Search Documents

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 µm to 150 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2014

By D. J. Borrow, K. van Netten

"A fine coal tailings feed was selectively agglomerated using a concentrated water in oil emulsion binder consisting of 95% aqueous phase and 5% organic phase. The purpose of the study was to investigate a continuous system in plug flow, providing a rapid beneficiation technique with high selectivity and recovery. The development of the novel binder was undertaken in previous work in a batch system consisting of a high-speed blender. In this previous work, it was found that agglomeration could be achieved in 3 s, providing the binder was pre-dispersed. Furthermore, it was found that, depending on the feed, only ~1 wt% of oil was required to achieve agglomeration, some 10 times less than required in traditional oil agglomeration. In a more recent study, the technique was adapted into a continuous process. Due to the rapid speed of the process using the emulsion binder it was found that a simple flow constriction within a 1 inch pipe was sufficient to achieve the selective agglomeration observed in the batch system. In this previous study, a coal feed consisting of a flotation product was agglomerated at a superficial slurry velocity of 1.3 m/s using a partially closed ball valve as the flow constriction. In the current study, a feed consisting of fine coal tailings with an ash content of 50.1% was used to establish the influence of superficial slurry velocity on the agglomeration process. The superficial slurry velocity was varied between 1.3- 4.2 m/s, while maintaining a constant pressure drop of 100 kPa across the flow constriction. The flow constriction consisted of a partially closed ball valve. It was found that increasing the superficial slurry velocity across the flow constriction reduced the amount of organic liquid required to achieve agglomeration. Under the optimum conditions, a combustible recovery of 80.4% was achieved at a product ash content of 9.6%. This work demonstrates a valuable product can be rapidly produced from tailings material using the novel emulsion binder. INTRODUCTION A significant opportunity exists to recover fine coal from material that is currently classified as waste. This waste material, also called tailings, is currently considered not economic to process due to its high ash content, low solids concentration, and the fine size of the particles. Thus, for this opportunity to be realised, a process is required that is highly selective and has the ability to economically recover fine particles at high throughputs. The technique of oil agglomeration has previously been considered as a candidate for the recovery of fine coal, as it is highly selective and has no lower limit on the size of particle that can be recovered (Capes and Jonasson, 1989). However, the cost of the oil required as the binding agent in the process has proven to be a significant barrier to any long-term applications (Swanson, Nicol, and Bensley, 1977). Recently, however, Yoon and co-workers have developed an ultrafine coal separation process that utilizes an oil phase for the recovery of the hydrophobic coal particles and have implemented an oil recycle to greatly reduce the consumption and thus cost of the oil (Yoon et al., 2016)."

Jan 1, 2018

By V. F. Petrov

Today, sodium cyanide is extensively used for extracting gold, however it is highly toxic to the environment if not managed properly. This paper discusses the key challenges presented to gold operations in efforts to come into alignment with the Russian environmental regulations and suggests solutions to overcome these challenges. It is a fact that the major environmental threat cyanide poses to water sources. Therefore, natural water sources should be well protected from the adverse effect of cyanides used in hydrometallurgical processes. For this, the following site procedures and facilities are practiced: in-site and external water recycling systems, reclaim water treatment if required and tailings ponds with water impermeable screens (tailings ponds with controlled leakage). Cost comparison analysis of cyanide destruction methods was carried out. It was revealed that the aldehyde treatment method developed by Irgiredmet JSC demonstrated the best economics. Cyanide emissions are treated by mass-manufactured packed and membrane devices which allow to keep cyanides at the acceptable limiting values established by environmental regulatory agencies.

