Search Documents

By M. Saghaeian, R. Hejazi, M. Mohammadinejad, M. Zare

"Water quality and quantity at the Tailing Thickening Section of processing plants is considered to be a crucial factor and impacts the performance of several sections. Therefore, gaining stable and effective performance at the Tailing Thickener Section is one of the principal goals of minerals processing plants. Different factors such as: qualitative and quantitative sustainability of plant feed, the balance between the mass of input and output water flow, the dissolving method and distribution of flocculant and the amount of dirt, solid percent of thickener inlet pulp, affect the performance of Tailing Thickener. The present study investigates the successful improvement of Tailing Thickener performance at Jalal Abad Hematite Iron Ore Concentrate plant through optimizing the above operational parameters. For this purpose, the following optimizations have been done: homogeneity and sustainability of plant input feed rates, fine pulp removal collected by the bag filters at the input of the thickener, adding an quietness box before moving the tail pulp into the thickener to reduce the pulp turbulence, replacing flocculant pump and injection pipes, improving water mass balance which leads to optimizing and stabilizing the concentration of input tail pulp into the thickener, adding a mixer to increase the flocculant preparation time, increasing the locations for adding flocculant to thickener from 1 point to 6 points. Applying the above modifications and monitoring the Tailing Thickener performance over the course of months, has led to the improvement of recovered water quality from 500 ppm to 200 ppm, increasing the solid underflow of the thickener from 40% to 48.5%, and similarly, reducing water loss by 60%. Of other important effects, due to improvement of water quality, grade of final concentrate 0.5% increased and because of 73% increase in monthly working hour, concentrate tonnage 55% increased. Finally, sludge thickener optimization has had a significant effect in selecting and designing the dewatering system from the underflow of the sludge thickener."

Jan 1, 2018

By H. L. Liu

With the exploitation of mineral resources, valuable minerals are more and more finer and poorer. Priority reclaiming liberation grind particle under rough grinding, will help to pervert loss of melts, raise dewatering efficiency of concentrate, reduce consumption of reagent. And it is propitious to reduce energy consumption and raise the utilization rate of resources. With the feature of coarse particle?s desorption and deposition, CLF flotation machine has special pulp circulating way, which is not only apply to treat coarse particle but also normal size particle. The paper advanced the history, the design principle, the structure feature and the application of CLF flotation machine.

Jan 1, 2014

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By H. J. Schulze

From a colloidal science point of view (Schulze 1984, Nguyen & Schulze, 2004) five micro-processes are responsible for successful particle-bubble formation: the approaching of the particle to the liquid-air interface, the thinning and rupture of the intervening liquid film, the expansion of the three phase contact perimeter, the generation of sufficient large capillary force to stabilise the aggregates and the transport process of particles into and within the froth layer. Flotation reagents influence mainly the thinning and rupture of the intervening liquid film between particles and air bubbles, the expansion of the three phase contact after the rupture of the liquid film and the stability of the aggregates against external destruction forces in the flow field. But it exist also a non-negligible influence on the approaching of particles to the bubble surface during the encounter process and on their passing over into the froth layer and the froth stability.

Jan 1, 2003

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By G. Mucsi

This paper deals with the laboratory investigation of cathode ray tube (CRT) glass based glass foam, a relatively new product so called ?Geofil bubbles?. The main process engineering material properties of raw materials, such as particle size distribution, moisture content, density and specific surface area are shown. Then the preparation of raw cathode ray tube glass waste is presented including the following steps: crushing in impact crusher, grinding in laboratory scale ball mill, mixing, pelleting and sintering. We found that it was possible to produce foam glass (with proper mechanical stability and particle density) from the investigated waste CRT glass. The material characteristics of the final product strongly depend on the sintering conditions. Optimum conditions were determined particle size fraction was found to be 4-6 mm, temperature 800 0C, residence time 7.5 min. Keywords: waste CRT glass, grinding, pelleting, sintering, glass foam

Sep 1, 2012

By Z. Naziemiec

Since several years in Poland a huge demands on mineral aggregates occur, for the reason of intensive development of housing and road industry, as well as industrial building. Limitations in re-sources of broken aggregates in Central and Northern parts of Poland cause, that both the non-waste production of aggregates with high quality and the production of alternative aggregates from recycling gain greater importance, nowadays. It entails increase in demands for crushing devices, which are easy and reliable in operating as well as inexpensive and enabling to obtain a good quality products. Jaw crusher, regarded as the most spread in Polish industry, meet these requirements, however, their crucial disadvantage is a large content of irregular grains in crushing products. Numerous investigations show, that the shape of grains is a significant feature of aggregates, which influences on durability and quality of produced concretes. The advantage of jaw crushers is their easy operation, low price as well as low amount of dusts (wastes) generated in comminution products in comparison to other types of crushers (i.e. hammer crushers).

