Search Documents

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By WenJun Dong

This paper presents the stability assessment of the steel pipe piles that are used to support a deadman beam to anchor an adjacent bulkhead wall. Finite element analyses are performed to assess the stability of the bulkhead wall and determine the required tie-back force to the pile. The piles are relatively close to the bulkhead wall such that their soil resistance wedge zones are not fully developed but truncated by the bulkhead wall. The reduced lateral resistance capacity of the anchor piles is determined by applying the Coulomb wedge method on the truncated soil passive zones between the pile and wall. Both the conventional soldier pile stability (in terms of force and moment equilibrium) and Winkler soil spring (for soil-pile-interaction) analyses are used to assess the stability of the anchor piles.

Sep 8, 2021

Jan 1, 2004

By Pierre Gouvin, Michael Oakland

"This paper covers the rapid response methods used to monitor the emergency response to damage to an historic structure. An architectural gem, the latest incarnation of the old south Church was completed in 1875, utilizing local conglomerate (pudding stone), combined with brownstone and other materials to make an incredible showcase for priceless stained glass and other details epitomizing the height of the American Industrial Revolution. As part of required American with Disabilities retrofits to the adjacent Metropolitan Boston Transit Authority Station (MBTA), a support of excavation system was implemented with tradition sheet piles. During excavation (SOE) it was determined that Jet Grouting would need to supplement the sheeting to close openings in the SOE. During Jet Grouting, the eastern side of the structure was bisected, and lifted over 2 inches up and to the south. The movement occurred rapidly, within minutes, and subsided when Jet grouting was discontinued. The paper will describe the nature of the immediate response to get a real time monitoring program established, and the follow on monitoring program that ensued to provide the needed information to the stakeholders about this critical structure to evaluate stability, safety and to develop a long term remediation plan. The real time systems and instruments used consisted of Automated Motorized Total Stations (AMTS) and Automated Crackmeters. The Paper will describe the techniques used to control construction in safe manner.INTRODUCTIONThe Old South Church of Boston was constructed in 1875 and is one of the best examples of High Victorian Gothic Architecture in the Northeast. (Fig. 1) shows the newly constructed Old South in 1882. The Roxbury Conglomerate used to construct the church combined with large stained glass window by Clayton and Bell of London provides its unique appearance. Like most of the structures constructed in Boston’s Back Bay at that time, the church is founded on timber piles which penetrate the fill and organic soils to bear in the upper Boston Blue Clay. The churches interior includes high vaulted plaster ceilings and a 1920’s E. M. Skinner organ with exposed pipes as long as 32 ft. in length. The Church was added to the list of National Historic Landmarks in 1970 and is a featured Boston attraction."

Jan 1, 2017

By P. Arz

With a total of five basement levels, ground floor and a further six levels above grade, construction of the Kö-Galerie building, on the Königsallee, in the centre of Düsseldorf, was completed with all the difficulties which accompany property development today in the inner city. To meet the intermediate and final deadlines, ad­vanced building techniques were used. Notable among them are the top/down method for simultaneous construction upwards and downwards from an intermediate level, and the use of pre-fabricated composite columns in drilled shafts for the main load-bearing foundations as well as diaphragm walls designed as permanent structural wall of the basement.

Jan 1, 1989

Jan 1, 2003

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Jahnavi Parmar, Pranav R. T Peddinti, Saloni Pandya, P. S. Prasad

Coastal cities are in desperate need of suitable land to meet the ever-increasing demand for urban infrastructure to support commercial, residential, tourism, and off-shore activities. Countries with a lengthy coastal line, such as India, possess significant areas of wide spread highly saline soils subjected to periodic seawater intrusion. One such soil stratum was encountered at the Gulf of Cambay, Bhavnagar district, Gujarat, India. Due to the high volume of river runoff, the Gulf has a positive water balance. The relative humidity ranges from 65 to 86 percent, making the climate semi-arid to sub-humid. The high salinity, mineral content, basaltic origin, and deeper water table offered the impetus to investigate applicability of various soil treatment options for such saline soils. Admixture stabilization techniques have been shown to help with problematic soil features. The Current study aims to determine effectiveness of addition of locally available lignite fly ash (10% - 30% by weight) and cement (6% - 9% by weight) to Bhavnagar saline soil in respect of strength, electrical conductivity and CBR. In this assessment, a comparison of stabilized and unstabilized saline soil mixtures is expected to highlight the need of understanding influence of treatment on instinctive performance of stabilized saline soils, as well as assist practitioners in efficacious treatment of extreme saline soils for diverse geotechnical and construction applications.