Jan 1, 2014

By Ivan Bonchev, Elisaveta Djurova, Evgeni Visariev, Viktor Stoilov

"Two types of slag cooling is used world wide - cooling in ladles and cooling in pits. The flotation comparison of the type cooling regimes was done at Aurubis Bulgaria. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag flotation plant processes blend of three parts FSF and one part converter slag. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper content in flotation concentrate is over 20 % and in flotation tail is under 0.5 %. In order to improve the copper recovery, different cooling rate of the liquid slags should be achieved. Three cooling experiments with flash smelting furnace (FSF) slag have been done: two of them in pits with different volume and one cooling experiment in metallic ladle. The ambient air temperature during the cooling tests was from -4 to +4 OC. Laboratory flotation tests in open cycle were done with an aim to compare the slags behaviors cooled at different conditions. In this paper the effect of different cooling on the flotation process will be presented. The copper recovery and distribution by sizes in the tails, copper content in the rougher concentrate, and the concentrate yield are discussed."

Jan 1, 2014

By T. Fujita

The incinerated bottom ash includes titanium oxides and a small amount of chromium oxides. Initially, 89 % of chromium was removed from ash at magnetic flux density at several stages of wet magnetic separation from 0.05 T to 6 T. The bottom ash from an industrial waste incineration process includes about 10 % of TiO2. The minerals that contain titanium are rutile and perovskite. These minerals are paramagnetic and show low magnetic susceptibility, therefore, the high magnetic field strength, created by a superconducting magnet, is necessary to capture these minerals. At the first stage of separation, a magnetic field strength of 6T was applied in order to attract the particles that contain iron oxides to the higher magnetic field region. At the second stage of separation, the magnetic capture rate of weekly magnetic particles decreased with increasing the magnetic susceptibility of the aqueous solution (i.e. the medium for dispersing the particles) in order to separate the highly magnetic materials. The para-magnetic salt such as ferric chloride was dissolved in the water to increase the magnetic susceptibility of the medium. After a two-step wet HGMS with superconducting magnet, the grade of TiO2was increased from 10 % to 28 % with a recovery of 64 %.

Jan 1, 2014

By L. Burdukova

"In flotation, depressants are used to reduce the amount of gangue that reports to the concentrate and hence increase the selectivity of the flotation process. At the University of Cape Town extensive batch flotation tests are carried out to evaluate industrial depressants and standard procedures have been developed over the years.This study was conducted in order to develop an improved method for comparing depressants using machine vision as an aid. The modified method of batch flotation involved a test with prolonged intervals between scraping to allow more time for the froth to build up and mature.This method of testing showed increased differences between the flotation performance obtained as represented by grade recovery curves for carboxymethyl cellulose and guar depressants when compared to the standard method of testing with shorter scraping intervals. The improvement was attributed to reduced entrainment resulting from longer drainage time in the froth and therefore yielded a better test for comparing depressants on the basis of true gangue flotation with minimized entrainment. As expected, the sulphide recoveries were unaffected by the change in method. The machine vision system also added to the information obtained during these tests by recording bubble size trends throughout the tests which were later analyzed and related to the amount of flotable gangue in the froth. Modifications are recommended to improve the usefulness of machine vision in batch flotation."

Jan 1, 2003

By A. Kamali Moaveni, A. Boehm

"The current research study addresses a physical separation process of basic oxygen furnace slag “BOF-Slag” (also called Linz-Donawitz “LD” slag) for the removal of phosphorous. In order to recycle the LD-Slag into the steelmaking process, the physical dephosphorization methods are considered. The systematic geometallurgical investigation carried out on particle classes of decreasing size, which were further subdivided into susceptibility classes, shows intimate intergrowth beyond 40 µm due to slag´s fast cooling rate. Generally, LD-slag is constituted of oxide and silicate phases, among which di-calcium silicate “C2S” dominates. About 0.5 mass% of phosphorous was detected in the LD- slag, which is exclusively situated in the lattice of the C2S. The comparatively high grinding resistance (Rittinger index 12.9 cm²/J) of the LD-slag reflects the energy demand to liberate the phosphorous carrying phase from the iron containing minerals, while separation efficiency decreases in the very fine particle size range. Hence, the conversion of the phase intergrowth pattern was considered alternatively to re-build the mineral phase structure of the material to a separable interlock pattern. Carbon dioxide, as the most convenient substance in the steelmaking plants, was applied to digest the C2S in the presence of water and to reduce the basicity of the slag slurry. As a result of C2S-CO2 chemical reaction, calcite and calcium silicate are precipitated at the surface of the oxide particles and carried between 25% and 75% of the total phosphorous, respectively. Accordingly, the mobility of the phosphorous content phase to the top of the grains serves the possibility to separate the precipitated layer by mechanical attrition process. This paper is focused on the impact of the intergrowth pattern alteration on the slag´s separability characteristics. Moreover, the operating conditions of the carbonization process, such as temperature and pressure, on the deconstruction kinetics of the C2S and the generated products will be considered. INTRODUCTION The steelmaking BOF-Slag is a stony aggregate waste from the steel manufacturing process. The investigated slag by the current research work was provided by voestalpine steelmaking plant in Linz, Austria. The current legislative situation in Austria restricts the historical application of slag as construction material, due to the high level of heavy metals content and corresponded land-filling and transportation costs of slag, therefore the demand for recycling of BOF-Slag to the steelmaking process has raised, as an alternative application. Statistically, voestalpine steelmaking plant produces about 130 kg BOF-Slag per ton of final steel product, which serves annual BOF-Slag production of 700,000 ton, approximately."