Jan 1, 2014

By B. Friedrich, A. Weyhe, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990’s. Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used today in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals (RE) are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process described in this paper consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps. This process is capable of treating all types of Ni-MH-batteries. After comminution steel and organics are separated. The separated Ni-MH is smelted in an electric arc furnace. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’. Both the Nickel-Cobalt alloy and the ‘mischmetal’ will be directly used in battery production."

Jan 1, 2003

By E. Scheepers

The process under investigation is the large-scale production of phosphorus. Gravity delivers the feed, consisting of pelletised apatite, coke and silica (in the form of gravel), to a submerged arc furnace through ten, evenly distributed feed chutes ensuring constant packed bed volume. Within this packed bed, solid-gas reactions are dominant in generating the gaseous product. These reactions, as well as the packed bed itself, were the main focus in the development of a fully three-dimensional CFD model in which fluid flow and energy distribution are represented as functions of chemical reactions, heating and melting of material and heat losses. The associated complex process interactions necessitated the creation of two process-specific, user-developed models that integrates accurate, thermodynamical data with computational fluid dynamics calculations, as well as reaction kinetics. The boundary conditions are provided by industrial measurements, and the key model parameters of reaction kinetics were obtained by laboratory experiments for different feed mixtures. Thirteen temperature probes installed inside the refractory lining of the furnace especially for this project allowed parameter fitting and validation to be guided within the constraints of real measurements. Simulation results reveal a thin, dome-shaped, reductive zone where conditions are optimum for maximum phosphorus recovery, as well as evidence of a thermal reserve zone similar to an ironmaking blast furnace located above this reduction zone. When compared to actual operating data, the CFD model can successfully predict the specific power consumption, the phosphorus in the slag and gaseous product flowrate under given operating conditions. This CFD model forms part of a larger project that aims to create a Dynamic-CFD hybrid control model.

Jan 1, 2014

By L. Ya Agapova

Emissions from pyrometallurgical processing of copper concentrates are usually subjected to wet scrubbing. The washing sulphuric acid so produced contains up to 0.2 g/L of rhenium, which is recovered by solvent extraction in the form of crude ammonia permeate (NH4ReO4). The mother liquor, obtained from the sulfuric acid wash, contains up to 35 g/L of rhenium and significant amounts of impurities. Crude rhenium salt is commonly processed by double recrystallization to produce marketable salt. A ton of high grade NH4ReO4 can be produced using 3.0-3.5 m3 of mother liquor. We propose an efficient technology of mother liquor pre-treatment aimed at removal of water-soluble organics with subsequent electrodialysis. Electrodialysis of mother liquor in a multichamber electrodialyzer resulted in the production of pure rhenium acid, from which a marketable NH4ReO4 is precipitated using ammonia solution. Multiple steps of recycling consisting of dissolution of NH4ReO4 salt, rhenium acid production from NH4ReO4 salt by electrodialysis and precipitation of NH4ReO4 from rhenium acid made it possible to upgrade the purity of obtained rhenium compounds by 1-2 orders of magnitude. A rhenium metal powder of 99.997% purity was produced by high-temperature reduction of high-purity NH4ReO4 with gaseous hydrogen. Rhenium metal powder of high purity can be produced from sulfate solutions of NH4ReO4 by non-platinum anode-based membrane electrolysis processes also. Keywords: rhenium, mother liquors, membranes, electrodialysis, rhenium acid, ammonia perrhenate, reduction, powder, electrolysis

Sep 1, 2012

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

The challenges of nature for the recovery of metals for a sustainable future continue to present in diverse ways. Base metal deposits are becoming lower grade and more complex. Rare earth metal demand is soaring and must certainly be met from new sources outside of China. Precious metals have soared in value due to increased industrial usage and the importance of these metals as financial instruments. Many of the future sources of precious metals are complex and difficult to process. The field of hydrometallurgy plays an important role in providing technology for extraction of these metals for a sustainable future. Selected examples from the base, rare and precious metals fields will be used to illustrate how current developments are providing metals for our future. The recovery of rare earths by beneficiation, leaching, purification, precipitation will be described from a multi-mineral deposit in Canada. The recovery of metals from complex base and precious metal ores may be accomplished using chloride ? assisted high temperature pressure leaching. Finally, by way of example, the enhanced Galvanox? process for treatment of chalcopyrite concentrates using silver-activated pyrite as a catalyst will be illustrated. This process offers a viable alternative to the conventional smelting of chalcopyrite copper concentrates.

