009; Bournival et al., 2015a). Their relevance in mineral processing has led to a number of fundamental studies on the effect of particles and their properties on the process of froth flotation.Flotation systems are particularly difficult to characterize due to the broad range of properties of particles (e.g. size, liberation, hydrophobicity, etc.) and inconsistent operational conditions (e.g. changes in water quality, reagent addition, etc.). Several studies have made the use of well characterized particles in laboratory conditions. Such studies allowed the finding of an optimal contact angle for the stabilization of the froth phase (Johansson and Pugh, 1992; Ata et al., 2002). Froths have a large number of bubbles so that individual interactions are not observed. The study of two bubbles allows to determine the stability of the bubbles, with particles, and to some extend the stability of the bubble-particle aggregate (Gourram-Badri et al., 1997; Bournival et al., 2015b). The removing of particles between two bubbles may also be studied from a Scheludko cell (Johansson and Pugh, 1992) or by observing a bubble with a flat interface (Sethumadhavan et al., 2002). However, these systems provide limited information on the arrangement of the particles."

Jan 1, 2018

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change due to the complex interdependence of metals, both in production and recovery, and the strong path dependency of industry and infrastructure development. Therefore, models for dynamic simulation were constructed that allow the specification and evaluation of the metal process network and waste management infrastructure ‘products’ over a longer time span. The model has been constructed using a bottom-up approach, to enable assessment of the environmental aspects of metallurgy and to simulate changes in the system structure and technology, i.e. from reactor or individual process step up to integrated material cycles. The model comprises hierarchical mass balances and linear models of individual processes and sub-processes. Thus, at lower system aggregate levels an increasing level of technical detail is represented. Data reconciliation has been used literature data on process feed, products and residue composition to calculate representative and reliable split factors around each (sub-)process. World production figures on process capacity and recovery rates are be used to calculate the relative contribution of processes. The dynamic map is illustrated with a case on the introduction of lead-free solder.

Jan 1, 2003

By A. S. Broesder

"With depletion of global ore deposits, there has been an increasing industry trend towards mining of lower average grade deposits in order to meet global demand, resulting in increased processing cost, energy usage and water usage. Consequently the industry is seeking pre-concentration technologies to reduce costs, increase production in existing operations and potentially enable the economic mining of previously uneconomical deposits. This pre-concentration can also advantage downstream processing and metal recovery. CSIRO has developed a large scale magnetic resonance based technology for the rapid quantitative detection of selected copper, iron and arsenic minerals in bulk ore. The technology is suited to measurement on large primary conveyors for enabling “pod” based sorting. The approach used in high tonnage sorting is to not sense and divert individual rocks, but to instead measure groups of rocks (“pods”) carried continuously on a single primary conveyor that can be diverted by conventional mechanical means. Bulk ore sorting operates by removing barren ore pods from a stream of crushed ore based on a bulk sensor measurement at a pod resolution of ~1 – 10 tonnes. The sorting process is based on the intrinsic variability of grade during the mining process that often occurs at the few tonne scale, and for instance, is common in many porphyry copper deposits. The MR technology has been proven in the laboratory for a wide range of copper, arsenic and iron minerals. A full scale prototype sensing system has been demonstrated in a trial at an Australian copper mine. Implementation trials of commercial MR based bulk sorting systems are progressing during 2018.INTRODUCTION An increasing trend in the mining industry is the exploitation of larger lower-grade deposits to meet global demand. Low-grade deposits involve increased processing cost, energy and water usage and increased tailings. There is therefore growing interest in technologies that enable more efficient extraction of low grade deposits. Water intensity of mining activities in a context of water scarcity, and the environmental and health implications of mine tailings are existing challenges, which are only made worse by the progression to lower grade orebodies. There is therefore also an interest in safer, cleaner and less wasteful extraction and production to ensure community well-being and environmental resilience."

Jan 1, 2018

By T. Kalliomäki, B. P. Wilson, M. Lundström, J. Aromaa

"The diffusion rate of cupric ions and limiting current density are important factors that determine the rate of copper mass transport in electrolytes proximal to the electrodes used in electrorefining. As a result, diffusion can critically affect both the rate and morphology of cathodic copper deposition thus it is crucial that it be optimized to improve production. The diffusion coefficient of cupric ion (DCu(II)) in copper electrolytes has been previously researched but the values detailed in the literature show significant variations and moreover arsenic - a common impurity - is generally excluded. Furthermore, in previous studies the models have only been validated with model solutions rather than real industrial electrolytes. In this study, the limiting current density and diffusion coefficient of cupric ion were defined for synthetic electrolytes containing copper (40–60 g/dm3), nickel (0–20 g/dm3), sulfuric acid (130–220 g/dm3) and arsenic (0–45 g/dm3). The cathodic limiting current densities were measured at three temperatures (50, 60, 70 °C) with linear sweep voltammetry using the rotating disc electrode (RDE) as the cathode. By utilizing the limiting current density, models for the DCu(II) were constructed using Levich equation. The validity of the DCu(II) model for technical use was confirmed through their application to industrial electrorefining electrolytes with known element concentrations. Consequently, this study provides improved models for limiting current density and diffusion coefficient of cupric ion that can be utilized for industrial process optimization.INTRODUCTION For an efficient copper electrolysis process, the mass transport of copper ions has to be effective. The main mass transport types of copper ions in copper electrorefining are diffusion and convection while the effect of migration is negligible. In order to maintain good mass transport, it is beneficial to keep both diffusion and convection high to maximize the limiting current density (jlim) (Bard and Faulkner, 2001). jlim is the highest current density that can flow in the cell, thus by maximizing jlim the deposition time can be minimized and the good quality of cathodic copper can be ensured. Thus, it is important to research possibilities that increase and optimize diffusion since slow diffusion in the electrolyte limits the rate of the process (Levich, 1947; Moats et al., 2000; Subbaiah and Das, 1989)."