Jan 1, 2018

By A. V. Myaskov, V. S. Valavin, K. D’Elia, I. O. Krylov, Vu Van Toan, T. I. Yushina

"The purpose of this research is the development of a technology for processing the concentration tailings of limonite ores at Kamysh-Burun Mining and Processing Complex into an iron- containing product for ROMELT process. In the concentration and metallurgical processing of iron ores, substantial amounts of waste are generated (tailings, slimes, slags, metallurgical dust, etc.) that can be converted into a commercial product if is properly processed. This article presents the results of experimental studies of the feasibility of processing iron- containing tailings of Kamysh-Burun deposit (slimes from Verkhne-Churbash storage facility (VCh sample) and dumped waste of Kamysh-Burun (KB sample)) to obtaining valuable components for further uses. Applying Mossbauer spectroscopy has been shown that the iron minerals in the studied samples are technogenic varieties of iron hydroxides. The most suitable technology is the magnetic roasting process, since iron hydroxides are easily transformed into a magnetic, easily recoverable form. Have been shown the advantages of a two-stage magnetic separation, in a strong field and with polygradient separators. Concentrating this material through magnetic methods makes it possible to increase the iron content to 20-21 %. Magnetic concentration of the deeper layers materials results in iron- containing concentrates with a total iron content of up to 58% whit a phosphorus content of about 2%. Reducing the phosphorus content is possible by blending upper and lower layers of the material at a ratio of 1:1. Thus, it is possible to process the material accumulated in the slime storage facility using the ROMELT process combined with preliminary three-stage magnetic concentration and disposal of tailings with the permissible iron content of less than 5%. Wastes from smelting will be slags suitable for use in construction industry. The Kamysh-Burun material preparation for ROMELT process should be performed applying gravity-washing with separation of the -0.4 mm fraction and additional blending for dephosphorizing the concentrate. The smelting will produce pig iron and slag."

Jan 1, 2018

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By Peter Scales, Ricardo Jeldres, Fernando Concha, Pedro Toledo, Shane Usher, Anthony Stickland

The impact of several electrolytes present in seawater on the rheological properties of flocculated mineral suspensions was assessed using the creep test. Flocculated suspensions were obtained by adding polymer flocculant to a cylinder of mineral suspension and aggregating the suspension using the plunger method. The suspension was allowed to sediment and the supernatant liquid decanted prior to tests for the viscoelastic properties of the resulting sediment. The solid used was alumina AKP-30 both, below and above the isoelectric point. The polymer used was AN934SH, an anionic flocculant with high molecular weight. Salts analyzed were MgCl2, CaCl2 and NaCl, known as water structure makers, and KI and KCl, known as water structure breakers. A high salt concentration of 0.5 M was used to approach the ionic strength of seawater. For both pH’s studied, the sediments demonstrated a viscoelastic non-linear behavior observed as a non-linear relationship between yield strain and applied stress. In the absence of flocculant, it was observed that the viscosity and yield stress of a suspension increase in the presence of structure maker salts for the case of both silica suspensions and alumina suspensions. These results were explained using hypernetted chain statistical mechanics models describing the interaction of ions with solvated surfaces. In contrast, with the presence of flocculant, the shear yield strain of alumina suspensions increases with the breaker character of the salts, however, this result has been explained by an extension of the results from the models. The work has significant implications for the flocculation of mineral suspensions in the presence of seawater.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By D. Vega, P. R. Brito-Parada