Sep 1, 2012

By D. W. Lui

Tangdan copper oxide deposit, the largest independent copper oxide deposit in China so far, is located in the northeast of Yunnan province, southwest of China. The ore from this deposit is characterized by: low grade, high oxidation ratio, and fine-grained disseminated, resulting in poor flotation recovery. The analysis of plant flotation data reveals that the loss of copper minerals into tailings is mainly with coarse size fraction due to insufficient liberation and fine size fractions, especially minus 10 microns fraction, which proved to be very difficult-to-float with conventional flotation. In order to improve the performances of plant flotation of this ore, laboratory flotation tests were conducted with the pure malachite, which was the principle copper oxide mineral in Tangdan copper ore deposit. The results obtained suggested that a finer grinding (up to -325 mesh or even -400 mesh) be needed to decrease the loss with coarse size fraction, and vacuum flotation is a promising way for the recovery of the fine malachite effectively.

Jan 1, 2014

By R. K. Dwari

The electrostatic beneficiation of coal is based on tribocharging characteristics of ash forming minerals and coal particles. The tribocharging of quartz, pyrite and coal particles contacted with various metals and polymeric materials have been measured and the charge acquisition is assessed through surface energy calculations from liquid contact angle data. The contact angles, before and after tribocharging of solids, are measured using Krüss tensiometer and Washburn?s method where the sample holders in tensiometer are specially constructed with tribocharger materials. The charge polarity and amount of charge acquired by quartz, pyrite and carbon with metal tribochargers were found in good agreement with the reported work functions of the contacting surfaces. The charge results with polymer materials differed from the work function values, presumably caused by surface contamination. The surface energy of quartz calculated by all the theoretical approaches in the literature showed that the tribocharging increases the surface energy. Both polar and non-polar components computed from Fowkes and Owens-Wendt-Rabel-Kaelble approaches dis-play that both these components increased after triboelectrification. However, the polar component divided into acid and base components, as in van Oss approach, manifest decreasing acid part and increasing base part. Since quartz charged negatively during tribocharging with metal surfaces and therefore accepted electrons, the determined acid and base surface energy components are consistent with charge transfer process. The results also elucidate an explicit correlation between the charges generated by powders and the surface acceptor (acid) and donor (base) electronic states and thereby the work functions. A novel fluidized bed tribocharger was designed and developed with internal baffle system for efficient contact electrification of mineral and maceral to produce high differential charging for efficient separation. The results achieved on coal with 45% ash content are presented and discussed.

Jan 1, 2014

By Patricio Berrios, David Barriga, Peter Amelunxen, Gerson Sandoval, Roger Amelunxen

Laboratory test equipment and methods have undergone relatively little change since their introduction in the 1950’s. The Denver sub-A cell is still by far the most commonly used laboratory batch cell, but bottom-driven and instrumented cells are beginning to appear. Test procedures have also changed little over the past 60 years, and most engineers continue to rely on empirical models for predicted plant scale performance from laboratory scale tests. This approach is problematic, because changes in the froth phase characteristics in the lab hamper the reliability and reproducibility of the empirical extrapolation to plant scale. In a previous work, the authors reported on the impact of froth recovery at the laboratory cell, showing that variability in the froth recovery can lead to significant error in the modeled kinetic rate constant unless it is properly accounted for in the scale-up model. In this work, we review the role of hydraulic entrainment in the lab cell, and how variability in particle specific gravity, shape factor, and froth residence time can impact the entrainment recovery.