Sep 1, 2022

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By G. Ranjan

The designers and the practicing engineers have started using latest and cost effective techniques of ground improvements which utilise the weak and poor sub-soil deposits efficiently for the civil engineering construction. In the present investigation, a new concept of 'skirted granular piles' has been advocated. An effective method of construction of granular piles as an economical alternative to vibroflot, and the skirt has been developed. The construction technique is based on indigeneous know how which effectively utilises the man-power technology avoiding import of costly equipment suiting to the developing countries. Full scale insitu tests have been carried out at four sites, having different soil conditions, on virgin weak sub-soil, and improved ground by casting plain and skirted granular piles. Effectiveness of different types of skirt has been demonstrated through insitu tests. A simple analytical approach has been proposed to predict the ultimate pile capacity. The predicted values of ultimate capacity have been found to demonstrate a good correspondance. Granular pile behaviour in terms of pile depth, diameter, spacing and stress deformation characteristics of the improved ground have been discussed. A significant improvement in ultimate capacity in improved ground has been noted. This is further augmented when granular pile group is skirted.

Jan 1, 2010

By Timothy Nelson, Simon Burnworth

"The Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California, Berkeley campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home.The site was perfect; located one block east of bustling downtown Berkeley and its rapid transit station, and directly across the street from the western entrance to the UC Berkeley campus. Thousands of pedestrians pass by the site on a daily basis, thus granting BAMPFA the opportunity to reshape the corner of Center and Oxford Streets with a building that would not only welcome visitors to campus, but also serve as a creative hub for both the City of Berkeley and the UC Berkeley institution itself 1.The original museum plans, drawn up in the mid-2000s, called for complete demolition of the existing abandoned facility and replacement with a visually stunning structure designed by renowned Japanese architect Toyo Ito. Even at this point, the shoring and means and methods requirements of the project were identified as a challenging component, incorporating a shored excavation bounded on three sides by busy city streets and a fourth side by an operating bank and occupied apartment building. Furthermore, a sequenced demolition would be required for the printing press facility’s three-story Administration Building (also known as the Admin Block), one-story printing press warehouse (also known as the Press Building), and an adjacent parking structure. Degenkolb Engineers was retained at that time as the shoring engineer to design the shoring to facilitate this work."

Jan 1, 2016

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By Lee R. Buhagiar

As a result of the increased seismic risk and the highly variable geology of Christchurch, finding costeffective foundation solutions has been a challenge for the Canterbury rebuild. The soil profile in Christchurch comprises both terrestrial (Springston Formation) and marine (Christchurch Formation) alluvial deposits with a high groundwater table. The result is a highly variable and interbedded soil profile which is prone to liquefaction and static settlement. Vibro-replacement stone columns are very effective in mitigating liquefaction in clean sand. However, the author’s experience has shown that vibro-replacement stone columns are also effective for treating silty and soft soil layers. Vibroreplacement stone columns can be used to treat these soft soils by increasing the composite soil stiffness and providing a load transfer path to the underlying dense soils. Another challenge encountered in the Canterbury rebuild is the cost of redevelopment of brownfield sites with contaminated fill. The costs of disposing this fill often make projects too expensive. Vibro-replacement stone columns have been used successfully to treat contaminated fill, providing a treated soil profile with uniform performance and reducing the cost of disposing of contaminated fill. This paper looks at several case studies in Christchurch, with highly variable soil profiles, where vibro-replacement stone columns have been used successfully to treat multiple soil layers, from contaminated fill to silty soils and soft and non-liquefiable silt.