"Small diameter (10 mm) hydrocyclones have been applied successfully for the separation of particle suspensions in the micron size range. These hydrocyclones are attractive because they show a bypass fraction larger that the water recovery, resulting in a high particle recovery to the underflow as well as low water recovery. However, this is a disadvantage when the purpose of the hydrocyclone is classification because of the large amount of fine particles that are misplaced in the underflow. The aim of this study is to explore, experimentally and computationally, the influence of design parameters on the classification process. In this work, a full factorial experimental design was defined to carry out comprehensive experimental tests using glass beads (0-20 µm) as the particulate system. We show that the dimensions of spigot and vortex finder diameter can be effectively manipulated to change the separation performance of the system and the energy consumption. A CFD model was developed that is able to predict particle size distribution. The numerical results for the partition curves showed very good agreement with the experimental data. INTRODUCTION Small diameter hydrocyclones are a very attractive separation technology for fine particle suspensions. Since the hydrocyclone diameter is directly proportional to the cutsize that can be achieved, 10mm hydrocyclones have been shown to be very effective in collecting particles in the micron-size range. In addition, while in large hydrocyclones the bypass, i.e. the fraction of particles that report to the underflow without classification, is similar to the water recovery, in 10mm hydrocyclones the bypass fraction is considerably larger than the water recovery. Its high particle recovery and low water recovery makes small hydrocyclones ideal for ultrafine particle classification and dewatering applications in mineral processing. The separation of mineral suspensions achieved using small hydrocyclones has been the focus of various studies. Pasquier and Cilliers (2000) derived a general classification model from experimental data of fine silica concentration in 10mm hydrocyclones; the model was able to describe the fish-hook partition curve. The effect of operating conditions has also received some attention in the literature. Cilliers et al. (2004) showed that an increase in temperature positively effects the recovery of fine silica particles in small hydrocyclones, by increasing the bypass and decreasing the cutsize. Neese et al. (2015) showed that the cutsize in 10mm hydrocyclones can be further decreased by operating at higher pressure, which also trebled the throughput."

Jan 1, 2018

By Hillary Williams, Ronghao Li, Christopher Marion, Kristian E. Waters, Devin Hundt

"Zircon is an important mineral for ceramic, foundry, casting, and refractory applications; and it is the worlds primary source for zirconium. Zircon can also contain large and valuable proportions of other valuable metals, such as rare earth elements and hafnium. The Nechalcho deposit (Northwest Territories, Canad), is a hard rock REE deposit, which looks to recover zircon for its Zr and REE content. In this deposit, zircon is finely disseminated and associated with predominately silicate gangue minerals. Most of the work to date has focused on the beneficiation of mineral sand deposit, which typically remove silicate gangue minerals through physical separation steps. Therefore, the separation of zircon from silicate gangue, such as quartz, by flotation, has received little attention. This work used zeta potential measurements and microflotation experiments to understand the interaction between zircon and six different collectors (sodium oleate, sodium dodecyl sulphate, dodecylamine, SM 15, K-octyl hydroxamate and Florrea 7510). The results were compared with those of quartz. This study indicated that selective separation of zircon from quartz without the use of selective depressants or activators is likely challenging. The findings suggested sodium oleate and SM 15 only offered selective flotation of zircon in highly acidic conditions. Separation by the flotation of quartz is possible using sodium dodecyl sulphate, dodecylamine and K-octylhydroxamate. However, selective separation is highly dependant on collector dosage, for dodecylamine, and the selective activation of quartz, for sodium dodecyl sulphate and K-octyl hydroximate. Florrea 7510 offered poor recoveries for both zircon and quartz.INTRODUCTIONZircon (ZrSiO2) is a nesosilicate mineral which has a wide variety of applications, due to its hardness, opaqueness and resistance to heat and corrosion. Its major end uses are in ceramic, foundry, casting, and refractory applications (Bedinger, 2017). Zircon is also the most abundant zirconium (Zr) bearing mineral in the earths crust and is the principal economic source of Zr (primarily used in alloys for heat and corrosion resistance) and zirconia (ZrO2) (primarily used in ceramics) (Bedinger, 2017; Milnes and Fitzpatrick, 1989). Zircon forms in silicate melts and can often contain large proportions of other valuable metals such as rare earth elements (REE), and hafnium (zircon is the primary source of hafnium) (Bedinger, 2017; Belousova et al., 2002; Orlova, 2007). A common chemical formula showing the range of substitution in zircon is (Zr,Hf,Th,U,REE,Ca,Fe,Nb,Ta)(Si,P)O4 (Orlova, 2007)."