Jan 1, 2018

By Bern Klein, Givemore Sakuhuni

Flotation is the dominant base metal extraction technique and it requires ore to be ground below the liberation size for effective recovery due to its dependence on mineral surface properties. For a poly-metallic ore, differential hardness of constituent minerals leads to over grinding of softer minerals before the harder minerals are fully liberated, which makes selection of a target grind size complex, and the complexity increases when treating leaner ores. Flotation recovery deteriorates above 100 and below 10 microns causing significant loses of valuable minerals in most flotation circuits. Although enhanced gravity concentration is known to be effective at recovering particles above 100 microns, which are difficult to hydro-dynamically transport, exploiting differential specific gravity for base metal separation was not an option in the past. This was partly due to the absence of high mass yield gravity techniques. The advent of continuous gravity concentrators with flexible mass yields, in the past two decades, has necessitated investigation of possible base metal applications. The Knelson CVD, one of the continuous discharge centrifugal concentrators, has an established application niche for sulphides associated with gold. However, its base metal applications have never been rigorously tested. Considering the dependence of flotation recovery on particle size, continuous discharge centrifugal concentration can be integrated in flotation circuits to capture flotation non-recoverable coarse particles. This paper explores how particle size, liberation and mineral hardness influence application of continuous centrifugal technology to regulate galena deportment in a polymetallic base metal plant. The results show that particle size affects galena recovery more than liberation. In view of these results, the CVD can be integrated in the primary grinding circuit to pre-concentrate the heavy sulphides at a coarser grind size with potential grinding energy savings.

Jan 1, 2014

By P. Somasundaran, Tarun Bhambhani, S. Murthy Khandrika, Partha Patra, D. Nagaraj

Fine and ultrafine mineral particles, particularly if, altered mineralogically, can have detrimental effects on selective separation of minerals. Behaviour of altered mineral fines has been investigated in this work by studying the effects of weathered silicate slimes on the selective separation of copper minerals, particularly with focues on effect of the pulp rheological behaviour, which plays a governing role in the process. Physicochemical properties of these altered silicates fines such as morphology and surface charge are proposed to be responsible for the adverse rheological effects and resultant selective separation. Here, the effect of a number of problematic aspects such as water chemistry, froth stability, physicochemical aspects of gangue mineral aggregates on flotation sub-processes has been studied. Processing problems owing to the physical aspects of the gangue minerals, shape and morphology, are primarily due to uncharacteristic increase in the pulp viscosity. While problematic aspects other than impact of pulp rheological behaviour can interfere with each other in their contributions to how they affect the sub-processes, effects owing to pulp rheological behaviour have a direct impact on the flotation performance. Subtle increase in pulp viscosity can interfere with sub-processes in flotation leading to decrease in recovery and grade, and it is difficult to assess the effects due to such subtle changes. Reagent based strategies to overcome the problematic aspects has been explored here.

Jan 1, 2014

By Bern Klein, Givemore Sakuhuni, Libin Tong

The use of continuous discharge centrifugal concentrators introduced in the early 1990’s for recovery of gold associated with sulphides has introduced a novel application niche for gravity concentration which could not be realized with the low mass yield batch and semi-continuous concentrators. A typical application is scavenging gold associated with sulphides from flotation tails which has potential to increase productivity by reducing gold loss to tailings and lower grinding cost by using a coarser grind. However, the full potential of this technology has not been fully exploited partly due to the lack of reliable small sample procedures to demonstrate applicability. This paper introduces a bench-scale procedure developed to characterize the Knelson Continuous Variable Discharge concentrator (CVD) for scavenging gold from flotation tails. The procedure code named gravity release analysis was derived from standard flotation release analysis. It is a modification of the gravity recoverable gold and gravity amenability test in order to best simulate continuous centrifugal concentration. Based on this iterative procedure, a gravity release index similar to the flotation rate constant, for measuring individual mineral gravity susceptibility for an ore is introduced which can be a useful quantitative measure to both predict application of centrifugal concentration and for plant design. The gravity release analysis procedure was tested on a polymetallic flotation plant tailing at Myra Falls, BC, Canada and results show that it can predict CVD performance. The gravity release index for gold was observed to decrease with each successive cleaner stage showing that the initial stages recover liberated gold whilst successive runs recover gold associated with sulphides and or gangue. The difference in magnitude of the gravity release index for different mineral species shows the species separable by centrifugal concentration.

Jan 1, 2014

By Scott C. Brown, Brij M. Moudgil, Ivan U. Vakarelski

The manipulation of the apparent hydrophobicity of particlute surfaces is necessary to achieve optimal selectivity in flotation processes. Previously a number of works have investigated the role of microscale surface and particulate morphologies on chemically modified substrates. These works have suggested that microscale surface asperities lead to an increase in flotation efficiency by assisting in the rupture of wetting films. Yet, in mineral processing the presence of surface asperities may lead to a reduction in flotation. The reason for this may-in part-be due to the presence of nanoscale irregularities at the interface. In this work, it is proposed that the presence of roughness at the nanoscale may have a dominant impact on the apparent hydrophobicity of mineral surfaces during flotation. It is suggested that as inter-asperity seperation distances are reduced capillary effects are enhanced for high energy mineral surfaces leading to the formation of liquid domains, which adversely impact hydrophobicity. In addition, as these distances approach the surfactant headgroup size obstruction of surfactant self-assembly process may occur, thereby further limiting flotation.

Jan 1, 2003

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014