Nov 1, 2022

By Marco D. Boscardin, Kenneth A. Pidgeon, Adriane G. Boscardin

"Hollow bar tiebacks can offer an economical alternative to conventional solid bar and strand tieback systems for use in temporary excavation support construction. However, the limitations associated with the installation of hollow bar tiebacks require special attention during design, construction and load testing to verify conformance with conventional performance and proof testing criteria (PTI, 2014). In particular, providing a reliable free length is complicated by the 10-foot (3-m) -long, segmental, couplingto- coupling nature of the free length sheath in the hollow bar system, and addressing the fully grouted annulus of the bond zone and the free length zone at the end of installation are key concerns. In addition, it is often more convenient to install a greater number of more closely spaced, lower capacity tiebacks with the hollow bar system, compared to conventional tiebacks. This paper examines how these issues were addressed for a project involving a 60-foot (18-m) -deep sheet pile excavation through a highway embankment and a 70-foot-deep sheet pile and soldier pile and lagging excavation through a railroad embankment, both supported by a hybrid system of hollow bar tiebacks and hollow bar soil nails. The project involved approximately 300 tiebacks and 400 soil nails.INTRODUCTIONEngineers Construction, Inc. (ECI), constructed a pair of 32-foot (9.8-m) -wide (clear span), 30-foot (9- m) -high (21 feet (6.4 m) above the stream bed), cast-in-place concrete arch culverts as a design-build project for the Vermont Agency of Transportation (VTrans) in East Ryegate, Vermont. The new culverts replaced an existing 8-foot (2.4-m) -wide by 6-foot (1.8-m) -high cast-in-place concrete culvert under US Route 5 (RTE5), and twin, 2-foot (0.6-m) -wide by 5-foot (1.5-m) -high granite block culverts under the Washington County Railroad (WACR) alignment. The culverts convey Manchester Brook eastward, through the embankments for RTE5 and the WACR, on its way to the Connecticut River. The Connecticut River is located approximately 100 feet (30 m) east of the WACR embankment. The existing structures were undersized and backed up water behind the embankments during high flow events; and often trapped debris that flowed down the brook and became clogged. The existing culverts also had cracks and openings that have resulted in the loss of ground into the culverts and the formation of sinkholes in the sides of the embankments. Moreover, the reason for the large cross-sectional dimensions of the culverts was to make them of sufficient size and openness to encourage the migration of fish up the stream to spawn. The culvert through the RTE5 embankment is 144 feet (44 m) long, and the culvert through the WACR embankment is 128 feet (39 m) long, with a 57-foot (17.4-m) -long by 32–foot (9.8- m) -wide by 17-foot (5.2-m) -deep 10 feet (3 m) deep above the stream bed) open channel section between the two culverts. A plan view of the culvert alignment is presented in Figure 1."

Jan 1, 2016

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Carlandrea Albonico, Salvatore Miranda

After a brief introduction of the whole Project, the paper describes two special geotechnical engineering solutions provided within the scope of the Galataport Project, in Istanbul, Turkey. The first refers to the new quay of Salıpazarı, which is a combination of retaining structure and ground improvement, formed by a combiwall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The second, refers to the soil improvement works executed underneath three existing buildings. Single-fluid jet grouting columns had the scope of improving the mechanical properties of the bearing soil and reducing the associated risk of liquefaction. A set of underpinning micropiles was installed in order to allow the excavation of a partial basement inside two of these three buildings. All activities were conducted from inside the existing buildings, with reduced headroom. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By D. M. Holloway

As a part of the 1-15 Reconstruction Project, static and dynamic (high-strain) testing methods formed the basis to estimate long-term axial capacities, and to assess the magnitudes of bearing capacity gains (setup) from the end of installation to the time of static/dynamic tests weeks later. This paper summarizes the results of nine full scale pile load tests to failure in compression, and how the designers used these data to finalize pile selection and penetration criteria bridge-by-bridge in the final design stages. Soil conditions along the project alignment ranged from deep, lightly over-consolidated Lake Bonneville clays interbedded with granular strata of varying consistency, to sites dominated by dense alluvial deposits of cohesionless soils well above the water table. The test sites were selected to bracket the conditions that are expected. Twelve-, 16-, and 24-inch-OD pipe piles are to be used to support the new bridges. The team plans to impact-drive all piles closed-end to final penetrations. The test piles varied from 35-ft-long pipes driven to refusal in the shallow dense sands at some sites, to 115-ft-long pipes stopping at 3 blows per foot in predominantly cohesive deposits. The capacities gained with time proved to be reasonably predictable, and significant setup was noted both in the cohesive and cohesionless strata. The test program objectives included providing the means to estimate long-term capacities from short-term (24- to 48-hour) restrikes following installation of foundation piles during production driving operations.

Jan 1, 1998