Jan 1, 2018

By Wei Zhang, Jinhong Zhang

"In froth flotation, the adsorption of collector on mineral surface is critical for a successful flotation process. In present work, an atomic force microscopy (AFM) has been applied to study the adsorption of potassium amyl xanthate (PAX) on copper sulfides, i.e., chalcopyrite, chalcocite and bornite. The in-situ collected AFM images show that PAX adsorbs on chalcopyrite mainly in the form of oily dixanthogen; while it strongly adsorbs on chalcocite and bornite in the form of insoluble metal xanthate, which binds strongly with the mineral surface. The information obtained from the AFM study shed lights on the collectivity and therefore the selection of specific collector for different copper sulfide minerals in industrial practice.INTRODUCTIONFroth flotation, which treats the highest throughput in mining industry and produces the maximum economic outcome of any surface chemistry process, has been widely applied for the concentration of copper sulfide minerals, i.e., chalcopyrite, chalcocite and bornite. In flotation, collectors are added into the pulp (mixture of water and fine-grained minerals) to selectively adsorb onto the target mineral and render its surface with high hydrophobicity, which is generally beneficial for a strong mineral-bubble attachment and thus a high flotation recovery. Therefore, the adsorption of collector on mineral surface is vital for a successful flotation process and it has been studied by applying various surface analysis techniques, such as IR (Infrared Spectroscopy), CV (Cyclic Voltammetry) and XPS (X-ray Photoelectron Spectroscopy). (Poling, 1963; Allison et al., 1972; Mielczarski et al., 1984; Leppinen et al., 1989; Kartio et al., 1996) These studies have revealed a lot of information, such as the reaction, product and mechanism, of the adsorption of chemicals on mineral surface. It is also of great interest to directly get the image of adsorbed collectors on mineral surface changing with pulp chemistry, such as pH, redox potential, ionic strength and chemical’s dosage."

Jan 1, 2018

By Andrew T. McBride, Malcolm S. Powell, Indresan Govender

"Current empirical Semi Autogneous Grinding (SAG) mill models contain assumptions concerning the amount of energy available for particle breakage, how this energy is distributed in the mill media and the rate at which the energy is transferred. Despite these assumptions the JK SAG model is highly functional with a proven track record. DEM provides a numerical framework to greatly improve on these assumptions that were necessary due to a lack of available input data.This paper identifies key outputs of the Discrete Element Method (DEM), such as energy spectra and impact probability distribution. It describes how they can be incorporated into current mill models utilising practical rock breakage data. The rate at which energy is transferred is shown to be dependent on particle position and mill rotational speed and not once per cycle as previously assumed. Based upon this an improved energy transfer methodology is presented. The fundamental outputs of the DEM are validated against experimental three-dimensional particle tracking data, so as to establish whether the DEM produces correct energy transfer predictions on the inter-particle level, which is crucial to this work."