Jan 1, 2014

By F. Boylu

In this study, Ca-bentonite was subjected to a series of systematic hydrocyclone tests with the aim of developing separation procedures and in turn achieving optimum recoveries. In hydrocyclone tests, vortex and apex diameters and also feed pressures were investigated. In each hydrocyclone set, vortex diameter was kept constant while the other two parameters varied to produce bentonites con-centrates of various smectite contents. The separation efficiencies were evaluated based on the cation exchange capacity (CEC), particle size and swelling index. The detailed hydrocyclone tests showed that, upgrading of Ca-bentonites require procedures different from the bentonites reported in the literature. Sodium and mixed bentonites are easy- to-disperse and easy-to-separate whereas calcium types need to be scrubbed rigorously for disintegration. Scrubbing properties of ca-bentonite were investigated as a function of scrubbing time and percent solids by weight (PS). The scrubbing conditions at 700 rpm for 1.5 hours and percent solids of 30 % were found more effective for achieving a better quality bentonite. In addition to the parameters mentioned above, the effect of percent solids on hydrocyclone separation was also studied. Although Ca-bentonites permit studying at higher percent solids, increasing solids content of the pulp deteriorated the quality of the clean products. Application of an appropriate separation scheme enabled the development of a unique separation procedure involving stage wise scrubbing followed by hydrocycloning which yielded calcium bentonite concentrates with CEC of 90 meq/100 g and high swelling indexes of 12 mL from the original bentonite of 65 meq/100 g and 7.0 mL, respectively. These results indicate that upgraded bentonite products can be conveniently used in various diverse industrial applications including bleaching earth, desiccant, cat litter, paper etc.

Jan 1, 2014

By Xumeng Chen, Yongjun Peng, Dee Bradshaw

Regrinding rougher flotation concentrates has become a common practice when processing low grade and complex ores. It not only reduces the particle size and improves mineral liberation but also modifies particle surfaces and pulp chemistry due to the strong electrochemical reactions taking place during regrinding. Therefore, the floatability of minerals in the subsequent cleaner flotation is influenced by the regrinding conditions. This paper presents the effect of regrinding conditions on the mineral floatability from both industrial studies in the plant and fundamental studies in the laboratory. Different regrinding conditions were considered, including grinding media, the electrochemical properties of minerals, pulp chemistry (pH, Eh, DO), and breakage mechanisms in tumbling and stirred mills. Results indicate that the selection of regrinding conditions and mill types should not only depend on grinding energy efficiency and liberation but also depend on the surface properties and pulp chemistry produced for effective mineral flotation and separation at the cleaner stage.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

Green pellet strength including drop number and green compression is highly depended on particles size and shape. The used grinding method, ball mill or high pressure grinding roll (HPGR), directly vary the particle size and shape. Considering mode of pellet crack, green pellet is composed of particle-binder-moisture system. Different type of forces existed in such a system to create a stable green pellet: solid particle interaction, magnetic, binding and cohesive forces in the interface of particle-moisture. The pellet failure can occur at solid-liquid interface and/or through liquid phase. Pellet crack occurs when crack passed through entirely the plane failure. In this research, the effect of particle size and shape of pellet feed on green pellet strength has been investigated. It was deduced that green pellet strength highly improved by increase of specific surface area. The drop number and green compression strength of pellets prepared by HPGR was higher than ball mill. It was found that the main reason responsible for this difference was the particle shape. Capillary force is responsible for part of pellet force and improves by decrease of particle size. Also more elongated shape of HPGR particles resulted in higher capillary force due to thinner interface layer between particles. The less circular shape of particles lead to improvement of capillary force as can be occurred for HPGR particles. The rougher shape of HPGR particles resulted in higher wettability of particles and better diffusion of water among particles. In fact the rougher particles means lower connection angle. Aspect ratio of particles was of great importance of crack growth because the required energy of pellet failure increases directly. The required energy for pellet failure increases by increment of particle aspect ratio. The relationship among crack failure force, roughness and aspect ratio has been modeled considering 3 shape descriptors.

Jan 1, 2018

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

By Y. H. Tang

For its surface features, micro-sized hematite is usually difficult to recover by magnetic separation; especially, the existing high gradient magnetic separator in industry can not utilize collecting matrix with thin silky rods for its property of being easily blocked; the lower size limit for recovery of micro-sized weak magnetic minerals is about 0.019mm, some even is 0.037mm. This paper introduces the application of the combined new technique of water-air joint discharging of concentrate and collecting matrix with different diameter silky rods in the field of recovery of micro-sized hematite by high gradient magnetic separator. The commercial test result for recovery of a certain hematite with size about ?0.037mm shows that the recovery can be promoted by 16.81% with basically same concentrate grade.

Jan 1, 2014