Jan 1, 2003

By Amir Hajizadeh Omran, Mehdi Irannajad, Sima Mohammadnejad, Fardis Nakhaei

"This study presents an experimental program performed to investigate the effects of flotation variables including gas flow rate, froth depth, slurry solids percent, frother/collector dosage and pH on the froth bubble size during desulfurization of an iron ore. These conditions were varied using a central composite design (CCD). Image analysis techniques have been developed and used successfully to characterize the froth bubble size. Results of the CCD experiments showed that the flotation variables have different effects on the froth bubble size. The froth height, air flowrate, pH and solid content had the most important influence on the froth bubble size. The interaction between the collector-frother, pH-collector, frother-air flowrate, solid content-froth height, pH-froth height and solid content-pH were also significant. Process state can be accurately deduced from the froth surface appearance, providing a convenient way to quantify the parameters as a function of the process control. INTRODUCTION Flotation processes are subjected to a wide variety of process disturbances, some of which are made by the change in mineral features and others to variation in operating procedures. Feed and air flow rates, densities, size distributions and shapes of particles, surface properties, and reagent dosages and compositions can all change, often with significant effect on the performance of the plant (Moolman et al., 1996a). Flotation process efficiency is governed by the wettability of the solid as well as the surface tension at the liquid-gas. Both of these properties are influenced by operational conditions encountering in a flotation process. The structure of froths developed on the pulp surfaces of flotation cells has a remarkable effect on both the grade and recovery of minerals in the concentrate (Shean and Cilliers, 2011)."

Jan 1, 2018

By G. Önal

Recovery of nickel and chromite from the tailings has been studied on the samples with 0.214 % Ni and 5.10 % Cr2O3 content and taken from Orhaneli Chromite Concentration Plant. Mineralogical examinations of the samples showed the existence of chromite, olivine, pyroxene, chrysotile, anti-gorite, chlorite, idingite, tremolite and calcite together with trace amounts of millerite, pentlandite, pyrite, pyrrhotite, hematite and limonite type iron oxide minerals in partially serpantinized dunite type particles. In order to recover chromite from Chromite Concentration Plant tailings Mozley Table and Knelson Separator are used and concentrates containing approximately 42% and 46% Cr2O3 are produced respectively with 40% recovery. Most of the nickel remained in the tailings. Therefore, acidic leaching tests are performed in order to dissolve nickel from these tailings. Effects of particle size, acid concentration, temperature, leaching time and solid/liquid ratio on the nickel leaching efficiency are investigated. The optimum leaching conditions are found as 250 g/L acid concentration, 1/5 solid/liquid ratio, 2 hours of leaching time and 60°C temperature, almost all nickel is dissolved at the optimum conditions and acid consumption is about 841 kg/t. Repeated leaching tests are carried out in order to have enough Ni content in the leach liquor for the further treatment of solutions. After repeated leaching tests, leach liquor contains 3 kg/m3 Ni, 48 kg/m3 Fe, 2.2 kg/m3 Si, 23 g/m3 Cr and 590 kg/m3 H2SO4. Ni is recovered from that solution by precipitating with H2S followed by HNO3 dissolution and precipitating Ni as hydroxide with 63% Ni content. Leach cakes are subjected to the gravity separation (Mozley table) to recover the remained chromite and a chromite concentrate with 47% Cr2O 3 content is produced with 53% recovery. As a result of the abovementioned tests, a conceptual process flow sheet is proposed for the treatment of these chromite concentration plant tailings.

Jan 1, 2014

By József Faitli, Imre Gombköto, Barnabás Csoke, Tamás Magyar, Beáta Oláh, Sándor Nagy

"Raw materials are among the main building blocks of a growing economy. Without raw materials, no matter whether it is primary or secondary, production is not possible. Products with high added value require special materials. Recently, worldwide production of some important raw materials mainly comes from a handful of countries, for example: China (Rare Earths Elements (REE)), Russia, South Africa (Platinum Group Elements (PGE)), Democratic Republic of Congo (Cobalt), etc. In the EU as well as in Hungary, the importance of the so called 14 critical raw materials has been recognized. Within the frame of the TÁMOP-4.2.2.A-11/1/KONV-2012-0005 - CriticEL project, the Institute of Raw Materials Preparation and Environmental Processing in cooperation with the Institute of Mineralogy and Geology of the University of Miskolc are working on the exploration of the primary and secondary sources and developing innovative preparation technologies of critical raw materials in Hungary. The research work showed in this article, focused on the recovery of critical materials from LCD TVs and monitors. There are high deviations in different literatures regarding to concentrations of critical elements in displays (e.g.: indium), probably because of the differences in production year, producers and recovery technologies. During the research - described in this study - a well specified sample of quite large amount of displays had been used. The exact place and shape of the ITO (indium-tin oxide) layer were determined by SEM analysis. The applied preparation technology was developed based on the results of our investigations and by technologies found in the literature. The developed process accomplishes two main parts: the mechanical preparation (mainly the liberation of different display layers, removal of liquid crystal) and the acidic dissolution of indium."

Jan 1, 2014

By M. Rudolph, E. Schach, M. Buchmann, T. Leißner, N. Krupko, U. Peuker, M. Kern

"In mineral processing, density and magnetic susceptibility are two very fundamental properties. For the beneficiation of valuables to produce a saleable concentrate a detailed understanding of these properties is essential. Especially when it comes to the processing of cassiterite, which is the main mineral for tin production, they become highly prominent. Due to the chemically inert character of cassiterite towards most industrial applied leaching agents, density and magnetic separation processes are mainly applied for its beneficiation. To guarantee an optimized utilization of the different operations not only cassiterite but also the different gangue minerals have to be considered. In this study, a skarn ore is characterized by density and magnetic susceptibility. Therefore, the material was first split into different density classes by heavy liquid separation. The obtained classes were further separated by their susceptibility to finally obtain a density-susceptibility matrix. For this purpose, an isodynamic separator was used. A more detailed characterization of the materials is done via gas pycnometer, magnetic susceptibility balance and vibrating sample magnetometer to estimate the characteristics of density and susceptibility for the various classes. Further, the determination of the chemical assay and the mineral intergrowth by mineral liberation analysis is used to generate a three dimensional database for detailed characterization of the present ore. The objective of this study is to estimate potential material streams for a modular processing plant via characterization of the material for the entire deposit by the two afore mentioned characteristic properties. The established multidimensional data matrix, enables predictions for the separation properties of the material and contributes to the characterization of the deposit within the context of geometallurgy."

Jan 1, 2018

By Jin Duan, Qi Zheng, Bo Yan, Li-cheng Ma, Xiao-kui Che

"The aim of this study was to develop an approach for the selectively removal of Zn(II) from heavy metal-bearing-wastewaters produced by gold chemical industry using magnetic chitosan based adsorbents. Chitosan beads were prepared by cross-linked modification of Fe3O4-chitosan bead using epichlorohydrin as the cross-linker. Both Zn(II) inprinted magnetic chitosan hydrogel bead (Zn-MCHB) and unprinted magnetic chitosan hydrogel bead (MCHB) were prepared and batch adsorption experiments were used to evaluate their adsorption capacities and selectivities. Single adsorption of Cu2+, Pb2+, Zn2+ and Ni2+ showed that both MCHB and Zn-MCHB adsorbs all the four metals and had an affinity in the order of Cu2+ > Pb2+ > Zn2+ > Ni2+. The binary adsorption revealed that the two adsorbents preferentially adsorb Cu2+/Pb2+ from Zn2+-Cu2+/ Zn2+-Pb2+ binary systems. However, MCHB does not show any selectivity in Zn2+-Ni2+ system. In contrast, Zn- MCHB preferentially adsorbs Zn2+ from Zn2+-Ni2+ binary system. Furthermore, the adsorption selectivity is predictable from stability constants of the metals with the amino group of chitosan. The information revealed in this work can be used for further applications in the treatment of wastewater containing a range of heavy metals from the gold chemical industry."

Jan 1, 2014